Professional Documents
Culture Documents
PROJECT:
LUSAIL PLAZA TOWER PLOT 3 & 4
CLIENT CONSULTANT CONTRACTORS SUPPLIER
AL SAMRYA TRADING
SAMRYA QATAR ERGA QATAR & NABINA CERAMIC
CONTRACTING CO.
MANUFACTURED BY:
PROJECT:
AL SAMRYA TRADING
SAMRYA QATAR 0 ERGA QATAR & NABINA CERAMIC
CONTRACTING CO.
INDEX:-
SECTION:
PROJECT SPECIFICATIONS 1
COMPLIANCE STATEMENT 2
VENDOR LIST OR PQ 3
DRAWING APPLICATION 4
PRODUCT CATALOGUE 6
SAMPLE PICTURE 7
GSAS APPROVAL 8
CERTIFICATES 9
WARRANTY CERTIFICATES 10
CR COPY 12
GA DRAWINGS 14
INSTALLATION MANUAL 15
PROJECT:
AL SAMRYA TRADING
SAMRYA QATAR 0 ERGA QATAR & NABINA CERAMIC
CONTRACTING CO.
SECTION - 1
PROJECT SPECIFICATIONS
PLUMBING FIXTURES
LUSAIL REAL ESTATE DEVELOPMENT COMPANY
BP12 – LUSAIL TOWERS – MAIN WORKS
PART 1 GENERAL
A. Descriptive WORK
1. For design and general performance requirements, refer to Division 01 of the specification. Specific
performance requirements are provided in each trade Section.
2. Complete the Detailed Design, manufacture, supply, install and warrant the WORK whilst complying
with the visual intent indicated on the Lead Details and criteria stated in the specification.
3. Where no material, product or supplier is indicated in the specification, propose suitable materials
and systems prior to CONTRACT award which comply with the visual intent and performance criteria
stated and remain fully responsible for the Detailed Design of the WORK.
4. Where a particular material, product or supplier is indicated in the specification, such material,
product or supplier shall be deemed indicative representing the LREDC's design intent only. The
CONTRACTOR may complete the installation using that product, or such other confirmed as
acceptable by the LREDC in writing, but shall remain fully responsible for the Detailed Design and
performance of the WORK.
B. Scope of WORK
C. This Section of the specification, when read in conjunction with the Lead Details, provides particular
requirements with respect to the WORK, which include the following:
1. WC suites.
2. Basins and sinks.
3. Taps.
4. Accessories.
5. Showers.
6. Cleaner's sink.
D. Particular Interfaces
1. Complete the Detailed Design of all interfaces with adjoining trades prior to commencement of
manufacture.
2. Ensure that all interfaces are fully coordinated prior to commencement.
A. Wcs/ Cisterns
1. SAN-101 Wall mounted WC suite
2. SAN-102 Premium WC suite
B. Hand Washbasins
1. SAN-301 Wash hand basin (typical)
2. SAN-302 Wash hand basin (typical disabled)
3. SAN-303 Wash hand basin (executive)
4. SAN-304 Wash hand basin (executive disabled)
5. SAN-305 Wash hand basin
6. SAN-306 Wash hand basin (disabled)
C. Cleaners' Sinks
1. SAN-401 Cleaner's sink
D. Showers
1. SAN-501 Shower
E. Accessories
1. SAN-701 Hand held bidet shower hose
2. SAN-702 Concealed automatic soap dispenser
3. SAN-703 Concealed paper towel dispenser
4. SAN-704 Concealed hand dryer
1.3 SUBMITTALS
A. Tender Submittals
1. Tender Response
a. Provide tender submittals in accordance with the requirements of Division 01 of the
specification.
b. Submit a design response with the Tender proposal, to include all profiles of typical conditions,
with dimensions.
c. The Tender design response shall include:
1). Samples where specified.
2). List of Tests included.
3). QA/ QC programme.
4). List of proposed CONTRACTOR's Drawings.
5). Summary of deviations from the specification.
6). Copies of technical data prepared for each product or material proposed, which lists the
specified performance of each material and product to be used.
7). A list of proposed suppliers and subcontractors intended to be used.
PART 2 PRODUCTS
A. Wcs/ Cisterns
1. SAN-101 Wall mounted WC suite
a. Refer to the Sanitaryware Schedule.
2. SAN-102 Premium WC suite
a. Refer to the Sanitaryware Schedule.
B. Hand Washbasins
1. SAN-301 Wash hand basin (typical)
a. Refer to the Sanitaryware Schedule.
2. SAN-302 Wash hand basin (typical disabled)
a. Refer to the Sanitaryware Schedule.
3. SAN-303 Wash hand basin (executive)
a. Refer to the Sanitaryware Schedule.
4. SAN-304 Wash hand basin (executive disabled)
a. Refer to the Sanitaryware Schedule.
5. SAN-305 Wash hand basin
a. Refer to the Sanitaryware Schedule.
6. SAN-306 Wash hand basin (disabled)
a. Refer to the Sanitaryware Schedule.
C. Cleaners' Sinks
1. SAN-401 Cleaner's sink
a. Refer to the Sanitaryware Schedule.
D. Showers
1. SAN-501 Shower
a. Refer to the Sanitaryware Schedule.
E. Accessories
1. SAN-701 Hand held bidet shower hose
a. Refer to the Sanitaryware Schedule.
2. SAN-702 Concealed automatic soap dispenser
a. Refer to the Sanitaryware Schedule.
3. SAN-703 Concealed paper towel dispenser
a. Refer to the Sanitaryware Schedule.
4. SAN-704 Concealed hand dryer
a. Refer to the Sanitaryware Schedule.
5. SAN-705 Dual flush sensor
a. Refer to the Sanitaryware Schedule.
6. SAN-706 Under counter waste bin
a. Refer to the Sanitaryware Schedule.
7. SAN-707 Sensor tap
a. Refer to the Sanitaryware Schedule.
8. SAN-710 Concealed toilet brush
a. Refer to the Sanitaryware Schedule.
9. SAN-711 Concealed sanitary bin
a. Refer to the Sanitaryware Schedule.
10. SAN-712 Concealed toilet roll dispenser
a. Refer to the Sanitaryware Schedule.
11. SAN-713 Disabled toilet - Toilet roll dispenser
a. Refer to the Sanitaryware Schedule.
12. SAN-714 Disabled cubicle - Integrated soap dispenser
a. Refer to the Sanitaryware Schedule.
13. SAN-715 Disabled toilet - Grab bars
a. Refer to the Sanitaryware Schedule.
2.2 MATERIALS
A. General
B. The LREDC will not accept any brand names on any products or items of equipment to be visible in the
finished WORK.
C. Sustainable Design
1. Sealants shall comply with the testing and product requirements of the Standard Method for the
Testing and Evaluation of Volatile Organic Chemical Emissions from Indoor Sources Using
Environmental Chambers, of authorities having jurisdiction.
a. Sealant shall have a VOC content as stated in the GSAS section of Division 01.
D. Generally
1. All vitreous ware shall be fired vitreous chinaware of the best quality, non-absorbent and burned so
that the whole mass is thoroughly fused and vitrified, producing a material, consistent in colour,
which when fractured shall show a homogeneous mass, close grained and free from pores.
2. The glazing of vitreous china fixtures shall be thoroughly fused and unitised to the body, without
discolouration, chips or flaws, and shall be free from craze. Warped or otherwise imperfect fixtures
shall not be accepted.
3. One manufacturer shall supply all fixtures, unless specified otherwise.
E. Metals
G. Sealant Pointing
H. Sealant pointing (at joints between appliance/ fitting and substrate) shall be silicone based sealant in
accordance with Section 079200 of the specification. Colour shall be 'White' or to complement the adjacent
appliance/ fitting or as agreed.
PART 3 EXECUTION
3.1 WORKMANSHIP
A. General
1. Appliances and accessories shall be so assembled and fixed that surfaces designed to falls drain
as intended.
2. Non-ferrous or stainless steel fastenings shall be used unless otherwise specified.
3. Jointing and bedding compounds recommended in writing by the manufacturers of the appliances,
accessories and pipes being jointed or bedded shall be used.
4. Appliances shall not be used for any purpose until Practical Completion.
5. On Practical Completion, protective coverings, tapes shall be removed and appliances checked for
damage and defects. They shall be tested for satisfactory operation and all damaged or defective
components/ accessories replaced. The whole installation shall be thoroughly cleaned.
6. Noggings and bearers required to support sanitary appliances and fittings shall be accurately
positioned, securely fixed and concealed from view.
7. Sealant application shall be as Section 079200 of the specification.
B. Appliances
1. WC seats and lids shall be stable when raised and capable of remaining in a vertical position.
2. Cisterns:
END OF SECTION
PART 1 - GENERAL
A. Drawings and general provisions of the Contract, including General and Supplementary
Conditions and Division 01 Specification Sections, apply to this Section.
B. The Qatar construction specification (QCS 2014) shall form the basis of the project specification.
The technical specification is supplemental to QCS (latest revision) and should be read in
conjunction with QCS and all other contract documents. In case of contradiction or discrepancy
between QCS and technical specifications, CONTRACTOR shall incorporate whichever is more
stringent.
1.2 SUMMARY
A. Section Includes:
1. Water closets.
2. Toilet seats.
3. Supports.
1.3 DEFINITIONS
A. Effective Flush Volume: Average of two reduced flushes and one full flush per fixture.
1. Product Data: as per GSAS For water consumption 3.75 L per flush (4.5 / 3 L Dual flush).
C. Shop Drawings: Include diagrams for power, signal, and control wiring.
A. Furnish extra materials that are packaged with protective covering for storage and identified with
labels describing contents.
1. Flushometer-Tank Repair Kits: Equal to 10 per cent of amount of each type installed, but
no fewer than two of each type.
PART 2 - PRODUCTS
A. Toilet Seats :
2.5 SUPPORTS
PART 3 - EXECUTION
3.1 EXAMINATION
A. Examine roughing-in of water supply and sanitary drainage and vent piping systems to verify
actual locations of piping connections before water-closet installation.
B. Examine walls and floors for suitable conditions where water closets will be installed.
C. Proceed with installation only after unsatisfactory conditions have been corrected.
3.2 INSTALLATION
A. Water-Closet Installation:
B. Support Installation:
1. Install supports, affixed to building substrate, for floor-mounted, back-outlet water closets.
2. Use carrier supports with waste-fitting assembly and seal.
3. Install floor-mounted, back-outlet water closets attached to building floor substrate, onto
waste-fitting seals; and attach to support.
4. Install wall-mounted, back-outlet water-closet supports with waste-fitting assembly and
waste-fitting seals; and affix to building substrate.
E. Joint Sealing:
1. Seal joints between water closets and walls and floors using sanitary-type, one-part,
mildew-resistant silicone sealant.
2. Match sealant colour to water-closet colour.
3. Comply with sealant requirements specified in Section 07 92 00 "Joint Sealants."
3.3 CONNECTIONS
A. Connect water closets with water supplies and soil, waste, and vent piping. Use size fittings
required to match water closets.
B. Comply with water piping requirements specified in Section 22 11 16 "Domestic Water Piping."
C. Comply with soil and waste piping requirements specified in Section 22 13 16 "Sanitary Waste
and Vent Piping."
