Professional Documents
Culture Documents
6.1 60 grade Deformed Bars of 415 MPa (60000 psi) kg 250.00 82.70 20,675.00
7.0 Brick Work - -
SI. No. Description of items Unit Quantity Unit Rate Amount (taka)
(Taka)
7.1 10" (250 mm)Exposed brick works (for exterior wall without cum 21.25 104,536.40
outside plaster) with special quality sorted out first class
bricks, very carefully laid in cement sand (F.M. 1.2) mortar
(1:4)) in superstructure with uniform width and depth joints,
true to vertical and horizontal lines including raking out joints
scaffolding, soaking the bricks at least for 24 hours before use,
washing and screening of sand. Curing at least for 7 days and
4,920.18
high class flush pointing with cement sand (F.M. 1.2) mortar
(1:1) including cost of water, electricity and other charges etc
all complete and accepted by the Engineer.
7.2 5" (125 mm) brick works with first class bricks in cement sqm 234.45 175,933.93
sand (F.M. 1.2) mortar (1:4) and making bond with connected
walls including necessary scaffolding, raking out joints,
cleaning and soaking the bricks for at least 24 hours before use
and washing of sand curing at least for 7 days in all floors 750.40
including cost of water, electricity and other charges etc. all
complete and accepted by the Engineer.
9.0 38 mm thick artificial patent stone (1:2:4) flooring with sqm 156.38
cement, best quality coarse sand (50% quantity of Sylhet sand
or coarse sand of equivalent F.M. 2.2 and 50% best local sand
of FM 1.2) and 12 mm down well graded Brick chips, laying
the concrete in alternate panels, compacting and finishing the
top with neat cement and curing at least 7 days in all floors 311.71 48,744.30
including cost of water, electricity and other charges etc. all
complete and accepted by the Engineer.
Supplying, fitting and fixing Plain Sheet Door made with 1.5” sqm 6.69
x 1.5” x 3/4”, 5mm angle outer frame, inner member 3/4” x
5mm F.I. bar, cladding with 22 BWG M.S. sheet, hinged with 2,700.00 18,066.91
2” x 2” x ¼” M.S. angle Chowkat.
kg
Fabrication,supply of frame with pre-engineered L-section
(50mmX50mmX4mm and 40mmX40mmX3mm) with M.S.
Angle for Rafter including painting as per drawing, design & 1050.00 85.00 89250.00
direction of the Engineer in charge.(ASTM A 572M Grade
345 Type 1, Fu = 45.0 kN/cm2)
10.2 W.C SUITE: Supply, fitting and fixing of glazed vitreous China low Each 1.00 1970.00 1970.00
level wash down W.C. (European Type) of approve size. The W.C
shall have built-in ''P'' or ''S'' type trap. The unit shall comprise of
vitreous China low level flushing cistern of approved color-having
approve. -a 9 (nine) lit, capacity with reversible type side inlet,
overflow and lever. The cistern shall be complete with float valve,
plastic syphon, PVC flush pipe with bends and brass coupling;
cistern supports The w.c. shall be complete with bends and brass
couplings, cistern supports the w.c. shall be completed with heavy
duty plastic seat cover of approved color, PVC outlet connector. All
necessary accessories such as 12 mm dia C.P. angle valve, 12 mm dia
PVC flexible hose with C.P. brass coupled and fixed. The complete
installation work of the unit includes preparing the base with cement
concrete 1:2:4 and anchoring with the soil same connect with the
pipes, interlocking with water supply system, fixing of cistern flush
pipe etc. complete in all respect. All necessary cutting of floors/walls
and making food of the same shall be done. All required consumable
needed to complete the shall be supplied and fixed. The unit shall be
installed at location shown in the drawing and as per direction of the
CMT. The product shall be of Code No. 104/104A & 401 of BISF
Standard Grade) set. (Excluding low down)
10.3 Supplying, fitting and fixing European type glazed porcelain Each 1.00 2216.25 2216.25
low-down, capacity 10 liter, 490 x 190 x 350 mm in size,
approximately 14 kg by weight, on walls by screws and F.I.
bar clamps, rowel plugs, making holes wherever required and
mending good the damages and fitting, fixing finishing etc.
complete with all necessary fittings and connection approved
and accepted by the Engineer.
