Professional Documents
Culture Documents
No : AP003164-G-SP-1300-0001
MUTINEER / EXETER FPSO Rev : 0
Piping Specification Page : 2 of 19
RECORD OF AMENDMENT
It is certified that the amendments listed below have been incorporated in this copy of the publication.
Property of Technip Oceania Pty Ltd. Copyright TECHNIP OCEANIA PTY. LTD.
All rights reserved
AP003164-G-SP-1300-0001r0 - W1440-P1-S-2100.doc
Doc. No : AP003164-G-SP-1300-0001
MUTINEER / EXETER FPSO Rev : 0
Piping Specification Page : 3 of 19
Property of Technip Oceania Pty Ltd. Copyright TECHNIP OCEANIA PTY. LTD.
All rights reserved
AP003164-G-SP-1300-0001r0 - W1440-P1-S-2100.doc
Doc. No : AP003164-G-SP-1300-0001
MUTINEER / EXETER FPSO Rev : 0
Piping Specification Page : 4 of 19
TABLE OF CONTENTS
1.0 GENERAL................................................................................................................ 5
1.1 Introduction .............................................................................................................. 5
1.2 Scope....................................................................................................................... 5
5.0 CERTIFICATION.................................................................................................... 17
5.1 General .................................................................................................................. 17
5.2 Type A Certificates................................................................................................. 17
5.3 Type B Certificates................................................................................................. 17
APPENDICES
Property of Technip Oceania Pty Ltd. Copyright TECHNIP OCEANIA PTY. LTD.
All rights reserved
AP003164-G-SP-1300-0001r0 - W1440-P1-S-2100.doc
Doc. No : AP003164-G-SP-1300-0001
MUTINEER / EXETER FPSO Rev : 0
Piping Specification Page : 5 of 19
1.0 GENERAL
1.1 Introduction
The Mutineer and Exeter fields are located in petroleum exploration permit WA-191-P, ca.
150km offshore North Western Australia in ca. 160m of water. Santos Ltd is the operator
of the permit area and shares petroleum rights within the permit area with partners Kufpec
Australia Pty Ltd (33.4%), Nippon Oil Exploration (Barrow) Pty Ltd (25%) and Woodside
Energy Ltd (8.2%). Allocation metering will be performed prior to co-mingling of the fields
on the FPSO.
The development consists of a disconnectable, permanently manned floating production
storage and offloading (FPSO) facility, with crude export via opportunity tankers.
The FPSO will be moored between the two fields, approximately 3km from Mutineer and
7km from Exeter. The development plan allows for future tie-back of near and infield
accumulations.
This specification defines the minimum technical requirements for the design, manufacture
and testing of piping for the Mutineer-Exeter Development.
1.2 Scope
• Specifying piping material classes and associated valve data sheets to be used in the
design of piping systems for all topsides and swivel pipework.
• Specifying the pressure and temperature limitations for each piping class
• Specifying the non-destructive testing requirements for the piping classes
• All instrument control piping downstream of the piping flange, block valve or monoblock
assembly
• Pipelines, risers, flowlines and sub-sea pipework
• Actuated instrument control valves
The requirements of the latest editions, of the following Codes and Standards shall be
complied with unless specifically noted otherwise within this Specification.
Property of Technip Oceania Pty Ltd. Copyright TECHNIP OCEANIA PTY. LTD.
All rights reserved
AP003164-G-SP-1300-0001r0 - W1440-P1-S-2100.doc
Doc. No : AP003164-G-SP-1300-0001
MUTINEER / EXETER FPSO Rev : 0
Piping Specification Page : 6 of 19
Property of Technip Oceania Pty Ltd. Copyright TECHNIP OCEANIA PTY. LTD.
All rights reserved
AP003164-G-SP-1300-0001r0 - W1440-P1-S-2100.doc
Doc. No : AP003164-G-SP-1300-0001
MUTINEER / EXETER FPSO Rev : 0
Piping Specification Page : 7 of 19
Publication No. 144 90/10 Copper Nickel Alloy Piping for Offshore Applications: Tubes –
Seamless and Welded (Sections 1 and 2)
Publication No. 145 90/10 Copper Nickel Alloy Piping for Offshore Applications: Flanges
– Composite and Solid (Sections 1, 2 and 3)
Publication No. 146 90/10 Copper Nickel Alloy Piping for Offshore Applications: Fittings
(Sections 1, 2, 3 and 6)
Publication No. 182 Specification for Integral Block & Bleed Valve Manifolds for Direct
Connection to Pipework
MSS SP 25 Standard Marking System for Valves, Flanges, Fittings and Unions
MSS SP 44 Steel Pipeline Flanges
3.0 ABBREVIATIONS
Abbreviation Explanation
µm micrometres
ABS Acrylonitrile Butadiene Styrene
API American Petroleum Institute
ASME American Society of Mechanical Engineers
ASTM American Society for Testing and Materials
BB Bolted Bonnet
BW Butt Weld
C Carbon
CA Corrosion Allowance
CE Carbon Equivalent
Cr Chromium
CS Carbon Steel
Cu Copper
CuNi 90/10 Copper Nickel
D Diameter
DN Nominal Diameter (in mm)
DPI Dye Penetrant Inspection
E Joint Quality Factor
EEMUA The Engineering Equipment & Material Users Association
EFW Electric Fusion Welding
EN European Norm
ENP Electroless Nickel Plating
EPDM Ethylene Propylene gasket material
FF Flat Face
FPSO Floating Production, Storage, Offloading
GOR Gas Oil Ratio
GRE Glass Reinforced Epoxy
HAZ Heat Affected Zone
HRC Rockwell Hardness C
Hv Vickers Hardness
m Metres
Property of Technip Oceania Pty Ltd. Copyright TECHNIP OCEANIA PTY. LTD.
All rights reserved
AP003164-G-SP-1300-0001r0 - W1440-P1-S-2100.doc
Doc. No : AP003164-G-SP-1300-0001
MUTINEER / EXETER FPSO Rev : 0
Piping Specification Page : 8 of 19
mm Millimetres
Mn Manganese
Mo Molybdenum
MPI Magnetic Particle Inspection
MSS Manufacturer’s Standardisation Society
N Newtons
NACE National Association of Corrosion Engineers
NDE Non Destructive Examination
Ni Nickel
NPT National Pipe Thread
ºC Celsius
OS&Y Outside Screw and Yoke
P&IDs Piping and Instrumentation Diagrams
PN Nominal Pressure (in barg)
ppm Parts per million
PRE Pitting Resistance Equivalent
PTFE PolyTetraFluoroEthylene (fluoroplastic)
Ra Roughness
RF Raised Face
RTJ Ring Type Joint
SAW Submerged Arc Welding
Sch Pipe Schedule (wall thickness)
SS Stainless Steel
SW Socket Weld
UN Unified National
UNC Unified National Coarse
UPVC Unplasticised PolyVinylChloride
UT Ultrasonic Testing
V Vanadium
WN Weld Neck
XS Extra Strong (pipe schedule)
XXS Double Extra Strong (pipe schedule)
4.1 General
Property of Technip Oceania Pty Ltd. Copyright TECHNIP OCEANIA PTY. LTD.
All rights reserved
AP003164-G-SP-1300-0001r0 - W1440-P1-S-2100.doc
Doc. No : AP003164-G-SP-1300-0001
MUTINEER / EXETER FPSO Rev : 0
Piping Specification Page : 9 of 19
Unconnected branch connections DN50 and smaller on reciprocating pump suction and
discharge lines shall be schedule XXS nipple (100mm long maximum) regardless of the
schedule specified in the Piping Class.
Piping systems connected to other systems or equipment with a higher design rating shall
have the higher rating for all components up to and including the first block valve in the
system of lower rating.
Screwed and socket weld piping connections are not permitted for hydrocarbon service
unless approval is obtained in writing from the Purchaser.
4.2 Pipe
All pipe shall be specified with the nominal size and schedule number per ASME B36.10.
Corrosion allowance shall be as per the process service requirements, given in the
relevant piping classes.
Pipe shall be seamless up to and including DN400 and SAW or seamless for DN450 and
larger (unless otherwise noted on the Piping Class). The longitudinal weld shall have a
minimum weld joint quality factor (E) of 0.95 (as defined by ASME B31.3).
Cold expansion, if used, shall be limited to 1% maximum strain. Piping shall be supplied
with bevelled ends as per ASME B31.3 / B16.5.
Where sour service requirements are specified, the maximum hardness of the finished
pipe shall be 22 HRC (250 Hv 10) per the requirements of NACE MR-01-75. Sulphur
content shall not exceed 0.01%.
All pipe shall be specified with the nominal size and schedule number per ASME B36.19.
All materials shall be in accordance with ASTM A312 (UNS S31603) type 316L, but with
type 316 properties. Addtionally, all type 316L piping and instrument tubing shall be
supplied with a minimum Molybdenum content of 2.5%.
Seamless pipe shall be supplied up to and including DN400. Welded or seamless pipe
can be used for sizes DN450 and larger. Welding procedures shall ensure that the
corrosion resistance of the weld metal and HAZ are equal or better than the parent
material. For DN200 and larger the pipe weld shall be 100% radiographed to meet the
requirements of ASME B31.3 Table 302.3.4(3a) for a joint quality factor of 1.00. All other
sizes shall have a minimum joint quality factor (E) of 0.85 as defined by ASME B31.3.
All pipe shall be supplied in the de-scaled, pickled, passivated and solution heat treated
condition.
CuNi pipe shall be a nominal 90/10 Cu-Ni-Fe composition complying with BS 2872 CN102,
EEMUA 146 or equivalent.
Pipe shall be supplied in the annealed condition. Dimensions shall be in accordance with
EEMUA publication No 144. Pipe up to and including DN350 shall be seamless. Pipe
DN400 and larger shall be seamless or welded with all longitudinal weld seams being
Property of Technip Oceania Pty Ltd. Copyright TECHNIP OCEANIA PTY. LTD.
All rights reserved
AP003164-G-SP-1300-0001r0 - W1440-P1-S-2100.doc
Doc. No : AP003164-G-SP-1300-0001
MUTINEER / EXETER FPSO Rev : 0
Piping Specification Page : 10 of 19
100% radiographed per EEMUA publication No 144, section 2. The nominal EEMUA
rating for wall thickness sizing shall be “20 bar” as a minimum.
Duplex is the term used in this specification for ferritic/austenitic SS of the generic type
UNS S31803. Supply of duplex SS shall be in accordance with the manufacturer’s
standard product route and using quality control, mechanical and corrosion testing
methods as per the product information sheets issued by the manufacturer and the
following requirements:
• Heat treatment - pipe shall be pickled, passivated and full solution annealed after
manufacture
• Corrosion test – intergranular ASTM A262 Practice E
• Chemical composition – nitrogen content, 0.15% (wt.) minimum
• Pipe shall be supplied with a minimum Pitting Resistance Equivalent (PRE) of 35 in
accordance with the following formula:
PRE = wt% Cr + (3.3 x wt% Mo) + (16 x wt% N)
• Ferrite count – 40% to 60% ASTM E562
• Hardness test – ASTM E18 (14 to 28 HRC)
• Welded pipes – 100% X-ray is required
Relevant control documents showing mechanical and corrosion testing requirements for
the product shall be issued to the Client Representative for review prior to contract award.
Pipe shall be supplied in accordance with ASTM A790 and meet the nominal size and
schedule requirements of ASME B36.19.
Pipe up to and including DN100 shall be seamless. DN150 and larger may be either
seamless or welded with all longitudinal weld seams being 100% radiographed and a
minimum joint quality factor (E) of 1.00 as defined by ASME B31.3. Welded pipe in the as-
welded condition shall have the same corrosion resistance as the parent material.
A heat analysis in accordance with ASTM A790 S1 shall be reported on the material
certificate.
Acceptable polymers include epoxy resins, polyester resins and vinyl ester resins. In
general, the Glass Transition Temperature of the resin used should be at least 20°C higher
than the specified maximum rated temperature. The inclusion of filler material in the resin
shall not be allowed (unless designed to enhance pipe properties such as fire retardance
or conductivity). The inside diameter of the GRE pipes shall have a resin rich layer.
Fibre reinforcement should be E-glass but other fibres may be used to enhance product
performance. The fibre shall be furnished with a suitable finish (coupling agent), which is
compatible with the resin system to be used. It is acceptable that conductive piping be
constructed by winding metal filaments within the main reinforcing layer provided that less
than 5% by weight of the total fibre content is metal filament.