D. Where installing piping adjacent to water closets, allow space for service and maintenance.
3.4 ADJUSTING
A. Operate and adjust water closets and controls. Replace damaged and malfunctioning water
closets, fittings, and controls.
A. Clean water closets and fittings with manufacturers' recommended cleaning methods and
materials.
C. Do not allow use of water closets for temporary facilities unless approved in writing by LREDC.
PART 1 - GENERAL
A. Drawings and general provisions of the Contract, including General and Supplementary
Conditions and Division 01 Specification Sections, apply to this Section.
B. The Qatar construction specification (QCS 2014) shall form the basis of the project specification.
The technical specification is supplemental to QCS (latest revision) and should be read in
conjunction with QCS and all other contract documents. In case of contradiction or discrepancy
between QCS and technical specifications, CONTRACTOR shall incorporate whichever is more
stringent.
1.2 SUMMARY
A. Section Includes:
1. Lavatories.
2. Faucets.
3. Supports.
C. Shop Drawings: Include diagrams for power, signal, and control wiring of automatic faucets.
A. Operation and Maintenance Data: For lavatories and faucets to include in operation and
maintenance manuals.
A. Furnish extra materials that match products installed and that are packaged with protective
covering for storage and identified with labels describing contents.
1. Faucet Washers and O-Rings: Equal to 10 per cent of amount of each type and size
installed.
2. Faucet Cartridges and O-Rings: Equal to 5 per cent of amount of each type and size
installed.
PART 2 - PRODUCTS
A. NSF Standard: Comply with NSF/ANSI 61 Annex G, "Drinking Water System Components -
Health Effects," for faucet materials that will be in contact with potable water.
2.4 SUPPORTS
A. NSF Standard: Comply with NSF/ANSI 61 Annex G, "Drinking Water System Components -
Health Effects," for supply-fitting materials that will be in contact with potable water.
C. Trap:
1. Size: DN 40 by DN 32.
2. Material: Chrome-plated, two-piece, cast-brass trap and swivel elbow with 0.83-mm- thick
brass tube to wall; and chrome-plated, brass or steel wall flange.
3. Material: Stainless-steel, two-piece trap and swivel elbow with 0.30-mm- thick stainless-
steel tube to wall; and stainless-steel wall flange.
2.7 SUPPORTS
PART 3 - EXECUTION
3.1 EXAMINATION
A. Examine roughing-in of water supply and sanitary drainage and vent piping systems to verify
actual locations of piping connections before lavatory installation.
B. Examine counters and walls for suitable conditions where lavatories will be installed.
C. Proceed with installation only after unsatisfactory conditions have been corrected.
3.2 INSTALLATION
D. Install wall flanges or escutcheons at piping wall penetrations in exposed, finished locations.
Use deep-pattern escutcheons if required to conceal protruding fittings. Comply with escutcheon
requirements specified in Section 22 05 18 "Escutcheons for Plumbing Piping."
E. Seal joints between lavatories, counters, and walls using sanitary-type, one-part, mildew-
resistant silicone sealant. Match sealant colour to fixture colour. Comply with sealant
requirements specified in Section 07 92 00 "Joint Sealants."
F. Install protective shielding pipe covers and enclosures on exposed supplies and waste piping of
accessible lavatories. Comply with requirements in Section 22 07 19 "Plumbing Piping
Insulation."
3.3 CONNECTIONS
A. Connect fixtures with water supplies, stops, and risers, and with traps, soil, waste, and vent
piping. Use size fittings required to match fixtures.
B. Comply with water piping requirements specified in Section 22 11 16 "Domestic Water Piping."
C. Comply with soil and waste piping requirements specified in Section 22 13 16 "Sanitary Waste
and Vent Piping."
3.4 ADJUSTING
A. Operate and adjust lavatories and controls. Replace damaged and malfunctioning lavatories,
fittings, and controls.
B. Clean lavatories, faucets, and other fittings with manufacturers' recommended cleaning methods
and materials.
D. Do not allow use of lavatories for temporary facilities unless approved in writing by LREDC.
PART 1 - GENERAL
A. Drawings and general provisions of the Contract, including General and Supplementary
Conditions and Division 01 Specification Sections, apply to this Section.
B. The Qatar construction specification (QCS 2014) shall form the basis of the project specification.
The technical specification is supplemental to QCS (latest revision) and should be read in
conjunction with QCS and all other contract documents. In case of contradiction or discrepancy
between QCS and technical specifications, CONTRACTOR shall incorporate whichever is more
stringent.
1.2 SUMMARY
A. Section Includes:
1. Janitor sinks.
2. Kitchen sinks.
3. Sink faucets.
4. Grout.
A. Furnish extra materials that match products installed and that are packaged with protective
covering for storage and identified with labels describing contents.
1. Faucet Washers and O-Rings: Equal to 10 per cent of amount of each type and size
installed.
2. Faucet Cartridges and O-Rings: Equal to 5 per cent of amount of each type and size
installed.
PART 2 - PRODUCTS
5. Drain Piping: Schedule 40 ABS or PVC, DN 40 P-trap; tubular waste to wall; continuous
waste; and wall escutcheon(s).
6. Faucet flow rate : As per GSAS (5.0 LPM).
A. NSF Standard: Comply with NSF/ANSI 61 Annex G, "Drinking Water System Components -
Health Effects," for faucet-spout materials that will be in contact with potable water.
2.4 GROUT
PART 3 - EXECUTION
3.1 EXAMINATION
A. Examine roughing-in of water supply and sanitary drainage and vent piping systems to verify
actual locations of piping connections before sink installation.
B. Examine walls, floors, and counters for suitable conditions where sinks will be installed.
C. Proceed with installation only after unsatisfactory conditions have been corrected.
3.2 INSTALLATION
E. Install water-supply piping with stop on each supply to each sink faucet.
1. Exception: Use ball or gate valves if supply stops are not specified with sink. Comply with
valve requirements specified in Section 22 05 23.12 "Ball Valves for Plumbing Piping" and
Section 22 05 23.15 "Gate Valves for Plumbing Piping."
2. Install stops in locations where they can be easily reached for operation.
F. Install wall flanges or escutcheons at piping wall penetrations in exposed, finished locations.
Use deep-pattern escutcheons if required to conceal protruding fittings. Comply with escutcheon
requirements specified in Section 22 05 18 "Escutcheons for Plumbing Piping."
G. Seal joints between sinks and counters, floors, and walls using sanitary-type, one-part, mildew-
resistant silicone sealant. Match sealant colour to fixture colour. Comply with sealant
requirements specified in Section 07 92 00 "Joint Sealants."
H. Install protective shielding pipe covers and enclosures on exposed supplies and waste piping of
accessible sinks. Comply with requirements in Section 22 07 19 "Plumbing Piping Insulation."
3.3 CONNECTIONS
A. Connect sinks with water supplies, stops, and risers, and with traps, soil, waste, and vent piping.
Use size fittings required to match fixtures.
B. Comply with water piping requirements specified in Section 22 11 16 "Domestic Water Piping."
C. Comply with soil and waste piping requirements specified in Section 22 13 16 "Sanitary Waste
and Vent Piping."
3.4 ADJUSTING
A. Operate and adjust sinks and controls. Replace damaged and malfunctioning sinks, fittings, and
controls.
B. Clean sinks, faucets, and other fittings with manufacturers' recommended cleaning methods and
materials.
D. Do not allow use of sinks for temporary facilities unless approved in writing by LREDC.
AL SAMRYA TRADING
SAMRYA QATAR 0 ERGA QATAR & NABINA CERAMIC
CONTRACTING CO.
SECTION - 2
COMPLIANCE STATEMENT
Bid Pack: Package BP12C Document No. Revision Date
Contractor: Hyundai Engineering & Construction Co.Ltd.
Material Description:
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
MANUFACTURER
BRAND : VITRA Vitra Karo San. ve Tic. A.S.
4 Eylül Mahallesi İsmet İnönü
CODE : 742-1420 + 300-1029 Caddesi No:269
FINISH : GOLD 11300 Bozuyuk - Bilecik
Phone: +90 228 316 00 94 /
2.5 SUPPORTS COUNTRY : TURKEY Fax: +90 228 314 16 20
A. Water Closet Carrier: www.vitraglobal.com
1. Manufacturers and products: as per section 99 99
99 Appendix A - Preferred MEP Vendor List.
2 224000 SAN-705 2. Standard: ASME A112.6.1M.
3. Description: Waste-fitting assembly, as required to
match drainage piping material and arrangement
with faceplates, couplings gaskets, and feet; bolts SUPPLIER
and hardware matching fixture. Include NABINA CERAMIC
Al Wakrah Road;
Airport Street
P.O. Box No. 130-Doha - Qatar
T: +974-44652345 /
F: +974-44652386
www.nabinaceramic.com
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
MANUFACTURER
BRAND : NOKEN
Noken Porcelanosa Bathroom
Section 20: Drainage Works for Buildings
CODE : 100220153 Carretera CV-20 km2
Part 02: Internal Drainage Works
12540 Villareal, Castellón
FINISH : CHROME
(Spain)
2.8 SANITARYWARE INSTALLATIONS
COUNTRY : SPAIN +34 964 50 64 50
2.8.9 Showers
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
MANUFACTURER
Vitra Karo San. ve Tic. A.S.
BRAND : VITRA
4 Eylül Mahallesi İsmet İnönü
Caddesi No:269
CODE : 742-5800-02 11300 Bozuyuk - Bilecik
Phone: +90 228 316 00 94 /
2.5 SUPPORTS FINISH : N/A Fax: +90 228 314 16 20
A. Water Closet Carrier: www.vitraglobal.com
1. Manufacturers and products: as per section 99 99 COUNTRY : TURKEY
99 Appendix A - Preferred MEP Vendor List.
10 224000 - 2. Standard: ASME A112.6.1M.
3. Description: Waste-fitting assembly, as required to
match drainage piping material and arrangement
with faceplates, couplings gaskets, and feet; bolts SUPPLIER
and hardware matching fixture. Include NABINA CERAMIC
Al Wakrah Road;
Airport Street
P.O. Box No. 130-Doha - Qatar
T: +974-44652345 /
F: +974-44652386
www.nabinaceramic.com
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
TAP,
• Spout length: 122 mm
• With flow straightener
• Ø 65 mm rosette included
• 180° turn ceramic disc cartridge
2.3 SINK FAUCETS MANUFACTURER
Vitra Karo San. ve Tic. A.S.
A. NSF Standard: Comply with NSF/ANSI 61 BRAND : VITRA 4 Eylül Mahallesi İsmet İnönü
Annex G, "Drinking Water System Components - Caddesi No:269
Health Effects," for faucet-spout materials that CODE : A41584EXP 11300 Bozuyuk - Bilecik
will be in contact with potable water. Phone: +90 228 316 00 94 /
B. Sink Faucets: Manual type, single-control mixing FINISH : CHROME Fax: +90 228 314 16 20
valve. www.vitraglobal.com
1. General-Duty, Solid-Brass Faucets. COUNTRY : TURKEY
a. Manufacturers and products: as per section 99 99
16 224000 - 99 Appendix A - Preferred MEP Vendor List.
