Professional Documents
Culture Documents
System software
Operation Manual
Catalog
Elevator IC card operation manual
Catalog................................................................................................................................................2
I elevator control system software operation environment..........................................................4
II elevator control system software installation.............................................................................4
1 、Install elevator control system software..............................................................................4
2 、Unload elevator control system software............................................................................8
III The usage of management system software..................................................................12
1、Composition of TIBOSHI management system.................................................................12
2、Log in..................................................................................................................................12
3、Change password................................................................................................................12
4、System subscriber foundation.............................................................................................13
5、Price setting.........................................................................................................................14
6、Elevator information...........................................................................................................15
7、Communication port setting................................................................................................17
8、Setting Backup Position......................................................................................................18
9、Proprietor card making.......................................................................................................19
(9.1)Make charging card..........................................................................................19
(9.2)Make another card for lost card.....................................................................22
(9.3)Card charging....................................................................................................23
(9.4)make time period card.....................................................................................23
(9.5)Re-issue time period card...............................................................................26
(9.6)extending usage time.......................................................................................27
10、Collecting Fingerprint.......................................................................................................28
(10.1) Collecting Fingerprint....................................................................................28
(10.2)Changing Fingerprint.....................................................................................31
11、Management Card Making................................................................................................34
(11.1)make management card......................................................................................34
(11.2)make re-issued management card..............................................................36
(11.3)make compulsory management card.................................................................38
(11.4)Make card for setting button time................................................................39
(11.5)make card for setting controller’s time........................................................40
(11.6)make card for reading proprietor data.........................................................41
(11.7)make corresponding time card for visitor button.......................................42
(11.8)make time period card for setting elevator operation........................................43
(11.9) Making the Card for Deleting the Password........................................................44
(11.10) Making the Card for Setting Date Management................................................45
(11.11) Making Layered Management Card............................................................47
(11.12) Reading the Records on Swiping the Card................................................48
12. Long Distance Control........................................................................................................49
(12.1) the Process of Shield Card...................................................................................50
(12.2 )Setting Response Time of the Button.........................................................51
(12.3) Setting the Time of the Controller...................................................................52
(12.4) Long Distance Monitoring..................................................................................53
(12.5) Long Distance and Real Time Monitor............................................................54
(12.6 )Elevator Control...................................................................................................55
2
Elevator IC card operation manual
3
Elevator IC card operation manual
environment
installation
There is no difference between installation of elevator control system software and other Windows
application procedures. Users just operate setup.exe of elevator control system and then install
1. Enter Windows operation system and operate “setup.exe” of elevator control system to install
procedure. Then the interface will show a picture as follow:
4
Elevator IC card operation manual
button, then the interface will show dialog install catalog selection as follow :
( Picture 1-2)
5
Elevator IC card operation manual
( Pictu
re 1 –2 )ready to install
3. Users select installation catalog of elevator control system card. If you select
button, then it will show the dialog browse files (picture 1-3). If you don not
6
Elevator IC card operation manual
7
Elevator IC card operation manual
There is no difference between unloading of all-purpose card software and other Windows
application procedures. Users just operate on control panel under prompts step by step.
1. Enter Windows operation system and click start menu and let the cursor to select control panel.
8
Elevator IC card operation manual
9
Elevator IC card operation manual
control system 2.0. Double click button to prepare to unload elevator control system
software. (Picture2-3 )as follow:
The screen will show the dialog Add or Remove Programs to confirm whether the user unloads the
5. Unload
Let the cursor click button to unload . Then you will see a dialog which will show
10
Elevator IC card operation manual
11
Elevator IC card operation manual
While using management system software, we should know the use and composition of the
software and the operator can easily operate the software according to manual introduction.
Sketch of system use: Operate in order if you use it for the first time.
System subscriber foundation (details in IV System subscriber foundation)
Unit price setting: (details in V Unit price setting)
Maintains of elevator information (details in VI elevator
information)
Communication port setting (details in VII communication port setting)
Use the above operations while you first operate. Then you needn’t operate the above
operations while you do some business of making card.
After the above operations, you can do some business of making card. Detail operation please
see the introduction.
