Professional Documents
Culture Documents
a. 1200-1250 psi
b. 1400-1500 psi
c. 600-750 psi
d. 2000- 3000 psi
A. the weight of the drill string multiplied by the depth of the hole
B. the work needed to move one ton over a one mile distance
C. the maximum drawworks capacity
D. the depth of the hole divided by the weight of the string.
15. Which size of Annular BOP will be used in Drilling 17 ½” hole section
a)20 ¾” b) 21 ¼” c) 20 ¼” d) Either A or B e) None of the above
16. TFA is a commonly used term in bit hydraulic. TFA stands for
…………………………………………
17. The 4 way control valve in a BOPCU should be always placed in either
a) open position
b) Close position
c) Neutral postion
d) Either A or B
18. If a Ram BOP is installed in a wellhead with upside down (inverted postion)
which seal will not function
a) Top seal b) Bonnet seal c) Ram packer d) All of the above
19. Which size of Grapple will be used in an overshot if the top of the FISH is a 2
7/8” tubing coupling
a) 2 7/8” b) 3.668 c) 3.875 d) 3.25
20.
22. While Drilling Stand pipe Pressure 2500 psi at 80 spm (APL =620 psi).Mud
Weight in use 12 ppg. MD =3975 ft
A. 15.0 ppg
B. 12.5 ppg
C. 12.0 ppg
D. 13.5 ppg
31. The minimum tensile strength for API Casing Grade-J55 is—
A. 55,000 psi.
B. 80,000 psi.
C. 75,000 psi.
D. 100,000 psi]
32. The device used to move the casing around obstructions or ledges in the
hole is a—
A. float collar.
B. baffle collar.
C. centralizer.
D. guide shoe.
33. If a Leak off Test was carried out when using a 10.3ppg mud casing shoe
3000 m., and the applied, surface pressure that leak-off occurred at was
1580psi.
(a) What is the Maximum Mud Weight that can be used without
incurring losses?
34. A vertical well is shut in after a kick. The pressure readings are as
follows:Shut in drill pipe pressure (SIDPP) = 4680 kPa Shut in casing pressure
(SICP) = 6150 kPa
What is the reason for the difference in the two pressure readings?
a) The influx is in the drill pipe
36.
Would it be good drilling practice to circulate and kill the well with the lower set
of 127 mmrams closed, when the drill string is in the hole?
a) Yes
b) No
37.
Can the inner choke valve be repaired if the well is shut in with the blind/shear
rams with no drill string in the hole?
a) Yes
b) No
38. What is the primary function of a weep hole (drain or vent hole) on a ram
type BOP?
a. To show that the ram body rubbers are leaking.
b. To show that the closing chamber operating pressure is too high.
c. To show that the mud seal on the piston rod is leaking.
d. To show that the bonnet seals are leaking.
39. Benefits derived from using a bottom plug in the cementing operation
include
A. wiping mud film from inside casing.
B. reducing slurry contamination.
C. preventing entry of air into slurry.
D. all of the above
45. At the start of a trip out of the hole for a bit change, the first 10 x 93 ft
stands of pipe are pulled from the hole dry with no fill up. Using the following
data calculate the reduction in bottom hole pressure?
A. 650 psi
B. 6 psi
C. 65 psi
D. 130 psi
46. Select the two things that are needed to accurately determine an Initial
Cicrulating Pressure?
47. At the start of a trip out of the hole for a bit change, the first 20 x 93 ft
stands of pipe are pulled from the hole wet with no fill up. Using the following
data calculate the reduction in bottom hole pressure?
A. 48 psi
B. 483 psi
C. 600 psi
D. 683 psi
48. The weight of 3000m of 10.5 ppf drill pipe in 10ppg mud (with buoyancy
Factor) is approximately
a. 65T
b. 40T
c. 52T
d. None of the above
A. True
B. False
53. The Drillers Method of Well Control normally requires how many
circulations to kill a well?
A. one circulation
B. two circulations (Reference Page 6-2)
C. three circulations
D. four circulations
C. The distance between the two flanges when installed with the studs
and the nuts tightened.
55.
56. Marsh funnel viscometer is used to measure:
a) Fluid loss
b) Cake thickness
c) Viscosity
d) Rheology
e) None of the above.
57.
Which valves need to be open to circulate mud through through the remote choke
and mud gas separator
59. Which one of the following is the first reliable indication that well is
flowing?
a) Increase in torque
b) Gas cut mud
c) Decrease in pump pressure
d) Increase in return flow
60.Pressure loss through the bit nozzles should be in the range of
a. 10% - 20% of the available surface pressure
b. 50% - 60% of the available surface pressure
c. 80%- 90% of the available surface pressure
d. 23 ½% - 33 ½% of the available surface pressure
63 High grade casings from N-80 onwards are not welded because casing
joint becomes weaker due to
a) Development of thermal stress concentration.
b) Ballooning effect on the casing body.
c) Occurrence of buckling of casing body.
d) None of above.