2. Standard: ASME A112.18.1/CSA B125.1.
3. General: Include hot- and cold-water indicators;
coordinate faucet inlets with supplies and fixture SUPPLIER
hole punchings; coordinate outlet with spout and NABINA CERAMIC
sink receptor. Al Wakrah Road;
4. Body Material: General-duty, solid brass. Airport Street
5. Finish: Polished chrome plate. P.O. Box No. 130-Doha - Qatar
6. Maximum Flow Rate: 6.8 L/min. T: +974-44652345 /
7. Vacuum Breaker: Required for hose outlet. F: +974-44652386
8. Spout Outlet: Aerator. www.nabinaceramic.com
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
MANUFACTURER
BRAND : GENWEC GENWEC WASHROOM
EQUIPMENT & COMP
CODE : GW13 19 06 02 Distrito Económico de
L'Hospitalet de Llobretat
FINISH : STAINLESS STEEL Avinguda Joan Carles I, 46-48
08908 L'Hospitalet de
COUNTRY : SPAIN Llobregat - Barcelona (España)
Central telephone: +34 936 018
040
17 224000 SAN-702 N/A
SUPPLIER
NABINA CERAMIC
Al Wakrah Road;
Airport Street
P.O. Box No. 130-Doha - Qatar
T: +974-44652345 /
F: +974-44652386
www.nabinaceramic.com
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
BRAND : GENWEC
MANUFACTURER
CODE : GW03 28 04 01 GENWEC WASHROOM
EQUIPMENT & COMP
FINISH : STAINLESS STEEL - SATIN Distrito Económico de
Section 20: Drainage Works for Buildings
L'Hospitalet de Llobretat
Part 02: Internal Drainage Works
COUNTRY : SPAIN Avinguda Joan Carles I, 46-48
08908 L'Hospitalet de
2.8 SANITARYWARE INSTALLATIONS
Llobregat - Barcelona (España)
Central telephone: +34 936 018
2.8.1 General
040
18 224000 SAN-703
1 Sanitary fittings shall, unless otherwise stated in
the Project Documentation, be as described in the
following Clauses.
SUPPLIER
NABINA CERAMIC
2 Where screws are used to fix sanitary appliances to
Al Wakrah Road;
concrete, blockwork or brickwork they shall be
Airport Street
rust-proofed steel and plugged.
P.O. Box No. 130-Doha - Qatar
T: +974-44652345 /
F: +974-44652386
www.nabinaceramic.com
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
BRAND : GENWEC
MANUFACTURER
CODE : GW01 33 04 01 GENWEC WASHROOM
EQUIPMENT & COMP
FINISH : BRUSHED STAINLESS STEEL Distrito Económico de
Section 20: Drainage Works for Buildings
COUNTRY : SPAIN L'Hospitalet de Llobretat
Part 02: Internal Drainage Works
Avinguda Joan Carles I, 46-48
08908 L'Hospitalet de
2.8 SANITARYWARE INSTALLATIONS
Llobregat - Barcelona (España)
Central telephone: +34 936 018
2.8.1 General
040
19 224000 SAN-704
1 Sanitary fittings shall, unless otherwise stated in the
Project Documentation, be as described in the following
Clauses.
SUPPLIER
NABINA CERAMIC
2 Where screws are used to fix sanitary appliances to
Al Wakrah Road;
concrete, blockwork or brickwork they shall be rust-
Airport Street
proofed steel and plugged.
P.O. Box No. 130-Doha - Qatar
T: +974-44652345 /
F: +974-44652386
www.nabinaceramic.com
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
BRAND : GENWEC
MANUFACTURER
CODE : GW04 10 01 00 GENWEC WASHROOM
EQUIPMENT & COMP
FINISH : BRUSHED SATIN STAINLESS STEEL Distrito Económico de
Section 20: Drainage Works for Buildings
COUNTRY : SPAIN L'Hospitalet de Llobretat
Part 02: Internal Drainage Works
Avinguda Joan Carles I, 46-48
08908 L'Hospitalet de
2.8 SANITARYWARE INSTALLATIONS
Llobregat - Barcelona (España)
Central telephone: +34 936 018
2.8.1 General
040
20 224000 SAN-714
1 Sanitary fittings shall, unless otherwise stated in the
Project Documentation, be as described in the
following Clauses.
SUPPLIER
NABINA CERAMIC
2 Where screws are used to fix sanitary appliances to
Al Wakrah Road;
concrete, blockwork or brickwork they shall be rust-
Airport Street
proofed steel and plugged.
P.O. Box No. 130-Doha - Qatar
T: +974-44652345 /
F: +974-44652386
www.nabinaceramic.com
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
BRAND : GENWEC
MANUFACTURER
CODE : GW11 03 04 01 GENWEC WASHROOM
EQUIPMENT & COMP
FINISH : SATIN STAINLESS STEEL
Distrito Económico de
Section 20: Drainage Works for Buildings
COUNTRY : SPAIN L'Hospitalet de Llobretat
Part 02: Internal Drainage Works
Avinguda Joan Carles I, 46-48
08908 L'Hospitalet de
2.8 SANITARYWARE INSTALLATIONS
Llobregat - Barcelona (España)
Central telephone: +34 936 018
2.8.1 General
040
21 224000 SAN-719
1 Sanitary fittings shall, unless otherwise stated in
the Project Documentation, be as described in the
following Clauses.
SUPPLIER
NABINA CERAMIC
2 Where screws are used to fix sanitary appliances to
Al Wakrah Road;
concrete, blockwork or brickwork they shall be
Airport Street
rust-proofed steel and plugged.
P.O. Box No. 130-Doha - Qatar
T: +974-44652345 /
F: +974-44652386
www.nabinaceramic.com
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
BRAND : GENWEC
MANUFACTURER
CODE : GW11 05 04 01 GENWEC WASHROOM
EQUIPMENT & COMP
FINISH : SATIN STAINLESS STEEL
Distrito Económico de
Section 20: Drainage Works for Buildings
COUNTRY : SPAIN L'Hospitalet de Llobretat
Part 02: Internal Drainage Works
Avinguda Joan Carles I, 46-48
08908 L'Hospitalet de
2.8 SANITARYWARE INSTALLATIONS
Llobregat - Barcelona (España)
Central telephone: +34 936 018
2.8.1 General
040
22 224000 SAN-719
1 Sanitary fittings shall, unless otherwise stated in
the Project Documentation, be as described in the
following Clauses.
SUPPLIER
NABINA CERAMIC
2 Where screws are used to fix sanitary appliances to
Al Wakrah Road;
concrete, blockwork or brickwork they shall be
Airport Street
rust-proofed steel and plugged.
P.O. Box No. 130-Doha - Qatar
T: +974-44652345 /
F: +974-44652386
www.nabinaceramic.com
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
BRAND : GENWEC
MANUFACTURER
CODE : GW05 28 04 02 GENWEC WASHROOM
EQUIPMENT & COMP
FINISH : POLISHED STAINLESS STEEL
Distrito Económico de
Section 20: Drainage Works for Buildings
COUNTRY : SPAIN L'Hospitalet de Llobretat
Part 02: Internal Drainage Works
Avinguda Joan Carles I, 46-48
08908 L'Hospitalet de
2.8 SANITARYWARE INSTALLATIONS
Llobregat - Barcelona (España)
Central telephone: +34 936 018
2.8.1 General
040
24 224000 SAN-710
1 Sanitary fittings shall, unless otherwise stated in
the Project Documentation, be as described in the
following Clauses.
SUPPLIER
NABINA CERAMIC
2 Where screws are used to fix sanitary appliances
Al Wakrah Road;
to concrete, blockwork or brickwork they shall be
Airport Street
rust-proofed steel and plugged.
P.O. Box No. 130-Doha - Qatar
T: +974-44652345 /
F: +974-44652386
www.nabinaceramic.com
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
BRAND : GENWEC
MANUFACTURER
CODE : GW06 13 04 01 GENWEC WASHROOM
EQUIPMENT & COMP
FINISH : BRUSHED STAINLESS STEEL
Distrito Económico de
Section 20: Drainage Works for Buildings
COUNTRY : SPAIN L'Hospitalet de Llobretat
Part 02: Internal Drainage Works
Avinguda Joan Carles I, 46-48
08908 L'Hospitalet de
2.8 SANITARYWARE INSTALLATIONS
Llobregat - Barcelona (España)
Central telephone: +34 936 018
2.8.1 General
040
25 224000 SAN-711
1 Sanitary fittings shall, unless otherwise stated in the
Project Documentation, be as described in the
following Clauses.
SUPPLIER
NABINA CERAMIC
2 Where screws are used to fix sanitary appliances to
Al Wakrah Road;
concrete, blockwork or brickwork they shall be rust-
Airport Street
proofed steel and plugged.
P.O. Box No. 130-Doha - Qatar
T: +974-44652345 /
F: +974-44652386
www.nabinaceramic.com
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
BRAND : GENWEC
MANUFACTURER
CODE : GW03 02 04 01 GENWEC WASHROOM
EQUIPMENT & COMP
FINISH : BRUSHED SATIN STAINLESS STEEL
Distrito Económico de
Section 20: Drainage Works for Buildings
COUNTRY : SPAIN L'Hospitalet de Llobretat
Part 02: Internal Drainage Works
Avinguda Joan Carles I, 46-48
08908 L'Hospitalet de
2.8 SANITARYWARE INSTALLATIONS
Llobregat - Barcelona (España)
Central telephone: +34 936 018
2.8.1 General
040
26 224000 SAN-712
1 Sanitary fittings shall, unless otherwise stated in the
Project Documentation, be as described in the
following Clauses.
SUPPLIER
NABINA CERAMIC
2 Where screws are used to fix sanitary appliances to
Al Wakrah Road;
concrete, blockwork or brickwork they shall be rust-
Airport Street
proofed steel and plugged.
P.O. Box No. 130-Doha - Qatar
T: +974-44652345 /
F: +974-44652386
www.nabinaceramic.com
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
BRAND : GENWEC
MANUFACTURER
CODE : GW03 09 04 02 GENWEC WASHROOM
EQUIPMENT & COMP
FINISH : POLISHED STAINLESS STEEL
Distrito Económico de
Section 20: Drainage Works for Buildings
COUNTRY : SPAIN L'Hospitalet de Llobretat
Part 02: Internal Drainage Works
Avinguda Joan Carles I, 46-48
08908 L'Hospitalet de
2.8 SANITARYWARE INSTALLATIONS
Llobregat - Barcelona (España)
Central telephone: +34 936 018
2.8.1 General
040
27 224000 SAN-713
1 Sanitary fittings shall, unless otherwise stated in the
Project Documentation, be as described in the
following Clauses.
SUPPLIER
NABINA CERAMIC
2 Where screws are used to fix sanitary appliances to
Al Wakrah Road;
concrete, blockwork or brickwork they shall be rust-
Airport Street
proofed steel and plugged.
P.O. Box No. 130-Doha - Qatar
T: +974-44652345 /
F: +974-44652386
www.nabinaceramic.com
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
- Brass
BRAND : SCHLOSSER
MANUFACTURER
CODE : 7106 Schlosser Heiztechnik Gruppe
Polska Spółka z ograniczoną
FINISH : CHROME
odpowiedzialnością Sp.k.
