Professional Documents
Culture Documents
www.fairchildsemi.com
1
Display trend
CRT
CRT LCD,PDP
LCD,PDP OLED?
OLED?
Power
Power :: Fly
Fly back
back LLC
LLC
Backlight
Backlight :: CCFL,EEFL
CCFL,EEFL LED
LED
2
Fairchild Power Devices
LLC FAN7621
controller
3
19’ --- 26’ LCD TV Power (Lips)
Half Bridge
/Push-pull
Output
Rectifier 1 18~24V /Full Bridge
Bridge PFC Circuit Lamp
Rectifier Block
Switching Output
Block Rectifier 2 12V
18~24V
Output
Rectifier 1 Schottky Rectifier
Main 12V 200V Series
Bridge PFC
Switching Output 150V Series
Rectifier Block
Block Rectifier 2 100V Series
60V Series
Output 5V 45V Series
PFC PWM Rectifier 3 40V Series
PFC Control IC
FAN7527B/28/29 Control IC Control IC
FAN4810 Feedback
SG6980 Block
FAN7530 Programmable
FAN6961 T-series FPS Shunt regulator
FAN9612 FSFR2100 Standby Output 5Vsb
FAN431/KA431
Combo FSFR2100U Power Rectifier 4
FAN4800IN/IM FSFR2000
FAN4800A/C FSFR1900
FAN4801/2 FSFR1800 FPS
SG6901/02/05 FSFR1700 FSQ510/FSQ01/02/0365
SG6932 FSBH01/02/0370
FSFA2100 6
6
Introduction of FAN9612
- Interleaved Dual BCM PFC Controller
Efficiency
• Interleaved Æ Lower Turn-off Losses
• Valley Switching Æ Minimize COSS losses
• Strong gate drivers Æ reduce switching losses
• Boost-follower (“tracking boost”) possible
Protection
• Closed-loop soft-start w/ Prog. Ramp Time
• Power and Current Limit per Channel
• Input Voltage Feed-forward
• Secondary Latched OVP
• Input Brown-out Protection
• Line OVP
• Internal maximum fSW clamp limit
7
FAN9612 Efficiency
Improvements
Efficiency vs. Load
Phase Management 100
(115 VAC Input, 400 VDC Output, 400 W)
Efficiency (%)
Valley Switching Technology
• Minimizes COSS losses at turn-on of the MOSFET With Phase Management
90
switching Without Phase Management
Efficiency (%)
Low Start-up and Operating Currents
With Phase Management
90
Without Phase Management
85
0 10 20 30 40 50 60 70 80 90 100
Output Power (%)
8
Efficiency & Cost
Comparison
Single BCM / CRM Interleaved BCM / CRM CCM
ZVS of ZVS (VAC(t) < VO/2 ) or ZVS (VAC(t) < VO/2 ) or NA
MOSFET Valley switching (VAC(t) > VO/2 ) Valley switching (VAC(t) > VO/2 )
Diode Reverse ZCS operation Æ No reverse ZCS operation Æ No reverse Reverse recovery current
Recovery Loss recovery loss recovery loss Æ higher switching loss
Current Small (lower threshold just for Small (lower threshold just for Large (higher threshold for
sensing loss protection) protection) control)
Ripple Higher ripple current -> larger Smaller Ripple currents Smallest Ripple Current
Current conduction loss
Efficiency Good (lower power levels) Best Good (higher power levels)
Inductor Size Small Smallest Biggest
Line Filter High peak currents Æ Larger Smallest line Filter Small line filter
line Filter
Diode cost Inexpensive Diodes Inexpensive Diodes Need SiC / Hyper FR
Diode
Number of Minimal Needs 2 MOSFETs, 2 diodes, Minimal to moderate
Components 2 L’s & 2 CS R’s
Cost Lower Cost (but also limited Low Cost solution (300W- High cost components to
to <300W) 800W) maintain high efficiency
Switching Freq. Variable Frequency` Variable Frequency Fixed Frequency
9
FAN9612 reference material
10
FAN7530 (FAN7529)
CRM PFC Controller
• Superior THD performance
• Voltage mode PWM : No input voltage sensing for power factor
correction Æ power loss saving (80mW,2MΩ)
• Precise output over voltage protection(± 2%)
• Voltage sensing OVP Æ high sensing resistor can be used, power loss
saving (80mW,2MΩ)
• Open feedback protection and disable function(65uA)
Æ No Vcc shut-down circuit is necessary
• Low start-up current : Typ. 40uA
• Low operating current : Typ. 2.5mA
