Professional Documents
Culture Documents
30
80 130
132
EU.T. EU.T.
245
322
G3 F7
660
740
5R
335
206
80
305 610 610 915
1,525 915
L1-230kg L2-153kg
2,440
50
346.5
1,015
322
915
346.5
50
airCalc++ v. 2.1.16 Update Nr. 09FB0
Offer AHU
Position 01
AHU-01 EU.T. EU.T.
Project PSMMC AHU G3 F7
[Pcs] 5R
Drawing 01 1
Date 2/24/2021
Client AMBIENCE DOM
Street
Client re&quest no
Revision Execution Indoor Unit
Weight [kg] 383
TECHNICAL DATA
specific fan power [W/m3/s] 1173
ZHK 2000 S EU 1253/2014 compliance out of scope
Supply air Size:9/6 Weight:383 [kg] Surface: 8.0 [m2] Velocity: 1.63 [m/s]
design M1-FTH-K-V Dimensions [mm] L: 2,440.0 W: 1,015 H: 740
Air volume [cfm] 1,925 Panel inside 50 [mm] galvanized steel 1.00 mm
external pressure drop [Pa] 249 Panel inside bottom galvanized steel
total pressure drop [Pa] 636 Guides galvanized steel
Specific fan power [w/m3/s] 1,173 Panel outside White A47SME 0.70 mm
M1 Simple mixing section 305.0 [mm] 1.04 [m2] 44.00 [kg] 13 [Pa]
Recircle air [cfm] [°C] [°C] Mixed air [°C] Rel. humidity [°C]
Fresh air [cfm] [°C] [°C] Mixing ratio
Opening: 3 Top opening Dimensions [mm] 915.0 x 245.0
( 23 ) Damper Frame GI seal lip No 13 [Pa]
torque [Nm] 1.5 Blades GI Blade drive Gearwheels , PPGF
Axle 1 drive type Suitable for actuator, in air dir. right
Opening: 1 Rear top Dimensions [mm] 915.0 x 245.0
( 23 ) Damper Frame GI seal lip No 13 [Pa]
torque [Nm] 1.5 Blades GI Blade drive Gearwheels , PPGF
Axle 1 drive type Suitable for actuator, in air dir. right
Offer AHU
Drawing 01 Pieces 1
Position 01 Rev. Nr.
Unit AHU-01 Rev. date
FTH Bag Filter section with prefilter 610.0 [mm] 1.86 [m2] 69.00 [kg] 160 [Pa]
Manufacture General Filter Cells pcs x size [mm] 3 x 592.0 x 287.0
Type CFW30-048-G3 tmax.=70°C
Class ISO 16890 Coarse 50%
Init.-Dim.-Fin. press. drop [Pa] 33-58-83
Airflow [cfm] 1,925 Galvanized frames ( front removable ) clean air side
filter thickness [mm] 48.0
Filter surface [m2] 0.87
Final pressure drop acc. OM-5-2019; table 3
Manufacture AAF Filter surface [m2] 6.00
Type DriPak Base SF Ultra-F7 tmax.=70°C Cells pcs x size [mm] 3 x 592.0 x 287.0
Init.-Dim.-Fin. press. drop [Pa] 52-102-152
Class ISO 16890 ePM2.5 50%
Airflow [cfm] 1,925
Bag length [mm] 508.0
Filter energy class (EN 779:2012) n.a.