Section 20: Drainage Works for Buildings
COUNTRY : GERMANY ul. Przełęcz 27, 60-115 Poznań
Part 02: Internal Drainage Works
Telephone: +48 061 830 50 05
fax: +48 061 830 73 63
2.8 SANITARYWARE INSTALLATIONS
office@schlosser.com.pl
2.8.1 General
t.karczewski@schlosser.com.pl
28 224000 SAN-707 a.maschke@schlosser.com.pl
1 Sanitary fittings shall, unless otherwise stated in the
Project Documentation, be as described in the
following Clauses.
SUPPLIER
NABINA CERAMIC
2 Where screws are used to fix sanitary appliances to
Al Wakrah Road;
concrete, blockwork or brickwork they shall be rust-
Airport Street
proofed steel and plugged.
P.O. Box No. 130-Doha - Qatar
T: +974-44652345 /
F: +974-44652386
www.nabinaceramic.com
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
- Brass
BRAND : SCHLOSSER
MANUFACTURER
CODE : 7111 Schlosser Heiztechnik Gruppe
Polska Spółka z ograniczoną
FINISH : CHROME
odpowiedzialnością Sp.k.
Section 20: Drainage Works for Buildings
COUNTRY : GERMANY ul. Przełęcz 27, 60-115 Poznań
Part 02: Internal Drainage Works
Telephone: +48 061 830 50 05
fax: +48 061 830 73 63
2.8 SANITARYWARE INSTALLATIONS
office@schlosser.com.pl
2.8.1 General
t.karczewski@schlosser.com.pl
29 224000 SAN-707 a.maschke@schlosser.com.pl
1 Sanitary fittings shall, unless otherwise stated in the
Project Documentation, be as described in the
following Clauses.
SUPPLIER
NABINA CERAMIC
2 Where screws are used to fix sanitary appliances to
Al Wakrah Road;
concrete, blockwork or brickwork they shall be rust-
Airport Street
proofed steel and plugged.
P.O. Box No. 130-Doha - Qatar
T: +974-44652345 /
F: +974-44652386
www.nabinaceramic.com
1- Supplier / Manufacturer from Preferred Vendors list : YES NO IF "NO" Submit prequalification endorsed by Consultant for Client Approval
2- Submittal Complies with Project Specification: YES NO
3- Submittal Endorsed and Approved by Consultant: YES NO IF "YES" attach endorsement by Consultant
4- Submittal (Material) is GSAS Applicable: YES NO
5- Submittal Complies with GSAS Requirements: YES NO IF "YES" attach relevant support documentation
Serial Specification Reference Drg Ref. / Specification Proposed Manufacturer / Supplier Remarks /
No. Section Page Clause Location Requirement Material / Product Details Attachment
Action: Comments:
A : Approved
B : Approved W/Comments
C : Not Approved
D : Commented&Resubmit
E : See Response Civil : Architect : MEP :
Action: Comments:
A : Approved
B : Approved W/Comments
C : Not Approved
D : Commented&Resubmit
E : See Response Civil : MEP : Architect :
AL SAMRYA TRADING
SAMRYA QATAR 0 ERGA QATAR & NABINA CERAMIC
CONTRACTING CO.
SECTION - 3
VENDOR LIST OR PQ
PROJECT:
AL SAMRYA TRADING
SAMRYA QATAR 0 ERGA QATAR & NABINA CERAMIC
CONTRACTING CO.
SECTION - 4
DRAWING APPLICATION
PROJECT:
AL SAMRYA TRADING
SAMRYA QATAR 0 ERGA QATAR & NABINA CERAMIC
CONTRACTING CO.
SECTION - 5
KOMODO
Articolo: KOMODO1
Materiale: Ceramica
Finitura: Ceramica Lucida
Peso lordo: kg 28 ca.
Peso netto: kg 26 ca.
Articolo: KOMODO3
Materiale: Ceramica
Finitura: Ceramica Satinata
Peso lordo: kg 28 ca.
Peso netto: kg 26 ca.
Dimensione imballo: cm 63 x 48 x 52
Descrizione: Vaso in ceramica lucida o satinata, sospeso con scarico a parete e sistema
senza brida, completo di sedile FLAT con sistema di sganciamento rapido, realizzato in
resina termoindurente con chiusura rallentata “soft-close”.
Article:
Material: Ceramic
Finish: Polished Ceramic
Gross weight: kg 28 ca.
Net weight: kg 26 ca.
Article:
Material: Ceramic
Finish: Satin Ceramic
Gross weight: kg 28 ca.
Net weight: kg 26 ca.
Packing dimensions: cm 63 x 48 x 52
Description: High gloss or satin suspended ceramic water closet with wall drain and
washdown rimless flushing, complete with seat and cover FLAT made of thermosetting
resin, quick release system and soft closing hinges.
18
Ø5,5 9 9 Ø2,5
5
5
9
14,5
13,5
26
9,5
36
42,5
42,5
33,5
24
24
Ø10,5
16,5
11,8
36 54
36
Prodotto conforme alla norma UNI EN. 997. Volume di flusso scarico pari a Lt. 4,5
Product compliant with UNI EN standard. 997. Volume of drainage flow equal to Lt. 4.5
1
SAN-705
Colour Gold
Anti-vandal Yes
Description
VitrA reserves the right to make changes in products and technical details without prior notice.
All drawings contain the necessary measurements which are subject to standard tolerances. For exact measurements, in particular for customized installation scenarios, it can only be
taken from the finished ceramic product.
SAN-716
2
SAN-501
GOLD
Bathroom Taps
SAN-707
TONO
Designed by
FOSTER + PARTNERS
Description Finish
Electronic tap with 1 water inlet. 3/8" connections. Battery 4x1,5V (AA). Flow
rate 5.5 l/min at 3 bar. Filters and batteries included. chrome 100184771 - N109390068
Warranty:For a warranty or other information on this product, visit our Web address: www.porcelanosa.com
Legal disclaimer: All details provided by the PORCELANOSA GROUP´s Product has an information purpose without any contractual value. In
order to obtain further information about the materials and their installation please visit our showrooms. PORCELANOSA GROUP reserves the
right to modify or delete any information on this site. The images and colours shown in this site may differ from the real ones.
COCOON - To be fitted in
combination with our advanced
build in system for super easy
installation.
Spout 220mm
Provided with a 5 l/min.
COMPONENTS
Item PB 32 + PB 01 EXT +
Code BOX02-R
Range Mixer
COCOON - To be fitted in
combination with our advanced
build in system for super easy
installation
This luxurious hand shower set
consists of a water connection, a
hand shower holder, a slim, water-
saving hand shower
COMPONENTS
Integra
Wall-hung WC pan, 54 cm
Without side holes
SAN-101
Collection Integra
Color White
Shape Round
Segments Middle-lower
Description
VitrA reserves the right to make changes in products and technical details without prior notice.
All drawings contain the necessary measurements which are subject to standard tolerances. For exact measurements, in particular for customized installation scenarios, it can only be
taken from the finished ceramic product.
SAN-705
Name Pro Flush Plate
Anti-vandal Yes
Description
VitrA reserves the right to make changes in products and technical details without prior notice.
All drawings contain the necessary measurements which are subject to standard tolerances. For exact measurements, in particular for customized installation scenarios, it can only be
taken from the finished ceramic product.
SAN-705
Collection
Description
VitrA reserves the right to make changes in products and technical details without prior notice.
All drawings contain the necessary measurements which are subject to standard tolerances. For exact measurements, in particular for customized installation scenarios, it can only be
taken from the finished ceramic product.
SAN-701
SCHEDA TECNICA TECHNICAL FEATURES
ON
G 1/2
28
OFF
94
120 cm
MATERIALI / MATERIALS
OTTONE CROMATO / CHROME PLATED BRASS
UNI EN 248
Via Leonardo da Vinci 53 20062 Cassano d'Adda (MI) Italy Tel. +39-0363 62651
info@daniel.it www.daniel.it
Technical Data Sheet Janitorial
Product description:
The Tahiti bucket sink is a heavy duty sanitaryware unit, for
use with buckets or food containers for rinsing and washing
down. Wall mounted with two adjustable front feet, fixing
brackets, hinged heavy gauge grid, stainless steel
splashback.
1
Technical Data Sheet Janitorial
SAN-401
Care Of Your Product
TO THE STOCKIST
Please store products in a cool, dry area.
Sinks should, where possible be stood on their ends supported by battens with the bowl uppermost.
If sinks are nested with bowls inside one another, place some dry cushioning material between them to protect the surfaces.
TO THE INSTALLER
DO handle with care to avoid scuffs and scratches during installation.
DO check that edges of sinks are dead level so that water will flow off the draining board.
DO NOT over-tighten plumbing or other mechanical fixtures.
DO NOT remove the plastic protective film applied to certain products until all installation work has been completed.
DO NOT stand/kneel on the drainer of sinks.
DO NOT drop mortar, plaster or similar substances onto the stainless steel.
TO THE USER
Stainless steel will give you a lifetime of trouble free use as long as you follow a few simple rules. If it appears to mark, don’t
worry, it is usually not the steel, but something deposited on it, which has caused the apparent stain.
DO - wash the product before use.
DO - clean the product regularly, using JIF, Goddard’s, or similar recommended cleaners. Follow the manufacturer’s instructions
carefully. Always rinse well with clean water and dry the surface with a soft cloth.
DO - use nylon or bristle brushes, not metal scrapers or wire brushes to loosen stubborn stains.
Never use wire wool pads, as they can scratch the steel.
DO - take care when handling sharp objects as they can scratch the surface of the steel. Any scratches will blend together over a
period of time and become less noticeable with age. There is no detriment to the corrosion resistance or general performance of
the material.
DO NOT - allow undiluted bleach to remain in contact with stainless steel (remember dishwasher powders, sterilising agents and
similar products all contain chlorides). Black pit marks can result and permanent damage can be caused. Dilute to manufacturer’s
instructions and always rinse with clean water.
DO NOT - soak clothes in bleach solutions for long periods. Always rinse bowl with clean water after use.
DO NOT - leave such substances as Mortar, Grouting cement, soldering flux, photographic developing fluids, silver dip, denture
liquids or food acids on the surface of the steel. Clean immediately and rinse well with clean water.
DO NOT - allow corrosive foodstuffs, such as fruit juices, damp salt, vinegar, mustards, pickles and mayonnaise to remain on the
surface of the steel for long periods. Wash and rinse away.
DO NOT - let hard water cause a build-up of lime or chalk deposits which can sometimes be seen as a greyish film. Clean regularly
with recommended cleaners to avoid this problem and always wipe dry with a soft cloth.
DO NOT - worry if the steel appears to rust. Usually it’s deposits of wire wool scouring pads, plumbers swarf, particles from
rusting storage tanks or other deposits on the surface which can be cleaned and rinsed away following your usual cleaning
procedure. Bases of washing up bowls can harbour such deposits – check regularly.
DO NOT - use coarse grit cleaners or wire wool pads when cleaning the steel. They will scratch the surface.
DO NOT - leave carbon steel objects such as bottle openers, scissors, whisks and other kitchen objects standing on the surface for
long periods, they can rust and leave marks.
Cleaning Regime
Oil & Grease Marks. Degreasing fluid or cellulose Rinse with soap & water.
thinners.
Stubborn marks, stains and light Mild abrasive creams ( Sif / Shiny Heavy stains can be loosened by
discoloration. sinks). soaking with Metsoak or Hi-Phos.