• +500/-800mA peak gate drive current 8-DIP 8-SOP
• Internal RC filter for current sensing
• 8-DIP and 8-SOP package
11
FAN7530(FAN7529)
block diagram
2.5V Vref
Vcc 8
Ref Vc
UVLO
Internal c
Bias
Drive 7 OUT
12V 8.5V Disable Output
150μs 13V
Timer
ZCD 5 S
6.5V Q
1.4V 1.5V
Zero Current R OVP
Detector 2.675V 2.5V
CS 4
Disable
40k 0.45V 0.35V
8pF
Current Protection
0.8V Comparator
Pin Name Function
Ramp
INV Input to Error Amp. Signal Vref
1V Offset Error
Saw Tooth
COMP Output of Error Amp. MOT 3 Amplifier
Generator
(2) Gm
1V~5V 1 INV
MOT Maximum On-time Setting FAN7530
Pin Number Range
CS Current Sense Input
(3) FAN7530 Pin Number
6 2
ZCD Zero Current Detection Input GND COMP
OUT Gate Driver Output
VCC Supply Voltage
GND Ground
12
FAN7530(FAN7529)
Typical Application Circuit
Variable On-time control according to AC line voltage: FCS Patent
13
FAN4800A/C Features
CCM PFC +PWM
• Pin to pin compatible with ML4800 and FAN4800 and CM6800 and
CM6800A.
• PWM configurable for current mode or feedforward voltage mode
operation.
• Internally synchronized leading edge PFC and trailing edge PWM in
one IC.
• Innovative Switching-Charge® multiplier-divider.
• Average-current-mode for input-current shaping.
• PFC over-voltage and under-voltage protections.
• PFC feedback open-loop protection.
• Cycle-by-cycle current limiting for PFC/PWM.
• Power on sequence control and soft-start.
• Brownout protection.
• Interleaved PFC/PWM switching.
14
FAN4800A/C Block Driagram
15
FAN4800A/C Pin Definitions
16
FAN4800A/C
Typical application circuit
17
Introduction of FSFR Series
Features
¾ Variable frequency control with 50% duty cycle for
half-bridge resonant converter topology
¾ High efficiency through zero voltage switching
2 MOSFET (ZVS)
HV IC ¾ Internal Super-FETs with Fast Recovery Type
Body Diode (trr=120ns)
¾ Fixed dead time (350ns)
Advantages through system integration
• High reliability & productivity ¾ Up to 300kHz operating frequency
• BOM cost reduction ¾ Pulse skipping for Frequency limit (programmable)
• Easy design at light load condition
¾ Simple remote ON/OFF control
¾ Various Protection functions: Over Voltage
Protection (OVP), Over Load Protection (OLP),
Over Current Protection (OCP), Abnormal Over
Current Protection (AOCP), Internal Thermal
Shutdown (TSD)
18
Typical Application Circuit
19
FSFR – Series FPS
Block Diagram
20
FSFR – Series Pin Definitions
Pin Pin
No. Name Pin Function Description
This pin is the drain of the high side MOSFET. It is typically connected to the
1 VDL
input DC link voltage.
This pin is for enable/disable and protection. When the voltage of this
pin is above 0.6V, the IC operation is enabled. Meanwhile, when the
2 CON voltage of this pin drops below 0.4V, gate drive signals for both
MOSFETs are disabled.
When the voltage of this pin increases above 5V, protection is triggered.
This pin is to program the switching frequency. Typically, only a resistor is c
onnected to this pin when used for constant frequency PWM mode.
3 RT
Meanwhile, opto-coupler is connected to this pin when used for frequency co
ntrolled resonant mode configuration.
This pin is to sense the current flowing through the low side MOSFET.
4 CS
Typically negative voltage is applied on this pin.
1 2 3 4 5 6 7 8 9 10
5 SG This pin is the control ground. (Signal ground) VDL RT SG L-Vcc VCTR
VFB CS PG H-Vcc
6 PG This pin is connected to the source of the low side MOSFET (Power Ground)
8 NC
9 H-Vcc This pin the supply voltage of the high side drive circuit IC.
This pin is the drain of the low side MOSFET. Typically transformer is
10 VCTR
connected to this pin.
