Professional Documents
Culture Documents
The above Floor system has been Designed under the following Loads, Specifications and
Codes:
Design loads: Floor system in this job are designed for the following loads:
Design dead load on floor for 125 mm casting with floor finish 3.6 kN/m2
Design dead load on floor for partition wall 1 kN/m2
Design live load on floor 3.0 kN/m2
Wind speed 58.33 m/s
Wind exposure A
Load cases
1. EX & EX-, EZ & EZ-: Eartquake load from positive & negative X & Z-direction
respectively.
2. WX & WX-, WZ & WZ-: Wind load from positive & negative X & Z-direction respectively.
3. DL: Dead load with self weight of members and other superimposed Dead loads.
1. DL
2. DL+LL
3. DL + EX+
4. DL + EX-
5. DL + EZ+
6. DL + EZ-
7. 0.9 DL + EX+
8. 0.9 DL + EX-
9. 0.9 DL + EZ+
10. 0.9 DL + EZ-
11. 0.75 (DL + LL + EX+)
12. 0.75 (DL + LL + EX-)
13. 0.75 (DL + LL + EZ+)
14. 0.75 (DL + LL + EZ-)
15. DL + WX+
16. DL + WX-
17. DL + WZ+
18. DL + WZ-
19. 0.9 DL + WX+
20. 0.9 DL + WX-
21. 0.9 DL + WZ+
22. 0.9 DL + WZ-
23. 0.75 (DL + LL + WX+)
24. 0.75 (DL + LL + WX-)
25. 0.75 (DL + LL + WZ+)
26. 0.75 (DL + LL + WZ-)
Material Specifications
Below are BBS standard material specifications that will be used in the project. BBS reserves the right
to make material substitutions and changes in specifications as and when deemed necessary.
No. Components Specifications Strength
1 Built-up ASTM A572M /SS 400/Q345B Grade 345 Fy = 34.5 kN/cm2
Type1 ASTM A370
Tubes/Pipes JIS - G 3466 – STKR 490 Fy = 32.5 kN/cm2
2 Hot Rolled
Channels EN - 10025 S355JR Fy = 35.5 kN/cm2
3 Cold Formed ASTM A607/SS 400 Grade 40 Fy = 27.6 kN/cm2
JIS - G 3131 SPHC Fy = 27.6 kN/cm2
JIS - G 3132 SPHC
4 Wall, Roof & Liner Panel ASTM A792M Grade 345B: Coating AZ150/ Fy = 34.5 kN/cm2
ASTM A792M CS-B AZM150G/M2/
ASTM A792M Grade 50, PREPAINTED Al-Zn/
ALLOY-COATED
ASTM A653M SS Grade 345 Class 1: AZ Fy = 34.5 kN/cm2
5 Mezzanine Deck Panel Coating
ASTM A792 AZ150G/M2 AFP
Rods ASTM A615M Grade 420 Fu = 124 kN/cm2
Angles JIS - G 3101 - SS 400 Fu = 40.2 kN/cm2
6 X-Bracing
Cable ASTM – Fy = 119.7 kN/cm2
- Extra High Strength Class A Pu= 90 KN
7 Anchor Bolts ASTM A370 Fy = 27.6 kN/cm2[Dia
JIS G3101 – SS 400 >30 mm]
Fy = 24.84 kN/cm2
[Dia <= 30mm]
8 High Strength Bolts A325 M Type 1 Hot Dip Galvanized FU = 82.7 kN/cm2
DIN 933 Class 8.8 Zinc coated
9 Sag Rods ASTM A 36 M or DIN 933 Grade 4.6 Fy= 25.0 kN/cm2
Fy= Yield Strength ; Ft = Allowable Tensile Stress ; Fu= Ultimate Tensile Strength ;
Pu = Minimum Breaking Load.
Applicable codes: All buildings included in this proposal are designed in accordance with the
following codes that dictate the design and manufacture of pre-engineered steel buildings.
Loads on all buildings are applied in accordance with
1 International Building Code: 2006
International Code Council Inc. (ICC)
5203 Leesburg pike, Suit No 600, Falls Church, VA-22041
2 Bangladesh National Building Code (BNBC): 2006
3 ASCE-7-05
4 The 1996 edition of the Low Rise Buildings Manual
Metal Building Manufacturers Association Inc. (MBMA)
1300 Summer Avenue, Cleveland, Ohio 44115, USA
Bolt Strength:
Allowable capacity of Anchor Bolt
ASTM A36
Bolt Fy 248.2 Fu 400
dia (MPa) (MPa)
(mm) Fy (ksi) 35.989 Fu (ksi) 58
Tension (kN) Shear (kN)
20 47.14 25.14
25 73.66 39.29