Pipe support spacing and design shall in accordance with the requirements of the GRE
supplier.
Property of Technip Oceania Pty Ltd. Copyright TECHNIP OCEANIA PTY. LTD.
All rights reserved
AP003164-G-SP-1300-0001r0 - W1440-P1-S-2100.doc
Doc. No : AP003164-G-SP-1300-0001
MUTINEER / EXETER FPSO Rev : 0
Piping Specification Page : 11 of 19
Pipe fittings, other than non-metallic, copper and CuNi, shall be supplied with wall
thickness and nominal sizes that meet ASME B36.10 and B36.19.
CS forgings shall be supplied in the normalized condition. Fittings manufactured from pipe
shall comply with section 4.2.1 above.
Where austenitic or duplex SS fittings are specified, they shall conform with ASTM A182,
A403 or A815 and the same material requirements specified in Section 4.2.2 and 4.2.4
above.
Dimensions of metallic buttweld fittings shall be in accordance with ASME B16.9 and
threaded fittings to ASME B16.11. All 90° buttweld elbows shall be long radius (1.5D).
Fittings larger than DN40 and swage nipples shall not be manufactured from bar stock.
Swage nipples shall be manufactured from pipe per the applicable material class.
Repair by welding of wrought fittings is not permitted.
“O’let” type fittings shall be dimensioned to meet the branch reinforcement requirements of
ASME B31.3.
All CuNi elbows, tees, saddles and insert self-reinforcing branch connectors shall be
provided with proof burst test certificates and radiography certificates (where applicable) to
demonstrate compliance with the specification. Proof testing shall meet ASME B16.9
section 9 requirements.
For all instrument branch connections either integral equal or reducing flangeolets up to
50NB branch size shall be used instead of weldolets.
All flanges in buttweld piping shall be weld-neck (WN) unless specific requirements dictate
otherwise.
Austenitic or duplex SS flanges shall conform with ASTM A182 and shall comply with the
appropriate material requirements specified in section 4.2.2 and 4.2.4 above.
Flat face GRE flanges and fittings supplied with GRE piping are intended to interface the
GRE system with valves or other steel fittings. The flanges are to be supplied to ASME
B16.5 bolting dimensions for the specified flange rating and shall be of laminate
construction. Moulded flanges are not permitted. For cyclic pressure service, flanges shall
be rated on the static pressure rating of the system. The manufacturer’s installation bolt
torques for the flange shall be detailed in the installation specification.
Spades, spacers and blinds shall be in accordance with ASME B16.48 and shall have
gasket contact surface finishes as for flanges. Blind flanges outside the scope of ASME
B16.48 (e.g where corrosion allowance requirements are greater) shall have the thickness
calculated to suit line conditions.
Spades, spacers and blinds over 30kg shall be fitted with lifting lugs.
Flange facings shall be in accordance with ASME B16.5 for Raised Face, Flat Face and
Ring Type Joints. The facings of Class 150, 300 and 600 flanges shall be Raised Face
except where specified otherwise on the Piping Classes or P&IDs, eg for GRE piping. The
facings of classes 900 and 1500 flanges shall be Ring Type Joint.
Property of Technip Oceania Pty Ltd. Copyright TECHNIP OCEANIA PTY. LTD.
All rights reserved
AP003164-G-SP-1300-0001r0 - W1440-P1-S-2100.doc
Doc. No : AP003164-G-SP-1300-0001
MUTINEER / EXETER FPSO Rev : 0
Piping Specification Page : 12 of 19
Flange gasket surface finishes shall be in accordance with ASME B16.5 and the following:
Class 150 serrated spiral finish, roughness between Ra 6.3 and 12.5µm
Class 300 & above smooth finish, roughness between Ra 3.2 and 6.3µm
RTJ roughness of gasket groove side wall less than Ra 1.6µm
Orifice flanges, except for GRE piping systems, shall generally be Class 300 RF as a
minimum and meet the requirements of ASME B16.36.
Instrument connections shall generally be via single or double block and bleed
“Monoflange” or “Keyblok” (one piece) assemblies per the relevant Piping Class (refer also
Sections 4.5.7 and 4.5.8 below).
Flange bolting and gaskets shall be in accordance with the relevant Piping Class.
Studs of 1” diameter and smaller shall be UNC with those 11/8” diameter and larger being
UN8 series. Studs 1¼” diameter and larger are to be increased in length by a minimum of
one nut thickness to allow the use of hydraulic bolt tensioning equipment.
The need to use insulating gaskets for CS/SS dissimilar joints shall be determined on a
case by case basis.
4.6 Valves
4.6.1 General
Additional requirements for valves designated with individual instrument tag numbers shall
be as per the specific data sheet. Valve selection shall be in accordance with the relevant
Piping Class and associated valve data sheet.
All flanged valves shall be integral. Welded-on flanges are not permitted without approval
from the Purchaser.
Valves shall be bi-directional unless valve construction specifically renders this impractical
(e.g. globe, butterfly, check and needle valves). For uni-directional valves, an indicator
showing flow direction shall be cast/forged into the valve body.
Valve position indicators shall be designed so as to prevent incorrect orientation on the
valve assembly.
Valve actuators shall be in accordance with the valve data sheet. Manual actuators shall
be selected to allow operation at the valve’s rated pressure differential with a force no
greater than 350N.
Quarter turn valve handles shall be of the “leverlock” type and permanently fixed to the
valve stem by a bolt or nut.
Gearboxes shall be fitted with position indicators, have self-locking mechanisms and fully
sealed and protected to suit a corrosive marine environment.
The design of all valves shall be such that self-closing of the valve due to vibrations, etc
shall not occur.
Valves, except for non-metallic and gunmetal, shall be designed to meet the
pressure/temperature ratings as defined by ASME B16.34/B16.24 as a minimum.
Where Duplex SS valves are specified, they shall conform to the same material
requirements as specified in Section 4.2.4 above.
Property of Technip Oceania Pty Ltd. Copyright TECHNIP OCEANIA PTY. LTD.
All rights reserved
AP003164-G-SP-1300-0001r0 - W1440-P1-S-2100.doc
Doc. No : AP003164-G-SP-1300-0001
MUTINEER / EXETER FPSO Rev : 0
Piping Specification Page : 13 of 19
The Supplier may offer a superior alternative to those specified on the Valve Data Sheets
having regard for service conditions and the required operating characteristics. Materials
shall be selected such that galling does not occur and galvanic corrosion between
dissimilar metals is avoided.
Hard overlays, coatings or electroless nickel plating shall be used to provide wear/erosion
resistance and to prevent galling of parts in sliding contact where deemed necessary and
in addition to the requirements of the valve data sheets. Differential hardness between
valve seats and ball/disk/gate shall be maintained to prevent galling.
Where the valve data sheets specify “Manufacturer’s Standard” for materials, the Supplier
shall state the materials offered/supplied.
Stainless steel grade 304 material shall not be used for any components. This is
particularly relevant to the bolting of pressure retaining equipment such as valves.
Where fire safe requirements are specified, the valves shall be certified as fire safe and
performance tested in accordance with API 6FA.
Ball valves shall be fitted with double trunnions, unless otherwise specified for Class 150
valves DN200 and larger, Class 300 valves DN150 and larger and DN100 and larger
valves for Class 600 and higher. All other sizes shall be “floating ball” type unless
specified otherwise on the relevant Piping Class. A floating ball design may be used for
turret valves when ‘manifold valves’ are specified.
Ball valves shall be reduced bore unless stated otherwise. All ball valve designs shall
include anti-static devices and meet the design, dimensional and test requirements of API
6D or BS 5351 as applicable. All valves shall meet the pressure/temperature ratings of
ASME B16.34 as a minimum (note that API 6D ratings do not meet ASME B16.5 for all
materials).
Ball valves shall be fitted with blow-out proof stems and have the body split outside the
plane of the stem protrusion. Trunnion mounted balls shall have automatic body cavity
relief via seat design. Stem seal covers shall be bolted. Valve stems shall be designed so
that the stem “weak point” is outside of the valve body.
Valves other than gunmetal shall be designed to meet the requirements of ASME B16.34.
Valves shall be OS&Y, BB and rising stem. The disc shall be a ball type and hard faced.
Seats shall also be hard faced with the seats on valves DN50 and larger being renewable.
Gunmetal valves shall comply with API 6D.
Valve dimensions shall meet the requirements of ASME B16.10. Valve ends shall be in
accordance with the valve data sheet. Pressure/temperature ratings and valve design
shall meet the requirements of ASME B16.34.
Check valves, other than plastic and gunmetal, shall comply with the requirements of API
602 for sizes up to DN40 and API 594/API 6D for sizes DN50 and larger. For valve sizes
DN40 and smaller, spring return ball lift types shall be used and only mounted in the
horizontal position. For DN50 and larger, dual plate, spring return wafer pattern valves
shall be used. Class 600 and lower wafer valves shall be unlugged unless specified
Property of Technip Oceania Pty Ltd. Copyright TECHNIP OCEANIA PTY. LTD.
All rights reserved
AP003164-G-SP-1300-0001r0 - W1440-P1-S-2100.doc
Doc. No : AP003164-G-SP-1300-0001
MUTINEER / EXETER FPSO Rev : 0
Piping Specification Page : 14 of 19
otherwise. Class 900 and higher wafer valves shall be drilled-through lugged type.
Gunmetal valves shall comply with API 6D.
Gate valves, other than gunmetal, up to DN40 shall be of forged body construction and
meet the requirements of API 602. Valves shall be OS&Y, BB, rising stem, backseated
and of solid wedge construction. Both wedge and seats shall be hard faced.
Gate valves, other than gunmetal, DN50 and larger shall be in accordance with ASME 6D /
ASME B16.34. Valve construction shall be OS&Y, BB, rising stem, back seated and have
a solid wedge with renewable seat rings.
Gunmetal valves shall comply with API 6D.
Triple offset butterfly valves shall have metal seats and be of lugged design unless
specifically stated otherwise. Valve design shall meet the requirements of ASME B16.34
or API 609.
Valves shall allow the use of lever, gearbox or pneumatic actuators without the need for
valve modification. The actuator will be nominated on the valve data sheet, but it should
be possible to have commonality/interchangeability of valve bodies regardless of actuator
type.
Valve bodies/actuators shall be fitted with stops to prevent disc over-travel in either the
open or closed position.
The valve body lugs shall have the threads drilled out to prevent the studbolts corroding
within the lugs and to aid installation of the valves.
Monoflange assemblies are defined as one-piece double block and bleed valve
assemblies.
Minimum design requirements shall be in accordance with EEMUA Publication 182 and as
follows:
Assemblies shall incorporate a side and a top ½” NPTF instrument connection with one
port fitted with a 3000# NPT plug;
The double block and bleed valves within the assembly shall be of needle valve design
and shall meet the requirements of ASME B16.34 in terms of design materials, wall
thickness, rating and the following;
• Flange connection shall be ASME RF smooth finish or RTJ as applicable. Flange
thickness shall be increased to allow for internal drilling. Flange boltholes shall match
ASME B16.5 drilling. Slotted boltholes to allow multiple flange rating are not permitted.
• Needle valves shall be rising stem, have a back seat design and have bonnets
positively locked to the assemblies’ flange. Bonnet shall have adjustable stem
packing.
• The valve shall be of a fire-rated design and shall comply with API 6FA.
• Where stainless steel is used it shall be type 316 SS or Duplex SS as appropriate.
• The whole assembly shall be pressure tested to API 6D.
Property of Technip Oceania Pty Ltd. Copyright TECHNIP OCEANIA PTY. LTD.
All rights reserved
AP003164-G-SP-1300-0001r0 - W1440-P1-S-2100.doc
Doc. No : AP003164-G-SP-1300-0001
MUTINEER / EXETER FPSO Rev : 0
Piping Specification Page : 15 of 19
“Keybloks or Monoblocks” are defined as double block and bleed integral manifolds where
the isolation valves are ball valves.
Minimum design requirements shall be in accordance with EEMUA Publication 182 and as
follows:
• Assemblies for instrument use shall incorporate a side and a top ½” NPTF instrument
connection with one port fitted with a 3000# NPT plug.
• Valves shall be full bore type to allow rodding and elimination of internal pockets.
• The primary isolation valve shall be of a piping valve quality/design and shall meet the
requirements of ASME B16.34 in terms of design materials, wall thickness and rating.