21
FSFA-series
Integrated solution for AHB
• General Features • Typical Application Circuit
• Integrated solution using FAN7622
• 9-SIP with enough creepage
• Internal SuperFETTM with fast-recovery
type body diode (trr<120ns)
• Optimized dead time (200ns) for ZVS
operation
• Design Resources
• AHB design tool Ver 0.9 is now
developing
• AN4153 – Designing Asymmetric PWM
Half-Bridge Converters with Current
Doubler and Synchronous Rectifier • Package Information
using FSFA-series FPSTM
• Lineup
• Up to now, the biggest one (FSFA2100,
0.38 Ω) is released.
22
FAN7621
PFM controller for LLC
• Motivations • Typical Application Circuit
• To cover larger power applications
• To meet a height specification
(less than 10 mm) for some customers
• General Features
• 16-DIP and 16-SOP stand alone
controller
• Variable frequency control with 50% duty
cycle for half-bridge resonant topology
• High efficiency through zero voltage
switching (ZVS) • Pin Configurations
• High-side gate driver included
• Isource is typically 360mA
• Isink is typically 600mA
• Optimized dead time (350ns)
• Up to 300kHz operating frequency
• Pulse skipping for frequency limit
(programmable) at light load condition
• Simple remote ON/OFF control
• Various Protection functions such as
OVP, OLP, OCP, AOCP, and TSD
23
Selection Guide : T-series
24
Introduction of e-Series II
Features
Enhanced surge characteristics with a
specific layout
Avalanche rugged internal current sensing
sense-FET
TO-220
Simple sync detection circuit – only 2 resistors
are needed
Better efficiency through valley switching and
hybrid control – patent pending
Extremely narrow frequency range owing to
hybrid control
Low EMI through valley switching, inherent
frequency modulation and AVS(Alternating Maximum output power
25
What is the benefit using e-Series II?
- Extremely narrow frequency range
Conventional QRC
e-Series I
e-Series II
26
26
What is the benefit using e-Series II?
- Better efficiency thru valley switching and
hybrid control
Quasi-resonant operation requires DCM design, which results in increased conduction
loss especially at low line.
E-series II FPS operates in CCM at low line and in valley switching & AVS at high line
Æ Efficiency is not deteriorated at low line.
27
e-SeriesII FPS - Block diagram
28
e-SeriesII FPS – Pin definition
Pin # Name Description
1 Drain SenseFET drain. High-voltage power SenseFET drain connection.
2 GND Ground. This pin is the control ground and the SenseFET source.
3 Vcc Power Supply. This pin is the positive supply input. This pin provides internal operating
current for both start-up and steady-state operation.
4 FB Feedback. This pin is internally connected to the inverting input of the PWM comparator.
The collector of an opto-couple is typically tied to this pin. For stable operation, a
capacitor should be placed between this pin and GND. If the voltage of this pin reaches
6V, the overload protection triggers, which shuts down the FPS.
5 Sync Sync. This pin is internally connected to the sync-detect comparator for quasi-resonant
switching. In normal quasi-resonant operation, the threshold of the sync comparator is
1.2V/1.0V.
6 Vstr Start-up. This pin is connected directly, or through a resistor, to the high-voltage DC link.
At start-up, the internal high-voltage current source supplies internal bias and charges
the external capacitor connected to the Vcc pin. Once Vcc reached 12V, the internal
current source is disabled. It is recommended to connect Vstr and Drain together.