2、Log in
Step one: After opening the software, there will be a log-in frame which needs manager’s
name and password. If the system is installed for the first time, the manager’s name is
Step two: When the manager’s name and password is confirmed, the main interface of
software will show you. Then the manager can operate normally.
12
Elevator IC card operation manual
3、Change password
Step two: Click the button and then pop-up an interface of changing passwords .
( Picture as follow)
Step three: Input default passwords and new passwords. The twice new passwords should
match each other.
4.1. Step one: Click system setting on platform of elevator control system software .
(picture as follow)
13
Elevator IC card operation manual
Open the window user management click and input number 、user name and allow
this subscriber use after charging. Then set the subscriber’s passwords and authority and click the
14
Elevator IC card operation manual
5、Price setting
Step one: Click system setting on platform of elevator control system software. The picture
is as follow:
Note : unit price setting can set unit price of different floor, while making
card according to the unit price of the highest floor.
15
Elevator IC card operation manual
6、Elevator information
Step one: Click system setting on platform of elevator control system software. The picture
is as follow:
Note : Elevator serial No. : While making card, it means elevator No. while
remote communication, it means elevator Office No;
16
Elevator IC card operation manual
elevator name: you can write randomly but you should remember the elevator
serial No. so as to select the corresponding elevator No. while making card.
Floor No.: you can write according to actual floor. (Include all floor controlled by
elevator IC card controller.) or write more than actual floor No.
Type of elevator can be written according to actual situation.
Step one: Click system setting on platform of elevator control system software. The picture is
as follow:
Step two: Click to open the interface for setting communication port.
17
Elevator IC card operation manual
Step three: Write and read the COM port connecting with the device according to elevator
actual situation.
18
Elevator IC card operation manual
Step II: Click to open the interface for setting backup position as
follows:
Step III: Fill suitable database backup position according to actual status of the
user.
Step IV: Click the button to complete the database backup position.
Note: above dialog box will pop up while closing this system if there is no
backup position set for the first time of use, and the backup position must be
added in case of unpredictable problems.
Proprietor card making is to make card which the proprietor uses. It includes charging card
Step two: Click left side of the main interface to open new card issue
19
Elevator IC card operation manual
interface.
Step three: Click to connect reader. Then the prompt window will show
Input proprietor’s name and door number according to actual situation. There’s no specific
format.
Room number : Room number is made by the room proprietor lives. Room number has
four bit, for example, the proprietor lives in No. 1, 2/F; his/her room number is 0201. Room No.
would better not be written as 0001. The first two digits are not allowed to exceed 56, and the last
two digits are not allowed to exceed 08; Room shield card will not be able to shield this room No.
if room No. is more than 08. See V The Making of Shield Room Card in Making Management
Card number :Card number is formed automatically. The proprietor can change the card
number but he/she can’t use the number he/she used before.
Call method :Whether call method is to select the storey manually or automatically, and
selecting the storey manually means pressing the button of the elevator after swiping the card, and
selecting the storey automatically means lightening the button of the elevator selected directly
after swiping the card (selecting the storey automatically can only select two storey at maximum,
20
Elevator IC card operation manual
Elevator :Click on the right side to select elevator. If there is no elevator information,
you can add it in elevator information interface. Details please see VI elevator information.
Usable floor :The proprietor can set use floors by usable floor. Click on the left side to
select.
E-wallet can be used to store money the proprietor deposit on the card. Money can be
charged from E-wallet while you swipe card. The maximum money of every system operator can
be set. Details please see IV System subscriber foundation.
Note: ( 1 ) You cannot make new card if the card is not blank. So you should click
Refund amount can be changed, and there are decimals sometimes, that's because
there may be decimals while calculating the amount as per the frequency, during
which they it can be changed into the integral amount.
(3)Initialize card may delete the information of the card in database so please avoid
losing data. Please be careful wile you see the picture.
21
Elevator IC card operation manual
(4) If you can not make sure the card information, you can click to
see the card information which is on the information prompt frame right side of the interface.
If the proprietor lost the charging card, he/she can make up another card through this
interface.
Step two: Click left side of the main interface to open making up card for
Step three: Click to connect reader. Then the prompt window will show a
dialog to prompt you to select card and click button to open the interface which is
22
Elevator IC card operation manual
Inquire according to the situation provided by the proprietor and then select the lost card on
the result. Click button and back to re-issue card for lost card interface.