Rinse thoroughly after soaking as
these products cause rust type
marks if left.
Heavy discoloration or heat tint. Use metal polish (Brasso, Use only on grain finish surfaces
Goddard’s S/S Cleaner, Bar and work in direction of grain as
Keepers Friend) or a light non- slight scratching will occur.
metallic abrasive pad. Dura glit.
There are also products on the market which help to reduce the marks left by fingers and hands one of which is 3m’s
stainless steel cleaner, also of help is baby oil very lightly applied to the surface.
Product description:
Swift are wall mounted 3£ lever bib taps chrome plated
This tap is WRAS approved.
PANTRY
• Inset installation
• Unpolished (BA)
• External dimensions: 780 x 435 mm.
• Bowl dimensions: 368 x 338 x 146 mm
• 1 ½” valve hole & overflow
• Base units: 45 cm
• Packaging: Cardboard / Pallet
• Optional accessories:
• 1 ½” basket waste & overflow.
COD. 61001300
Code: 10133005
EAN: 8421152118184
WASTE ROOM
SAN-702
Technical specifications:
The automatic behind mirror mounted soap dispenser is made of plastic (bottle) stainless steel (support), and the nozzle with a chrome plated finish. The soap dispenser is activated by sensor located in the base. It
can be filled with different viscosity of soap solutions. Powered by IP67 Battery box or 12V transformer. The total dimensions of the dispenser are 360 x 160 x 120. The soap dispenser model is GW13 19 06 02,
manufactured by GENWEC WASHROOM S.L. ‐ Av. Joan Carles I, 46-48 ‐ ES 08908 L´Hospitalet de Llobregat ‐ Barcelona (SPAIN). www.genwec.com.
Technical characteristics
Product specifications
AC Adapter: 110-220V
Ambient temperature: 1-40ºC
Humidity: Max 90RH
Soap volume: <1.5ml
Soap viscosity: 100~3800 cPs
Bottle volume: 1000ml
Optional DC batteries power (please consult with Genwec).
GENWEC WASHROOM S.L. reserves the right to modify and/or rectify the products and their specifications without prior notice
Dimensions: ± 3%
Reviewed by: GWC_v2 (02/2021)
SOAP DISPENSERS GW13 19 06 02 Behind mirror automatic soap dispenser
Cleaning: A cotton cloth slightly dampened in a soapy solution is recommended. Then dry off. Do not use any strong chemicals or cleaning agents that can be dangerous to children.
GENWEC WASHROOM S.L. reserves the right to modify and/or rectify the products and their specifications without prior notice
Dimensions: ± 3%
Reviewed by: GWC_v2 (02/2021)
SAN-703
Product description
Behind mirror paper towel dispenser
Material: AISI 304 Stainless steel
Capacity: 400 C-fold or multi-fold paper hand towels
Finish: Brushed
Technical specifications:
Paper towel dispenser for mounting behind mirror is made in AISI 304 stainless steel with a brushed finish cover. Towel dispenser will dispense paper towels without the use of special adaptors. When correctly
installed only the paper towel tray is visible. Unit is loaded from the base self-closing panels of the paper towel tray. It has the capacity of the paper dispenser is 400 C-fold or multi-fold paper towels. The
dimensions of the dispenser are 358 x 120 x 350 mm. The paper dispenser model is GW03 28 04 01, manufactured by GENWEC WASHROOM S.L. ‐ Av. Joan Carles I, 46-48 ‐ ES 08908 L´Hospitalet de Llobregat ‐
Barcelona (Spain). www.genwec.com.
Technical characteristics
Product specifications
GENWEC WASHROOM S.L. reserves the right to modify and/or rectify the products and their specifications without prior notice.
Dimensions: ± 3%
Reviewed by: MG_V2 (02/2021)
PAPER DISPENSERS GW03 28 04 01 Behind mirror paper towel dispenser
Cleaning: A cotton cloth slightly dampened in a soapy solution is recommended. Then dry off. Do not use any strong chemicals or cleaning agents that can be dangerous to children.
GENWEC WASHROOM S.L. reserves the right to modify and/or rectify the products and their specifications without prior notice.
Dimensions: ± 3%
Reviewed by: MG_V2 (02/2021)
SAN-704 Behind Mirror Hand Dryer
Product description
Automatic sensor operated.
1.5mm stainless steel cover
Brushed finish
Protection grade IPX3
Efficient hand dryer: minimum consumption/drying 10s. aprox.
60 sec antivandalic automatic shut off (sense again after 2 sec)
Heavy duty for high traffic usage
ADA Compliant (100mm thickness)
Technical specifications:
The Genwec Slim hand dryer is manufactured in Stainless steel AISI 304 with 1.5 mm thickness and a brushed finish. The hand dryer is automatically activated by its infrared sensor and deactivates 2 seconds after
the hands are removed or after 60 seconds continuous work (antivandalic shut off). The air comes out by a lineal system of holes that assure an efficient distribution of the air. The motor voltage/frequency is 220-
240V, 35.000 r/min. The hand dryer offers the possibility to turn on or off the heating element with a switch in the hand dryer. The air speed reaches 342 km/h or 95m/s on maximum speed which facilitates a
drying time around 10 seconds. At maximum speed, the hand dryer has a total power of 400 -950W. The sound level at 2m distance is maximum 75 dB. The total measures of the hand dryer are 275x300x100 mm,
with a total weight of 4.5 kg. The product code is GW01 33 04 01, manufactured by GENWEC WASHROOM S.L. ‐ Av. Joan Carles I, 46-48 ‐ CP.: 08908 L´Hospitalet de Llobregat - Barcelona. www.genwec.com
Technical characteristics
Electrical specifications
La secadora de manos por aire caliente está formada porMechanical
una carcasa despecifications
una sola pieza fabricada en ABS en cuya parte inferior se ajusta una rejilla de policarbonato, y una base, también fabricada en ABS,
que funciona como soporte de la evoluta‐tobera fabricada en termoplástico ignífugo. El conjunto carcasa‐base que conforma la secadora se une a la pared con 4 agujeros, diámetro de la broca de 8mm. La secadora
Voltage: 220‐240 V
se activa por un sensor Air speed: 95 m/s – 342 km/h
Frequency: 50/60 Hz infrarrojo electrónico y automáticamente se apaga después que las manos se hayan retirado del campo del sensor. El motor, situado en el centro de la evoluta, es de del tipo universal sin
escobillas, 2800 r.p.m. La secadora da un caudal de aire Sound
de 4000level at 2m:
l/min (24075
m3dB
/h) a una velocidad de 65 km/h. El caudal fluye mientras el usuario siga utilizándolo. La secadora tiene una potencia total de 2050W a
Total power: 400 - 950W
Cover: Stainless Steel AISI 304 – 1.5mm thickness
230V con
Motor un consumo
power: 400 W máximo de 9A. El nivel sonoro a 2 metros es de 60 dB. El Índice de protección contra proyecciones es IPX1. Las dimensiones totales de la secadora de manos por aire caliente son de
Hot and cold switch
Rotor speed:
El modelo de35.000 r/min.
secadora de manos es GW01 22 01 04, fabricado por GENWEC WASHROOM S.L. ‐ Av. Joan Carles I, 46-48 ‐ c.p: 08908 L´Hospitalet de Llobregat ‐ Barcelona. www.genwec.com.
Protection grade: IPX3
Automatic turn off: 60s.
GENWEC WASHROOM S.L. reserves the right to modify and/or rectify the products and their specifications without prior notice.
Dimensions: ± 3%
Reviewed by: MG_V1 (02/2021)
HAND DRYERS GW01 33 04 01 Slim hand dryer stainless steel brushed
Cleaning: A cotton cloth slightly dampened in a soapy solution is recommended. Then dry off. Do not use any strong chemicals or cleaning agents that can be dangerous to children.
GENWEC WASHROOM S.L. reserves the right to modify and/or rectify the products and their specifications without prior notice.
Dimensions: ± 3%
Reviewed by: MG_V1 (02/2021)
SAN-714 Deck Mounted Soap Dispenser
Product description
Counter mounted soap dispenser
Head material: AISI 304 Stainless steel, polished
Shank material: Black ABS
White polyethylene container
Safety lock
With push pump
Container capacity: 1 litre
Technical specifications:
This counter mounted soap dispenser consists of a white container made of blow moulding polyethylene, an AISI 304 stainless-steel head with a polished finish and a shank made of black ABS. The container holds
up to 1 litre of liquid soap. The container is filled from the top of the dispenser by unfastening the top piece of the push pump with the tool provided for this purpose. The push pump is operated manually by
pressure. The dimensions of the dispenser are 400 x 83 x 127 mm, and its net weight is 0.4 kg. The dispenser is installed by drilling a Ø28 mm hole on the mounting surface. It can be filled with vegetable or
synthetic soap. The soap dispenser model is GW04 10 01 00, manufactured by GENWEC WASHROOM S.L. ‐ Av. Joan Carles I, 46-48 ‐ c.p: 08908 L´Hospitalet de Llobregat ‐ Barcelona. www.genwec.com.
Technical characteristics
Product specifications Packaging specifications
• Diameter of the counter hole: 28 mm • Type of individual package: Single cardboard box with a
• Spout length: 127 mm plastic bag
• Dispenser height: 60 mm
• Stem height: 93 mm
• Container height: 198 mm
• Diameter of the trim: 51 mm
• Head material: AISI 304 Stainless steel, polished
• Stem material: Black ABS plastic
• Container material: white polyethylene
• Capacity: 1 litre
GENWEC WASHROOM S.L. reserves the right to modify and/or rectify the products and their specifications without prior notice
Dimensions: ± 3%
Reviewed by: GWC_v2 (06/2019)
SOAP DISPENSERS GW04 10 01 00 1,000 ml soap dispenser
Cleaning: A cotton cloth slightly dampened in a soapy solution is recommended. Then dry off. Do not use any strong chemicals or cleaning agents that can be dangerous to children.
GENWEC WASHROOM S.L. reserves the right to modify and/or rectify the products and their specifications without prior notice
Dimensions: ± 3%
Reviewed by: GWC_v2 (06/2019)
SAN-719
Product description
Technical specifications:
900 mm AISI stainless steel grab bar to be installed in vertical or horizontal position. The tube has an outside diameter of 32 mm with a thickness of 1,5 mm, bended on both ends 90º. Mounting flanges are
manufactured in AISI 304 stainless steel with 2.5 mm thickness and 76,9 mm de diameter and are fixed to the ends of the bar using M10 screws. Mounting flanges have three holes for wall attachment. Snap flange
covers are manufactured in AISI 304 stainless steel with 0,5mm thickness and 77,6 mm diameter. Each cover snaps over mounting flange to conceal mounting screws. Clearance between the grab bar and wall is
43mm. The assembled unit has suitable resistance to corrosion. The grab bar is fixed to the wall by means of 6 nylon wall plugs (8X50) and AISI 304 stainless steel screws (5X60). Grab bar will support loads in excess
of 120Kg if properly installed. The grab bar code is GW11 05 04 01 manufactured by GENWEC WASHROOM S.L. – Av. Joan Carles I, 46-48 08908 L´Hospitalet de Llobregat.
Technical characteristics
Product specifications
GENWEC WASHROOM S.L. reserves the right to modify and/or rectify products and their specifications without prior notice.
