Professional Documents
Culture Documents
M52737SP
3-CHANNEL VIDEO PREAMPLIFIER WITH OSD MIXING, RETRACE BLANKING
DESCRIPTION
PIN CONFIGURATION (TOP VIEW)
The M52737SP is a semiconductor integrated circuit amplifies
video signals, having a 3-channel amplifier with a band width of
150MHz. The circuit also features the OSD mixing function. BLK IN (FOR OSD) 1 36 OSD ADJUST
The circuit is most useful with high-resolution displays that have VCC1 (B) 2 35 OUTPUT (B)
OSD, and its function are available for each channel, including OSD INPUT (B) 3 34 VCC2 (B)
blanking, OSD mixing, retrace blanking, wide-band amplification, SUB CONTRAST (B) 4 33 HOLD (B)
contrast control (main and sub), and brightness control. OSD IN (B) 5 32 NC
GND1 (B) 6 31 GND2 (B)
FEATURES VCC1 (G) 7 30 OUTPUT (G)
• Frequency band width: RGB................................150MHz (3V P-P) INPUT (G) 8 29 VCC2 (G)
M52737SP
OSD..............................................50MHz
Input :RGB.............................................................0.7V P-P (typ.) SUB CONTRAST (G) 9 28 HOLD (G)
OSD...............................................3.0VP-P min. (positive) OSD IN (G) 10 27 NC
BLK (for OSD)...............................3.0VP-P min. (positive)
Retrace BLK..................................3.0VP-P min. (positive) GND1 (G) 11 26 GND2 (G)
Output :RGB...........................................................4.5V P-P (max.) VCC1 (R) 12 25 OUTPUT (R)
OSD...........................................................4.5V P-P (max.)
INPUT (R) 13 24 VCC2 (R)
• To adjust contrast and OSD Adj, for each, two types of controls
are provided, main and sub. With the main control, the contrast or SUB CONTRAST (R) 14 23 HOLD (R)
OSD Adj of the 3-channels can be changed simultaneously. Sub OSD IN (R) 15 22 NC
controls are used to adjust the contrast of a given channel
individually. The control terminals can be controlled by applying a GND1 (R) 16 21 GND2 (R)
voltage of 0 to 5V. MAIN CONTRAST 17 20 BLK IN (FOR RETRACE)
• The DC power remains stable at the IC output terminal because CP IN 18 19 BRIGHTNESS
a feedback circuit is built in.
Outline 36P4E
APPLICATION
Display monitor
NC : NO CONNECTION
BLOCK DIAGRAM
OUTPUT (B) HOLD (B) GND2 (B) VCC2 (G) NC OUTPUT (R) HOLD (R) BLK IN (FOR RETRACE)
OSD ADJUST VCC2 (B) NC OUTPUT (G) HOLD (G) GND2 (G) VCC2 (R) NC GND2 (R) BRIGHTNESS
36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19
B B G G R R
AMP Hold AMP Hold AMP Hold
B B G G R R
Clamp Contrast Clamp Contrast Clamp Contrast
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
BLK IN INPUT (B) OSD IN VCC1 (G) SUB GND1 (G) INPUT (R) OSD IN (R) MAIN
(FOR OSD) SUB (B) CONTRAST(G) CONTRAST
SUB
VCC1 (B) CONTRAST(B) GND1 (B) INPUT (G) OSD IN (G) VCC1 (R) CONTRAST(R) GND1 (R) CP IN
1
MITSUBISHI ICs (Monitor)
M52737SP
3-CHANNEL VIDEO PREAMPLIFIER WITH OSD MIXING, RETRACE BLANKING
2
MITSUBISHI ICs (Monitor)
M52737SP
3-CHANNEL VIDEO PREAMPLIFIER WITH OSD MIXING, RETRACE BLANKING
Frequency T.P.35
b b b Vari- c a a
FC1 characteristics 1 T.P.30 5 − − -2 0 2.5 dB
(f=50MHz;maximum) SG1 SG1 SG1 able − − −
T.P.25
Frequency relative