SI. No. Description of items Unit Quantity Unit Rate Amount (taka)
(Taka)
10.4 WASHBASIN: Supply, fitting and fixing of glazed vitreous Each 1.00 2462.50 2462.50
China wash basin of approved size, color and model, The unit
shall have a well-contoured bowl to reduce splashing and shall
have one tap hole at the centre. The unit shall be complete
with 13 mm size C.P. waste fittings with overflow slot and
china plug 32 mm C.P. bottle trap with 75 mm water seal and
adjustable inlet pope or brass coupling. All necessary
accessories such as 32 mm dia PVC waste pipe, 13 mm dia
C.P Angle valve, heavy duty HCI fixing brackets etc. Shall be
supplied and fixed. The installation work shall include all
roughing in works, fixing and concealing of waste pipe,
hooking up with the water supply system, connecting the
waste line with the main waste water pipe, etc, complete in all
respect. Necessary accessories, hardwires, consumables need
for completion of the work shall be supplied and the works
shall be done as direction of the CMT.
Without Mixture
10.5 SHOWER COMPLEX: Supply fitting & fixing shower Each 1.00 2708.73 2708.73
complex comprising of 12 mm dia C.P Concealed stop cock
( Hot/ Cold) with flange, 12mm dia C.P bib tap, 50 mm dia
shower rose with 12 mm dia C.P arms and flange with
necessary accessories fittings in and completed in all respect
as per direction of the CMT/ Consultant.
10.6 MIRROR: Supply, fitting and fixing of 5mm thick chromium Each 2.00 295.50 591.00
back coated polished mirror made of high quality drawn sheet
glass of size 600mm x 450mm. The mirror shall be fixed on
the wall backed with nylon or any waterproof sheet. The
mirror shall be fixed with fixing adhesive tapes as per drawing
and direction of the CMT.
10.7 GLASS SHELF: Supply, fitting and fixing of supper quality Each 2.00 369.38 738.76
(600mmx125mm) plate glass shelf of 5mm thickness with
fancy C.P. brackets, screw and frames including making holes
in walls and mending good the damages etc, all complete as
per direction of the CMT.
10.8 SOAP DISPENSER: Supply, fitting and fixing of wall Each 4.00 1147.75 4591.00
mounted stainless steel soap dispenser of approved type,
model and size. All necessary gltnilar to PS 14 with GLS-
60w,
10.9 Towel Rail: Supply, fitting and fixing of CP (best quality Each 2.00 374.30 748.60
Nazma/Sharif or approved equivalent ).Towel rail complete
set 600mm long 19mm dia.
SI. No. Description of items Unit Quantity Unit Rate Amount (taka)
(Taka)
10.1 Toilet Paper Holder: Supply, fitting and fixing of wall Each 2.00 265.95 531.90
mounted toilet paper holder of approved type and model.
10.1 C.P. Bib Cock: Supply, fitting and fixing of 12mm size C.P. Each 4.00 807.70 3230.80
Bib cock nazma or sharif or approved equivalent complete
with fixing accessories.
10.12 C.P. Stop Cock: Supply, fitting and fixing of 12mm size C.P. 4.00 887.40 3549.60
Stop cock nazma or sharif or approved equivalent complete
with fixing accessories.
10.13 CP pillar cock: Supplying, fitting and fixing medium best Each 2.00 714.13 1428.26
quality CP pillar cock etc. complete approved and accepted by
the Engineer. 12 mm CP special heavy duty pillar cock.
10.14 Supplying, fitting and fixing 12 mm dia, 450 mm long Plastic Each 1.00 54.18 54.18
flexible lead (connection) pipe approved and accepted by the
Engineer.
10.15 Supplying, fitting and fixing 12 mm dia, 600 mm long Plastic Each 3.00 73.88 221.64
flexible lead (connection) pipe approved and accepted by the
Engineer.
10.16 Supply and installation of 2000 litter capacity Gazi water Each 1.00 17730.00 17730.00
tank including necessary hardware, fittings and consumables
etc. all complete approved and accepted by the Engineer.