(1) You cannot make new card if the card is not blank. So you should click to
(2)Initialize card may delete the information of the card in database so please avoid losing
data.
(3)If you can not make sure the card information, you can click to see
the card information which is on the information prompt frame right side of the interface.
(9.3)Card charging
If the proprietor’s E-wallet needs charging, he/she can use this interface.
23
Elevator IC card operation manual
Step two: Click on the left side of the main interface to open card charging
interface.
Step three: Click to connect reader. Then the prompt window will show
Step four: Input the sum you want to charge at the place of charging.
Note: (1)If you cannot make sure the card information, you can click
to see the card information which is on the information prompt frame right side of the interface.
To make time period card which the proprietor use. This card only works in the
corresponding time interval, and becomes invalid overdue, which can be used in
monthly/annual package, with the amount charged in this time interval recorded.
Step one: Log on and enter the main interface.
Step two: Click on the left side of the main interface to open
Step three: Click to connect reader. Then the prompt window will
show system and the reader connect successfully , Password loaded successfully.
Step four: Input related information. The picture is as follow:
24
Elevator IC card operation manual
Input proprietor’s name and door number according to actual situation. There’s
no specific format.
Room number : Room number is made by the room proprietor lives. Room
number has four digits for example, the proprietor lives in No. 1, 2/F, his/her room
number is 0201. The first two digits are not allowed to exceed 56, and the last two
digits are not allowed to exceed 08; Room shield card will not be able to shield this
room No. if room No. is more than 08. See V The Making of Shield Room Card in
Making Management Card for the detailed making operation of shield room card.
Card number : Card number is formed automatically. The proprietor can
change the card number but he/she can’t use the number he/she used before.
Call method : Whether call method is to select the storey manually or
automatically, and selecting the storey manually means pressing the button of the
elevator after swiping the card, and selecting the storey automatically means
lightening the button of the elevator selected directly after swiping the card (selecting
the storey automatically can only select two storey at maximum, which can be
realized together with its corresponding hardware).
25
Elevator IC card operation manual
Usable floor :The proprietor can set use floors by usable floor. Click on the
left side to select.
Validity :The validity of the card can be used to set the use time of the card.
Usable time period : Usable time period can be used in twenty-four hours. If
the time before and after is the same, it shows that the card can be used the whole day.
Usable date :Usable date can be used to set functions according to week and
date. If you select, it shows that that day you can use the card, otherwise the card can
not be used on that day.
Electronic purse :Electronic purse is used to record the amount received in the
time interval card in these days.
Step five: Click the button to complete making time period card.
Note: (1) you can not make new card if the card is not blank. So you should click
(2)initialize card may delete the information of the card in database so make
sure to avoid lost of data.
( 3 ) if you can not make sure the card information, you can click
26
Elevator IC card operation manual
Step two: Click on the left side of the main interface to open
Step three: Click to connect reader. Then the prompt window will
show dialog to prompt you to select card and click button to open the
Inquire according to the situation provided by the proprietor and then select the
lost card on the result. Click button and back to re-issue card for lost card
interface.
Step four: Input new validity at the place of card validity. Input valid time at the
27
Elevator IC card operation manual
place of usable time period. Input valid week at the place of usable date.
(2)Initialize card may delete the information of the card in database so make sure to avoid
lost of data.
(3)If you can not make sure the card information, you can click to see
the card information which is on the information prompt frame right side of the interface.
Use this interface to prolong the use time of the proprietor time period card.
Step one: Log on and enter the main interface.
Step two: Click on the left side of the main interface to open
Step three: Click to connect reader. Then the prompt window will
show system and the reader connect successfully. Password loaded successfully.
Step four: Input period of validity at the place of period of validity. The
corresponding amount is filled in electronic purse.
28
Elevator IC card operation manual
10、Collecting Fingerprint
Step two: Click in the left side of main interface to open the
collector. The message connect fingerprint collector successfully will be shown if the
fingerprint collector is connected with the computer well; if not, the message will
prompt: please check the connection to the fingerprint readers.