• Flange connection shall be ASME RF smooth finish. Flange thickness shall be
increased to allow for internal drilling. Flange boltholes shall match ASME B16.5
drilling. Slotted boltholes to allow multiple flange rating are not permitted.
• Vent valve shall be a needle valve and shall be rising stem, have a back seat design
and have bonnets positively locked to the assembly. Bonnet shall have adjustable
stem packing.
• The valve shall be of a fire-rated design and shall comply with API 6FA.
• Where stainless steel is used it shall be type 316 SS or Duplex SS as appropriate.
• The whole assembly shall be pressure tested to API 6D.
• Materials shall be as per the valve data sheet.
Each valve shall be pressure tested in accordance with the requirements of the valve data
sheet. The maximum chloride content of the water for hydrotesting of SS valves shall be
30ppm.
All valves shall be subject to hydrostatic seat leakage testing. Allowable seat leakage rates
shall be as per Table 3.1 unless stated otherwise on the valve data sheets.
TABLE 3.1 VALVE TESTING
Valve Type Valve Seat Type Leakage Rate
Ball Soft Seated No visible leakage
Hard Metal Seated API 598
Butterfly Hard Metal Seated API 598
Check Soft Seated No visible leakage
Hard Metal Seated API 598
Gate Soft Seated No visible leakage
Hard Metal Seated API 598
Globe Metal Seated No visible leakage
Needle Soft/Metal Seated No visible leakage
Property of Technip Oceania Pty Ltd. Copyright TECHNIP OCEANIA PTY. LTD.
All rights reserved
AP003164-G-SP-1300-0001r0 - W1440-P1-S-2100.doc
Doc. No : AP003164-G-SP-1300-0001
MUTINEER / EXETER FPSO Rev : 0
Piping Specification Page : 16 of 19
Valve bodies and bonnets shall be subjected to all NDE requirements shown on the valve
data sheets and as described in the following sections. NDE of pipe and fittings shall be in
accordance with the nominated specification and any supplementary requirements
specified.
Radiography
Where specified on the valve data sheets, the radiographic technique employed shall be in
accordance with the recommendation of ASME V Article 2 for forgings and ASME V Article
3 for castings. Acceptance criteria shall be as specified in ASME B16.34 Annex B with the
additional requirements that no cracks or crack like defects are acceptable.
Magnetic Particle Inspection
Where specified on the valve data sheets, magnetic particle inspections shall be applied
using the detailed requirements, methods, procedures and qualifications specified in
ASME V Article 7. The wet particle technique using background paint shall be adopted
and the magnetising technique shall be appropriate to the component being inspected.
Acceptance criteria shall be as described in ASME VIII, Division 1, Appendix 7, Clause 7-
3(4) for liquid penetrant examination. In addition, linear defects shall be limited to a
maximum of 3mm.
Liquid Penetrant Examination
Where specified on the valve data sheets, liquid penetrant examination shall be applied
using the detailed requirements, methods, procedures and qualifications specified in
ASME V Article 6. Acceptance criteria shall be as specified for magnetic particle
inspection.
Ultrasonic Examination
Where specified on the valve data sheets, ultrasonic examination shall be applied using
the detailed requirements, methods, procedures and qualifications specified in ASME V
Article 5. Acceptance criteria shall be as specified in ASME B16.34 Annex E.
Defective cast valve bodies and bonnets may be repaired by welding in accordance with
the provisions of their respective standards subject to Purchaser approval of the Vendor’s
repair procedure. All weld repairs shall be mapped. Cast bodies and bonnets that leak
during hydrotesting will be rejected and shall not be repaired. Weld repair of forgings is
not permitted.
Welding and welder procedures and qualifications shall meet the requirements of ASME
IX. All weld repairs shall be carried out using filler materials, which in the as-welded and
final heat treated conditions have mechanical and corrosion resistance properties equal to
or better than the parent metal. The Supplier shall carry out heat treatment appropriate to
the material being repaired and NDE in accordance with section 4.5.9.2 following
completion of all repairs. All weld repairs shall be completed prior to any proposed final
heat treatment.
Property of Technip Oceania Pty Ltd. Copyright TECHNIP OCEANIA PTY. LTD.
All rights reserved
AP003164-G-SP-1300-0001r0 - W1440-P1-S-2100.doc
Doc. No : AP003164-G-SP-1300-0001
MUTINEER / EXETER FPSO Rev : 0
Piping Specification Page : 17 of 19
5.0 CERTIFICATION
5.1 General
Piping, Fittings and Flanges All non-metallic, copper & CuNi fittings DN40 and below
Gaskets All gaskets and ring type joints
Piping, Fittings and Flanges All non-metallic, copper & CuNi piping and associated
fittings other than as defined for Type A Certificates
All steel (carbon and stainless) piping and associated
fittings
Fasteners All flange bolts and nuts for flanges
The extent and type of non-destructive testing of welded joints in fabricated pipework shall
be in accordance with Table 6.1 below.
Where it is impractical to use radiography or ultrasonic testing, use magnetic particle
inspection (MPI) for carbon steel and dye penetrant inspection (DPI) for alloy steels.
TABLE 6.1 PIPING CLASS INSPECTION LEVELS
Property of Technip Oceania Pty Ltd. Copyright TECHNIP OCEANIA PTY. LTD.
All rights reserved
AP003164-G-SP-1300-0001r0 - W1440-P1-S-2100.doc
Doc. No : AP003164-G-SP-1300-0001
MUTINEER / EXETER FPSO Rev : 0
Piping Specification Page : 18 of 19
Piping classes shall be identified with the following 3 to 5 digit alphanumeric nominator:
rd th
3 /4 identifier Base Material Identification
A Carbon Steel
D Duplex Stainless Steel
PX GRE
CN 90/10 Copper Nickel
S Austenitic Stainless Steel
Property of Technip Oceania Pty Ltd. Copyright TECHNIP OCEANIA PTY. LTD.
All rights reserved
AP003164-G-SP-1300-0001r0 - W1440-P1-S-2100.doc
Doc. No : AP003164-G-SP-1300-0001
MUTINEER / EXETER FPSO Rev : 0
Piping Specification Page : 19 of 19
5th identifier A sequential single digit number identifying variations to the base
material
T Globe
B Ball
C Check
D Double block and bleed
G Gate
TO Triple offset butterfly
N Needle
F Butterfly
5th and 6th identifier a 2 digit sequential number identifying variations to the valve
type for the base material
R Reduced bore
F Full bore
CI Chemical Injection
G Gear operated
No letter Lever operated
For example, VBA12-F indicates a full bore ball valve in carbon steel, lever operated.
Property of Technip Oceania Pty Ltd. Copyright TECHNIP OCEANIA PTY. LTD.
All rights reserved
AP003164-G-SP-1300-0001r0 - W1440-P1-S-2100.doc
Doc. No : AP003164-G-SP-1300-0001
MUTINEER / EXETER FPSO Rev : 0
Piping Specification Page : A1 of A39
APPENDIX A
Piping Classes
TABLE A-2 WATER INJECTION SYSTEM PIPING CLASS AND SERVICE SUMMARY
Property of Technip Oceania Pty Ltd. Copyright TECHNIP OCEANIA PTY. LTD.
All rights reserved
AP003164-G-SP-1300-0001r0 - W1440-P1-S-2100.doc
Doc. No : AP003164-G-SP-1300-0001
MUTINEER / EXETER FPSO Rev : 0
Piping Specification Page : A2 of A39
BRANCH SIZE
15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
600 TW TW TW TW TW TW TW TW TW TR TR TR TR TR TR T
500 TW TW TW TW TW TW TW TW TR TR TR TR TR TR T
450 TW TW TW TW TW TW TW TW TR TR TR TR TR T
400 TW TW TW TW TW TW TW TR TR TR TR TR T
350 TW TW TW TW TW TW TW TR TR TR TR T
300 TW TW TW TW TW TW TW TR TR TR T
250 TW TW TW TW TW TW TR TR TR T
HEADER SIZE
200 TW TW TW TW TW TW TR TR T
150 TW TW TW TW TW TR TR T
100 TW TW TW TR TR TR T
80 TW TW TW TR TR T
50 TW TR TR TR T
40 TR TR TR T
25 TR TR T
20 TR T
15 T
Symbol Definition
TW Flangeolet / Weldolet
TR Reducing Tee
T Equal Tee
Notes.
1. If reducing tees are not available, weldolets may be used with the approval of the Piping Dept.
2. Where reinforcing is used, the pad shall be of the same material and thickness as the header and shall
have an outside diameter two times the branch outside diameter. A two piece sleeve is to be used if the
pad extends > 180 degrees around the header. Alternate pad design shall be in accordance with ASME
B31.3 and supported by appropriate calculations.
3. All branch connections 25NB and smaller shall be a reducing flangeolet (minimum base size 50NB) or an
equal flangeolet braced in two planes back to the main pipe.
Property of Technip Oceania Pty Ltd. Copyright TECHNIP OCEANIA PTY. LTD.
All rights reserved
AP003164-G-SP-1300-0001r0 - W1440-P1-S-2100.doc
Doc. No : AP003164-G-SP-1300-0001
MUTINEER / EXETER FPSO Rev : 0
Piping Specification Page : A3 of A39
BRANCH SIZE
40 50 80 100 150 200 250 300 350 400 450
450 FRS FRS FRS FRS FRS QTR QTR QTR QTR QTR QTE
400 FRS FRS FRS FRS QTR QTR QTR QTR QTR QTE
350 FRS FRS FRS FRS QTR QTR QTR QTR QTE
300 FRS FRS FRS QTR QTR QTR QTR QTE
HEADER SIZE
Symbol Definition
Notes.
Property of Technip Oceania Pty Ltd. Copyright TECHNIP OCEANIA PTY. LTD.
All rights reserved
AP003164-G-SP-1300-0001r0 - W1440-P1-S-2100.doc
Project Unit Material code Serial No. Rev.
AP003164 G SP - 1300 0001 0
MUTINEER-EXETER DEVELOPMENT
GAT 15 350 150 RF GATE VALVE. B16.34/API6D. A105. TRIM 13%Cr. VGA12 04
SOLID WEDGE. BB. OS&Y,R.STEM. HANDWHEEL
400 600 150 RF GATE VALVE.B16.34. A105. TRIM 13%Cr. SOLID VGA12-G 04
WEDGE. BB. OS&Y.R.STEM. FIRE SAFE. GEAR OP
CHE 15 40 150 RF LIFT CHECK VALVE. API 602. A105.TRIM 13% CR. VCA12
HORIZONTAL INSTALLATION.
CHE1 50 600 150 RF DUAL PLATE WAFER CHECK. API 594. A 216 WCB VCA184
BODY. TRIM 316
TOB1 150 600 150 RF TRIPLE OFFSET BUTTERFLY VALVE. API 609. WAFER VTOA12-G
LUG TYPE. A216 WCB BODY & DISC. SS316 TRIM &
SEATS. FIRE SAFE. GEAR OP
***** PIPES *****
PIP 15 40 BE 160 PIPE. A106 Gr B. ASME B36.10
50 80 BE 80 PIPE. A106 Gr B. ASME B36.10
100 250 BE 40 PIPE. A106 Gr B. ASME B36.10
300 400 BE STD PIPE. A106 Gr B. ASME B36.10
450 600 BE STD PIPE. A106 Gr B. ASME B36.10
***** FITTING *****
90E 15 400 BW AS PIPE 90 DEG. LR ELBOW. A234 GR.WPB SEAMLESS. ASME
B16.9
450 600 BW AS PIPE 90 DEG. LR ELBOW. A234 GR.WPB/WPBW. ASME
B16.9
MUTINEER-EXETER DEVELOPMENT
TEE 15 400 BW AS PIPE EQUAL TEE. A234 GR.WPB SEAMLESS. ASME B16.9
FLG1 15 600 300 RF AS PIPE WELDING NECK FLANGE. A105. ASME B16.5
FLG2 50 600 300 RF AS PIPE PAIR OF WELDING NECK ORIFICE FLANGES. A105.