Measures: ±3%
Revised by: EJO_V1 (03/2015)
GRAB BARS GW11 05 04 01 Satin grab bar 900 mm
GENWEC WASHROOM has electrical isolation kits for all grab bars manufactured in stainless
steel. The kit code for related grab bar is GW11.01.90.00 (2 units).
Cleaning: A cotton cloth slightly dampened in a soapy solution is recommended. Then dry off.
GENWEC WASHROOM S.L. reserves the right to modify and/or rectify products and their specifications without prior notice.
Measures: ±3%
Revised by: EJO_V1 (03/2015)
SAN-719
Product description
Technical specifications:
600 mm AISI stainless steel grab bar to be installed in vertical or horizontal position. The tube has an outside diameter of 32 mm with a thickness of 1,5 mm, bended on both ends 90º. Mounting flanges are
manufactured in AISI 304 stainless steel with 2.5 mm thickness and 76,9 mm de diameter and are fixed to the ends of the bar using M10 screws. Mounting flanges have three holes for wall attachment. Snap flange
covers are manufactured in AISI 304 stainless steel with 0,5mm thickness and 77,6 mm diameter. Each cover snaps over mounting flange to conceal mounting screws. Clearance between the grab bar and wall is
43mm. The assembled unit has suitable resistance to corrosion. The grab bar is fixed to the wall by means of 6 nylon wall plugs (8X50) and AISI 304 stainless steel screws (5X60). Grab bar will support loads in excess
of 120Kg if properly installed. The grab bar code is GW11 03 04 01 manufactured by GENWEC WASHROOM S.L. – Av. Joan Carles I, 46-48 08908 L´Hospitalet de Llobregat.
Technical characteristics
Product specifications Packaging specifications
GENWEC WASHROOM S.L. reserves the right to modify and/or rectify products and their specifications without prior notice.
Measures: ±3%
Revised by: EJO_V1 (03/2015)
GRAB BARS GW11 03 04 01 Satin grab bar 600 mm
GENWEC WASHROOM has electrical isolation kits for all grab bars manufactured in stainless
steel. The kit code for related grab bar is GW11.01.90.00 (2 units).
Cleaning: A cotton cloth slightly dampened in a soapy solution is recommended. Then dry off.
GENWEC WASHROOM S.L. reserves the right to modify and/or rectify products and their specifications without prior notice.
Measures: ±3%
Revised by: EJO_V1 (03/2015)
SAN-706 Undercounter Counter Waste Bin
WASTEPAPER BINS GW06 18 04 01 Under counter waste bin
Product description
Technical specifications:
Under counter waste bin. The product consists of a main square waste structure with two hinges to fix the plastic bag, and 1 front finger pull to easy take out the bin. The main structure is manufactured in folded
0,8 mm thickness AISI 304 stainless steel. On the sides there are two runners to be fixed below the counter using 6 screws (included). The product has a total measures of 458 x 305 x 152 mm. The wastepaper bin
model is GW06 18 04 01, manufactured by GENWEC WASHROOM, S.L. ‐ Av. Joan Carles I, 46-48 ‐ 08908 L´Hospitalet de Llobregat, Barcelona (SPAIN). www.genwec.com.
GENWEC WASHROOM S.L. reserves the right to modify and/or rectify the products and their specifications without prior notice
Dimensions: ± 3%
Reviewed by: MG (05/2020)
WASTEPAPER BINS GW06 18 04 01 Under counter waste bin
Cleaning: A cotton cloth slightly dampened in a soapy solution is recommended. Then dry off. Do not use any strong chemicals or cleaning agents that can be dangerous to children.
GENWEC WASHROOM S.L. reserves the right to modify and/or rectify the products and their specifications without prior notice
Dimensions: ± 3%
Reviewed by: MG (05/2020)
SAN-710 Cabinet Concealed Toilet Brush
Product description
Toilet brush
Material: AISI 304 Stainless steel
Finish: Polished
Technical specifications:
The toilet brush consists of one exterior polished bowl in stainless steel and the toilet brush set. The toilet brush set consists of a handle with a lid, made of AISI 304 stainless steel, and a brush head. The set is fitted
in the exterior brush bowl. The assembled set has a polished finish that provides it an appropriate resistance against corrosion. There is the possibility to anchor the product to a brick wall by means of a special
piece, 2 nylon wall plugs and 2 screws (included). The overall dimensions of the product are 363 x Ø76,5 mm. The accessory model is GW05 28 04 02, manufactured by GENWEC WASHROOM S.L. - Av. Joan Carles I,
46-48 08908 L’Hospitalet de Llobregat, Barcelona (Spain)
Technical characteristics
Product specifications Packaging specifications
AISI 304 stainless-steel toilet brush Type of individual package: Individual cardboard box and bubble wrap
The metal parts have a polished finish that provides them
an appropriate resistance against corrosion
GENWEC WASHROOM S.L. reserves the right to modify and/or rectify the products and their specifications without prior notice
Dimensions: ± 3%
Reviewed by: CSS_v3 (08/2018)
WASHROOM ACCESSORIES GW05 28 04 02 Toilet brush
Cleaning: A cotton cloth slightly dampened in a soapy solution is recommended. Then dry off.
GENWEC WASHROOM S.L. reserves the right to modify and/or rectify the products and their specifications without prior notice
Dimensions: ± 3%
Reviewed by: CSS_v3 (08/2018)
SAN-711 Cabinet Concealed Waste Bin
Product description
Technical specifications:
7 litres wall mounted waste bin made of AISI 304 stainless steel plate. The edges from the top and the bottom are bended to provide a higher security during the use and to avoid injuries. The product is fixed to the
wall with four screws. The bin has a satin finish that ensures adequate resistance to corrosion. The product has a total measures of 229x270x125 mm. The wastepaper bin model is GW06.13.04.01, manufactured by
GENWEC WASHROOM, S.L. ‐ Av. Joan Carles I, 46-48‐ ES 08908 L´Hospitalet de Llobregat – Barcelona (Spain). www.genwec.com.
Technical characteristics
Main body AISI 304 stainless steel plate Individual packaging: Individual carton
Brushed finish Individual packaging measures: 290 x 140 x 260 mm
Capacity 7 litres Product measures: 229 x 270 x 125 mm
Product weight: 1,50 kg
Carton units: 1
Units per box: 6
Box weight: 9,0 kg
Palet units: 72 (*)
GENWEC WASHROOM S.L. reserves the right to modify and/or rectify the products and their specifications without prior notice
Dimensions: ± 3%
Reviewed by: CSS_v2 (12/2017)
WASTEPAPER BINS GW06 13 04 01 Wall mounted waste bin 7L
Cleaning: A cotton cloth slightly dampened in a soapy solution is recommended. Then dry off. Do not use any strong chemicals or cleaning agents that can be dangerous to children.
GENWEC WASHROOM S.L. reserves the right to modify and/or rectify the products and their specifications without prior notice
Dimensions: ± 3%
Reviewed by: CSS_v2 (12/2017)
SAN-712 Cabinet Concealed Paper Dispenser
PAPER DISPENSERS GW03 02 04 01 Jumbo INOX 304 paper dispenser
Product description
Material: AISI 304 Stainless steel
Finish: Brushed
Spool roll type 250/300 m
Content viewer
Safety lock
Technical specifications:
The industrial hygienic paper dispenser is made up of a cover and support that is attachable to a wall. Both the wall mount and the cover, which includes a content viewer, are made in AISI 304 stainless steel with a
brushed finish. The rolls are replaced by inserting a key in the slot on the front of the dispenser and turning it 90º in order to lift the cover and access the spool. The core has rubber rings to fix the paper roll. The
type of paper used is a 250/300 m roll. The dispenser is fixed to the wall by means of screws, with universal wall plugs for brick walls, located on the product's wall mount. The paper dispenser model is GW03 02 04
01, manufactured by GENWEC WASHROOM S.L. ‐ Av. Joan Carles I, 46-48 ‐ ES 08908 L´Hospitalet de Llobregat ‐ Barcelona (Spain). www.genwec.com.
Technical characteristics
Product specifications Packaging specifications
Type of material: AISI 304 Stainless steel • Type of individual package: Individual cardboard box and
Finish: Brushed Cell Aire wrap.
Type of paper roll: 250/300 m. • Product dimensions: Ø275 x 121 mm
Safety lock
Content viewer
GENWEC WASHROOM S.L. reserves the right to modify and/or rectify the products and their specifications without prior notice
Dimensions: ± 3%
Reviewed by: JMPC_V3 (07/2019)
PAPER DISPENSERS GW03 02 04 01 Jumbo INOX 304 paper dispenser
Cleaning: A cotton cloth slightly dampened in a soapy solution is recommended. Then dry off. Do not use any strong chemicals or cleaning agents that can be dangerous to children.
GENWEC WASHROOM S.L. reserves the right to modify and/or rectify the products and their specifications without prior notice
Dimensions: ± 3%
Reviewed by: JMPC_V3 (07/2019)
SAN-713
Product description
Material: AISI 304 Stainless steel
Finish: Polished
Capacity: 1 hygienic roll
Technical specifications:
The single hygienic paper dispenser is made up of a wall mount and cylindrical roll holder. The wall mount is made in 0.8 mm thick AISI 304 stainless steel with a polished finish. The roll is replaced by applying
pressure on the cylindrical roll holder, dismounting it and adding the new roll. The cylindrical roll holder is made in chrome thermoplastic. The type of paper used is a domestic roll. The paper dispenser is fixed to
the wall by means of 2 screws located on the wall mount. The paper dispenser model is GW03 09 04 02, manufactured by GENWEC WASHROOM S.L. ‐ Av. Joan Carles I, 46-48 ‐ c.p: 08908 L´Hospitalet de Llobregat ‐
Barcelona. www.genwec.com.
Technical characteristics
Product specifications
GENWEC WASHROOM S.L. reserves the right to modify and/or rectify the products and their specifications without prior notice
Dimensions: ± 3%
Reviewed by: CSS_V1 (01/2016)
PAPER DISPENSERS GW03 09 04 02 Hygienic paper dispenser
Cleaning: A cotton cloth slightly dampened in a soapy solution is recommended. Then dry off. Do not use any strong chemicals or cleaning agents that can be dangerous to children.
GENWEC WASHROOM S.L. reserves the right to modify and/or rectify the products and their specifications without prior notice
Dimensions: ± 3%
Reviewed by: CSS_V1 (01/2016)
Al Wadi Building, Sheikh Zayed Road
P. O. Box 31840, Dubai
United Arab Emirates
Showroom Tel: +971 4 3356315
Office Tel: +971 4 3360601
Fax: +971 4 3360604
E-mail: gm@europeancorner-dubai.com
SPECIFICATION SHEET
Manufacturer SCHLOESSER-GERMANY
Description 1/2" X 1/2" ANGLE VALVE
Finish CHROME
Article Code 7111
www.europeancorner-dubai.com
Al Wadi Building, Sheikh Zayed Road
P. O. Box 31840, Dubai
United Arab Emirates
Showroom Tel: +971 4 3356315
Office Tel: +971 4 3360601
Fax: +971 4 3360604
E-mail: gm@europeancorner-dubai.com
SPECIFICATION SHEET
3/8"
Manufacturer SCHLOESSER-GERMANY
Description 1/2" X 1/2" ANGLE VALVE
Finish CHROME
Article Code 7111
71067106
www.europeancorner-dubai.com
PROJECT:
AL SAMRYA TRADING
SAMRYA QATAR 0 ERGA QATAR & NABINA CERAMIC
CONTRACTING CO.