Step four: Add information in the following interface,
29
Elevator IC card operation manual
and every information must be added, and there is no specification for filling owner
name and owner house number, and room No. must be 4-digit numbers, and the first
two digits mean the storey, and the last two digits mean room No., and available
elevator has the number of the storey available for the user, and available storey is the
storey that the user can reach .It is not necessary to input fingerprint No. that would be
generated by the system automatically, and 4 digits should be input as user passwords,
shown with asterisks.
fingerprint collector and then click for confirmation, and then the indicator on
fingerprint collector is red, and the data may be collected completely in 2s, after
successful input, the indication the fingerprint collector will turn into green from red,
during which your finger must be moved away( Note: If not, it will stay in this
status all the time, and next input can't be continued),then it will show
30
Elevator IC card operation manual
again and then click for confirmation, and the data may be collected completely in 2S,
after successful input, the indication the fingerprint collector will turn into green from
red, during which your finger must be moved away. And then it will show
again, and then click for confirmation, and the data may be collected completely in
2S, after successful input, the indication the fingerprint collector will turn into green
from red, during which your finger must be moved away. The message will show
successful collection and basic information of relevant fingerprint. (Note: this finger
must be placed for three times, and confirm if the collection of every fingerprint
is successful or not based on the color of collector indicator, and redo it again
after moving away.)
minute. (Note: During which any operation to the upper computer system is
prohibited.)
31
Elevator IC card operation manual
Then click and it will show a dialog, and then choose the information
of elevator no. to be sent in the elevator available, and choose the fingerprint no.
section to be sent and click the confirmation to export the data, during which there is
progress bar that will show the progress of sending the data, and it will dialog box for
completing the sending after the completion.
equipment, after the data in the data storage equipment is imported into the
corresponding elevator fingerprint system, it needs empty the data in the data storage
equipment while re-importing the information to other elevators, it is OK to click the
minute.
Note: during which any operation to the upper computer system is
prohibited.
Recommendation: the user is recommended to use his/her index finger,
secondly, middle finger and thumb, and the fourth finger and little finger are not
recommended.
(10.2)Changing Fingerprint
The purpose of changing fingerprint is to re-import new fingerprint when the user
is going to use another fingerprint.
Step I: Log on and enter into the main interface.
32
Elevator IC card operation manual
Step II: Click in the left side of the main interface to open the
the computer well; if not, the message will prompt: please check if fingerprint
collector is connected correctly or not.
Step IV: Look for the fingerprints to be changed in the interface (picture as
follow)
33
Elevator IC card operation manual
by the name, house number, room number, elevator and fingerprint number, and click
and then click the button , all the information will be filled
Step V: Click the button during which it will show the picture
34
Elevator IC card operation manual
then click for confirmation, and the data may be collected completely in 2S, after
successful input, the indication the fingerprint collector will turn into green from red,
during which your finger must be moved away. And then it will show
again ,and then click for confirmation, and the data may be collected completely in
2S, after successful input, the indication the fingerprint collector will turn into green
from red.
Note: this finger must be placed for three times to change the fingerprint,
and confirm if the collection of every fingerprint is successful or not based on the
color of collector indicator, and redo it again after moving away.
collector, which should be connected while exporting the data, and click to
show a dialog and then choose the information of elevator no. to be sent in the
elevator available, and choose the fingerprint no. section to be sent and click the
confirmation to export the data, during which there is progress bar that will show the
progress of sending the data, and it will dialog box for completing the sending after
the completion.
35
Elevator IC card operation manual
after the data in the data collector have been imported into the corresponding elevator
fingerprint system, it needs to empty the data in the data storage equipment while re-
importing the information of other elevators, it is OK to click the button
To make cards for managers. The manager can use this card to get to the specific
floor. This card is also an all-purpose card, without the limitation from the elevator
no., time and amount. This is usable as long as the system is normal. This card is
distributed to the property manager and special personnel. The storey authorization
can be selected randomly while making the card.
Step one: log on and enter the main interface.
Step two: lick management card making on the left side of the main interface.
Step three: click on the left side of the main interface to open
36
Elevator IC card operation manual
Step four: click to connect reader. Then the prompt window will
show system connect successfully with reader. Password loaded successfully.
Step five: set method for calling elevator and usable floor. Name of card holder.
Method for calling elevator can be used to assign operation mode of elevator.