64. What is the specification of low drum clutch of e-1400 bhel draw works?
a) 38 VC 1200 b) 36 VC 1200
c) 30 VC 1200 d) 34 VC 1200
65. What is the air pressure requirement for bhel draw works clutches?
a) 110-120psi b) 120-130psi
c) 100-110psi d) 90-100psi
66. What is the function of an interlock valve in bhel draw works?
a) To prevent engaging of both clutches b) To engage lo clutch
c) To disengage hi clutch. d) To disengage hi
clutch
67. What is the drum size of e-1400 bhel draw works?
a) 52” long 28” diameter b) 52” long 26”
diameter
c) 50” long 28” diameter d) 54” long 30”
diameter
68. Vacuum degasser is a solid control equipment. True/False.
69. Cellar depth for a 4 stage well is
a) 1.25m b) 1.35m
c) 1.30m d) 1.20m
70. What does quick release valve does in bhel draw works?
a) It is a 3-way pressure controlled valve with open exhaust. Mainly
used in a pneumatic circuit to speed up the response time. b)
Permits flow of air in one direction.
c) It speeds the exhausting of air cylinders & other devices. d) Mainly a
directional control valve which controls a high pressure feed.
71. Vfd draw works are water cooled. True or false?
72. What is the bull line size of VFD Rigs?
a) 3” b) 2 3/8”
c) 2 ¾” d) 3 ¼”
73. Centrifuge is employed to removes cuttings of sizes lower than
a) <10µ b) <50µ
c) <500µ d) <100µ
74. Capacity of poor boy degasser depends on:
a) Liquid seal b) vent line
c) height of degasser d) inlet capacity of
degasser
75. What is the fleet angle of E-1400 rig in case of grooved drum?
a) 1.5-2° b) 0.5-1°
c) 1-2° d) 1-1.5°
76. How many mud tanks are there in E-1400 drilling rigs:
a) 6 b) 8
c) 7 d) 5
77. Which one of the following is NOT a warning sign when a kick may be
occurring?
a) Flow rate increase
b) Increased torque
c) Pit gain
d) Gas cut mud
78. What would you do if total loss occurs while drilling with water base
mud?
a) Continue drilling blind .
b) Stop drilling and fill the hole up with water
c) Stop drilling, shut – in the well and see what happens
82.
The load imposed on the drawworks is equal to ________ in the fast line
a. Tension
b. Compression
c. Friction
d. Shear
83.
Mud circulating pumps are used to circulate drilling fluid at desired
a. Depth
b. Volume
c. Pressure
d. Both b & c
84.
After drilling 9.5/8” casing shoe at 1876 m it was decided to carry out PIT
with existing mud weight of 69 pcf for equivalent mud weight of 84 pcf. What
is the BHP at the time of testing?
85.
86.
87.
a) Mud system.
b) Special lubricant stored by inbuilt mechanism.
c) Need no lubrication.
88.
a) Bingham fluid.
b) Thixotropic fluid.
c) Rheopectic fluid.
89.
90.
a) > 45 microns.
b) < 45 microns.
c) 20 – 45 microns.
91.
During normal drilling operation with a mud of specific gravity 1.3, the
specific gravity of discard mud from a Desilter is found to be 1.5. Is the
Desilter performing effectively?
a) Yes b) No.
92.
94.Pressure gradient = 0.65 psi / ft. What is the mud weight required to drill
this formation?
95.
96.
97.
98.
a) Retarders.
b) Accelerators.
c) Density reducing agent.
d)
99.
100.
101.
A 26” hole is being drilled. At 1200 feet TVD from surface the formation
pressure is exactly 601 psi. What is the formation pressure?
102.
To ensure that correct results are obtained from a leak-off test at the casing
shoe, a number of critical parameters have to be accurately observed,
measured and recorded. Select the critical parameters from the following list.
(Three answers).
103..The API has established guidelines for pipe classes in API RP7G. The
Premium class is summarized as follows:
Premium:- Allows drill pipe with a minimum wall thickness of 65%
with all wear on one side so long as the cross-sectional area is the not
more than 20% uniform wall reduction.
a. True
b. False
104.
While drilling ahead, partial losses are measured at 10 bbl/hr. A total power
failure occurs. What will be the reduction in BHP after 3 hrs if the hole
cannot be filled?
105.
a) The distance between the two flanges when installed with the studs and
the nuts tightened.
b) The internal diameter of the flange.
c) The total height of the two flange assembly.
d) The external diameter of the flange.