10.17 G.I PIPES: Supply, fitting, fixing and testing of G.l. pipes of
schedule 40(s) of following nominal diameter with all
necessary fittings and accessories etc. sockets, bends, elbows,
tees, reducers, unions, jam nuts, flanges etc. The pipes shall be
of welded type and suitable to withstand a test pressure of 250
psi. pipes up to 75mm dia shall be of treated end type and pipe
of 87mm dia or larger shall be of flanged end type. The piping
work includes supply and fixing of hanger, holder bolts,
brackets, and clamps supports gaskets, sealant, etc. It also
includes concealing the pipes, within walls/floor, or laying
underground (wherever necessary). All pipes shall be
thoroughly checked and cleaned before installation. All
necessary cutting and making holes and mending the damages
in the walls/floor/calling shall be done up to the satisfactory of
the Engineer-in-Charge. Sleeves of two size larger diameter
shall be used where pipes run through walls/floors. All
consumable required to complete the work shall be supplied
fixed at no extra cost.
16.2 Supply & installation of 13A, 3-pin, 250V, combined each 3.00 738.40 2215.20
switched socket (concealed type) suitable for 3-pin plug of
approved model from M.K(Malaysia/Kallas (PAK) or its
equivalent from countries like USA, UK, CANADA etc
including the box, cover plate with necessary galvanized
machine screws, earthing block complete with necessary
connections as per drawing, specifications and direction of the
Engineer-in-charge
SI. No. Description of items Unit Quantity Unit Rate Amount (taka)
(Taka)
17 DISTRIBUTION BOARDS:Supply & installation ,testing &
commissioning of imported totally insulated distribution
boards from reported manufacturers of USA, UK ,CANADA
housing the following rated circuit breakers, ON-OFF switch,
contractors, and busbar and all other accessories as per
technical specifications and drawing. The distribution board
shall be of suitable dimensions so as to accommodate the
circuit breakers and busbar with insulated shroud with
sufficient spacing including internal connection cable in the
board and other materials shall have hanged type lockers ,
circuit directory shall be suitable for concealed/surface
mounted type having PVC cable gland/grommets of
appropriate sizes shall have knockout for conduit entry and
exist, a suitable size cupper plate earthing block must be
provided inside the box.The rate should be quoted materials
for thios item and cost shall include the necessary clearing and
necessary civil work. All S/B board are made by LEGEND
company.
17.1 MDB
Incoming : 1x63A ATP MCCB/D.P
Outgoing : .5x32 ASP MCB
100ATP+N+PE insulated Busbar, Size 12"X14" set 1.00 8372.50 8372.50
18 FAN:Supply & installation of 56 inch sweep ceiling fan brand each 12.00 3250.50 39006.00
BRB/GEC/National down rod (if required) , and all other
accessories as per drawing, specifications and direction of the
Engineer-in-charge.
18.1 Supply & installation of concealed type fan hook of ½ inch Each 12.00 49.25 591.00
40 grade plain bar with box(size:4 & ½ dia & depth 2 inch)
made of 16SWG sheet steel box of approved quality
everything complete as per drawing, specifications and
direction of the Engineer-in-charge
In word:- Ten lac ninety thousand two hundrad eighty four taka & eighty one paisa only
1373.22
131.22
5000
487.38
706.1
98.41
1550
290.55
70
350
86.201096
750 5214.8493
2522.72 720
2600 180
1682.6175 335.25909
250 146.82418
5629.0835
72
1829.20
220 2008.9117
0.00
3 2500 2465.00
2 4000 3944.00
5 2500 2465.00
5 2500 2465.00
5 4000 3944.00
5 400 394.40
5 400 394.40
10 1200 1183.20
5 400 394.40
5 400 394.40
7 1100 1084.60
12 900 887.40
5 1500 1479.00
5 100 98.60
5 100 98.60
1 23500 23171.00
0.00
0 400 394.40
40 380 374.68
12 350 345.10
0.00
120 400 394.40
20 100 98.60
0.00
0.00
2 1000 986.00
0.00
0.00
300 30 29.58
700 25 24.65
0.00
1200 25 24.65
200 47 46.34
150 73 71.98
100 130 128.18
0.00
100 20 19.72
48 380 374.68
0.00
0.00
6 100 98.60
5 100 98.60
4 150 147.90
8 150 147.90
5 50 49.30
4 50 49.30
8 60 59.16
0.00
77 40 39.44
9 350 345.10
6 400 394.40
0.00
0.00
0.00
0.00
1 20500 20603.08
28 3600 3549.60
28 100 98.60
SCHEDULE OF RATES FOR CONSTRUCTION OF GENERATOR BUILDING AT
AKKHAN-CRP, CHITTAGONG.