Manual selecting floor after swiping card means that you should press the button to
select the desired floor after swiping card. Automatically selecting floor after swiping
card means that the button will automatically lit up after swiping card. Usually multi
authorized floors need manually selecting.
Usable floor is used to set the floor which the manager can use. Click on the
right to select.
The name of the card holder can be filled as the case may be, without
requirement on the format.
The period of validity of the card is used for setting service life of the card.
Available time interval is used for setting the valid time interval in 24 hours
every day for the card, and it is valid for the whole day if the front time and last time
are the same.
Usable date is used for setting the functions depending on whether the Sunday
card is valid or not, and it is usable date if chosen, vice versa.
Note: (1) you can not make new card if the card is not blank. So you should click
(2)initialize card may delete the information of the card in database so make
37
Elevator IC card operation manual
If the manager lost the management card, he/she can use this interface to re-
issue card.
Step one: Log on and enter the main interface.
Step three: Click to connect reader. Then the prompt window will
show system connect successfully with reader. Password loaded successfully. At the
same time prompt you to select card and click enter button to open the interface which
is used for selecting lost card as follow:
38
Elevator IC card operation manual
Inquire according to the situation provided by the proprietor and then select the
lost card on the result. Click enter button and back to the interface for re-issuing card.
Step four: Input new validity at the place of card validity
(2)initialize card may delete the information of the card in database so make
sure to avoid lost of data.
(3)if you can not make sure the card information, you can click
39
Elevator IC card operation manual
to see the card information which is on the information prompt frame right side of the
interface.
This card is used for closing the elevator available corresponding to room no. of
the storey in the unit forcibly. While it needs to close the elevator available
corresponding to room no. of the storey in the unit, it only needs to make forbidden
shield room card with room no. marked in the corresponding elevator no., and all the
cards can't be used for this elevator corresponding to this room no. after completing
the making, and it needs to re-open the shield room card to be initialized if to be
initialized.
It is used to make compulsory management card for manager. The manager can
use this card to mandatory
Step one: Log on and enter the main interface.
Step two: Click management card making on the left side of the main interface.
Step four: Click to connect reader. Then the prompt window will
40
Elevator IC card operation manual
card.
Note: (1) you can not make new card if the card is not blank. So you should click
(2)initialize card may delete the information of the card in database so make
sure to avoid lost of data.
( 3 ) if you can not make sure the card information, you can click
To make the corresponding time card of setting button for managers who can use
the card to set corresponding time for elevator button (extend the valid time for
selecting floor after swiping card.)
Step one: Log on and enter the main interface.
Step two: Click management card making on the left side of the main interface.
41
Elevator IC card operation manual
Step four: Click to connect reader. Then the prompt window will
show system connect successfully with reader. Password loaded successfully.
Step five: Time of assigned button.
Step six: Click to complete making time card for assigned button.
Note: (1) you can not make new card if the card is not blank. So you should click
(2)initialize card may delete the information of the card in database so make
sure to avoid lost of data.
( 3 ) if you can not make sure the card information, you can click
To make card of setting controller’s time for manager who can use the card to set
the current time of the elevator controller.
Step one: Log on and enter the main interface.
Step two: Click management card making on the left side of the main interface.
42
Elevator IC card operation manual
Step three: Click on the left side of the main interface to open the
Step four: Click to connect reader. Then the prompt window will
show system connect successfully with reader. Password loaded successfully.
Step five: assign the response time of elevator controller.
(2)initialize card may delete the information of the card in database so make
sure to avoid lost of data.
( 3 ) if you can not make sure the card information, you can click
To make card of reading proprietor data for manager who can use the card to
read the subscribers’ swiping card record.
43
Elevator IC card operation manual
Step three: Click on the left side of the main interface to open
Step four: Click to connect reader. Then the prompt window will
Step six: Click to complete making card for reading subscribers’ data.
Note: (1) you can not make new card if the card is not blank. So you should click
(2)initialize card may delete the information of the card in database so make
sure to avoid lost of data.
( 3 ) if you can not make sure the card information, you can click
44
Elevator IC card operation manual
To make the corresponding time card of visitor button for managers who can use
the card to set corresponding time for elevator button (extend the valid time for
selecting floor after swiping card.)