∆FC1 characteristics 1 Relative to measured values above -1 0 1 −
(f=50MHz;maximum)
Frequency T.P.35
b b b Vari- c a a
FC1’ characteristics 1 T.P.30 5 − − -3 -2.0 3 dB
SG2 SG2 SG2 able − − −
(f=150MHz;maximum) T.P.25
Frequency relative
∆FC1’ characteristics 1 Relative to measured values above -1 0 1 −
(f=150MHz;maximum)
Frequency T.P.35
b b b Vari- c a a
FC2 characteristics 2 T.P.30 5 − − -3 0 3 dB
SG2 SG2 SG2 able − − −
(f=150MHz; maximum) T.P.25
Frequency relative
∆FC2 characteristics 2 Relative to measured values above -1 0 1 −
(f=150MHz; maximum)
T.P.35
b a a c a a
C.T.1 Crosstalk 1 (f=50MHz) T.P.30 5 5 − − − -30 -20 dB
SG1 − − − − −
T.P.25
T.P.35
b a a c a a
C.T.1’ Crosstalk 1 (f=150MHz) T.P.30 5 5 − − − -20 -15 dB
SG2 − − − − −
T.P.25
T.P.35
a b a c a a
C.T.2 Crosstalk 2 (f=50MHz) T.P.30 5 5 − − − -30 -20 dB
− SG1 − − − −
T.P.25
T.P.35
a b a c a a
C.T.2’ Crosstalk 2 (f=150MHz) T.P.30 5 5 − − − -20 -15 dB
− SG2 − − − −
T.P.25
T.P.35
a a b c a a
C.T.3 Crosstalk 3 (f=50MHz) T.P.30 5 5 − − − -30 -20 dB
− − SG1 − − −
T.P.25
T.P.35
a a b c a a
C.T.3’ Crosstalk 3 (f=150MHz) T.P.30 5 5 − − − -20 -15 dB
− − SG2 − − −
T.P.25
T.P.35
b b b Vari- Vari- b a a
Tr Pulse characteristics 1 T.P.30 5 − − 2.5 − nsec
SG3 SG3 SG3 able able SG4 − −
T.P.25
T.P.35
b b b Vari- Vari- b a a
Tf Pulse characteristics 2 T.P.30 5 − − 2.5 − nsec
SG3 SG3 SG3 able able SG4 − −
T.P.25
T.P.35
Clamp pulse threshold b b b b a a
V14th T.P.30 5 5 2 − 1.0 1.5 2.5 VDC
voltage SG5 SG5 SG5 SG4 − −
T.P.25
T.P.35
Clamp pulse minimum b b b b a a
W14 T.P.30 5 5 2 − 0.2 0.5 − µsec
width SG5 SG5 SG5 SG4 − −
T.P.25
Pedestal voltage T.P.35
b b b b a a
PDCH temperature T.P.30 5 5 2 − -0.3 0 0.3 VDC
characteristics1 SG5 SG5 SG5 SG4 − −
T.P.25
3
MITSUBISHI ICs (Monitor)
M52737SP
3-CHANNEL VIDEO PREAMPLIFIER WITH OSD MIXING, RETRACE BLANKING
T.P25 (30 or 35) is distorted. The voltage is called VOLR (VOLG or Waveform Output at T.P25
(Identical to output at T.P30 and T.P35.)
VOLB).
4
MITSUBISHI ICs (Monitor)
M52737SP
3-CHANNEL VIDEO PREAMPLIFIER WITH OSD MIXING, RETRACE BLANKING
3. Relative maximum gain ∆G is calculated by the equation below: 1. Set V4, V9, V14 and V17 to 3.0V. Other conditions are as given
3. Contrast control characteristics VCR1 and relative characteristics 1. Measuring conditions are as given in Supplementary Table.
∆VCR1 are calculated, respectively, by the equations below: 2. Measure the output at T.P25 (30 or 35) with a voltmeter.
The measured value is called VOR7 (VOG7 or VOB7), and is treated
VOR2 (VOG2, VOB2) [VP-P]
VCR1=20LOG as VB1.
0.7 [VP-P]
3. To obtain brightness control relative characteristics, calculate the
∆VCR1=VOR2/VOG2, VOG2/VOB2, VOB2/VOR2
difference in the output between the channels, using VOR7, VOG7
and VOB7.
VCR2 Contrast control characteristics (minimum)
∆VCR2 Contrast control relative characteristics (minimum)
∆VB1 =VOR7-VOG7 [V]
1. Set V17 to 1.0V. Other conditions are as given in Supplementary
=VOG7-VOB7
Table.
=VOB7-VOR7
2. Measure the amplitude output at T.P25 (30or 35). The measured
value is called VOR3 (VOG3 or VOB3), and is treated as VCR2.