SI. Description of items Unit Quantity Unit Rate (Taka) Amount (taka)
No. Note: All items of works shall be
executed as per specification,
schedule of works, design,
drawing, direction and instruction
of the Engineer-in
charge/Consultant.
a) Earthwork in excavation in
foundation trenches up to 1.5 m cum 25.50 137.78 3,512.83
depth and maximum 10 m lead: in
soft clayey soil / loose sand / silt
2 Sand filling in foundation
trenches and plinth with sand
having F.M. 0.5 to 0.8 in 150mm
layers including leveling, watering
and compaction to achieve
minimum dry density of 90% with
optimum moisture content
(Modified proctor test) by
ramming each layer up to finished cum 48.16 511.75 24,645.14
level as per design supplied by the
design office only etc. all
complete and accepted by the
Engineer.
engineer-in-charges.
5 Mass concrete (1:3:6) in
direction of engineer-in-charge.
a) Mass concrete in floor (1:3:6) cum 4.25 6,052.38 25,718.32
with brick chips & local sand of
4.2 Lintels, Railing, Drop walls, Sunshade, False ceiling -
F.M. 1.2
Concrete (1:2:4) cum 0.85 6,900.0 5,864.0
5.0 Form work/shuttering, prop and -
necessary support etc.(steel)
5.2 Lintels, Railing, Drop walls, Sunsha sqm 32.527881 350.0 11,384.8
8.0 Reinforcement in R.C.C Steel
reinforcement works in RCC
works providing deformed and
plain bars of any size
manufactured from billets having
min. yield strength as specified
below unless other wise specified,
cleaning the steel surface, cutting
the bars in required length, making
the bars as per shape and size,
placing the bars in position,
binding & fixing the bars in
position by using 22 BWG G.I
- -
binding wire providing necessary
blocks, chair, hangers, spacers etc.
(No payment shall be made for
overweight and wastage, payment
shall be made as per approved bar
bending schedule),all works
complete in all respect in all
floors. (BSRM)
17 DISTRIBUTION
BOARDS:Supply & installation
,testing & commissioning of
imported totally insulated
distribution boards from reported
manufacturers of USA, UK
,CANADA housing the following
rated circuit breakers, ON-OFF
switch, contractors, and busbar
and all other accessories as per
technical specifications and
drawing. The distribution board
shall be of suitable dimensions so
as to accommodate the circuit
breakers and busbar with insulated
shroud with sufficient spacing
including internal connection
cable in the board and other
materials shall have hanged type
lockers , circuit directory shall be
suitable for concealed/surface
mounted type having PVC cable
gland/grommets of appropriate
sizes shall have knockout for
conduit entry and exist, a suitable
size cupper plate earthing block
must be provided inside the
box.The rate should be quoted
materials for thios item and cost
shall include the necessary
clearing and necessary civil work.
17.1 All
SDBS/B board are made by
LEGEND company.
Incoming : 1x32A ATP MCCB/D.P
Outgoing : 3x16 ASP MCB
63ASP+N+PE insulated Busbar, Si set 1.00 4000.00 4000.00
18 FAN:Supply & installation of 56 each 3.00 3549.60 10648.80
inch sweep ceiling fan brand
BRB/GEC/National down rod (if
required) , and all other
accessories as per drawing,
specifications and direction of the
Engineer-in-charge.
In word:-Ten lacs tweenty six thousand two hundrad twelve point fifty eight taka only
900
131.22
1700
487.38
900
98.41
600
290.55
0
150 5764.17
30
350
86.2011
1850 5214.849
3000 180
650 335.2591
5 127549
81 5629.084
70
220 2008.912
5 2500
700 25
1200 25
200 47
48 380
6 100
5 100
4 150
5 50
4 50
8 60
77 40
9 350
6 400
1 20500
28 3600
28 100
SCHEDULE OF RATES FOR CONSTRUCTION OF SEMI PERMANENT PATIENT ACCOMMODATIO
SI. No. BUILDING
Description AT AKKHAN-CRP, CHITTAGONG.
of items Unit Quantity Unit Rate
Note: All items of works shall be executed as per specification, (Taka)
schedule of works, design, drawing, direction and instruction of
the Engineer-in charge/Consultant.