106.
Bit balling can:
a) Lower rop
b) Create more swabbing
c) Increase torque
d) All of the above.
107.
What is the reason for raising the Kelly to bring the first tool joint above the
rotary table when shut in a well?
a) To get sufficient sump between off bottom and bit during killing
operation.
b) Extend closing time to give shortest possible shut in.
c) Allow annular to close around drill pipe, because the annular is not
designed to seal around the Kelly.
d) Allow access to the lower Kelly cock and if required, remove the Kelly.
108.
After pulling 15 stands off bottom, you suspect fluid has been swabbed in. A
flow check shows the well is not flowing. Which of the following is the best
procedure to deal with this?
109.
110.
111.
a. SS-220
b. SS-46
c. W-40
d. HSD
116.
Why it is useful to count BPO (before pulling out) tubular.
a. To cross check the pipe tally
b. To count the working single
c. For back calculation
d. All of the above
117.
a. During tripping
b. During drilling
c. During casing
d. Both A & C
118.Trip tank is use during:
a. Coring
b. Drilling
c. Fishing
d. Tripping
119.
Fast end of the casing line is anchored with draw works by means of:
a. Tape wedge
b. Dead end anchor
c. Turn buckle
d. Crown pulley
121.
Which of the following are relevant to the drilling mine:
a. Mine vocational training
b. First Aid Training
c. Firefighting training
d. All of the above
122. Write Full forms of the following:
e. AV
f. DPR
g. BDF
h. BHP
i. CBL
j. UBHO
k. TPI
l. NPT
m. IWCF
n. TLC
123. What are the factors that determine rig selection:
a) Wind speed
b) Rack Back Weight
c) Depth of well
d) All of the above
TRUE/FALSE
124.
Closing systems of Surface BOPs should be capable of closing each ram
preventer and annular preventer upto 18.3/4” size within 60 seconds and
annular preventer above 18.3/4” within 90 seconds. a. True b. False
125.
For a soft formation tri-cone bit the cone offset is much more than that of a
bit for hard and abrasive formation. a. True b. False
126
Equivalent mud density is more effective in deep hole section than top hole
section. a. True b. False
127.
The pressure loss across bit nozzles for best performance is 70%. a. True b.
False
128.
For best results cement should be displaced at laminar flow rate. a. True b.
False
129.
In a weight indicator same dial can be used for different number of casing
string. a. True b. False
131.
Bit breaking for PDC bit is essential for its longevity. a. True b. False
132.
Any Floor 1.8 meters or more above ground level shall be guarded by a
standard railing at least 1 m high with toe board 0.15 m high. a. True b.
False
133.
Crews should not set the slips too hard. This causes slip dies to make deep,
sharp notches that form cracks in the drill pipe and eventually result in a
washout. a. True b. False
134.
Crews can prevent drill pipe damage from overused and worn slips, dies, and
bushings with more frequent and thorough inspections and maintenance. a.
True b. False
135.
After a missed stab, crews should pick up the pipe to stab again, rather than
kick the pin into the box. This can cause a false torque reading, under-
torqued connections, connection failures, and possibly a fishing job. a. True
b. False
136.
Crews should always use two tongs to break out connections. The use of only
one tong increases the risk of damage and resulting in bent pipe, coating
failure, and fatigue failure. a. True b. False
137.
BOP hydraulic oil can also be use in rotary table and swivel. a. True b. False
138.
Careful thread cleaning and fresh lubrication help longer drill pipe life. a.
True b. False
139.
Hole fill is necessary but casing fill up not required during casing run in
operation. a. True b. False.
140.
Filter cake thickness is more if fluid loss is more. a. True b. False
141.
Outside diameter of tool joints of G -grade drill pipe is more than the S-grade
a. True b. False
143.
144.In “Right lay, Lang lay” wire line, the strands and the individual wires in
each strand are wound in the opposite direction. a. True b. False
146.
Drill collars without slip recesses do not require safety clamp after putting on
hand slip and before releasing the elevators. a. True b. False
147.
Usually Drill pipe failures occur in the tool joints rather than in the body. a.
True b. False
148.
a) Brownish black
b) White
c) Transparent
d) Light yellow
27. Which of the following chemical is NOT used as a fluid loss control additive?
a. Starch
b. CMC
c. Bentonite
d. Pipe lax
28. Which of the following is not a Rheological property of mud-
a) Gel strength
b) Apparent viscosity
c) Yield value
d) Sand content
33.
Gamma ray- Casing Collar Locator is run prior to perforating
a. To neutralize radioactive source
b. To prevent explosion
c. To assure precise depth measurement
d. To centralize the gun