VB2 Brightness control characteristics (typical)
3. Contrast control relative characteristics ∆VCR2 are calculated by
∆VB2 Brightness control relative characteristics (typical)
the equation below:
1. Measuring conditions are as given in Supplementary Table.
∆VOR2=VOR3/VOG3, VOG3/VOB3, VOB3/VOR3
2. Measure the output at T.P25 (30 or 35) with a voltmeter.
The measured value is called VOR7' (VOG7' or VOB7'), and is
VSCR1 Sub contrast control characteristics (typical)
treated as VB2.
∆VSCR1 Sub contrast control relative characteristics (typical)
3. To obtain brightness control relative characteristics (∆VB2),
1. Set V4, V9 and V14 to 4.0V. Other conditions are as given in
calculate the difference in the output between the channels,
Supplementary Table.
using VOR7', VOG7', and VOB7'.
2. Measure the amplitude output at T.P25 (30 or 35). The measured
value is called VOR4 (VOG4 or VOB4).
∆VB2 =VOR7'-VOG7' [V]
3. Sub contrast control characteristics VSCR1 and relative
=VOG7'-VOB7'
characteristics ∆VSCR1 are calculated, respectively, by the
=VOB7'-VOR7'
equations below:
VOR4 (VOG4, VOB4) [VP-P]
VSCR1=20LOG
0.7 [VP-P]
5
MITSUBISHI ICs (Monitor)
M52737SP
3-CHANNEL VIDEO PREAMPLIFIER WITH OSD MIXING, RETRACE BLANKING
6
MITSUBISHI ICs (Monitor)
M52737SP
3-CHANNEL VIDEO PREAMPLIFIER WITH OSD MIXING, RETRACE BLANKING
V14th Clamp pulse threshold voltage Oaj2 OSD adjusting control characteristics (minimum)
1. Measuring conditions are as given in Supplementary Table. ∆Oaj2 OSD adjusting control relative characteristics
2. Turn down the SG4 input level gradually, monitoring the output (minimum)
Measuring conditions and procedure are the same as described in
(about 1.8 VDC). Measure the top level of input pulse when the
Note 23, except that V36 is set to 0V.
output pedestal voltage turn decrease with unstable.
W14 Clamp pulse minimum width OSDth OSD input threshold voltage
1. Measuring conditions are as given in Supplementary Table.
Decrease the SG4 pulse width gradually, monitoring the output.
2. Reduce the SG6 input level gradually, monitoring output.
Measure the SG4 pulse width (a point of 1.5V) when the output
Measure the SG6 level when the output reaches 0V.
pedestal voltage turn decrease with unstable.
The measured value is called OSDth.
2. Measure the pedestal voltage at room temperature. 2. Make sure that signals are not being output synchronously with
3. Measure the pedestal voltage at temperatures of -20°C and 3. Reduce the SG6 input level gradually, monitoring output.
85°C. The measured value is called, respectively, P DC2 and Measure the SG6 level when the blanking period disappears.
4. PDCH=PDC1 - PDC2
PDCL=PDC1 - PDC3 HBLK Retrace BLK voltage
1. Measuring conditions are as given in Supplementary Table.
2. Monitoring to output at that time, read the level of retrace
OTr OSD pulse characteristics1
OTf OSD pulse characteristics2 blanking.
1. Measuring conditions are as given in Supplementary Table.
Control the MAIN OSD ADJUST(V36) in order that the amplitude HVth Retrace BLK input threshold voltage
of output signal is 3.0VP-P. Control the BRIGHTNESS(V19) in 1. Measuring conditions are as given in Supplementary Table.
order that the Black level of output signal is 2.0V. 2. Confirm that output signal is being blanked by the SG7 at the
2. Measure the time needed for the input pulse to rise from 10% to time.
90% (OTr1) and to fall from 90% to 10% (OTf1) with an active Monitoring to output signal, decreasing the level of SG7.
prove. Measure the top level of SG7 when the blanking period is
3. Measure the time needed for the output pulse to rise from 10% to disappeared.
90% (OTr2) and to fall from 90% to 10% (OTf2) with an active
prove.