1 Earth work in excavation in all kinds of soil for foundation
trenches including. layout, providing center lines, local bench-
mark pillars, leveling, ramming and preparing the base, fixing
bamboo spikes and marking layout with chalk powder,
providing necessary tools and plants, protecting and maintaining
the trench dry etc., stacking, cleaning the excavated earth at a
safe distance out of the area enclosed by the layout etc. all
complete and accepted by the Engineer, subject to submit
method statement of carrying out excavation work to the
Engineer for approval. However, Engineer’s approval shall not
relieve the contractor of his responsibilities and obligations
under the contract.
8.1 60 grade Deformed Bars of 415 MPa (60000 psi) kg 450.00 90.51
9.0 Brick Work -
9.1 10" (250 mm)Exposed brick works (for exterior wall without cum 21.25
outside plaster) with special quality sorted out first class bricks,
very carefully laid in cement sand (F.M. 1.2) mortar (1:4)) in
superstructure with uniform width and depth joints, true to
vertical and horizontal lines including raking out joints
scaffolding, soaking the bricks at least for 24 hours before use,
washing and screening of sand. Curing at least for 7 days and
high class flush pointing with cement sand (F.M. 1.2) mortar 5,475.59
(1:1) including cost of water, electricity and other charges etc all
complete and accepted by the Engineer.
9.3 5" (125 mm) brick works with first class bricks in cement sand sqm 234.45
(F.M. 1.2) mortar (1:4) and making bond with connected walls
including necessary scaffolding, raking out joints, cleaning and
soaking the bricks for at least 24 hours before use and washing
of sand curing at least for 7 days in all floors including cost of 756.00
water, electricity and other charges etc. all complete and
accepted by the Engineer.
10.3 38 mm thick artificial patent stone (1:2:4) flooring with sqm 156.38
cement, best quality coarse sand (50% quantity of Sylhet sand or
coarse sand of equivalent F.M. 2.2 and 50% best local sand of
FM 1.2) and 12 mm down well graded Brick chips, laying the
concrete in alternate panels, compacting and finishing the top
with neat cement and curing at least 7 days in all floors
including cost of water, electricity and other charges etc. all
complete and accepted by the Engineer. 352.02
11.2 Synthetic Enamel Paint: Two coats of synthetic enamel paint sqm 23.23
(Berger or approved equivalent) of approved color to the
Exposed steel surface (non G.I) over a coat of Red Oxide Primer 154.17
necessary surface cleaning and scaffolding, etc all works
complete.
12.2 Chapalish wood with 3 coats of french polishing over a coat of cum 0.14
priming. ###
Supplying, fitting and fixing Plain Sheet Door made with 1.5” sqm 6.51
x 1.5” x 3/4”, 5mm angle outer frame, inner member 3/4” x
5mm F.I. bar, cladding with 22 BWG M.S. sheet, hinged with 2,700.00
2” x 2” x ¼” M.S. angle Chowkat.
Supplying, fitting and fixing 0.42 mm thick corrugated sqm
galvanized iron sheet (Bangladesh made) having min weight
63-65 kg per bundle (2'-6" width 8'-00 " long) fitted and fixed
on M.S. sections with 'J' hook or wooden purlin with screws,
limpet washers and putty etc. all complete and accepted by the 170.00 540.00
Engineer.(** Supply 'j' hook and other fitting Labour Charge)
13.0 M.S. Window Grills: Supplying, Fitting and fixing of sqm 21.00
Window with Z bar and glasses & Grill of any design made of
M.S flat bar 3/4" of 5mm thickness supported integrally by built
and connect to floor by 4" flat bar anchored to floor concrete
with at least 4 nos of screw, intermediate runner welded to
balustrade exactly with circular finishing, fabrication welding,
2,109.36
applying to coats of synthetic enamel paint, (Berger, approved
color) over a coat of anticorrosive paint (Berger) including
hardware scaffolding etc. All complete as per design and
drawing.