29
Information of e-SeriesII FPS
• Lineup
31
Introduction of FSQ510
TM
New Green FPS e-Series supports environment friendly systems through
• Hybrid PWM Controller allows both fixed frequency PWM and QR-PWM
• Low standby power consumption less than 60mW for FSQ510
• Better efficiency by soft switching technology (QRC)
• Low EMI by inherent frequency modulation and minimum voltage switching
• Enhanced thermal performance by minimized switching loss
• High reliability by strong protections
GND Vstr
GND D
FSQ510
Vfb
Sync Vcc
7 DIP
32
FSQ510 for Standby Power
33
E-Series I FPS (FSQ0365/0265/0165/321/311)
Features
• Optimized for Quasi-Resonant Converter (QRC)
• Low EMI through Variable Frequency Control and Inherent Frequency Modulation
• High Efficiency through Minimum Voltage Switching
• Narrow frequency variation range over Wide Load and Input Voltage Variation
• Advanced Burst-Mode Operation for Low Standby Power Consumption and minimized audible
noise (standby power consumption less than 1 W for 0.5W load)
• Pulse-by-Pulse Current Limit
• Various Protection functions: OLP, OVP, AOCP, TSD
• Under Voltage Lock Out (UVLO) with Hysteresis
• Internal startup circuit
• Internal High Voltage Sense FET (650V)
• Built-in Soft Start (15ms)
• Code S: Now
34
e-Series I FPS Block Diagram
35
Lineup of e-Series I FPS
36
QRC Controller:FAN6300
• FEATURES
• Quasi-Resonant Operation
• Over Power Compensation (DET Pin) QRC, High Average Eff.
Features
• Internal 4mS Soft-Start High Cost-Efficient
• Internal Minimum Toff 8uS
• Internal Leading Edge Blanking
• Cycle-by-cycle current limiting
• Peak current mode control
• High Efficiency
• PROTECTION NC
OVP (Latched)
SG6300
FAN6300
37
QRC Controller:FAN6300
Typical Application Circuit
HV Startup
Vo+
BD1
C1
Vo-
VAC
•Valley Detect for QR Operation
•H/L line Over Power Compensation
•Output Voltage OVP (Latched)
6
CCM Operation Quasi - Resonant Operation
8 HV VDD DET 1 VDS VDS
VDS -ON = n ⋅ Vo + Vin
7 NC GATE 5
2 FB CS 3
GND
4 n ⋅ Vo n ⋅ Vo
Vin Vin
VDS -ON
• Auto-recovery Open-Loop
1
Protection PLOSS = ⋅ Coss ⋅ VDS -ON 2 ⋅ Fs
2
38
QRC Controller:
FAN6300 - Green Mode Operation
Toff=500us
Gate
High
High Efficiency
Efficiencyat
at Light
Light Load
Load
VFB
VDS
Burst Frequency
OUTPUT POWER
39
QRC Controller:
FAN6300 - No load & Light load &
Efficiency test result
Test Board: NB 90W 19V
QRC, High Average Eff.
Features
(PFC:FAN6961+QRC:FAN6300) High Cost-Efficient
40
Introduction of FAN6755
41
FAN7602C
- Green Function Current Mode PWM IC
Features
Vstr NC Vcc OUT
42
FAN7602C
- Green Function Current Mode PWM IC
Block Diagram
TSD
OVP
Frequency
Modulation
Burst Mode
&
Soft Start
Latch &
Power Limit Over Load Protection
43
6PIN PWM Controller : SG6859A
A
• Built-in Slope Compensation
59
• Frequency hopping
68
SG
• Open-loop protection
44
SSR Controller: SG6859A
VDD-ON 25V
VDD-OFF VDD
FB
Saw Limiter
Current-sense signal High Line Low Line
45
FSC Inverter Product Line - up
Features
Generation Products Description Status
Vcc (V) Dimming Soft Start OLP OLR(=OVP) SCP Vout(Max) Iout(Max)
FAN7547A 1Ch. Buck-Royer 6 ~ 30 Analog, Burst O O O X Vcc 0.2A S
0G
FAN7548 2Ch. Buck-Royer 9 ~ 30 Analog, Burst O O O X 13.5V 0.2A S