ASME B16.36
MUTINEER-EXETER DEVELOPMENT
BLS 200 600 150 RF PADDLE BLANK. A516 GR.70 NORMALIZED. ASME
B16.48
SPA 200 600 150 RF PADDLE SPACER AND BLANK. A516 GR.70
NORMALIZED. ASME B16.48
NOTES
01 THREADED COMPONENTS ARE NOT PERMITTED IN HYDROCARBON SERVICE EXCEPT AS TEMPORARY HYDROTEST VENTS/DRAINS.
02 FOR ALL INSTRUMENT BRANCH CONNECTIONS EITHER INTEGRAL EQUAL OR REDUCING FLANGEOLETS UP TO 50NB BRANCH SIZE
SHALL BE USED INSTEAD OF WELDOLETS.
03 THE 1451 KPAG DESIGN PRESSURE AT 185 DEG C DESIGN TEMPERATURE IS FOR STEAM SERVICE.
04 GATE VALVES TO BE USED FOR STEAM SERVICE ONLY.
Project Unit Material code Serial No. Rev.
AP003164 G SP - 1300 0001 0
MUTINEER-EXETER DEVELOPMENT
CHE 15 40 150 RF LIFT CHECK VALVE. API 602. A105.TRIM 13% CR. VCY12
HORIZONTAL INSTALLATION.
CHE1 50 600 150 RF DUAL PLATE WAFER CHECK. API 594. A 216 WCB VCY184
BODY. TRIM 316
TOB1 150 600 150 RF TRIPLE OFFSET BUTTERFLY VALVE. API 609. VTOY12-G
WAFER LUG TYPE. A216 WCB BODY & DISC. SS316
TRIM & SEATS. FIRE SAFE. GEAR OP
***** PIPES *****
PIP 15 40 BE XXS PIPE. A106 Gr B. ASME B36.10
50 50 BE 160 PIPE. A106 Gr B. ASME B36.10
80 200 BE 80 PIPE. A106 Gr B. ASME B36.10
250 400 BE 40 PIPE. A106 Gr B. ASME B36.10
450 800 BE 30 PIPE. A106 Gr B. ASME B36.10
***** FITTINGS *****
90E 15 400 BW AS PIPE 90 DEG. LR ELBOW. A234 GR.WPB SEAMLESS.
ASME B16.9
450 600 BW AS PIPE 90 DEG. LR ELBOW. A234 GR.WPB/WPBW. ASME
B16.9
TEE 15 400 BW AS PIPE EQUAL TEE. A234 GR.WPB SEAMLESS. ASME B16.9
Project Unit Material code Serial No. Rev.
AP003164 G SP - 1300 0001 0
MUTINEER-EXETER DEVELOPMENT
NOL 15 600 300 PLAIN AS PIPE NIPOLET, A105, PLAIN TO MSS SP-97
FLG1 15 600 300 RF AS PIPE WELDING NECK FLANGE. A105. ASME B16.5
FLG2 50 600 300 RF AS PIPE PAIR OF WELDING NECK ORIFICE FLANGES. A105.
ASME B16.36
MUTINEER-EXETER DEVELOPMENT
BLS 200 600 150 RF PADDLE BLANK. A516 GR.70 NORMALIZED. ASME
B16.48
SPA 200 600 150 RF PADDLE SPACER & BLANK A516 GR.70
NORMALIZED. ASME B16.48
NOTES
01 THREADED COMPONENTS ARE NOT PERMITTED IN HYDROCARBON SERVICE EXCEPT AS TEMPORARY HYDROTEST VENTS/DRAINS
02 FOR ALL INSTRUMENT BRANCH CONNECTIONS EITHER INTEGRAL EQUAL OR REDUCING FLANGEOLETS UP TO 50NB BRANCH SIZE
SHALL BE USED INSTEAD OF WELDOLETS.
Project Unit Material code Serial No. Rev.
AP003164 G SP - 1300 0001 0
MUTINEER-EXETER DEVELOPMENT
CHE 15 40 300 RF LIFT CHECK VALVE. API 602. A105.TRIM 13% CR. VCA32
HORIZONTAL INSTALLATION.
CHE1 50 600 300 RF DUAL PLATE WAFER CHECK. API 594. A 216 WCB VCA384
BODY. TRIM 316
TOB1 150 600 300 RF TRIPLE OFFSET BUTTERFLY VALVE. API 609.
WAFER LUG TYPE. A216 WCB BODY & DISC. SS316
TRIM & SEATS. FIRE SAFE. GEAR OP VTOA32-G
***** PIPES *****
PIP 15 40 BE 160 PIPE. A106 Gr B. ASME B36.10
50 150 BE 80 PIPE. A106 Gr B. ASME B36.10
200 400 BE 40 PIPE. A106 Gr B. ASME B36.10
450 600 BE 40 PIPE. A106 Gr B. ASME B36.10
***** FITTINGS *****
90E 15 400 BW AS PIPE 90 DEG. LR ELBOW. A234 GR.WPB SEAMLESS.
ASME B16.9
450 600 BW AS PIPE 90 DEG. LR ELBOW. A234 GR.WPB/WPBW. ASME
B16.9
TEE 15 400 BW AS PIPE EQUAL TEE. A234 GR.WPB SEAMLESS. ASME B16.9
MUTINEER-EXETER DEVELOPMENT
NOL 15 600 300 PLAIN AS PIPE NIPOLET, A105, PLAIN TO MSS SP-97
FLG2 50 600 300 RF AS PIPE PAIR OF WELDING NECK ORIFICE FLANGES. A105.
ASME B16.36
BLS 200 600 300 RF PADDLE BLANK. A516 GR.70 NORMALIZED. ASME
B16.48
Project Unit Material code Serial No. Rev.
AP003164 G SP - 1300 0001 0
MUTINEER-EXETER DEVELOPMENT
SPA 200 600 300 RF PADDLE SPACER AND BLANK. A516 GR.70
NORMALIZED. ASME B16.48
NOTES
01 THREADED COMPONENTS ARE NOT PERMITTED IN HYDROCARBON SERVICE EXCEPT AS TEMPORARY HYDROTEST VENTS/DRAINS.
02 FOR ALL INSTRUMENT BRANCH CONNECTIONS EITHER INTEGRAL EQUAL OR REDUCING FLANGEOLETS UP TO 50NB BRANCH SIZE
SHALL BE USED INSTEAD OF WELDOLETS.
Project Unit Material code Serial No. Rev.
AP003164 G SP - 1300 0001 0
MUTINEER-EXETER DEVELOPMENT
CHE 15 40 300 RF LIFT CHECK VALVE. API 602. A105.TRIM 13% CR. VCY32
HORIZONTAL INSTALLATION.
CHE1 50 600 300 RF DUAL PLATE WAFER CHECK. API 594. A 216 WCB VCY384
BODY. TRIM 316
TOB1 150 600 300 RF TRIPLE OFFSET BUTTERFLY VALVE. API 609. VTOY32-G
WAFER LUG TYPE. A216 WCB BODY & DISC. SS316
TRIM & SEATS. FIRE SAFE. GEAR OP
***** PIPES *****
PIP 15 40 BE XXS PIPE. A106 Gr B. ASME B36.10
50 80 BE 160 PIPE. A106 Gr B. ASME B36.10
100 100 BE 120 PIPE. A106 Gr B. ASME B36.10
150 400 BE 80 PIPE. A106 Gr B. ASME B36.10
450 600 BE 80 PIPE. A106 Gr B. ASME B36.10
***** FITTINGS *****
90E 15 400 BW AS PIPE 90 DEG. LR ELBOW. A234 GR.WPB SEAMLESS.
ASME B16.9
450 600 BW AS PIPE 90 DEG. LR ELBOW. A234 GR.WPB/WPBW. ASME
B16.9
TEE 15 400 BW AS PIPE EQUAL TEE. A234 GR.WPB SEAMLESS. ASME B16.9
MUTINEER-EXETER DEVELOPMENT
FLG2 50 600 300 RF AS PIPE PAIR OF WELDING NECK ORIFICE FLANGES. A105.
ASME B16.36
BLS 200 600 300 RF PADDLE BLANK. A516 GR.70 NORMALIZED. ASME
B16.48
Project Unit Material code Serial No. Rev.
AP003164 G SP - 1300 0001 0
MUTINEER-EXETER DEVELOPMENT
SPA 200 600 300 RF PADDLE SPACER AND BLANK. A516 GR.70
NORMALIZED. ASME B16.48
NOTES
01 THREADED COMPONENTS ARE NOT PERMITTED IN HYDROCARBON SERVICE EXCEPT AS TEMPORARY HYDROTEST VENTS/DRAINS.
02 FOR ALL INSTRUMENT BRANCH CONNECTIONS EITHER INTEGRAL EQUAL OR REDUCING FLANGEOLETS UP TO 50NB BRANCH SIZE
SHALL BE USED INSTEAD OF WELDOLETS.
Project Unit Material code Serial No. Rev.
AP003164 G SP - 1300 0001 0
MUTINEER-EXETER DEVELOPMENT
CHE 25 40 1500 RTJ LIFT CHECK VALVE. API 602. A105.TRIM 13% CR. VCA153
HORIZONTAL INSTALLATION.
CHE1 50 600 1500 RTJ DUAL PLATE WAFER CHECK. LUG TYPE. API 594. VCA1584
A 216 WCB BODY. TRIM 316
TEE 25 400 BW AS PIPE EQUAL TEE. A234 GR.WPB SEAMLESS. ASME B16.9
MUTINEER-EXETER DEVELOPMENT
FLG2 50 600 1500 RTJ AS PIPE PAIR OF WELDING NECK ORIFICE FLANGES. A105.
ASME B16.36
BLF 25 600 1500 RTJ BLIND FLANGE. ASTM A105. ASME B16.5
***** GASKETS *****
GAS 25 600 1500 RTJ OCTAGONAL RING JOINT TYPE 'R'.SOFT
IRON.MAX.90 BHN B16.20(B16.5).CADM.PLATED
***** BOLTING *****
BOL 25 600 1500 RTJ STUB BOLT. A193 GR.B7. WITH 2 HEAVY
HEX.NUTSA194 GR.2H. FLUOROCARBON COATED
BLS 100 600 1500 RTJ PADDLE BLANK. A516 GR.70 NORMALIZED. ASME
B16.48
SPA 100 600 1500 RTJ PADDLE SPACER A516 GR.70 NORMALIZED. ASME
B16.48
NOTES
01 THREADED COMPONENTS ARE NOT PERMITTED IN HYDROCARBON SERVICE EXCEPT AS TEMPORARY HYDROTEST VENTS/DRAINS.
02 FOR ALL INSTRUMENT BRANCH CONNECTIONS EITHER INTEGRAL EQUAL OR REDUCING FLANGEOLETS UP TO 50NB BRANCH SIZE
SHALL BE USED INSTEAD OF WELDOLETS.
03 BALL MAY BE SUPPLIED IN CS WITH 5 MIL ENP.
Project Unit Material code Serial No. Rev.
AP003164 G SP - 1300 0001 0
MUTINEER-EXETER DEVELOPMENT
GAT 25 200 150 FF GATE VALVE ASME B16.34/API6D BS1400 AB2 VGH11
BODY AND MONEL K400 TRIM. SOLID WEDGE. OS
&Y
BUT 50 150 150 FF BUTTERFLY VALVE. API 609. BS1400 AB2 BODY & VFH183
DISC. MONEL K400 TRIM.
200 450 150 FF BUTTERFLY VALVE. API 609. BS1400 AB2 BODY & VFH183-G
DISC. MONEL K400 TRIM. G.O
CHE 15 40 150 FF LIFT CHECK VALVE. API 602. BS1400 AB2 VCH12
BODY.TRIM MONEL K400. HORIZONTAL
INSTALLATION.
CHE1 50 450 150 FF DUAL PLATE WAFER CHECK. API 594. BS1400 AB2 VCH184
BODY AND MONEL K400 TRIM. NBR SEAT
TOB1 150 450 150 FF TRIPLE OFFSET BUTTERFLY VALVE, API 609, VTODT01-G
WAFER TYPE, NiAlBr, BS1400 AB2,TRIM MONEL
K400, GEAR OP
***** PIPES ***** (Note 1)
PIP 25 25 B&S BY PIPE. RTRP EPOXY. BELL & SPIGOT. MANUF.STD.
VENDOR (GLASS FIB.REINF.EPOXY).ASTM 2996
40 40 B&S BY PIPE. RTRP EPOXY. BELL & SPIGOT. MANUF.STD.
VENDOR (GLASS FIB.REINF.EPOXY).ASTM 2996
50 80 B&S BY PIPE. RTRP EPOXY. BELL & SPIGOT. MANUF.STD.