10.4 WASHBASIN: Supply, fitting and fixing of glazed vitreous Each 1.00 2500.00
China wash basin of approved size, color and model, The unit
shall have a well-contoured bowl to reduce splashing and shall
have one tap hole at the centre. The unit shall be complete with
13 mm size C.P. waste fittings with overflow slot and china plug
32 mm C.P. bottle trap with 75 mm water seal and adjustable
inlet pope or brass coupling. All necessary accessories such as
32 mm dia PVC waste pipe, 13 mm dia C.P Angle valve, heavy
duty HCI fixing brackets etc. Shall be supplied and fixed. The
installation work shall include all roughing in works, fixing and
concealing of waste pipe, hooking up with the water supply
system, connecting the waste line with the main waste water
pipe, etc, complete in all respect. Necessary accessories,
hardwires, consumables need for completion of the work shall
be supplied and the works shall be done as direction of the
CMT. Without Mixture
10.5 SHOWER COMPLEX: Supply fitting & fixing shower Each 1.00 3944.00
complex comprising of 12 mm dia C.P Concealed stop cock
( Hot/ Cold) with flange, 12mm dia C.P bib tap, 50 mm dia
shower rose with 12 mm dia C.P arms and flange with necessary
accessories fittings in and completed in all respect as per
direction of the CMT/ Consultant.
10.6 MIRROR: Supply, fitting and fixing of 5mm thick chromium Each 2.00 394.40
back coated polished mirror made of high quality drawn sheet
glass of size 600mm x 450mm. The mirror shall be fixed on the
wall backed with nylon or any waterproof sheet. The mirror
shall be fixed with fixing adhesive tapes as per drawing and
direction of the CMT.
10.7 GLASS SHELF: Supply, fitting and fixing of supper quality Each 2.00 394.40
(600mmx125mm) plate glass shelf of 5mm thickness with fancy
C.P. brackets, screw and frames including making holes in walls
and mending good the damages etc, all complete as per direction
of the CMT.
10.8 SOAP DISPENSER: Supply, fitting and fixing of wall mounted Each 2.00 1183.20
stainless steel soap dispenser of approved type, model and size.
All necessary gltnilar to PS 14 with GLS- 60w,
10.9 Towel Rail: Supply, fitting and fixing of CP (best quality Each 2.00 394.40
Nazma/Sharif or approved equivalent ).Towel rail complete set
600mm long 19mm dia.
10.1 Toilet Paper Holder: Supply, fitting and fixing of wall Each 2.00 394.40
mounted toilet paper holder of approved type and model.
10.1 C.P. Bib Cock: Supply, fitting and fixing of 12mm size C.P. Each 4.00 1084.60
Bib cock nazma or sharif or approved equivalent complete with
fixing accessories.
10.12 C.P. Stop Cock: Supply, fitting and fixing of 12mm size C.P. 4.00 887.40
Stop cock nazma or sharif or approved equivalent complete with
fixing accessories.
10.13 CP pillar cock: Supplying, fitting and fixing medium best Each 2.00 1479.00
quality CP pillar cock etc. complete approved and accepted by
the Engineer. 12 mm CP special heavy duty pillar cock.
10.14 Supplying, fitting and fixing 12 mm dia, 450 mm long Plastic Each 1.00 98.60
flexible lead (connection) pipe approved and accepted by the
Engineer.
10.15 Supplying, fitting and fixing 12 mm dia, 600 mm long Plastic Each 3.00 98.60
flexible lead (connection) pipe approved and accepted by the
Engineer.
10.16 Supply and installation of 2000 litter capacity Gazi water tank Each 1.00 23171.00
including necessary hardware, fittings and consumables etc. all
complete approved and accepted by the Engineer.
10.17 G.I PIPES: Supply, fitting, fixing and testing of G.l. pipes of
schedule 40(s) of following nominal diameter with all necessary
fittings and accessories etc. sockets, bends, elbows, tees,
reducers, unions, jam nuts, flanges etc. The pipes shall be of
welded type and suitable to withstand a test pressure of 250 psi.
pipes up to 75mm dia shall be of treated end type and pipe of
87mm dia or larger shall be of flanged end type. The piping
work includes supply and fixing of hanger, holder bolts,
brackets, and clamps supports gaskets, sealant, etc. It also
includes concealing the pipes, within walls/floor, or laying
underground (wherever necessary). All pipes shall be
thoroughly checked and cleaned before installation. All
necessary cutting and making holes and mending the damages in
the walls/floor/calling shall be done up to the satisfactory of the
Engineer-in-Charge. Sleeves of two size larger diameter shall be
used where pipes run through walls/floors. All consumable
required to complete the work shall be supplied fixed at no extra
cost.