FAN7316 N-N Half Bridge 4.5 ~ 24 Analog, Burst O Internal (4) O O 6V 0.5A S
2nd G
FAN7317 P-N Full Bridge 6 ~ 24 Burst O Internal (4) Internal (4) SLP 6V 0.2/0.3A S
FAN7318 P-N Half Bridge 6 ~ 30 Analog, Burst O Internal (4) Internal (4) SLP 8V 0.3/0.4A D (P12)
3rd G FAN7320 H/B Switch Integration 9 ~ 25.5 Analog, Burst O Internal (4) Internal (4) SLP Ron=30mΩ S
46
FAN7313
Block Diagram & Features
Features
• High Efficiency Single Stage Power
Conversion
• Wide Input Voltage Range : 4.5~25.5V
• Precision Voltage Reference : 2%
• Reduces Number of Required External
Components
• Push-Pull Topology
+
• Soft Start
• PWM Control at Fixed Frequency
• Analog and Burst Dimming
• Striking Frequency (=1.3* Fnormal)
• Open Lamp Protection
• Open Lamp Regulation
• Short Circuit Protection
• 20 Pin SOIC
47
FAN7313
Push-Pull Application Circuit
F1
FUSE C1 C2
220u 1u C3
1u
OLP3 OLP4 OLR
LTM190EX
0 0 0 0 0 0 TX1
0 R28 R29 1
HOT
33 33
CN1
35001WR-02A
R2 R3 C5 R1 2
100k 100k 10n 27k COLD
C24 C25
2.2n 2.2n
M1 1
HOT
OLR
OUTH
RT
OLP3
OLP4
VIN
BCT/FT
SCP
VS
VB
0 C9 CN2
FAN7313
SN DN C8 15p 35001WR-02A
15p 2
COLD
IC1
GN DN D2 OLP2
C22 BAV70 R5 OLP1
OUTL
VREF
OLP1
OLP2
BDIM
GND
CMP
330p
ENA
0 DN 1k 10n 10n
FB
SN
CN5 GN DN
0 0 0 0 D3
1 C12 HUFA76413DK8 BAV70
2 14V 33n R6 R7
3 R8 R9 680 680
4 100k 100k
5 0 C13
6 1u
7 DIM(0~3.3V) 0 0
8
9 ON/OFF 0 0
10 R22 TX2
1
HOT
12505WR-10 OLP1 OLP2 47k CN4
REF C23 R23 35001WR-02A
0 R13 10n 100k 2
10K COLD
R12
R10 56k 0 0
22k
1
HOT
C14 R11 CN3
10n 18k C15 C16 35001WR-02A
15p 15p 2
COLD
D4 OLP4
0 0 OLR BAV70 C19 OLP3
R20 R14 C18 R15 10n
C21 R18 1k 10n 1k
10k 4.7n 100k
C17 0 0 0 0
10n D5
0 0 BAV70
0 R16 R17
R21 680 680
8.2k 0 0
C20 R19
1n
10k
0
0
48
FAN7313
P-N Half-Bridge Application Circuit
F1
FUSE C1 C2
220u 1u C3
1u
RT
OUTH
R24 Q1 GP
VIN
OLP3
OLP4
BCT
SCP
VS
VB
750R 2N2222
FAN7313
OLP1 OLP2
FDD8424H R4 C10 R5 C11
IC1
1k 4.7n 1k 4.7n
R26 Q2
OUTL
VREF
OLP1
OLP2
BDIM
ADIM
1k 2N2907 R6 R7
CMP
GND
ENA
0 0 0 0 D3 680 680
FB
BAV70
M2 0
2N7002 0 0
R8 R9 C12 0 R25
100k 100k 33n
0 R22 0R
TX2 1
R13 100k 1
CN5 OLP1 OLP2 100k C23 R23 C13 0 CN4
10n N.C. 1u 35001WR-02A
1 REF 2
2 14V 2
3 1
4 R12 0 0 0 1
5 R10 75k CN3
6 12k D4 C15 C16 35001WR-02A
7DIM(0~3.3V) 0 BAV70 5p 5p 2
8 2
9ON/OFF
10 C14 R11 OLR OLP3 OLP4
10n 9.1k R14 C18 R15 C19
C24 R18 1k 4.7n 1k 4.7n
12505WR-10 4.7n 100k
0 R20 0 0 R16 R17
0 0 0 0 D5 680 680
0 0 BAV70
10k C17
10n R21 0 0
0 10k
C20 R19
1n
10k
0 0
49
FAN7316
Block Diagram & Features
Features
1.25V -
DRV 6V VREF
ENA +
Internal
200k
VIN
Voltage
Reference • High Efficiency Single Stage Power
VIN +
UVLO 4.5V -
UVLO
Conversion
+ + SCP
3V - - 2V
• Wide Input Voltage Range : 4.5~24V
Timer
+ 32 BCT cycles @
Normal TSD 150oC
• Precision Voltage Reference : 2%
0.25V
1.75V - 1.5s @ Strike,
Foscb=300Hz • Reduces Number of Required External
OLR VREF
-
2V +
Protection Components
BDIM
Disable @ Striking
FAULT
FAULT
VB
• N-N Half-Bridge & Push-Pull Topology
BDIM
1) ADIM>3.5V(hys. 0.5V) : Negative
2) ADIM<3.0V(hys. 0.5V) : Positive Controller VBURST 3V
OUTH
• Soft Start
max. 2V
BCT/FT
min. 0.5V
0.45*Va + Input
Drivers
VREF
VS
• PWM Control at Fixed Frequency
Control
- Logic
VSS_STK
OUTL
• Analog and Burst Dimming
GND
FB
2V
-
+
Output
Control
• Striking Frequency (=1.3* Fnormal)
ADIM + Logic
Va
Error Amp.
