Professional Documents
Culture Documents
OX/110 - 5
TECHNICAL DATA
GENERAL INFORMATIONS
Voltage When mounting tube inserts adopt proper caution, in order to avoid glass bulb breaking
and fragments projection. Please use protective gloves and glasses.
nominal 110
kV Tube insert connected to H.V. supply is a radiation source: be sure to take all necessary
maximum for test 125 safety cautions
Inverse voltage
nominal 120 Wash thoroughly with alcohol the external surface of tube insert (care of fire risk).
kV Avoid contact of dirty surfaces with cleaned tube insert.
maximum for test 135
Clamp system inside housing or self-contained units must not mechanically stress the
Focal spots (IEC 60336:2005) tube.
small 0.5
mm After installation, check the right working of the tube (no fluctuation of tube current
large 1.5 nor crackling)
Filament characteristics Comply with insert thermal parameters, planning and programming the exposure
small 2.4 ÷ 4.0 V 3.0 ÷ 4.0 A parameters and cooling pauses. Housing or self-contained units must be provided with
4.0 ÷ 8.0 V 3.5 ÷ 4.5 A an adequate thermic protection.
large
Voltages indicated in charts are valid for transformer supplied with ground center.
Anode material tungsten
Tube inserts contain environment polluting materials, particularly lead liner tubes.
Target angle 12 °
Please apply to qualified operator for waste disposal, according to local regulation
Anode heat storage capacity 30000* J requirements.
Maximum anode cooling rate 270* W
Nominal anode input power at 0.1 s (DC)
small 780
W INCIDENT REPORT ACCORDING TO 93/42/EEC MEDICAL DEVICES DIRECTIVE
large 4200
In order to comply with CE marking requirements, end users have to report to local Competent
Inherent filtration 0.5 mm Al Authority all the informations about possible incidents involving the device, regarding any
deterioration in its characteristics and performances, as well as any inaccuracies in this
Maximum diameter 50 mm documentation, which might lead to or might have led to the death of patient / user or a
mm deterioration in his state of health. This information must be promptly reported also to C.E.I. in order
Overall length 145* to start manufacturer reporting, as per above mentioned directive.
* with standard treath. On every kind of treath it is possible to make customized millings
for the allignement of the tube.
0459
this mark assures device conformity to EC Directive 93/42 on Medical Devices Safety
Rev.G – 0310 – Original text: Italian Pag. 1 di 6 C.E.I. Srl – via della Tecnica 3 – San Lazzaro di Savena – BOLOGNA - Italy
compagnia elettronica italiana s.r.l. OX/110 - 5
DIMENSIONS AND CONNECTIONS
STD TREATH
(Anode heat storage capacity 30 kJ, Maximum anode cooling rate 270 W)
Small focus-yellow
raggi
X
THERMAL CURVES
Rev.G – 0310 – Original text: Italian Pag. 2 di 6 C.E.I. Srl – via della Tecnica 3 – San Lazzaro di Savena – BOLOGNA - Italy
compagnia elettronica italiana s.r.l. OX/110 - 5
DIMENSIONS AND CONNECTIONS
LONG TREATH
(Anode heat storage capacity 33 kJ, Maximum anode cooling rate 280 W)
Small focus-yellow
raggi
X
THERMAL CURVES
INSULATING CYLINDER
LEAD Time (s)
Rev.G – 0310 – Original text: Italian Pag. 3 di 6 C.E.I. Srl – via della Tecnica 3 – San Lazzaro di Savena – BOLOGNA - Italy
compagnia elettronica italiana s.r.l. OX/110 - 5
DIMENSIONS AND CONNECTIONS
HEAT SINK
(Anode heat storage capacity 40 kJ, Maximum anode cooling rate 500 W)
Small focus-yellow
raggi
X
Rev.G – 0310 – Original text: Italian Pag. 4 di 6 C.E.I. Srl – via della Tecnica 3 – San Lazzaro di Savena – BOLOGNA - Italy
compagnia elettronica italiana s.r.l. OX/110 - 5
EMISSION CHARACTERISTICS FILAMENT CHARACTERISTICS DC
20 24 4.2
SMALL FOCAL SPOT (0.5 IEC 336)
4.1
16 20
4.0
3.9
16
12
Anode current (mA)
100 120
4.5
LARGE FOCAL SPOT (1.5 IEC 336)
4.4
80 100
4.3
80 4.2
60
Anode current (mA)
Rev.G – 0310 – Original text: Italian Pag. 5 di 6 C.E.I. Srl – via della Tecnica 3 – San Lazzaro di Savena – BOLOGNA - Italy
compagnia elettronica italiana s.r.l. OX/110 - 5
MAXIMUM RATING CHARTS DC
40 kV
50 kV
60 kV
Anode current (mA)
70 kV
80 kV
90 kV
100 kV
110 kV
Rev.G – 0310 – Original text: Italian Pag. 6 di 6 C.E.I. Srl – via della Tecnica 3 – San Lazzaro di Savena – BOLOGNA - Italy