16.2 Supply & installation of 13A, 3-pin, 250V, combined switched each 3.00 394.40
socket (concealed type) suitable for 3-pin plug of approved
model from M.K(Malaysia/Kallas (PAK) or its equivalent from
countries like USA, UK, CANADA etc including the box, cover
plate with necessary galvanized machine screws, earthing block
complete with necessary connections as per drawing,
specifications and direction of the Engineer-in-charge
17.1 MDB
Incoming : 1x63A ATP MCCB/D.P
Outgoing : .5x32 ASP MCB
100ATP+N+PE insulated Busbar, Size 12"X14" set 1.00 15000.00
18 FAN:Supply & installation of 56 inch sweep ceiling fan brand each 15.00 3549.60
BRB/GEC/National down rod (if required) , and all other
accessories as per drawing, specifications and direction of the
Engineer-in-charge.
18.1 Supply & installation of concealed type fan hook of ½ inch 40 Each 15.00 98.60
grade plain bar with box(size:4 & ½ dia & depth 2 inch) made
of 16SWG sheet steel box of approved quality everything
complete as per drawing, specifications and direction of the
Engineer-in-charge
Sub total
Tax 4%
G.Total=
In word:-
NT ACCOMMODATION
Amount (taka)
1373.22
5,359.88
131.22
5000
72,485.69
487.38
1373.22
4,019.70
98.41
1550
43,947.04
290.55
450
0
250
42,863.87
5764.17
-
19,546.7 100
-
11,384.8 350
40,730.02 86.2011
-
116,336.94
750 5214.849
177,246.87
2522.72 720
-
91,496.02
5208.98 180
55,048.18
1682.618 335.2591
-
64,389.73
5208.98 126.6738
3,581.91
250 146.8242
-
18,969.71
5 127548.7
-
44,493.82
81 5629.084
17,565.06
70
91800.00
89250.00
52500.00
44,296.50
220 2008.912
2465.00
3 2500
3944.00
2 4000
2465.00
5 2500
2500.00
5 2500
3944.00
5 4000
788.80
5 400
788.80
5 400
2366.40
10 1200
788.80
5 400
788.80
5 400
4338.40
7 1100
3549.60
12 900
2958.00
5 1500
98.60
5 100
295.80
5 100
23171.00
1 23500
0.00 0 400
1392.86 40 380
384.87 12 350
0.00
0.00
1972.00 2 1000
824.72 300 30
1603.62 700 25
12325.00 1200 25
11585.50 200 47
14395.60 150 73
25636.00 100 130
1972.00 100 20
11989.76
48 380
394.40 6 100
394.40 5 100
591.60 4 150
591.60 8 150
197.20 5 50
197.20 4 50
236.64 8 60
2169.20 77 40
2760.80
9 350
1183.20
6 400
15000.00 1 20500
53244.00
28 3600
1479.00
28 100
1,329,666.41
53,186.66
1,382,853.07
SCHEDULE OF RATES FOR THE MODIFICATION WORKS AT RADIOLOGY
DEPARTMENT
1.1 Lintels, Railing, Drop walls, Sunshade, False ceiling cft 35 200 7000.00
Form work/shuttering, prop and necessary
2.0
support etc.(steel)
2.1 Lintels, Railing, Drop walls, Sunshade, False ceiling sft 70 28 1960.00
Reinforcement in R.C.C Steel reinforcement works
in RCC works providing deformed and plain bars of
any size manufactured from billets having min. yield
strength as specified below unless other wise
specified, cleaning the steel surface, cutting the bars
in required length, making the bars as per shape and
size, placing the bars in position, binding & fixing the
bars in position by using 22 BWG G.I binding wire
3.0 providing necessary blocks, chair, hangers, spacers
etc.(No payment shall be made for overweight and
wastage, payment shall be made as per approved bar
bending schedule),all works complete in all respect in
all floors. (BSRM)
IN WORDS: TWO LAC, FOURTEEN THOUSAND, SIX HUNDRED & THIRTY FIVE TAKA ONLY