Step one: Log on and enter the main interface.
Step two: Click management card making on the left side of the main interface.
Step three: Click on the left side of the main interface to open
Step four: Click to connect reader. Then the prompt window will
To control elevator operation or forbidding. It can be used to control the elevator on different
days, different time periods or different floors. It indicates that this setup is invalid if 00:00
to 00:00 is written for the time interval available; while another time interval is filled,
during which (if forbidden time interval is not clicked) the storey chosen can be
operated directly without swiping the card; while forbidden time interval is clicked,
during which the storey chosen can't be operated even if the card is swiped.)
Step one: Log on and enter the main interface.
45
Elevator IC card operation manual
Step two: Click management card making on the left side of the main interface.
Step three: Click on the left side of the main interface to open
the interface for making time period card of setting elevator operation.
Step four: Click to connect reader. Then the prompt window will
Step six: Click to complete making time period card for setting elevator
operation.
46
Elevator IC card operation manual
Note: (1) Click firstly and make it become blank card and then make
a new card if the card is not blank and can't be used for making a new card.
(2) Initializing the card can eliminate corresponding information in the database,
and loss of data should be avoided.
shown in the place prompting the information in the right side of the interface if the
information of the card can't be confirmed.
This card is used for deleting the two passwords of the administrator in the
password keyboard. (This card has no meaning if there is no password keyboard
available in the equipment).
Step one: Logon and enter into the main interface.
Step two: Click making management card in the left side of the main interface
Step three: Click in the left side of the main interface to open
and make the card for deleting the password.
47
Elevator IC card operation manual
Step six: Click the button to complete the making of the card for
Note: (1) Click firstly and make it become blank card and then make
a new card if the card is not blank and can't be used for making a new card.
(2) Initializing the card can eliminate corresponding information in the database,
and loss of data should be avoided.
shown in the place prompting the information in the right side of the interface if the
information of the card can't be confirmed.
This card is used for controlling the special functions of opening/forbidding the
elevator in any storey, which can control the opening and forbidding of the elevator in
any time interval, or at any time in one day. During this time interval (if forbidden
time interval is not clicked), the storey chosen can be operated directly without
swiping the card; while forbidden time interval is clicked, during which the storey
chosen can't be operated even if the card is swiped.
Step one: Logon and enter into the main interface.
Step two: Click making management card in the left side of the main interface
48
Elevator IC card operation manual
Step three: Click in the left side of the main interface to open and
Step six: Click the button to complete the making of the card for setting
date management.
49
Elevator IC card operation manual
Note: (1) Click firstly and make it become blank card and then make
a new card if the card is not blank and can't be used for making a new card.
(2) Initializing the card can eliminate corresponding information in the database,
and loss of data should be avoided.
shown in the place prompting the information in the right side of the interface if the
information of the card can't be confirmed.
This card is the card for opening and closing the function of IC card used in one
elevator in one storey.
Step one: Logon and enter into the main interface.
Step two: Click making management card in the left side of the main interface
Step three: Click in the left side of the main interface to open
50
Elevator IC card operation manual
management card.
Note: (1) .Click firstly and make it become blank card and then
make a new card if the card is not blank and can't be used for making a new card.
(2).Initializing the card can eliminate corresponding information in the database,
and loss of data should be avoided.
shown in the place prompting the information in the right side of the interface if the
information of the card can't be confirmed.
This interface is to read the records on swiping the card (records on using the
elevator) via IC data collector.
Step one: Logon and enter into the main interface.
Step two: Click in the left side of the main interface to open and
read the interface for reading the records on swiping the card, as following figure:
51
Elevator IC card operation manual
card.
Note: Please check if the setting in communication port setting (under system
setting)is correct or not, or check if the line or connection of the communication is
correct or not if failure of communication is shown.
Long distance control refers to connect the elevator directly via the line, and
52
Elevator IC card operation manual
operate the elevator's controller directly to process the business, including the
processing shield card, setting response time of elevator button, setting response time
of controller and reading the records on swiping the card of the user in real time.
The card lost by the owner may be picked up by others, causing potential security
problems. Property management organization can prohibit the lost card quickly with
this function, eliminating potential security problem.
Step one: Logon and enter into the main interface.