SECTION - 6
PRODUCT CATALOGUE
Boutique Bathrooms
W W W. B Y C O C O O N .C O M
INDEX
20 John Pawson
42 Piet Boon
80 Cocoon Lab
82 Mono Collection
Transformation. A COCOON...
4
TEAM UP Our project division consist of an international &
6
PB SET25THERM - brushed inox
INSPIRED
BY DREAMS
SALINAS BATH - PEBBLE / PB SET24THERM - GOLD
professional rates.
9
THE COCOON to heat the water consumption, installing a
water consumption without compromising within the sector for sustainable design and
voluminous flow that never exceeds 5 litres steel tap collections, which are machined by
per minute, which is as kind to your pocket high-tech equipment, are certified for their
as it is to the environment. Using less water performance and safety by the most renowned
10
ADVANCED COCOON BOX
INSTALLATION SYSTEM
New revolutionary build-in system for John Pawson and Piet Boon tap ware collections.
The new system has some features which will enhance the ease of installation dramatically;
depth adjustable installation frames for ceramic cartridges are always reachable
super easy and accurate installation from the outside when walls are closed
made in the highest grade AISI 316 thus the colors even after years of use
stainless steel, in compliance with all optional NPT outlets for USA plumbing
installation
11
RAW MATERIALS
THAT GET
MORE BEAUTIFUL
WITH AGE
PB BASIN 60/90 - PEBBLE Photo by Thomas De Bruyne
COCOON and Studio Piet Boon share passion for craftmanship, timeless
design and natural materials that beautify with age. This mutual passion
13
SALINAS BATH - PEBBLE Photo by Thomas De Bruyne
Photo by Thomas De Bruyne
GEOMETRIC
SHAPES
CLEAR
TO OPERATE
Inspired by the simplicity and symmetry of
operated.
15
SIMPLICITY IS
THE ULTIMATE
SOPHISTICATION
LEONARDO DA VINCI
HANDCRAFTED Making timeless and sturdy design
lifetime.
18
PB COLUMN - CARRARA SUPREME Photo by Thomas De Bruyne
The production of our baths and made-to- We definitely believe that the decades of
measure basins takes place in our advanced combined experience will reflect in every
workshop in the Netherlands. single product we make.
19
JOHN
PAWSON
British architect
beauty.
20
JP COLUMN - NATURAL SAND
22
JOHN PAWSON
FOR COCOON
23
JP COLUMN - GRIGGIO EMPERADOR
Using pure and geometrical shapes, always The gracious perfect shapes and
honoring the ‘golden ratio’, John Pawson created spouts with extremely large radiuses
another timeless concept which will be enjoyed are typical for his timeless faucet and
24
JOHN PAWSON
BRUSHED INOX
TAP WARE COLLECTION
JP SET02.1
John Pawson designed a complete range of bespoke bathroom and kitchen tap
ware in the COCOON signature material AISI316 marine grade stainless steel.
JP SET24THERM JP 31
JP SET11.3
of the product. Just solid stainless steel with its brushed raw but clean
character, treated with NANO anti fingerprint coating.
27
JOHN PAWSON
BRUSHED GOLD
TAP WARE COLLECTION
JP 35.2 - GOLD
The gracious perfect round shapes and spouts with extremely large
30
JP SET23THERM.2 - GOLD
JP 30 - GOLD
JOHN PAWSON
DARK GREY
TAP WARE COLLECTION
JP SET01.1 - DARK GREY
The John Pawson by COCOON collection is available in 3 unique PVD colors especially
made for COCOON, all applied on the everlasting brushed steel and packed with
new technological features as NANO anti fingerprint coating, the latest water saving
35
JOHN PAWSON
NATURAL STONE
BATH & BASINS
Each object is a piece of art, a living legend. The timeless John Pawson signature
collection. The solid blocks of marble have been meticulously selected from the
famous stone quarries in Italy and crafted to perfection into items to be melted
38
JP BATH - PIETRA GRIGGIO / JP SET25THERM.2 - GOLD
JP BATH - NATURAL SAND
41
PIET
BOON
Designer
42
PB COLUMN - NATURAL LIGHT GREY / PB SET01 Photo by Thomas De Bruyne
PB 37 OUTDOOR SHOWER - COPPER Photo by Thomas De Bruyne
PB BASIN 60/90 L - PIETRA GRIGGIO / PB SET11 - COPPER Photo by Thomas De Bruyne
45
PIET BOON
BRUSHED INOX
TAP WARE COLLECTION
Stainless steel offers many advantages to the architectural and high demanding
48
PB SET01
PB 01
PB BASIN 60/12 - NATURAL GREY (BRUSHED) Photo by Thomas De Bruyne
The aesthetic appearance of this ECO friendly and LEAD FREE material provides
a modern and attractive base for our minimalistic tap collection designed by Piet
Boon. Available in brushed stainless steel, and the exclusive “Raw Copper“ and
PB 30
PB BATH - NATURAL LIGHT GREY / PB SET25THERM
51
PIET BOON
RAW COPPER
TAP WARE COLLECTION
PB BASIN 180/90 - PIETRA GRIGGIO / PB SET11 - COPPER Photo by Thomas De Bruyne
53
PB SET23 - COPPER
PB SET11 - COPPER
PB 04 - COPPER
Photo by Thomas De Bruyne
the stainless steel surface retaining and even increasing all of the
56
PB SET01 - COPPER
PB 30 - COPPER
PB SET21 - COPPER
59
PIET BOON
61
PB SET01- BLACK
PB 30 - BLACK
Photo by Thomas De Bruyne
63
PB SET11 - BLACK / PB BASIN 60/40 R - CARRARA SUPREME
PB SET01 - BLACK / PB BASIN 60/20 B - NERO MARQUINA Photo by Thomas De Bruyne
PB SET24 - BLACK
Photo by Thomas De Bruyne
66
PB SET01 - BLACK
PB 03
PIET BOON
69
PB BATH - CARRARA SUPREME Photo by Thomas De Bruyne
PB COLUMN - CARRARA SUPREME Photo by Thomas De Bruyne
PB BASIN 180/20 - CARRARA SUPREME / CABINET 180/20 - GREY
The basins are made from natural stone or solid surface while the
cabinets can have fronts of wood but are also available in the same
finishings as the basins.
72
PB BASIN 60/40 R - CARRARA SUPREME / CABINET 60/40 - GREY
76
PB BASIN 40/40 R -CARRARA SUPREME
MADE
TO LAST
A LIFETIME
COCOON LAB
items ideally engineered for the hospitality sector and larger project
investments in which budget and quality are the two main focus
80
ATLANTIS BATH - CHALK WHITE
MONO COLLECTION
& BATHROOM
ACCESSORIES
MONO SET01 / BOWL2.1 - CHALK WHITE
many years.
there.
83
MONO SET23
MONO SET24
MONO 01THERM
MONO SET01
COCOON baths and basins are casted from solid Being a homogenous surface it is
surface in our workshop in the Netherlands. Solid solid throughout. While being virtually
like appearance. Unlike stone, solid surface is scratched after years of use it can easily
non-porous. Making it easy to clean and resistant be refinished. Our successful made-to-
to stains, moisture and sunlight. This makes solid measure SOLID collection is available in
89
PB BASIN 180/90 DRAWERS - EARTH / PB SET11 - BLACK
91
ATLANTIS BATH - COAL Photo by Thomas De Bruyne
W W W. B Y C O C O O N .C O M
+ 3 1 2 0 8 0 8 7 5 5 7 / I N F O @ B Y C O C O O N .C O M
HOTELS & RESORTS
EDITION
CHECK-IN
WE INVITE YOU TO ENTER NOKEN
PORCELANOSA
ARQUITECTOS Y
DISEÑADORES HAN
ESTADO TRABAJANDO
JUNTO A NOKEN PARA
TRANSFORMAR
EL BAÑO
EN UNA EXPERIENCIA
MUTISENSORIAL ÚNICA
Patrik Schumacher Foster + Partners
MOCK UP ROOM SUPPLY AFTER-SALES SERVICE IN MORE COMPLETE EQUIPMENT INDIVIDUAL AND PERSONALIZED
SUMINISTRO DE HABITACIÓN PILOTO THAN 120 COUNTRIES FOR THE BATHROOM AFTER-SALES SERVICE
SAT LOCAL EN CUALQUIER PROVINCIA EQUIPAMIENTO COMPLETO POST-VENTA INDIVIDUAL
ESPAÑOLA Y EN MÁS DE 120 PAÍSES PARA EL BAÑO Y PERSONALIZADA
From our sales department we offer personal attention according to the Desde nuestro departamento comercial ofrecemos una respuesta personal y
EASY CLEANING needs of each client. acorde a las necesidades de cada cliente.
FÁCIL LIMPIEZA Our sales managers are frequently visiting their asigned geographical areas, to Nuestros comerciales recorren continuamente las zonas geográficas
personally attend the suggestions and concerns of our customers, following asignadas, para atender personalmente las sugerencias e inquietudes de los
up with them about the new upcoming products and services available at clientes, informándoles de los nuevos productos y servicios disponibles en
Noken. Noken.
On the other hand, customer and after-sales service, are responsible to solve Por otro lado, el departamento de soporte y atención al cliente, se ocupa de
their doubts and any issue that may arise during the budget process, orders, resolver las dudas e incidencias que pudieran surgir durante el proceso de
purchase, installation, etc. presupuesto, pedidos, compra, instalación, etc.
Noken contributes to the certification of sustainable hotels. This firm Noken contribuye a la certificación de hoteles sostenibles. La firma ayuda con
collaborates with its ECO bathroom equipment to comply with international su equipamiento de baño ECO al cumplimiento de normativas internacionales
guidelines, such as Leed and Breeam, Leadership in Energy & Environmental como Leed y Breeam, Leadership in Energy & Environmental Design y
Design and Building Research Establishment Environmental Assessment Building Research Establishment Environmental Assessment Method,
Method, respectively. These systems with points or stars measure criteria respectivamente. Estos sistemas de puntos o estrellas, miden criterios como
such as: innovation, the materials and the efficient energy and water use in la innovación, los materiales y el uso eficiente de energía y agua para otorgar
order to give hallmark scales. distintivos en escala.
Diverse global developers and world class hotels have already worked with Diversos promotores y hoteles a nivel mundial ya han trabajado con
Porcelanosa Bathrooms in relation to the compliance of these certificates, Porcelanosa Bathrooms para el cumplimiento de estas certificaciones, tanto
both in efficiency and savings and the added-value for its accommodations. a nivel de ahorro y eficiencia como del valor añadido que supone para sus
alojamientos.
Noken’s equipment helps buildings to save water and energy, as well as
obtaining efficient architecture certifications such as LEED and BREEAM. El equipamiento de Noken ayuda a los hoteles a ahorrar agua y energía, así
como a la obtención de certificaciones a la arquitectura eficiente como LEED
y BREEAM.