1.5s @ Strike
10ms @ Normal
max. 2V
• Open Lamp Protection
min. 0.5V
CMP OSC
VSS_STK
RT
• Open Lamp Regulation
Fstrike: Fnormal = 1.3:1
VSS_STK
• Short Circuit Protection
OLP1 - - OLP3
• 20 Pin SOIC
1.5V + + 1.5V
OLP2 - - OLP4
1.5V + + 1.5V
50
FAN7316
N-N Half-Bridge Application Circuit
F1
FUSE C1 C2
220u 1u C3
1u
OLP4
RT
OUTH
VIN
BCT
SCP
VS
VB
SN2 DN2
FAN7316
OLP1 OLP2
GN2 DN2 R4 C10 R5 C11
IC1
1k 4.7n 1k 4.7n
D1
D1N4148 FDS6990A
VREF
OUTL
OLP1
OLP2
BDIM
ADIM
R6 R7
CMP
GND
ENA
0 0 0 0 D3 680 680
FB
BAV70
0 0
R8 R9 C12 0
100k 100k 33n
0 R22
C13
1u TX2 1
R13 100k 1
CN5 OLP1OLP2 100k C23 R23 CN4
10n N.C. 0 35001WR-02A
1 REF 2
2 14V 2
3 1
4 R12 0 0 1
5 R10 75k CN3
6 12k D4 C15 C16 35001WR-02A
7DIM(0~3.3V) 0 BAV70 5p 5p 2
8 2
9ON/OFF
10 C14 R11 OLR OLP3 OLP4
10n 9.1k R14 C18 R15 C19
C24 R18 1k 4.7n 1k 4.7n
12505WR-10 4.7n 100k
0 R20 0 0 R16 R17
0 0 0 0 D5 680 680
0 0 BAV70
10k C17
10n R21 0 0
0 10k
C20 R19
1n
10k
0 0
51
FAN7316
Push-Pull Application Circuit
F1
FUSE C1 C2
220u 1u C3
1u
OLP3 OLP4 OLR
LTM190EX
0 0 0 0 0 0 TX1
0 R28 R29 1
HOT
33 33
CN1
35001WR-02A
R2 R3 C5 R1 2
100k 100k 10n 27k COLD
C24 C25
2.2n 2.2n
M1 1
HOT
OLR
OUTH
RT
OLP3
OLP4
VIN
BCT/FT
SCP
VS
VB
0 C9 CN2
FAN7316
SN DN C8 15p 35001WR-02A
15p 2
COLD
IC1
GN DN D2 OLP2
C22 BAV70 R5 OLP1
OUTL
VREF
OLP1
OLP2
BDIM
GND
CMP
330p
ENA
0 DN 1k 10n 10n
FB
SN
CN5 GN DN
0 0 0 0 D3
1 C12 HUFA76413DK8 BAV70
2 14V 33n R6 R7
3 R8 R9 680 680
4 100k 100k
5 0 C13
6 1u
7 DIM(0~3.3V) 0 0
8
9 ON/OFF 0 0
10 R22 TX2
1
HOT
12505WR-10 OLP1 OLP2 47k CN4
REF C23 R23 35001WR-02A
0 R13 10n 100k 2
10K COLD
R12
R10 56k 0 0
22k
1
HOT
C14 R11 CN3
10n 18k C15 C16 35001WR-02A
15p 15p 2
COLD
D4 OLP4
0 0 OLR BAV70 C19 OLP3
R20 R14 C18 R15 10n
C21 R18 1k 10n 1k
10k 4.7n 100k
C17 0 0 0 0
10n D5
0 0 BAV70
0 R16 R17
R21 680 680
8.2k 0 0
C20 R19
1n
10k
0
0
52
FAN7317
Block Diagram & Features
Features
• High Efficiency Single Stage Power
Conversion
• Wide Input Voltage Range : 6~24V
• Precision Voltage Reference : 2%
• Reduces Number of Required
External Components
• ZVS P-N Full-Bridge Topology
• Soft Start
• PWM Control at Fixed Frequency
• Burst Dimming
• Programmable Striking Frequency
• Open Lamp Protection
• Open Lamp Regulation
• Short Lamp Protection