Step two: Click long distance control in the left side of the main interface.
Step three: Click in the left side of the main interface to open the
interface for processing shield card.
53
Elevator IC card operation manual
You can inquire according to the status provided by the owner, and then check the
lost card in the inquiry results, and then click the button of enter and return to the
interface of adding your lost card.
Note: Please check if the setting in communication port setting (under system
setting) is correct or not, or check if the line or connection of the communication
is correct or not if failure of communication is shown.
Long distance setting designates response time of the button of the elevator.
Step one: Logon and enter into the main interface.
54
Elevator IC card operation manual
Step five: Click to set response time of the elevator and button.
Note: Please check if the setting in communication port setting (under
system setting) is correct or not, or check if the line or connection of the
communication is correct or not if failure of communication is shown.
Long distance setting designates the time for the controller of the elevator.
Step one: Logon and enter into main interface.
Step two: Click long distance control in the left side of the main interface.
Step three: Click in the left side of the main interface to open the
55
Elevator IC card operation manual
Step six: Click to set the time for the controller of the elevator.
Note: Please check if the setting in communication port setting (under system
setting) is correct or not, or check if the line or connection of the communication
is correct or not if failure of communication is shown.
Step three: Click in the left side of the main interface to open the
56
Elevator IC card operation manual
Note: Please check if the setting in communication port setting (under system
setting) is correct or not, or check if the line or connection of the communication
is correct or not if failure of communication is shown.
Monitor the records on swiping the card of the owner in real time
Step one: Logon and enter into the main interface.
57
Elevator IC card operation manual
Step two: Click long distance monitor in real time in the left side of the main
interface
Step three: Click in the left side of the main interface to open the
interface for long distance monitor, as follows:
Step four: Choose the elevator to monitor as the case may be, and have to choose
right elevator name and setting number.
58
Elevator IC card operation manual
Prohibit and initialize the function that the elevator uses IC card.
Step one: Logon and enter into the main interface.
Step two: Click elevator control in the left side of the main interface
Step three: Click in the left side of the main interface to open the
Step seven: The setting is successful if the display box displays successful
operation.
Note: Please check if the setting in communication port setting (under
system setting) is correct or not, or check if the line or connection of the
communication is correct or not if failure of communication is shown.
Long distance shield room is used for closing some elevators corresponding to
59
Elevator IC card operation manual
Step two: Click in the left side of the main interface to open
Long distance open storey is used for opening one elevator in one storey in long
distance.
Step one: Logon and enter into the main interface.
60
Elevator IC card operation manual
Step two: Click in the left side of the main interface to open the
13、Statistics inquiry
(13.1)charge statistics
61
Elevator IC card operation manual
Step three: Click on the left side of main interface to open the
Step Four: Conditions of inputting statistics. First select the subscriber, who needs
charge, you can select many people. And then assign the time period (above is the beginning time
62
Elevator IC card operation manual
Step three: Click on the left side of main interface to open the
Step four: Conditions of inputting statistics. Input the information by which you inquire.
For example, if you want to inquire according to card number, you can just input card number. If
you want to inquire according to card number and user name, you can input the card number and
user name.
63
Elevator IC card operation manual
Inquire to the records on swiping the card by the owner collected by long distance
monitor.
Step one: Logon and enter into the main interface.
Step two: Click statistics inquiry in the left side of the main interface
Step three: Click in the left side of the main interface to open
the interface for the inquiry of records on swiping the card, as following figure:
Step four: Input statistics condition. You can inquire by elevator or card number,
or both, and inquire by the date on swiping the card without inputting the elevator and
card number. You can input both the elevator and card number or one of them, and the
date starting swiping the card and the date ending swiping the card must be input.
64
Elevator IC card operation manual
Note: (1) You can click and input the records on swiping the card
Step three: Click in the left side of the main interface to open
Step four: Input statistics condition, and input the contents by which you inquire,
and you can inquire by fingerprint no., room no, elevator, name and house number.
And input corresponding owner name and corresponding room number if you inquire
by name and room number.
65
Elevator IC card operation manual
Note: (1) You can click and input the records on swiping the card
1 . Manager card: Manager Card, which refers to all-pass card, can be made by
administrator through software of host computer. The card has no difference in elevator No.
setting, time limitation and monetary limitation. So long as the system keeps running state, the
card can be used. Generally, the card is issued to property management personnel and some
special personnel, and the floor authority can be selected arbitrarily according to the need during
card making process.
