Professional Documents
Culture Documents
Standardization
Utilities Equipments Proposed revisions to this Standard shall be submitted to the CONTEC -
Authoring Subcommittee, indicating the alphanumeric identification and revision
of the Standard, the section, subsection and enumerate to be revised, the
proposed text, and technical/economic justification for revision. The proposals
are evaluated during the work for alteration of this Standard.
Introduction
PETROBRAS Technical Standards are prepared by Working Groups - WG
(consisting specialized of Technical Collaborators from Company and its Subsidiaries), are
commented by Company Units and its Subsidiaries, are approved by the Authoring Subcommittees -
SCs (consisting of technicians from the same specialty, representing the various Company Units and
its Subsidiaries), and ratified by the Executive Nucleus (consisting of representatives of the Company
Units and its Subsidiaries). A PETROBRAS Technical Standard is subject to revision at any time by its
Authoring Subcommittee and shall be reviewed every 5 years to be revalidated, revised or cancelled.
PETROBRAS Technical Standards are prepared in accordance with PETROBRAS Technical
Standard N-1. For complete information about PETROBRAS Technical Standards see PETROBRAS
Technical Standards Catalog.
.
PROPERTY OF PETROBRAS 15 pages, 1 form, Index of Revisions and WG
-PUBLIC-
Foreword
This Standard is the English version (issued in 08/2012) of PETROBRAS N-2249 REV. D 01/2012,
including its Amendment - 05/2012). In case of doubt, the Portuguese version, which is the valid
document for all intents and purposes, shall be used.
1 Scope
1.1 This Standard standardizes the Data Sheet for Water-tube Boiler to be used in projects for
PETROBRAS.
2 Normative References
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document applies.
NOTE For documents referred in this Standard and for which only the Portuguese version is
available, the PETROBRAS department that uses this Standard should be consulted for any
information required for the specific application.
3 General Conditions
3.1 The Data Sheet is intended to record the buyer's requirements and design details of the supplier,
and once completed, it shall be a permanent document of the equipment.
NOTE In addition to the Data Sheet, the designer shall provide the Performance Data Sheet at the
end of the Project and, after assembly, the efficiency of the boiler shall be evaluated.
3.2 The form of the Data Sheet in is standardized in A4 format, in accordance with Annex A.
3.3 To fill in the header and footer of the Data Sheet, abide to PETROBRAS N-381.
3.4 The applicable Annex PETROBRAS N-381 shall be used for continuation of any item that does
not fit in Annex A of this Standard.
2
-PUBLIC-
3.5 Identification of the boiler shall comply with PETROBRAS N-1521, and be written in the header
field referring to the name of the equipment (water-tube boiler), in the right corner.
3.6 ABNT NBR 11096 shall be followed in order to fill out the Data Sheet.
3.7 In filling out the Data Sheet, the following requirements shall be followed:
a) complete only the applicable fields, eliminating, with a horizontal line, the fields that are
not applicable to the specific project;
b) in the empty lines, add any additional data on the specific project.
3.8 This Data Sheet shall be reproduced for its routine use.
3
-PUBLIC-
4
-PUBLIC-
5
-PUBLIC-
6
-PUBLIC-
7
-PUBLIC-
8
-PUBLIC-
9
-PUBLIC-
10
-PUBLIC-
11
-PUBLIC-
12
-PUBLIC-
13
-PUBLIC-
14
-PUBLIC-
15
-PÚBLICO-
INDEX OF REVISIONS
REV. A
There is no index of revisions.
REV. B
Affected Parts Description of Alteration
Revalidation
REV. C
Affected Parts Description of Alteration
Revalidation
REV. D
Affected Parts Description of Alteration
All Revised
IR 1/1