COLD-WATER OPENING MAXIMUM CHROME INTUITIVE SYSTEM 2 SIMULTANEOUS FUNCTIONS MIXER OR THERMOSTATIC SYMBOLS CAN BE CHANGED
On main position the tap only supplies cold water, preventing continued All Noken taps are protected by a double nickel and chrome layer. SISTEMA INTUITIVO 2 FUNCIONES SIMULTANEAS MEZCLADOR O TERMOSTÁTICA SIMBOLOS INTERCAMBIABLES
heaters use, reducing energy consumption and CO2 emissions. · 10 MICRON NICKEL · 0.25 MICRON CHROME
ECO-START MAXIMUM CHROME
En la posición central solo entra agua fría, evitando el uso continuo de Todas las Griferías de Noken están protegidas por una doble capa de níquel
calentadores y reduciendo el consumo energético y las emisiones de CO2. y cromo.
· 10 MICRON NICKEL · 0.25 MICRON CHROME FAST AND EASY INSTALLATION INTEGRATED SERVICE STOPS COMBINES WITH A WIDE RANGE HIGH PERFORMACE,
FÁCIL Y RÁPIDA INSTALACIÓN FÁCIL MANTENIMIENTO Y REPARACIÓN OF FUNCTIONS 800.000 CYCLES TESTED
COMBINA CON UNA AMPLIA ALTO RENDIMIENTO,
GAMA DE FUNCIONES 800.000 CICLOS PROBADOS
12L/min. -00% 5L/min. -55% The technology for the Touch & Feel shower is the outcome of the continuous
research carried out by the R & D Department to develop a system that
La tecnología para la ducha Touch&Feel ha sido resultado de investigaciones
continuas por el Departamento de I+D por desarrollar un sistema que facilite
standard - no ECO Kerox Cartridges tested for: facilitates the user’s daily life in the shower and meets the highest design el día a día del usuario en la ducha y cumpla con las más altas exigencias de
12L/min - 0% Cartridge life Requirements
estándar - no ECO Cartuchos Kerox ensayados requirements. To guarantee its quality and long lifetime, it has been subjected diseño. Para garantizar su calidad y garantizar una larga vida del producto, se
Vida del cartucho Exigencias de la norma
para:
ECO areator to pressure resistance tests up to 50 bar and resistance tests for push-buttons ha sometido a ensayos de resistencia de presión hasta 50 bares y tests de
aireador ECO 3,5L/min -70% 5L/min -55% 7L/min -40% EN817 70.000 cycles / ciclos + 175.000 cycles / ciclos
with more than 800,000 cycles. resistencia para los pulsadores de más de 800.000 ciclos.
Spray ECO ASME A 112.18.1 CSA B125.1 500.000 cycles / ciclos + 1.000.000 cycles / ciclos
2L/min -83% 3,5L/min -70% ø
Spray ECO
NOKEN CERAMIC ® EFFICIENT FLUSH NO SPLASH EASY CLEAN ANTI LIMESCALE NIPPLES ACERO AISI 304 FLOW RESTRICTOR FOR
A special coating makes the ceramic This technology, through two water The accurate conduction of the The elimination of the rim TETINAS ANTICAL ACERO AISI 304 WATER SAVING
solid and unalterable. Firing process outlets, clears the interior of the water on the surfaces of the bowl guarantees greater continuity of the LIMITADOR DE CAUDAL INCORPORADO
at 1250º. A total hygienic barrier entire toilet, increasing the efficiency of the toilet, with the right strength, toilet internal surfaces, facilitating its PARA EL AHORRO DE AGUA
creates a smooth and clean surface. of the product and reaching all confers an exceptional operation cleaning and less use of disinfectants.
NOKEN CERAMIC ® corners. without splashing. EASY CLEAN
Un esmalte especial que, gracias a EFFICIENT FLUSH NO SPLASH La eliminación de la brida garantiza
la cocción cerámica a 1250°, la hace Esta tecnología, gracias al difusor La conducción precisa del agua sobre mayor continuidad de las superficies
sólida e inalterable. Una barrera cerámico con 3 salidas de agua, las superfícies del bol del inodoro, del interior del inodoro, facilitando
totalmente higiénica que crea una limpia el interior del todo el inodoro con la fuerza adecuada, confiere así su limpieza y menor uso de
superficie lisa. sin necesidad de grandes caudales. un funcionamiento excepcional sin desinfectantes. SYSTEM PATENTED BY NK SECURITY VALVE EXTERNAL 2MM ULTRA-FINE PROFILE
salpicaduras. SISTEMA PATENTADO POR NOKEN VALVULA DE SEGURIDAD PERFIL ULTRAFINO DE
2MM EN EL EXTERIOR
FINISHES
ACABADOS
Resin and mineral shower trays Platos de ducha de resina y carga mineral
Their composition combines resins and natural minerals. It is essential for Su composición combina resinas y minerales naturales. Es fundamental para
the quality of the tray that the mineral material selection is good quality so la calidad del plato que la selección de materiales de la carga mineral sea de
that the final product offers the greatest guarantees, and also in the correct calidad para que el producto final ofrezca las mayores garantías, y además
proportion so that the shower tray maintains the lightness, flexibility, stability en una correcta proporción para que el plato de ducha conserve ligereza,
and tolerance. flexibilidad, estabilidad y tolerancia.
The Noken Mineral Stone and Mineral Stone Plus series have high lightness Las series de Noken Mineral Stone y Mineral Stone Plus tienen una alta ligereza
and little thickness; this does not affect either the resistance or the long- y espesor reducido, sin renunciar a resistencia y durabilidad. Están disponibles
lasting features. They are available in several finishes and colours, and they en varios acabados y colores, y permiten corte a medida al disponer de color FINISHES
can also be cut to size because of having the colour throughout their mass. en toda su masa. ACABADOS
Accessories
Complementos
Bath taps
Griferías de bañera
VITAE Lavabo suspendido / VITAE Estante / VITAE Estante bajo / VITAE Monomando de lavabo / VITAE
Espejo / VITAE Bañera / VITAE Columna de ducha / VITAE Inodoro suspendido / VITAE Pulsador cisterna
ME by MELIA / ZEN Plato de ducha
Dubai, Emiratos Árabes
PROJECT TECH Encimera / CURVE Monomando lavabo / FORMA Lavabo de encastre / SQUARE
Espejo 120x60 cm / TOUCH&FEEL Monomando de encastre baño/ducha con 2 salidas / NEPTUNE
WYNDHAM HOTELS & RESORTS SLIM RONDO Rociador / SLATE Plato de ducha / HOTELS Colgador / RONDO Pulsador cisterna
London, United Kingdom
ACRO-N Inodoro a tierra / ACRO-N Bidé / FORMA Lavavo de apoyo / ROUND Monomando lavabo caño
HOTEL VINCCI LA RÁBIDA alto / URBAN-C Portapapel / URBAN-C Colgador / ESSENCE-C Estante / TEC ROUND Columna de
Sevilla, Spain ducha termostática / SP ONE XL Bañera
TEC ROUND Columna de ducha termostática / ARQUITECT Lavabo de pie / ROUND Monomando de
INDEPENDENT HOTEL lavabo a pavimento / FORMA Espejo / LOUNGE SQUARE Bañera / ROUND Monomando de bañera a
Frankfurt, Germany pavimento / ROUND Monomando de lavabo encastre / ESSENCE-C Secatoallas / FORMA Inodoro a
pavimento
by photographer Porcelanosa Grupo
PROJECT WOOD Encimera / PROJECT WOOD Balda / FORMA Lavabo de apoyo / TONO Espejo /
LUXURY SUITES TONO Monomando lavabo caño alto / TONO Bañera / TONO Grifería de bañera a pavimento / TONO
New York, United States Termostática / TONO Inodoro suspendido / SMART LINE Pulsador cisterna
ACRO COMPACT Pack inodoro a tierra con salida orientable / HOTELS Monomando lavabo / HOTELS
HOTEL SILGAR 92 Grifería lavabo electrónica con 2 entradas de agua / HOTELS Colgador doble / HOTELS Espejo aumento
Sanxenxo, Spain con luz LED / HOTELS Toallero repisa / NK CONCEPT Secatoallas
LOUNGE Monomando lavabo / LOUNGE Batería instalación bañera / LOUNGE Colgador / LOUNGE
BEACH RESORT Rociador / LOUNGE Composición de ducha / ESSENCE-C Lavabo / LOUNGE Dosificador jabón /
Cancún, Mexico LOUNGE Toallero / LOUNGE Portapapel / ESSENCE-C Inodoro suspendido
‹ ï 𠧻¿®© ¿®®¿² ¬§ · ±ºº»®»¼º±®º¿«½»¬ ¿² ¼ë §»¿®º±®¿½½» ±®·» »¨ ½´«¼·² ¹ и ±¬±½»´´ ½±² ¬®±´´»¼ø߯«¿Í »»÷ôÍ Í Ì »´»½¬®±² ·½¿² ¼Ð»®º»½¬ Ì ·³ » ø߯«¿Ì ±«½¸ ÷³ ·¨ »® ô
‹ î §»¿® ©¿®®¿² ¬§ · ±ºº»®»¼º±®Ð¸ ±¬±½»´´ ½±² ¬®±´´»¼ø߯«¿Í »»÷ôÍ Í Ì »´»½¬®±² ·½¿² ¼Ð»®º»½¬Ì ·³ » ø߯«¿Ì ±«½¸ ÷³ ·¨ »®ò
‹ Î »º»®¬± ° ¿¹ » éçð óèï ï º±®½±³ ° ¿¬·¾·´·¬§ ¬¿¾´» ±º º¿«½»¬ ©·¬¸ © ¿ ¸ ¾¿ ·² ò
PROJECT:
AL SAMRYA TRADING
SAMRYA QATAR 0 ERGA QATAR & NABINA CERAMIC
CONTRACTING CO.
SECTION - 7
SAMPLE PICTURE
PROJECT:
AL SAMRYA TRADING
SAMRYA QATAR 0 ERGA QATAR & NABINA CERAMIC
CONTRACTING CO.
SECTION - 8
GSAS APPROVAL
PROJECT:
AL SAMRYA TRADING
SAMRYA QATAR 0 ERGA QATAR & NABINA CERAMIC
CONTRACTING CO.
SECTION - 9
CERTIFICATES
PROJECT:
AL SAMRYA TRADING
SAMRYA QATAR 0 ERGA QATAR & NABINA CERAMIC
CONTRACTING CO.
SECTION - 10
WARRANTY CERTIFICATES
PROJECT:
AL SAMRYA TRADING
SAMRYA QATAR 0 ERGA QATAR & NABINA CERAMIC
CONTRACTING CO.
SECTION - 11
AL SAMRYA TRADING
SAMRYA QATAR 0 ERGA QATAR & NABINA CERAMIC
CONTRACTING CO.
SECTION - 12
CR COPY
PROJECT:
AL SAMRYA TRADING
SAMRYA QATAR 0 ERGA QATAR & NABINA CERAMIC
CONTRACTING CO.
SECTION - 13
AL SAMRYA TRADING
SAMRYA QATAR 0 ERGA QATAR & NABINA CERAMIC
CONTRACTING CO.
SECTION - 14
GA DRAWINGS
PROJECT:
AL SAMRYA TRADING
SAMRYA QATAR 0 ERGA QATAR & NABINA CERAMIC
CONTRACTING CO.
SECTION - 15
INSTALLATION MANUAL