VENDOR (GLASS FIB.REINF.EPOXY).ASTM 2996
100 100 B&S BY PIPE. RTRP EPOXY. BELL & SPIGOT. MANUF.STD.
VENDOR (GLASS FIB.REINF.EPOXY).ASTM 2996
150 150 B&S BY PIPE. RTRP EPOXY. BELL & SPIGOT. MANUF.STD.
VENDOR (GLASS FIB.REINF.EPOXY).ASTM 2996
200 200 B&S BY PIPE. RTRP EPOXY. BELL & SPIGOT. MANUF.STD.
VENDOR (GLASS FIB.REINF.EPOXY).ASTM 2996
250 250 B&S BY PIPE. RTRP EPOXY. BELL & SPIGOT. MANUF.STD.
VENDOR (GLASS FIB.REINF.EPOXY).ASTM 2996
300 300 B&S BY PIPE. RTRP EPOXY. BELL & SPIGOT. MANUF.STD.
VENDOR (GLASS FIB.REINF.EPOXY).ASTM 2996
350 350 B&S BY PIPE. RTRP EPOXY. BELL & SPIGOT. MANUF.STD.
VENDOR (GLASS FIB.REINF.EPOXY).ASTM 2996
400 400 B&S BY PIPE. RTRP EPOXY. BELL & SPIGOT. MANUF.STD.
VENDOR (GLASS FIB.REINF.EPOXY).ASTM 2996
450 450 B&S BY PIPE. RTRP EPOXY. BELL & SPIGOT. MANUF.STD.
VENDOR (GLASS FIB.REINF.EPOXY).ASTM 2996
Project Unit Material code Serial No. Rev.
AP003164 G SP - 1300 0001 0
MUTINEER-EXETER DEVELOPMENT
TEEF 25 450 150 QLF AS PIPE EQUAL TEE WITH FLANGE.RTRF EPOXY.
MANUFACTURER'S STD. (GRE-EPOXY)
TE1F 50 450 150 QLF AS PIPE REDUCING TEE WITH FLANGE. RTRF EPOXY.
MANUFACTURER'S STD.(GRE-EPOXY)
DCL 50 200 SBE AS PIPE DELUGE COUPLING RTRP EPOXY.WITH FRP &
STAINLSTEEL BUSHED OUTLET (FEMALE NPT)
***** FLANGES *****
FLG 25 450 150 FF AS PIPE FLANGE (HEAVY DUTY).RTRP EPOXY.DRILLED PER
B16.5.MAN.STD.D4024.SOCKET(GRE)
MUTINEER-EXETER DEVELOPMENT
NOTES
MUTINEER-EXETER DEVELOPMENT
GAT 15 200 150 FF GATE VALVE ASME B16.34/API6D BS1400 AB2 BODY VGH11
AND MONEL K400 TRIM. SOLID WEDGE. OS & Y
CHE 15 40 150 FF LIFT CHECK VALVE. API 602. BS1400 AB2 VCH12
CHE1 50 600 150 FF DUAL PLATE WAFER CHECK. API 594. BS1400 AB2 VCH184
BODY AND MONEL K400 TRIM. NBR SEAT
TOB1 150 600 150 FF TRIPLE OFFSET BUTTERFLY VALVE, API 609, VTODT01-G
WAFER TYPE, NiAlBr, BS1400 AB2,TRIM MONEL
K400, GEAR OP
MUTINEER-EXETER DEVELOPMENT
ERE 15 200 BW AS PIPE ECC. REDUCER, SMLS, 90/10 CU-NI, BS 2872 CN102,
EEMUA 146 SEC.1.
250 600 BW AS PIPE ECC. REDUCER, WELDED, 90/10 CU-NI, BS 2872
CN102, EEMUA 146 SEC.1.
STE2 15 600 300 RF AS PIPE LAP-JOINT STUB END, 90/10 CU-NI,BS2872 CN102 ,
B16.9,TYPE 'A'.
MUTINEER-EXETER DEVELOPMENT
NOL 15 600 3000 THR NIPOLET, 90/10 CU-NI, BS 2872 CN102, MNF. STD &
B1.20.1(NPT).
NOL1 15 600 3000 PE NIPOLET, 90/10 CU-NI, BS 2872 CN102, MNF. STD.
MUTINEER-EXETER DEVELOPMENT
BLS 200 600 150 FF PADDLE BLANK. 90/10 CU-NI BS 2870 CN102 LINED
A516 GR.70 NORMALIZED. API 590
SPA 200 600 150 FF PADDLE SPACER AND BLANK.90/10 CU-NI BS 2870
CN102 LINED A516 GR.70 NORMALIZED. ASME
B16.48
01 USE FULL FACE NEOPRENE GASKETS WITH MIN. SHORE 'A' HARDNESS OF 75 FOR BOLTING FLAT FACE SLIP-ON 90/10 CU-NI FLANGES
02 TO BE USED FOR ALUMINIUM BRONZE GATE VALVES, Y-TYPE STRAINERS, HOSEREELS, FLANGED EQUIPMENT ETC.
Project Unit Material code Serial No. Rev.
AP003164 G SP - 1300 0001 0
MUTINEER-EXETER DEVELOPMENT
CHE 15 40 150 RF LIFT CHECK VALVE. API 602. A182 F316 BODY & VCD12
TRIM. HORIZONTAL INSTALLATION.
CHE1 50 600 150 RF DUAL PLATE WAFER CHECK. API 594. A351 CF8M VCD184
BODY & TRIM
MUTINEER-EXETER DEVELOPMENT
BLF 15 600 150 RF BLIND FLANGE. ASTM A182 F316L. ASME B16.5
***** GASKETS *****
GAS 15 600 150 RF FLAT GASKET.TANGED GRAPHITE/AISI 316
INSERT.ASME B16.21(B16.5).2 MM THICK
MUTINEER-EXETER DEVELOPMENT
BLS 200 600 150 RF PADDLE BLANK. A240 GR.TP316. ASME B16.48
SPA 200 600 150 RF PADDLE SPACER A240 GR.TP316. ASME B16.48
NOTES
01 THREADED COMPONENTS ARE NOT PERMITTED IN HYDROCARBON SERVICE EXCEPT AS TEMPORARY HYDROTEST VENTS/DRAINS.
02 FOR ALL INSTRUMENT BRANCH CONNECTIONS EITHER INTEGRAL EQUAL OR REDUCING FLANGEOLETS UP TO 50NB BRANCH SIZE
SHALL BE USED INSTEAD OF WELDOLETS.
Project Unit Material code Serial No. Rev.
AP003164 G SP - 1300 0001 0
MUTINEER-EXETER DEVELOPMENT
PIPING CLASSES Page
CHE 15 40 300 RF LIFT CHECK VALVE. API 602. A182 F316 BODY & VCD32
TRIM. HORIZONTAL INSTALLATION.
CHE1 50 400 300 RF DUAL PLATE WAFER CHECK. API 594. A351 CF8M VCD384
BODY & TRIM
MUTINEER-EXETER DEVELOPMENT
PIPING CLASSES Page
BLF 15 400 300 RF BLIND FLANGE. ASTM A182 F316L. ASME B16.5
***** GASKETS *****
GAS 15 400 300 RF FLAT GASKET.TANGED GRAPHITE/AISI 316
INSERT.ASME B16.21(B16.5).2 MM THICK
MUTINEER-EXETER DEVELOPMENT
PIPING CLASSES Page
BLS 200 400 300 RF PADDLE BLANK. A240 GR.TP316. ASME B16.48
SPA 200 400 300 RF PADDLE SPACER A240 GR.TP316. ASME B16.48
NOTES
01 THREADED COMPONENTS ARE NOT PERMITTED IN HYDROCARBON SERVICE EXCEPT AS TEMPORARY HYDROTEST VENTS/DRAINS.
02 FOR ALL INSTRUMENT BRANCH CONNECTIONS EITHER INTEGRAL EQUAL OR REDUCING FLANGEOLETS UP TO 50NB BRANCH SIZE
SHALL BE USED INSTEAD OF WELDOLETS.
Project Unit Material code Serial No. Rev.
AP003164 G SP - 1300 0001 0
MUTINEER-EXETER DEVELOPMENT
PIPING CLASSES Page
BAL 20 50 1500 RTJ BALL VALVE.RED. BORE.B16.34.A 182 F316 BODY & VBD153-R
TRIM. PEEK SEAT.FIRE SAFE.LEVER
CHE 15 40 1500 RTJ LIFT CHECK VALVE. API 602. A182 F316 BODY & VCD154
TRIM. HORIZONTAL INSTALLATION.
50 50 1500 RTJ DUAL PLATE WAFER CHECK. LUG TYPE. API 594. VCD1584
A351 CF8M BODY & TRIM
DBB 15 50 1500 RTJ MONOFLANGE DOUBLE BLOCK (OS&Y NEEDLE) & VDD153
BLEED (NEEDLE). A182 F316. TRIM 316. FLG X
NPT(F). MFR STD.
DBB1 15 50 1500 RTJ INTEGRAL DOUBLE BLOCK(BALL) & BLEED VDD153-F
(NEEDLE). A182 F316. TRIM 316. DOUBLE FLG. MFR
STD.
***** PIPES *****
PIP 15 25 BE 80S PIPE. STAINLESS STEEL. A312 TP316L. SEAMLESS
MUTINEER-EXETER DEVELOPMENT
PIPING CLASSES Page
BLF 15 50 1500 RTJ BLIND FLANGE. ASTM A182 F316L. ASME B16.5
***** GASKETS *****
GAS 15 50 1500 RTJ OCTAGONAL RING JOINT TYPE 'R'. SS 316. MAX.
160HB B16.20 (B16.5)
***** BOLTING *****
BOL 15 50 1500 RTJ STUB BOLT. A193 GR.B7. WITH 2 HEAVY HEX
NUTS. A194 GR.2H. FLUOROCARBON COATED
***** MISCELLANEOUS *****
F8S 15 50 1500 RTJ SPECTACLE BLIND. A240 GR.TP316. FIG.8
BLANK.ASME B16.48
NOTES
01 THREADED COMPONENTS ARE NOT PERMITTED IN HYDROCARBON SERVICE EXCEPT AS TEMPORARY HYDROTEST VENTS/DRAINS.
02 FOR ALL INSTRUMENT BRANCH CONNECTIONS EITHER INTEGRAL EQUAL OR REDUCING FLANGEOLETS UP TO 50NB BRANCH SIZE
SHALL BE USED INSTEAD OF WELDOLETS.
Project Unit Material code Serial No. Rev.
AP003164 G SP - 1300 0001 0
MUTINEER-EXETER DEVELOPMENT
PIPING CLASSES Page
BAL 20 50 2500 RTJ BALL VALVE.RED. BORE.B16.34.A 182 F316 BODY & VBD253-R
TRIM. PEEK SEAT.FIRE SAFE.LEVER
CHE 15 40 2500 RTJ LIFT CHECK VALVE. API 602. A182 F316 BODY & VCD254
TRIM. HORIZONTAL INSTALLATION.
50 50 2500 RTJ DUAL PLATE WAFER CHECK. LUG TYPE. API 594. VCD2584
A351 CF8M BODY & TRIM
DBB 15 50 2500 RTJ MONOFLANGE DOUBLE BLOCK (OS&Y NEEDLE) & VDD253
BLEED (NEEDLE). A182 F316. TRIM 316. FLG X
NPT(F). MFR STD.
DBB1 15 50 2500 RTJ INTEGRAL DOUBLE BLOCK(BALL)&BLEED VDD253-F
(NEEDLE).A182 F316.TRIM 316.DOUBLE FLG.MFR
STD.
MUTINEER-EXETER DEVELOPMENT
PIPING CLASSES Page
BLF 15 50 2500 RTJ BLIND FLANGE. ASTM A182 F316L. ASME B16.5
***** GASKETS *****
GAS 15 50 2500 RTJ OCTAGONAL RING JOINT TYPE 'R'.SS 316.
MAX.160HB B16.20 (B16.5)
***** BOLTING *****
BOL 15 80 2500 RTJ STUD BOLT. A193 GR.B7. WITH 2 HEAVY HEX
.NUTS A194 GR.2H. FLUOROCARBON COATED
***** MISCELLANEOUS *****
F8S 15 50 2500 RTJ SPECTACLE BLIND. A240 GR.TP316. FIG.8
BLANK.API 590
NOTES
01 THREADED COMPONENTS ARE NOT PERMITTED IN HYDROCARBON SERVICE EXCEPT AS TEMPORARY HYDROTEST VENTS/DRAINS.
02 FOR ALL INSTRUMENT BRANCH CONNECTIONS EITHER INTEGRAL EQUAL OR REDUCING FLANGEOLETS UP TO 50NB BRANCH SIZE
SHALL BE USED INSTEAD OF WELDOLETS.