• 20 Pin SOIC
53
FAN7317
P-N Full-Bridge Application Circuit
F1
1
HOT
FUSE C1 C2 C4 CN1
220u 220u C3 C5 5p CCFL
1u 1u 2
CN2 M1 COLD
OLR1 OLP1
1 0 0 0 0
2 0
13V R1 SN DN R2 C6 R3
3 OLP4 OLR4 OLR3 OLP3 10k 3.3n 180
4 0 OUTB T1
5 10k 0 0 GN DN
6 C8 R4 C7 10u
7 10n 0 0 0
8 SP DP
9 ON/OFF C10 C11 C12 10k C9 10u
10 0 220p 33n 1u OUTA 1
GP DP HOT
C13 CN3
12505WR-10 FDS8958A 5p CCFL
2
CT
VIN
CMP
OLR4
OLR3
ENA
OLP4
OLP3
0
OUTB
OUTA
COLD
OLR2 OLP2
FAN7317
R5
100k R6 C14 R7
BDIM(0~3.3V) 10k 3.3n 180
M2
REF(5V)
0 0 0
OUTD
OUTC
IC1
R8
OLR1
OLR2
OLP1
OLP2
BDIM
GND
BCT
R9 56k SN DN
22k
T2 1
GN DN
HOT
REF R11 C16 CN4
C15 R10 5p CCFL
10n 18k SP DP 2
C17 C18 0 10k COLD
1u 4.7n OUTC OLR3 OLP3
GP DP
0 0 R12 C19 R13
OUTD FDS8958A 10k 3.3n 180
0 0 OLP1 OLR1 OLP2 OLR2
R14
0 0 0
1.4M
1
HOT
C20 CN5
5p CCFL
2
COLD
OLR4 OLP4
0 0 0
54
FAN7318
Block Diagram & Features
Features
High-Efficiency Single-Stage Power
Conversion
Wide Input Voltage Range: 6V to 30V
Backlight Lamp Ballast and Soft Dimming
Minimal Required External Components
Precision Voltage Reference Trimmed to 2%
P-N Half-Bridge Topology
Direct PMOS Drive Circuit
Soft-Start
PWM Control at Fixed Frequency
Negative Analog Dimming Function
Negative Burst Dimming Function
Programmable Striking Frequency
Open-Lamp Regulation
Open-Lamp Protection (disabled by ENA
voltage)
Short-Lamp Protection (disabled by ENA
voltage)
CMP-High Protection (disabled by a pull-
down resistor)
High-FB Protection
Thermal Shutdown
20-Pin SOIC
55
FAN7318
4 lamps application circuit
56
FAN7318A
Block Diagram & Features
Features
High-Efficiency Single-Stage Power
Conversion
Wide Input Voltage Range: 6V to 30V
Backlight Lamp Ballast and Soft Dimming
Minimal Required External Components
Precision Voltage Reference Trimmed to 2%
P-N Half-Bridge Topology
Direct PMOS Drive Circuit
Soft-Start
PWM Control at Fixed Frequency
Negative Analog Dimming Function
Negative Burst Dimming Function
Programmable Striking Frequency
Open-Lamp Regulation
Open-Lamp Protection (disabled by ENA
voltage)
Short-Lamp Protection (disabled by ENA
voltage)
CMP-High Protection (disabled by a pull-
down resistor)
High-FB Protection
Thermal Shutdown
16-Pin SOIC
57
FAN7318A
2 lamps application circuit
58