4. Pulse characteristics Tr and Tf are calculated by the equations
below :
OTr (nsec)= (OTr2)2-(OTr1)2
OTf (nsec)= (OTf2)2-(OTf1)2
7
MITSUBISHI ICs (Monitor)
M52737SP
3-CHANNEL VIDEO PREAMPLIFIER WITH OSD MIXING, RETRACE BLANKING
INPUT SIGNAL
SG No. Signals
Sine wave with amplitude of 0.7VP-P (f=1MHz)
SGA
0.7VP-P
SG3
0.7VP-P
Pulses which are synchronous with standard video step waveform pedestal portion:
amplitude, 2.5VP-P; and pulse width, 0.5µs
SG4 2.5VP-P
0V
0.5µs 0.5µs
SG5
Standard
video step
waveform
4V
SG6
OSD BLK
and OSD
signals
0V
Pulses which are synchronous with standard video step waveform’s video portions: amplitude, 4.0V P-P; and pulse width, 15µs
4V
SG7
Retrace
BLK
signals
0V
Pulses which are synchronous with standard video step waveform’s video portions: amplitude, 4.0V P-P; and pulse width, 3µs
8
MITSUBISHI ICs (Monitor)
M52737SP
3-CHANNEL VIDEO PREAMPLIFIER WITH OSD MIXING, RETRACE BLANKING
5
The calculating of clamp pulse threshold voltage is by the method
1
pulse width is recommended
0 1 2 3 4 5 6
above 15kHz, 1.0µsec
above 30kHz, 0.5µsec Brightness Voltage (V)
18
–
+
BLK
(for OSD)
19
brightness 1
(1 to 5V)
9
MITSUBISHI ICs (Monitor)
M52737SP
3-CHANNEL VIDEO PREAMPLIFIER WITH OSD MIXING, RETRACE BLANKING
4
OSD output (VP-P)
0 1 2 3 4 5 6
Notice of application
⋅ Make the nearest distance between output pin and pull down
resister.
⋅ Recommended pedestal voltage of IC output signal is 2V.
10
MITSUBISHI ICs (Monitor)
M52737SP
3-CHANNEL VIDEO PREAMPLIFIER WITH OSD MIXING, RETRACE BLANKING
TEST CIRCUIT
SG7
560 a b
V36 560 560 V19
2.2µ 2.2µ 2.2µ SW20
36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19
VCC NC GND VCC NC GND VCC NC GND
M52737SP
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
SG4
A 100µ
a b
0.01µ SGA
SWA SG1 SG6
SG2
12V SG3 Units Resistance : Ω
SG5 Capacitance : F
TYPICAL CHARACTERISTICS
2403
POWER DISSIPATION Pd (mW)
2400
2000
1600
1200
800
400
11
MITSUBISHI ICs (Monitor)
M52737SP
3-CHANNEL VIDEO PREAMPLIFIER WITH OSD MIXING, RETRACE BLANKING
APPLICATION EXAMPLE
CRT
110V
DC CLAMP
BLK IN
(for retrace)
36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19
M52737SP
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
0.1µ
0 to 5V
0.1µ
0 to 5V
0.1µ
0 to 5V
0 to 5V
47µ 0.01µ 47µ 0.01µ 47µ 0.01µ
12
MITSUBISHI ICs (Monitor)
M52737SP
3-CHANNEL VIDEO PREAMPLIFIER WITH OSD MIXING, RETRACE BLANKING
DESCRIPTION OF PIN
Pin No. Name DC voltage (V ) Peripheral circuit of pins Description of function
VCC
2.5V
⋅Connected to GND if not
used.
GND
0.9mA
2 VCC (B-ch)
⋅Apply equivalent
7 VCC (G-ch) 12 −
voltage to 3 channels.
12 VCC (R-ch)
VCC
2k 2k
2.5V
CP
GND
0.24mA
VCC
4 Subcontrast 1.5k
(B)
9 Subcontrast ⋅Use at maximum 5V
2.5 2.5V
(G) 23.5k for stable operation.
14 Subcontrast
(R)
GND
VCC
13
MITSUBISHI ICs (Monitor)
M52737SP
3-CHANNEL VIDEO PREAMPLIFIER WITH OSD MIXING, RETRACE BLANKING
VCC
11k
17
Main ⋅Use at maximum 5V for
2.5 41k 2.5V
contrast stable operation.
GND
17
VCC
GND
VCC
20.3k
B-ch
19 Brightness −
G-ch
19
GND
VCC
GND
0.25mA
14
MITSUBISHI ICs (Monitor)
M52737SP
3-CHANNEL VIDEO PREAMPLIFIER WITH OSD MIXING, RETRACE BLANKING
VCC
1k
23 Hold (R)
⋅A capacity is needed on
28 Hold (G) Variable the GND side.
33 Hold (B)
0.2mA
GND
⋅A resistor is needed on
25 OUTPUT (R) the GND side.
30 OUTPUT (G) Variable Set discretionally to
35 OUTPUT (B) maximum 15mA,
50 Pin 25 depending on the
Pin 30 required driving capacity.
Pin 35
VCC
GND
15