Project Unit Material code Serial No. Rev.
AP003164 G SP - 1300 0001 0
MUTINEER-EXETER DEVELOPMENT
CHE 15 40 150 RF LIFT CHECK VALVE. API 602. A182 F51 BODY & VCE12
TRIM. HORIZONTAL INSTALLATION.
CHE1 50 600 150 RF DUAL PLATE WAFER CHECK. API 594. A182 F51 VCE184
BODY & TRIM
TOB1 150 600 150 RF TRIPLE OFFSET BUTTERFLY VALVE. API 609. VTOE12-G
WAFER LUG TYPE. A890 Gr 4A BODY, UNS32760
TRIM & SEATS. FIRE SAFE. GEAR OP
***** PIPES *****
PIP 15 25 BE 160 PIPE. DUPLEX STAINLESS STEEL. SEAMLESS.
A790-UNS S31803. B36.19
40 50 BE 40S PIPE. DUPLEX STAINLESS STEEL. SEAMLESS.
A790-UNS S31803. B36.19
80 150 BE 10S PIPE. DUPLEX STAINLESS STEEL. SEAMLESS.
A790-UNS S31803. B36.19
200 600 BE 10S PIPE. DUPLEX STAINLESS STEEL. WELDED
A928-CL1 UNS S31803. B36.19
***** FITTINGS *****
90E 15 200 BW AS PIPE 90 DEGREE LR ELBOW.A815-CL. WP-S UNS
S31803.SEAMLESS. ASME B16.9
Project Unit Material code Serial No. Rev.
AP003164 G SP - 1300 0001 0
MUTINEER-EXETER DEVELOPMENT
HPL 15 40 3000 NPT HEXAGONAL HEAD PLUG. A182 F51. ASME B16.11 01
MUTINEER-EXETER DEVELOPMENT
FLG1 15 600 300 RF AS PIPE WELDING NECK FLANGE. A182 F51. ASME B16.5
BLS 200 600 150 RF PADDLE BLANK. A240 UNS S31803. ASME B16.48
SPA 200 600 150 RF PADDLE SPACER & BLANK. A240-UNS S31803.
ASME B16.48
NOTES
01 THREADED COMPONENTS ARE NOT PERMITTED IN HYDROCARBON SERVICE EXCEPT AS TEMPORARY HYDROTEST VENTS/DRAINS.
02 FOR ALL INSTRUMENT BRANCH CONNECTIONS EITHER INTEGRAL EQUAL OR REDUCING FLANGEOLETS UP TO 50NB BRANCH SIZE
SHALL BE USED INSTEAD OF WELDOLETS.
Project Unit Material code Serial No. Rev.
AP003164 G SP - 1300 0001 0
MUTINEER-EXETER DEVELOPMENT
CHE 15 40 300 RF LIFT CHECK VALVE. API 602. A182 F51 BODY & VCE32
TRIM. HORIZONTAL INSTALLATION.
CHE1 50 600 300 RF DUAL PLATE WAFER CHECK. API 594. A182 F51 VCE384
BODY & TRIM
TOB1 150 600 300 RF TRIPLE OFFSET BUTTERFLY VALVE. API 609. VTOE32-G
WAFER LUG TYPE. A890 Gr 4A BODY, UNS32760
TRIM & SEATS. FIRE SAFE. GEAR OP
MUTINEER-EXETER DEVELOPMENT
NOL 15 600 300 PLAIN AS PIPE NIPOLET, A182 F51, PLAIN TO MSS SP-97
HPL 15 40 3000 NPT HEXAGONAL HEAD PLUG. A182 F51. ASME B16.11 01
MUTINEER-EXETER DEVELOPMENT
BLS 200 600 300 RF PADDLE BLANK. A240 UNS S31803. ASME B16.48
SPA 200 600 300 RF PADDLE SPACER & BLANK. A240-UNS S31803.
ASME B16.48
NOTES
01 THREADED COMPONENTS ARE NOT PERMITTED IN HYDROCARBON SERVICE EXCEPT AS TEMPORARY HYDROTEST VENTS/DRAINS.
02 FOR ALL INSTRUMENT BRANCH CONNECTIONS EITHER INTEGRAL EQUAL OR REDUCING FLANGEOLETS UP TO 50NB BRANCH SIZE
SHALL BE USED INSTEAD OF WELDOLETS.
Project Unit Material code Serial No. Rev.
AP003164 G SP - 1300 0001 0
MUTINEER-EXETER DEVELOPMENT
BAL1 15 80 1500 RTJ FULL BORE BALL VALVE.B16.34/API6D. A 182 F51 VBE153-F
BODY AND TRIM.PEEK SEAT.FIRE SAFE.LEVER
100 400 1500 RTJ FULL BORE BALL VALVE.B16.34/API6D. A 182 F51 VBE153-FG
BODY AND TRIM. PEEK SEAT. FIRE SAFE.GEAR
CHE 15 40 1500 RTJ LIFT CHECK VALVE. API 602. A182 F51 BODY & VCE153
TRIM. HORIZONTAL INSTALLATION.
CHE1 50 400 1500 RTJ DUAL PLATE WAFER CHECK. LUG TYPE. A 182 F51 VCE1584
BODY AND TRIM. API 594
DBB 15 50 1500 RTJ MONOFLANGE DOUBLE BLOCK (OS&Y NEEDLE) & VDE153
BLEED (NEEDLE). A182 F51BODY & TRIM. FLG X
NPT(F). MFR STD.
DBB1 15 50 1500 RTJ INTEGRAL DOUBLE BLOCK(BALL)&BLEED VDE153-F
(NEEDLE).A182 F51BODY&TRIM.DOUBLE FLG.MFR
STD.
MUTINEER-EXETER DEVELOPMENT
HPL 15 40 6000 NPT HEXAGONAL HEAD PLUG. A182 F51. ASME B16.11 01
FLG2 50 400 1500 RTJ AS PIPE PAIR OF WELDING NECK ORIFICE FLANGES.
ASTMA182 F51. ASME B16.36
BLF 15 400 1500 RTJ BLIND FLANGE. A182 F51. ASME B16.5
***** GASKETS *****
GAS 15 400 1500 RTJ OVAL RING JOINT TYPE 'R'.DUPLEX SS UNS 31803.
MAX.160HB B16.20(B16.5)
***** BOLTING *****
BOL 15 400 1500 RTJ STUB BOLT. A193 GR.B7. WITH 2 HEAVY
HEX.NUTSA194 GR.2H. FLUOROCARBON COATED
MUTINEER-EXETER DEVELOPMENT
BLS 100 400 1500 RTJ PADDLE BLANK. A240 UNS S31803. ASME B16.48
SPA 100 400 900 RTJ PADDLE SPACER & BLANK. A240-UNS S31803.
ASME B16.48
NOTES
01 THREADED COMPONENTS ARE NOT PERMITTED IN HYDROCARBON SERVICE EXCEPT AS TEMPORARY HYDROTEST VENTS/DRAINS.
02 FOR ALL INSTRUMENT BRANCH CONNECTIONS EITHER INTEGRAL EQUAL OR REDUCING FLANGEOLETS UP TO 50NB BRANCH SIZE
SHALL BE USED INSTEAD OF WELDOLETS.
Doc. No : AP003164-G-SP-1300-0001
MUTINEER / EXETER FPSO Rev : 0
Piping Specification Page : B1 of B132
APPENDIX B
Property of Technip Oceania Pty Ltd. Copyright TECHNIP OCEANIA PTY. LTD.
All rights reserved
AP003164-G-SP-1300-0001r0 - W1440-P1-S-2100.doc
Doc. No : AP003164-G-SP-1300-0001
MUTINEER / EXETER FPSO Rev : 0
Piping Specification Page : B2 of B132
Property of Technip Oceania Pty Ltd. Copyright TECHNIP OCEANIA PTY. LTD.
All rights reserved
AP003164-G-SP-1300-0001r0 - W1440-P1-S-2100.doc
Doc. No : AP003164-G-SP-1300-0001
MUTINEER / EXETER FPSO Rev : 0
Piping Specification Page : B3 of B132
Property of Technip Oceania Pty Ltd. Copyright TECHNIP OCEANIA PTY. LTD.
All rights reserved
AP003164-G-SP-1300-0001r0 - W1440-P1-S-2100.doc
Doc. No : AP003164-G-SP-1300-0001
MUTINEER / EXETER FPSO Rev : 0
Piping Specification Page : B4 of B132
Property of Technip Oceania Pty Ltd. Copyright TECHNIP OCEANIA PTY. LTD.
All rights reserved
AP003164-G-SP-1300-0001r0 - W1440-P1-S-2100.doc
Doc. No : AP003164-G-SP-1300-0001
MUTINEER / EXETER FPSO Rev : 0
Piping Specification Page : B5 of B132
Property of Technip Oceania Pty Ltd. Copyright TECHNIP OCEANIA PTY. LTD.
All rights reserved
AP003164-G-SP-1300-0001r0 - W1440-P1-S-2100.doc
Data / requisition sheet for
VALVE DATA SHEET - VTA12
1 REQUIRED OFFERED
2 Size range DN 15 - 200
3 Specification ASME B16.34 / API 6D
4 Tag No. VTA12
5 Piping Class 1A3
6 Class 150
7
8 VALVE TYPE Globe Valve (Straight Pattern)
9
10
11 END CONNECTION AND RATING Flanged to ASME B16.5, raised face Class 150
12
13
14 MATERIAL
15 Gasket Manufacturer's Standard (Non Asbestos)
16 Body design Bolted Bonnet, Outside Screw and Yoke, Rising Stem
17 Body Material Forged or Cast Carbon Steel ASTM A105 or
18 ASTM A 216 GR WCB/WCC
19 Trim Design Plug Type Disc, Renewable Seat
20
21 Trim Material 13% Cr Steel Stem, Seat and Disc
22
23 Packing Material Manufacturer's Standard (Non Asbestos)
24
25 VALVE OPERATOR Handwheel
26
27 BOLTING
28 Bonnet & Gland
29 Studs ASTM A 193 GR B7 Fluorocarbon Coated
30 Nuts ASTM A194 GR 2H Fluorocarbon Coated
31
32
33
34
35 DESIGN CONDITIONS Pressure / Temperature ratings to ASME B16.34
36 Plus 0°C to Plus 150 °C
37
38 TESTS
39 Hydrostatic
40 Body Note 2
41 Seat Note 2
42
43 INSPECTION AND TESTING REQUIREMENT API 598
44
45 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
46
47 REMARKS
48
49 Notes:
50 1) Test duration shall be in accordance with API 6D.
51 2) Test pressure shall be in accordance with ASME B16.34.
52 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
53 4) No repair by welding is allowed for casting / forging.
54 5) The specification for valves having a design temperature above 150oC shall be submitted to the Purchaser for approval.
55
56
57
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 250 - 300
3 Specification ASME B16.34 / API 6D
4 Tag No. VTA12-G
5 Piping Class 1A3
6 Class 150
7
8 VALVE TYPE Globe Valve (Straight Pattern)
9
10
11 END CONNECTION AND RATING Flanged to ASME B16.5, raised face Class 150
12
13
14 MATERIAL
15 Gasket Manufacturer's Standard (Non Asbestos)
16 Body design Bolted Bonnet, Outside Screw and Yoke, Rising Stem
17 Body Material Forged or Cast Carbon Steel ASTM A105 or
18 ASTM A 216 GR WCB/WCC
19 Trim Design Plug Type Disc, Renewable Seat
20
21 Trim Material 13% Cr Steel Stem, Seat and Disc
22
23 Packing Material Manufacturer's Standard (Non Asbestos)
24
25 VALVE OPERATOR Gear Operator
26
27 BOLTING
28 Bonnet & Gland
29 Studs ASTM A 193 GR B7 Fluorocarbon Coated
30 Nuts ASTM A194 GR 2H Fluorocarbon Coated
31
32
33
34
35 DESIGN CONDITIONS Pressure / Temperature ratings to ASME B16.34
36 Plus 0°C to Plus 150 °C
37
38 TESTS
39 Hydrostatic
40 Body Note 2
41 Seat Note 2
42
43 INSPECTION AND TESTING REQUIREMENT API 598
44
45 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
46
47 REMARKS
48
49 Notes:
50 1) Test duration shall be in accordance with API 6D.