2. Mandatory management card: Mandatory management card, which is made for user
administrators, can be made through software of host computer. Use: It is used to close the
elevator used by users of some corresponding floor rooms forcibly. When the elevator used by
users of some corresponding floor rooms is required to be closed, the card maker just needs to fill
in the room No. of the user to be forbidden for taking elevator at the registration information of
corresponding elevator No. when making the mandatory management card, swipe the card in the
elevator after the card is made, then users of all the cards of the room No. are unable to take the
elevator, if they want to enable all the cards, then a mandatory management card for enabling shall
be made to enable the room No.
3. Card for setting button response time: The card is a card used to set the effective delay
time during which the elevator buttons can be lighted up by pressing after the user swipes his/her
card. After the card is made, it can only be valid after being swiped at the site controller and the
set delay time can be changed according to the need.
4. Card for setting controller clock: The card is used to adjust the time of the master
controller, when the time of the master controller is incorrect, the card can be made for adjustment
of time. The card can only be used once and it can not be used for the second time.
5. Card for setting time of visitor button: The card is used in system with visitor intercom
linkage function and it is a card used for setting the delay time when the elevator button for visitor
is available. Its making method is same with that of card for setting button response time.
6. Card for reading user data: It can be used to read the card-swiping record stored in the
master controller. One card can read 84 data records at most and these records include start record
and end record. After the card is made, swipe the card, read the information in the card on the card
writer and then the corresponding card-swiping information can be obtained.
66
Elevator IC card operation manual
7. New card issuance: Cards made in the column are general user cards, when the hardware
is set to be chargeable, the amount of money in the card shall be deducted with the card-swiping
times and these cards belong to cards which used to pay elevator fee by card swiping.
8. Card reissue for lost card: That is to make a new card with the same card number with
the lost general user card to substitute for the original card, after the new card is swiped in the
corresponding elevator, the original card will be invalid and the functions of the new card are
same with those of the general user card.
9. Time period card: The card, which is valid only in corresponding time period, will
become invalid after the specified time limit, and it can be used in monthly pay service and annual
pay service. It can be used in the system in conjunction with general user cards.
10. Reissue of time period card: That is to make a new time period card with the same card
number with the lost time period card to substitute for the original time period card, after the new
card is swiped in the corresponding elevator, the original card will be invalid.
11. Card for setting running time period of elevator: Management card which is specially
made to prohibit the use of elevator, unlock use of elevator and unlock elevator to cardholders on
some floors within a certain time period on special occasions. The card can be made in the host
computer for users according to the need.
12. The card for setting date management: in spcial occasion, this card is used
for controlling the special functions of opening/forbidding the elevator in any storey,
which can control the opening and forbidding of the elevator in any time interval, or
at any time in one day. ( During this time interval (if forbidden time interval is not
clicked), the storey chosen can be operated directly without swiping the card; while
forbidden time interval is clicked, during which the storey chosen can't be operated
even if the card is swiped.)
13. Layered management card: this card is the card for opening and closing
the function of IC card used in one elevator in one storey.
1.If there is no response of the card reader, cut off the power supply and then
67
Elevator IC card operation manual
reinsert the card reader and energizate to operate the card reader. Then the card reader
will give a long and a short buzzes and the red indicator is always on.
interface.
Note 1:
give one buzz, which means that the system enters operation state and you should
swipe card to use elevator. While swiping card, the buzz gives two buzzes, which
means the system enters open state and you can use elevator without card. Note:
please do not initialize the card through software of host computer.
4. Card for increase or decrease elevator No. : While debugging the system, it
used for debug the device No. You swipe card each time, the device No. will increase
or decrease. While making user card, the elevator serial No. must be the same with
device No. Function: to avoid person with card enter elevator randomly. If you
separate the elevator No. , people with different elevator No. card can not enter other
elevator. Note: this card can not be initialized through software of host computer.
5. If you want to unload this system, you should make a backup of db document
file. For example, you install the system in C:\Program Files, then the catalog of db
68
Elevator IC card operation manual
69