Final pressure drop acc. OM-5-2019; table 3
Standard hinged door EU.T. Access side: right Dimensions [mm] 457.5 x 610.0 -[L]
( 300 ) 1 Pcs Door lock
( 178 ) 2 set Pressure test points mounted
K Cooling coil 610.0 [mm] 1.86 [m2] 117.00 [kg] 128 [Pa]
Airflow [cfm] 1,925 Density [kg/m³] 1.11 Medium Water
Coil face velocity [m/s] 2.36 SHR 0.7 Med. Flow [l/s] 0.7700 Content 12.9 l
Air in [°C] 26.66 Humidity [°C 19.44 Med. velocity [m/s] 1.00
Air out [°C] 13.43 Humidity [°C] 13.10 Med. in [°C] 6.00
Capacity [kW] 19.34 Med. out [°C] 12.00
air-side humid p.d. [Pa] 118 Med. pres. drop [kPa] 22.72
40x34-AR/2.5pa/5R-13T-741L-4N/V1/CU-GW-1"/CU-AL-FeZn/LT906-HT595-C215/ARI
nos. of rows 5 Max press. [bar] 21 Connection side right
nos. of circuits 4 Fins AL
Fin spacing [mm] 2.50 Tubes CU
Connection in 1" threaded Header CU
Connection out 1" threaded Frames GI
( 134 ) 1 Pcs Drain / air vent
Drain pan AISI 304 - H: 60.0 mm - sloped drain pan Size 610.0x915.0 Ø1" not threaded
Drip eliminator Model TA144 Quality frame GI Quality fins PPTV 10 [Pa]
Offer AHU
Drawing 01 Pieces 1
Position 01 Rev. Nr.
Unit AHU-01 Rev. date
V Supply air-Centrifugal fan / belt driven 915.0 [mm] 3.25 [m2] 153.00 [kg] 43 [Pa]
Fan Nicotra/Gebhardt / RDH E0-0250 Motor Elvem 6T2 80B-2
Air volume [cfm] Density [kg/m³] 1.11 ) 1,925.00 Protection IP55
External press [Pa] 249 Insulation class F
dyn.press.drop [Pa] 43 Nominal power [kW] 1.100
Tot. pressure [Pa] 636 Speed +-2% [1/min] 3,420
Speed [1/min] 2,898 Current +-5% [A] 2.42
sound power [dB(A)] 86.9 Nom. voltage (+-5%) 3x400 V - 60 Hz
shaft capacity [kW] 0.799 Starting mode Suitable for freq. inv.
efficiency [%] 72.0 Winding Type 230V D / 400V Y
maximale RPM [1/min] 4,600 Efficiency +-2 [%] 79
Fan outlet [mm x mm] 322.0 x 322.0 / V1 Electrically absorbed power [kW] 1.23
Calibration faktor [m²s/h] 95 operating point of FC [Hz] 60.3
Motor efficiency class IEC60034: IE 2
Fan pulley Bush Transmission eff. [%] 81
Motor pulley Bush Axle distance ca. [mm]
Belt [mm] fan connection : Flexible canvas
pulley work diameter [mm] Temperature increase fan section [°C] 1.2
Fan octave band sound power level (Lokt) [dB] Antivibration insulators Spring insulators
Frq. [Hz] 63 125 250 500 1000 2000 4000 8000 Pos. 1 1xISOTOP MSN 5 Pos. 3 1xISOTOP MSN 4
Inlet 76 77 77 82 78 77 71 64 Pos. 2 1xISOTOP MSN 4 Pos. 4 1xISOTOP MSN 3
Outlet 91 87 83 82 81 82 74 66 Pos. 5 Pos. 6
( 21 ) 1 set Fan-motor assembly galvanized
( 22 ) 1 set Equipotential wire M10, Spring isolators SD
( 41 ) 1 set Protection PTC 1 x M16
( 47 ) 1 set Motor precabeled
( 53 ) 1 set Gland for power cable 1 x M20
( 35 ) 1 Pcs Protection grid inspection door galvanized
Standard hinged door EU.T. Access side: right Dimensions [mm] 610.0 x 610.0 -[R]
( 300 ) 1 Pcs Door lock
Offer AHU
Drawing 01 Pieces 1
Position 01 Rev. Nr.
Unit AHU-01 Rev. date
Safety and unloading instructions supplied in printed form together with the AHU
Please download maintenance & service instructions with the following QR-Link
Euroclima participates in the ECP programme for: Air Handling Units (AHU). Check ongoing validity of certificate: www.eurovent-certification.com