51 2) Test pressure shall be in accordance with ASME B16.34.
52 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
53 4) No repair by welding is allowed for casting / forging.
54 5) The specification for valves having a design temperature above 150oC shall be submitted to the Purchaser for approval.
55
56
57
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 350
3 Specification ASME B16.34 / API 6D
4 Tag No. VGA12
5 Piping Class 1A3
6 Class 150
7
8 VALVE TYPE Gate Valve
9
10
11 END CONNECTION AND RATING Flanged to ASME B16.5, raised face Class 150
12
13
14 MATERIAL
15 Gasket Sp. Wound SS 316 with graph. filler/Soft Iron corrugated
16 Body design Bolted Bonnet, Outside Screw and Yoke, Rising Stem
17 Body Material Forged or Cast Carbon Steel ASTM A105 or
18 ASTM A 216 GR WCB/WCC
19 Trim Design Solid Wedge, Renewable Seat
20
21 Trim Material 13% Cr Steel Stem, Seat and Disc
22
23 Packing Material Braided Non Asbestos Graphite Impregnated
24
25 VALVE OPERATOR Handwheel
26
27 BOLTING
28 Bonnet & Gland
29 Studs ASTM A 193 GR B7 FLUOROCARBON COATED
30 Nuts ASTM A194 GR 2H FLUOROCARBON COATED
31
32
33
34
35 DESIGN CONDITIONS Pressure / Temperature ratings to ASME B16.34
36 Plus 0°C to Plus 185 °C
37
38 TESTS
39 Hydrostatic
40 Body Note 2
41 Seat Note 2
42
43 INSPECTION AND TESTING REQUIREMENT API 598
44
45 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
46
47 REMARKS
48
49 Notes:
50 1) Test duration shall be in accordance with API 6D.
51 2) Test pressure shall be in accordance with ASME B16.34.
52 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
53 4) No repair by welding is allowed for casting / forging.
54 5) The specification for valves having a design temperature above 185oC shall be submitted to the Purchaser for approval.
55
56
57
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 400 - 600
3 Specification ASME B16.34 / API 6D
4 Tag No. VGA12-G
5 Piping Class 1A3
6 Class 150
7
8 VALVE TYPE Gate Valve
9
10
11 END CONNECTION AND RATING Flanged to ASME B16.5, raised face Class 150
12
13
14 MATERIAL
15 Gasket Sp. Wound SS 316 with graph. filler/Soft Iron corrugated
16 Body design Bolted Bonnet, Outside Screw and Yoke, Rising Stem
17 Body Material Forged or Cast Carbon Steel ASTM A105 or
18 ASTM A 216 GR WCB/WCC
19 Trim Design Solid Wedge, Renewable Seat
20
21 Trim Material 13% Cr Steel Stem, Seat and Disc
22
23 Packing Material Braided Non Asbestos Graphite Impregnated
24
25 VALVE OPERATOR Gear Operator
26
27 BOLTING
28 Bonnet & Gland
29 Studs ASTM A 193 GR B7 FLUOROCARBON COATED
30 Nuts ASTM A194 GR 2H FLUOROCARBON COATED
31
32
33
34
35 DESIGN CONDITIONS Pressure / Temperature ratings to ASME B16.34
36 Plus 0°C to Plus 185 °C
37
38 TESTS
39 Hydrostatic
40 Body Note 2
41 Seat Note 2
42
43 INSPECTION AND TESTING REQUIREMENT API 598
44
45 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
46
47 REMARKS
48
49 Notes:
50 1) Test duration shall be in accordance with API 6D.
51 2) Test pressure shall be in accordance with ASME B16.34.
52 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
53 4) No repair by welding is allowed for casting / forging.
54 5) The specification for valves having a design temperature above 185oC shall be submitted to the Purchaser for approval.
55
56
57
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 20 - 150
3 Specification ASME B16.34 / API 6D
4 Tag No. VBA12-R
5 Piping Class 1A3
6 Class 150
7
8 VALVE DESCRIPTION Ball Valve, Carbon Steel, CL 150, Flanged RF. Reduced Bore, Fire Safe,
9 Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti Blowout
10 Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension ASME B16.10 Table 1 Column 19
13 Bore Reduced
14 Bonnet / Adapter Fixing Bolted
15 Operation Lever Operated
16 Construction ball Seat supported
17 End Connections Class 150 Flanged Ends To ASME B16.5, Raised Face
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
21 Body/Bonnet/Adapter ASTM A 105 or A216 - WCB / WCC
22 Ball ASTM A 182 - F316 or A351 - CF8M
23 Trim/Stem ASTM A 182 - F316 or A 705 - 630
24 Seats and Seals PTFE Seat Inserts, PTFE Seals
25 O-Ring Elast-O-Lion Minus 40
26 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner & Outer
29 Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ASME B16.34
34 Temperature Plus 0°C to Plus 150 °C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 4
41 - Seat Note 4
42 - Air Seat Note 4
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46
47 REMARKS
48 Notes:
49 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
50 2) Valve to be firesafe to API 6FA / API 607.
51 3) Valve to have body cavity pressure release
52 4) Test pressure shall be in accordance with ASME B16.34.
53 5) Ball position indicator shall be provided
54 6) Stem sealant injection shall be provided for valves 6" and larger, all sealant injection points shall incorporate a non return valve.
55 7) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
56 8) No repair by welding is allowed on castings/forgings
57 9) The specification for valves having a design temperature above 150oC shall be submitted to the Purchaser for approval.
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 200 - 600
3 Specification ASME B16.34 / API 6D
4 Tag No. VBA12-RG
5 Piping Class 1A3
6 Class 150
7
8 VALVE DESCRIPTION Ball Valve, Carbon Steel, CL 150, Flanged RF. Reduced Bore, Fire Safe,
9 Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti Blowout
10 Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension API 6D
13 Bore Reduced
14 Bonnet / Adapter Fixing Bolted
15 Operation Gear operated
16 Construction ball Trunnion supported
17 End Connections Class 150 Flanged Ends To ASME B16.5, Raised Face
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
21 Body/Bonnet/Adapter ASTM A 105 or A216 - WCB / WCC
22 Ball ASTM A 182 - F316 or A351 - CF8M
23 Trim/Stem ASTM A 182 - F316 or A 705 - 630
24 Seats and Seals PTFE Seat Inserts, PTFE Seals
25 O-Ring Elast-O-Lion Minus 40
26 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner & Outer
29 Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ASME B16.34
34 Temperature Plus 0°C to Plus 150 °C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 4
41 - Seat Note 4
42 - Air Seat Note 4
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46
47 REMARKS
48 Notes:
49 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
50 2) Valve to be firesafe to API 6FA / API 607.
51 3) Valve to have body cavity pressure release
52 4) Test pressure shall be in accordance with ASME B16.34.
53 5) Ball position indicator shall be provided
54 6) Stem sealant injection shall be provided for valve size DN 150 and larger, all sealant injection points shall incorporate a non return valve.
55 7) Valves shall be supplied with water jet proof gear operator.
56 8) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
57 9) No repair by welding is allowed on castings/forgings.
58 10) The specification for valves having a design temperature above 150oC shall be submitted to the Purchaser for approval.
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 150
3 Specification ASME B16.34 / API 6D
4 Tag No. VBA12-F
5 Piping Class 1A3
6 Class 150
7
8 VALVE DESCRIPTION Ball Valve, Carbon Steel, CL 150, Flanged RF. Full Bore, Fire Safe, Fitted
9 with Graphite Fire Seals, Side Entry, Bolted Body Anti Blowout Stem,
10 Anti-Static Device.
11 GENERAL
12 Face to Face Dimension ASME B16.10, Table 1, Column 19
13 Bore Full
14 Bonnet / Adapter Fixing Bolted
15 Operation Lever Operated
16 Construction ball Seat supported
17 End Connections Class 150 Flanged Ends To ASME B16.5, Raised Face
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
21 Body/Bonnet/Adapter ASTM A 105 or A216 - WCB / WCC
22 Ball ASTM A 182 - F316 or A351 - CF8M
23 Trim/Stem ASTM A 182 - F316 or A 705 - 630
24 Seats and Seals PTFE Seat Inserts, PTFE Seals
25 O-Ring Elast-O-Lion Minus 40
26 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner & Outer
29 Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ASME B16.34
34 Temperature Plus 0°C to Plus 150 °C
35 - Operating
36 - Blowdown -
37 TESTS
38 Hydrostatic
39 - Body Note 4
40 - Seat Note 4
41 - Air Seat Note 4
42 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
43 INSPECTION In accordance with Purchase Order
44
45 REMARKS
46 Notes:
47 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
48 2) Valve to be firesafe to API 6FA / API 607.
49 3) Valve to have body cavity pressure release
50 4) Test pressure shall be in accordance with ASME B16.34.
51 5) Ball position indicator shall be provided
52 6) Stem sealant injection shall be provided for valves 6" and larger, all sealant injection points shall incorporate a non return valve.
53 7) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
54 8) No repair by welding is allowed on castings/forgings
55 9) The specification for valves having a design temperature above 150oC shall be submitted to the Purchaser for approval.
56
57
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 200 - 600
3 Specification ASME B16.34 / API 6D
4 Tag No. VBA12-FG
5 Piping Class 1A3
6 Class 150
7
8 VALVE DESCRIPTION Ball Valve, Carbon Steel, CL 150, Flanged RF. Full Bore, Fire Safe, Fitted
9 with Graphite Fire Seals, Side Entry, Bolted Body Anti Blowout Stem,
10 Anti-Static Device.
11 GENERAL
12 Face to Face Dimension API 6D
13 Bore Full
14 Bonnet / Adapter Fixing Bolted
15 Operation Gear operated
16 Construction ball Trunnion supported
17 End Connections Class 150 Flanged Ends To ASME B16.5, Raised Face
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
21 Body/Bonnet/Adapter ASTM A 105 or A216 - WCB / WCC
22 Ball ASTM A 182 - F316 or A351 - CF8M
23 Trim/Stem ASTM A 182 - F316 or A 705 - 630
24 Seats and Seals PTFE Seat Inserts, PTFE Seals
25 O-Ring Elast-O-Lion Minus 40
26 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner & Outer
29 Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ASME B16.34
34 Temperature Plus 0°C to Plus 150 °C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 4
41 - Seat Note 4
42 - Air Seat Note 4
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46
47 REMARKS
48 Notes:
49 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
50 2) Valve to be firesafe to API 6FA / API 607.
51 3) Valve to have body cavity pressure release
52 4) Test pressure shall be in accordance with ASME B16.34.
53 5) Ball position indicator shall be provided
54 6) Stem sealant injection shall be provided for valve size DN 150 and larger, all sealant injection points shall incorporate a non return valve.
55 7) Valves shall be supplied with water jet proof gear operator.
56 8) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
57 9) No repair by welding is allowed on castings/forgings.
58 10) The specification for valves having a design temperature above 150oC shall be submitted to the Purchaser for approval.
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 40
3 Specification API 602
4 Tag No. VCA12
5 Piping Class 1A3
6 Class 150
7
8 VALVE TYPE Check -Piston Type
9
10
11 END CONNECTION AND RATING Flanged to ASME B16.5, raised face Class 150
12
13
14 MATERIAL
15 Gasket Manufacturer's Standard (Non Asbestos)
16 Body design Horizontal Flow, spring assisted, bolted bonnet
17 Body Material ASTM A 105 or A216 - WCB / WCC
18 Trim Design Metal to Metal Seats (Renewable)
19 Trim Material 13% Cr Steel
20 Packing Material NA
21 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
22
23 Spring ASTM B637 UNS N07750
24
25
26 VALVE OPERATOR NA
27
28
29 DESIGN CONDITIONS
30 Pressure Rating Class 150
31 Temperature
32 - Operating PLUS 0°C to PLUS 150° C
33
34
35 TESTS
36 Body Note 2
37 Seat Note 2
38
39
40 INSPECTION AND TESTING REQUIREMENT API 598
41
42 CERTIFICATION DIN 50049 - 3.1B for Body and Bonnet T/Cover
43
44
45 REMARKS
46 Notes:
47 1) Test duration shall be in accordance with API 6D.
