Professional Documents
Culture Documents
TECHNICAL INFORMATION
FROM
M.Kawaguchi
Assistant General Manager,
Network and Communication Group
Engineering Department
Marine Electronics Division
2/2
Priority × A: Carry out immediately
B: Carry out at periodical inspection
C: Carry out upon client’s request
D: Information and news
1. Subject
CBG-2692 PS UNIT REPLACEMENT
2. Objective Equipment
JSS-296 MF/HF RADIO EQUIPMENT
(NAH-692 POWER AMPLIFIER)
Refer to the Objective ships list for JD-1269-03.
3. Outlines
Problem:
The coil (L3) on the PS UNIT (CBG-2692) in POWER AMPLIFIER (NAH-692) will be burned.
Countermeasure:
Exchange the PS UNIT (CBG-2692) in accordance with the CBG-2692 replacement procedures.
Be sure to send back the removed PS UNIT (CBG-2692) to the COMMUNICATION GROUP,
QUALTY ASSURANCE DEPARTMENT, MARINE ELECTRONICS DIVISION Via MARIN
SERVICE DEPARTMENT.
Note1: The replacement of NAH-692 and JSB-196GM changes into replacement of only the PS UNIT.
Note2: The PS UNIT is attached in the aluminum board.
Note3: The JRC code of the PS UNIT is CBG-2692.
4. Attached document
CBG-2692 PS UNIT replacement procedures
Objective ships list for JD-1269-03.
CBG-2692 PS UNIT 交換手順書
CBG-2692 PS UNIT Replacement procedures
-1-
(6) 天井板のビス 9 個を外します。
Remove 9 screws of the upper panel.
J1 (AC SW)
J4 (CDJ-2692)
J5 (CDJ-2692)
J3 (DC SW)
J2 (AUX PS)
J9 (BATT MONI)
J6 (ACCESSORY)
J7 (NFC)
J8 (JSB)
-2-
(9) 以下の端子のビスを外します。
Remove the screws of the
following terminals
(12) AC ケ ー ブ ル の ビ ス を
TB1(ACL)、TB2(CAN)端子か
ら外します。
Remove the screws of AC
cables from the TB1 (ACL)
and TB2 (ACN) terminals.
-3-
(13) 下記端子のビスを外す。
Remove the screws of the following terminals.
TB3 (L1)、TB4 (L1)、TB5 (T1-P)、TB6 (T1-P)、TB7 (T1-S)、TB8 (L2)、TB9 (T1-S)、
TB14 (T5-P)、TB18 (T5-S)、TB17 (L4)、 TB15 (T5-P)、TB16 (T5-S)、
TB19 (80V+) Red、TB20 (80V−) Blue
(14)IC 固定ビス、基板と放熱器
を固定しているビスを外す。
(取り外すビスの位置は次
ページを参照。)
Remove the screws from
IC and PCB. (Refer to the
next page for the position
of the screws to remove.)
-4-
下図のビスを取り外すします。(55 本)
Remove the screws of the following figure. (55 screws)
-5-
(15) 基板を外し、放熱器上に残った
取付足(スペーサ)を全て外す。
Remove the spacers from the
radiator.
取付足
Spacer
(16) 交換用基板を取り出す。
Prepare the new PCB.
(17) 交換用基板の事前準備として
本体放熱器との固定用ビスを
ピンセット等で、予め挿入して
おく。(使用するビスの長さは
次 ペ ー ジ の 図 参 照 )
For the easy assemble, insert
the screws each fixing points
before assemble.
(Refer to the next page to use
proper screws.)
-6-
図示の個所のネジは 本体の放熱器と確実に固定する事。 (計 18 本)
Fix with radiator, using proper screws. (18 screws)
-7-
(19) 交換用基板を本体に入れます。
Attach the new PCB on the radiator
with care.
.
(20) 本体放熱器と交換用基板を固定しま
す。
Tighten all screws on the PCB and
IC to the radiator.
CAUTION
プリント板の固定には 18 本全てのビスを使用してください。少ないビスでの
固定は故障の原因となります。
Use all 18 screws for fixation of the PCB. Fixation on a few screws may
lead to malfunction.
-8-