Professional Documents
Culture Documents
Touch screen
—
INSTRUC TION MANUAL
Title bar
Quick start
Status bar
active output (inactive output are not highlighted) settings unlocked by hardware switch
at the back of the controller
Installation
Step 1: Slide the RVT (a) perpendicularly to the capacitor bank cubicle (b). settings can only be done through no demand to switch steps
the communication
Step 2: Rotate the RVT to insert it into the capacitor bank cubicle.
Step 2
(b)
settings can be done through the user automatic mode (steps are switched
interface or the communication automatically according settings
Step 1
(a)
temperature alarm (alarm relay is activated) manual mode (steps can be switched manually)
or warning (fan/warning relay is activated)
Note: cut-out dimensions are 138x138 mm.
Step 3: insert the mounting bracket (c) in the corresponding fixation holes (d) of the RVT.
no temperature alarm nor warning (alarm set mode (settings can be done)
Step 4: pull the mounting bracket backwards.
and fan/warning relays are not activated)
Step 5: turn the screw (e) into the mounting bracket and tighten until the RVT is secured in
place.
warning level achieved (the fan/ mode change validation
Step 3
Step 4 warning relay is activated)
(c)
(d)
More information in alarm activated (alarm relay is activated) online help next page
detailed manuals
Step 5
(e)
Q U I C K S TA R T 3 Q U I C K S TA R T 4
7. Click OK 8. Lock or unlock the “Bank 9. Click OK
settings” and press OK
Commissioning
Before commissioning (both auto and guided), please make sure that:
• RVT is unlocked (both soft and hardware lock)
• RVT is in SET mode
• CTs are properly connected
Messages during an automatic Recommended actions Detailed wiring and direct current & voltage measurements capabilities are shown in the
commissioning process table below, which facilities the selection of different types of connection in terms of in-
Phase rotation was detected to be wrong. L2 and L3 Press OK.
stallation types and requirements on voltage and current measurements.
phases will be internally inverted. Press OK to validated
Error: Step size too small Adapt the step size or the CT ratio.
Error: CT not sensing any current Check that the CT‘s short-circuit bridge are For RVT 6 and RVT12, only the type 1, 2 and 3 are available; RVT12-3P is able to connect in
removed, that CT‘s connections are correctly all eight
Single anddifferent
Three phasetypes of connection.
PFC control types
wired and start the Auto commissioning again.
Error: Load changing too fast Restart the Auto commissioning procedure Connection type Voltages Currents Compensation type
RVT 12 - 3P RVT 6 / RVT 12 Phase shift
under more stable conditions or set the Name Schematics Connection Connection adjustment L12 L23 L31 L1N L2N L3N L1 L2 L3 N Full C31 Full C12 Mixed C3+C1
parameters manually.
Error: Too wide phase dispersion in input nr ‚X‘ ‚Y‘ ‚Z‘ Check capacitor and contactor connections. L2 L2 M
e
M
e
L3 L3
Check capacitor currents for each phase.
a a
0° by default
L2 s s
1Ph-1LL1 CT (see phase shift -
u
- - - -
u
- - - - yes -
L3
Error: At least two CT inputs sensing the same line current Check CT‘s installation. CT
table) r r
e e
Error: No significant current in input nr ‚X‘ ‚Y‘ ‚Z‘ Check that CT‘s short-circuit bridge is d d
lows eight different types of connection topologies based on the type of installation and L1 C C C C
M M M a a a M M a
number of current and voltage transformers:
L2
e e e l l l e e l
L3 0° by default a a a c c c a a c
L1
(Adjust s s s u u u s s u
3Ph-3LL2 L2 - (3) yes yes yes
L3
CT1 - phase rotation u u u l l l u u l
- CT redirection ) r r r a a a r r a
CT2 e e e t t t e e t
RVT6 and RVT12 RVT12-3P d d d e
d
e
d
e
d
d d e
d
L1 C C C C
Type 1 Type 2 Type 3 Type 4 Type 5 Type 6 Type 7 Type 8 L2
a a a M M M M M M a
l l l e e e e e e l
L1 L3 0° by default
1Ph-1LL1 3Ph-1LL1 3Ph-1LN1 3Ph-3LL3 3Ph-3LL2 3Ph-3LN3 3Ph-1LL3 3Ph-1LN3 3Ph-3LN3
L2 N
-
(Adjust
c
u
c
u
c
u
a
s
a
s
a
s
a
s
a
s
a
s
c
u
yes yes yes
L3 CT1 - phase rotation l l l u u u u u u l
- CT redirection ) a a a r r r r r r a
N CT2 t t t e e e e e e t
CT3 e e e d d d d d d e
d d d d
3Ph - 3 LN 3 C
M M M M a
L2
L1 e e e e l
-
0° by default
(Adjust -
a
s
- - - -
a
s
a
s
a
s
c
u
yes yes yes
CT1 u u u u l
C
1Ph: single phase network (L-N or L-L); 3Ph: three phase network L1
L1 M
e
M
e
M
e
M
e
a
l
L2 a a a a c
N 0° by default
L3 s s s s u
3Ph-1LN3 CT1
- (Adjust - - -
u
- -
u u u l
yes yes yes
- CT redirection ) r r r r a
N CT2
e e e e t
CT3 d d d d e
d
1
C3: three-phase capacitor control
2
C1: single-phase capacitor control
Q U I C K S TA R T 7 Q U I C K S TA R T 8
All capacitors are switched on although the required Check setting of phase and C/k values.
reactive power is relatively low.