48 2) Test pressure shall be in accordance with ASME B16.34.
49 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
50 4) No repair by welding is allowed for casting / forging.
51 5) The specification for valves having a design temperature above 150oC shall be submitted to the Purchaser for approval.
52
53
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 600
3 Specification API 594
4 Tag No. VCA184
5 Piping Class 1A3
6 Class 150
7
8 VALVE TYPE Wafer Check, Dual Plate, (For use in the Horizontal or the
9 vertical with upward flow)
10
11 END CONNECTION AND RATING Suitable for mounting between ASME B16.5 raised
12 face class 150 lb flanges
13
14 MATERIAL
15 Gasket NA
16 Body design Wafer Type - Spring Loaded Dual Plate
17 Body Material
18 Forged A105
19 Cast A216 WCB/WCC
20
21 Trim Design Metal to Metal seats (Integral)
22
23 Trim Material Stainless steel 316 plates with stellite overlay on
24 body & plate seating areas. Stainless steel
25 hinge and stop pins, B637 UNS N07750 springs
26 Packing Material NA
27
28 VALVE OPERATOR NA
29
30 BOLTING
31 Bonnet & Gland NA
32 Stud NA
33 Nuts NA
34
35 DESIGN CONDITIONS
36 Pressure Pressure / Temperature ratings to ASME B16.34
37 Temperature Plus 0°C to Plus 150 °C
38 - Operating
39 TESTS
40 Hydrostatic
41 Body Note 2
42 Seat Note 2
43
44
45 INSPECTION AND TESTING REQUIREMENT API 598
46
47 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
48
49 REMARKS
50 Notes:
51 1) Test duration shall be in accordance with API 6D.
52 2) Test pressure shall be in accordance with ASME B16.34.
53 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
54 4) No repair by welding is allowed for casting / forging.
55 5) The specification for valves having a design temperature above 150oC shall be submitted to the Purchaser for approval.
56
57
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification ASME B16.34
4 Tag No. VDA12
5 Piping Class 1A3
6 Class 150
7
8 VALVE TYPE Integral Double Block (O.S&Y needle) & Bleed (needle), Fire
9 safe
10
11 END CONNECTION AND RATING Inlet with ASME B16.5 150# RF, 2 off 15mm NPTF outlet
12 connections, one located in the centre of the monoflange,
13 the other on the edge of the monoflange, edge connection
14 fitted with a 3000# plug
15
16 MATERIAL
17 Valves, Body and Trim A105 with SS316L trim
18 Gland Packing Peek seat / Grafoil seal
19 Flange A105
20 Packing Material NA
21 Bolting ASTM A 193 B7 / A194 2H
22
23
24
25
26 VALVE OPERATOR Handwheel
27
28
29
30
31 DESIGN CONDITIONS
32 Pressure Pressure / Temperature ratings to ASME B16.34
33 Temperature 0°C to PLUS 150° C
34 - Operating
35
36 TESTS
37 Hydrostatic
38 Body Note 3
39 Seat Note 3
40 Pneumatic Note 3
41
42 INSPECTION AND TESTING REQUIREMENT API 598
43
44 CERTIFICATION EN 10204 - 3.1B for all pressure containing parts
45
46 REMARKS
47 Notes:
48 1) Test duration shall be in accordance with API 6D.
49 2) Valve to be firesafe to API 6FA / API 607.
50 3) Test pressure shall be in accordance with ASME B16.34.
51 4) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
52 5) No repair by welding is allowed on castings/ forgings.
53 6) The specification for valves having a design temperature above 150oC shall be submitted to the Purchaser for approval.
54
55
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification ASME B16.34
4 Tag No. VDA12-F
5 Piping Class 1A3
6 Class 150
7
8 VALVE TYPE
Integral Double Block (ball) & Bleed (needle), Fire safe
9
10
11 END CONNECTION AND RATING Inlet and outlet with ASME B16.5 150# RF
12
13
14 MATERIAL
15 Valves, Body and Trim A105 with SS316L trim
16 Gland Packing Peek seat / Grafoil seal
17 Flange A105N
18 Packing Material NA
19 Bolting NA
20
21
22
23
24
25
26 VALVE OPERATOR Lever operated
27
28
29
30
31 DESIGN CONDITIONS
32 Pressure Pressure / Temperature ratings to ASME B16.34
33 Temperature Plus 0°C to Plus 150 °C
34 - Operating
35
36 TESTS
37 Hydrostatic
38 Body Note 3
39 Seat Note 3
40 Pneumatic Note 3
41
42 INSPECTION AND TESTING REQUIREMENT API 598
43
44 CERTIFICATION EN 10204 - 3.1B for all pressure containing parts
45
46 REMARKS
47 Notes:
48 1) Test duration shall be in accordance with API 6D.
49 2) Valve to be firesafe to API 6FA / API 607.
50 3) Test pressure shall be in accordance with ASME B16.34.
51 4) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
52 5) No repair by welding is allowed on castings/ forgings.
53 6) The specification for valves having a design temperature above 150oC shall be submitted to the Purchaser for approval.
54
55
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 150 - 600
3 Specification API 609
4 Tag No. VTOA12-G
5 Piping Class 1A3
6 Class 150
7
8 VALVE TYPE Triple Offset Butterfly Valve, Wafer Lug Type, Fire Safe, CS Note 6
9 Body, SS316 Trim, Anti-blowout Stem
10
11 END CONNECTION AND RATING Suitable for mounting between ASME B16.5 raised face CL
12 150lb flanges
13
14 MATERIAL
15 Body Material ASTM A216 WCB
16 Disk ASTM A216 WCB
17 Shaft / trunnion A276 Gr 316
18 Gland Plate AISI 316
19 Body Seat/Seal AISI 316
20 Disc Seat/Seal AISI 316
21 Mounting Plate Steel
21 Gaskets Graphite
22 Bearing AISI 316/hard chrome plated
23 Packing Graphite passivated
24 Bolting
Stainless Steel type 316
25
26
27 VALVE OPERATOR Gear Operated
28
29
30 DESIGN CONDITIONS
31 Pressure Pressure / Temperature ratings to ASME B16.34
32 Temperature Plus 0°C to Plus 150 °C
33 - Operating
34
35 TESTS
36 Hydrostatic
37 Body Note 2
38 Seat Note 2
39 Pneumatic
40
41 INSPECTION AND TESTING REQUIREMENT API 598
42 MARKING API 609 / MSS SP-25
43 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
44
45 REMARKS
46 Notes:
47 1) Test duration shall be in accordance with API 6D and zero leakage for metal seat as stated in API 598.
48 2) Test pressure shall be in accordance with ASME B16.34.
49 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
50 4) No repair by welding is allowed for casting / forging.
51 5) Valve to be firesafe to API 6FA / API 607.
52 6) The threads of the lugs shall be drilled out to allow the studbolts to slide through.
53 7) The specification for valves having a design temperature above 150oC shall be submitted to the Purchaser for approval.
54
55
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 200
3 Specification ASME B16.34 / API 6D
4 Tag No. VTY12
5 Piping Class 1A6
6 Class 150
7
8 VALVE TYPE Globe Valve (Straight Pattern)
9
10
11 END CONNECTION AND RATING Flanged to ASME B16.5, raised face Class 150
12
13
14 MATERIAL
15 Gasket Manufacturer's Standard (Non Asbestos)
16 Body design Bolted Bonnet, Outside Screw and Yoke, Rising Stem
17 Body Material Forged or Cast Carbon Steel ASTM A105 or
18 ASTM A 216 GR WCB/WCC
19 Trim Design Plug Type Disc, Renewable Seat
20
21 Trim Material 13% Cr Steel Stem, Seat and Disc
22
23 Packing Material Manufacturer's Standard (Non Asbestos)
24
25 VALVE OPERATOR Handwheel
26
27 BOLTING
28 Bonnet & Gland
29 Studs ASTM A 193 GR B7 Fluorocarbon Coated
30 Nuts ASTM A194 GR 2H Fluorocarbon Coated
31
32
33
34
35 DESIGN CONDITIONS Pressure / Temperature ratings to ASME B16.34
36 Plus 0°C to Plus 120 °C
37
38 TESTS
39 Hydrostatic
40 Body Note 2
41 Seat Note 2
42
43 INSPECTION AND TESTING REQUIREMENT API 598
44
45 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
46
47 REMARKS
48
49 Notes:
50 1) Test duration shall be in accordance with API 6D.
51 2) Test pressure shall be in accordance with ASME B16.34.
52 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34 plus a corrosion allowance of 6mm.
53 4) No repair by welding is allowed for casting / forging.
54
55
56
57
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 250 - 300
3 Specification ASME B16.34 / API 6D
4 Tag No. VTY12-G
5 Piping Class 1A6
6 Class 150
7
8 VALVE TYPE Globe Valve (Straight Pattern)
9
10
11 END CONNECTION AND RATING Flanged to ASME B16.5, raised face Class 150
12
13
14 MATERIAL
15 Gasket Manufacturer's Standard (Non Asbestos)
16 Body design Bolted Bonnet, Outside Screw and Yoke, Rising Stem
17 Body Material Forged or Cast Carbon Steel ASTM A105 or
18 ASTM A 216 GR WCB/WCC
19 Trim Design Plug Type Disc, Renewable Seat
20
21 Trim Material 13% Cr Steel Stem, Seat and Disc
22
23 Packing Material Manufacturer's Standard (Non Asbestos)
24
25 VALVE OPERATOR Gear Operator
26
27 BOLTING
28 Bonnet & Gland
29 Studs ASTM A 193 GR B7 Fluorocarbon Coated
30 Nuts ASTM A194 GR 2H Fluorocarbon Coated
31
32
33
34
35 DESIGN CONDITIONS Pressure / Temperature ratings to ASME B16.34
36 Plus 0°C to Plus 120 °C
37
38 TESTS
39 Hydrostatic
40 Body Note 2
41 Seat Note 2
42
43 INSPECTION AND TESTING REQUIREMENT API 598
44
45 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
46
47 REMARKS
48
49 Notes:
50 1) Test duration shall be in accordance with API 6D.
51 2) Test pressure shall be in accordance with ASME B16.34.
52 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34 plus a corrosion allowance of 6mm.
53 4) No repair by welding is allowed for casting / forging.
54
55
56
57
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 20 - 150
3 Specification ASME B16.34 / API 6D
4 Tag No. VBY12-R
5 Piping Class 1A6
6 Class 150
7
8 VALVE DESCRIPTION Ball Valve, Carbon Steel, CL 150, Flanged RF. Reduced Bore, Fire Safe,
9 Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti Blowout
10 Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension ASME B16.10 Table 1 Column 19
13 Bore Reduced
14 Bonnet / Adapter Fixing Bolted
15 Operation Lever Operated
16 Construction ball Seat supported
17 End Connections Class 150 Flanged Ends To ASME B16.5, Raised Face
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
21 Body/Bonnet/Adapter ASTM A 105 or A216 - WCB / WCC
22 Ball ASTM A 182 - F316 or A351 - CF8M
23 Trim/Stem ASTM A 182 - F316 or A 705 - 630
24 Seats and Seals PTFE Seat Inserts, PTFE Seals
25 O-Ring Elast-O-Lion Minus 40
26 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ASME B16.34
34 Temperature PLUS 0°C to PLUS 120° C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 4
41 - Seat Note 4
42 - Air Seat Note 4
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46
47 REMARKS
48 Notes:
49 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
50 2) Valve to be firesafe to API 6FA / API 607.
51 3) Valve to have body cavity pressure release
52 4) Test pressure shall be in accordance with ASME B16.34.
53 5) Ball position indicator shall be provided
54 6) Stem sealant injection shall be provided for valves 6" and larger, all sealant injection points shall incorporate a non return valve.
55 7) Minimum thickness of valve bodies shall be in accordance with ASME B16.34 plus a corrosion allowance of 6mm.
56 8) No repair by welding is allowed on castings/forgings
57
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 200 - 600
3 Specification ASME B16.34 / API 6D
4 Tag No. VBY12-RG
5 Piping Class 1A6
6 Class 150
7
8 VALVE DESCRIPTION Ball Valve, Carbon Steel, CL 150, Flanged RF. Reduced Bore, Fire Safe,
9 Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti Blowout
10 Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension API 6D
13 Bore Reduced
14 Bonnet / Adapter Fixing Bolted
15 Operation Gear operated
16 Construction ball Trunnion supported
17 End Connections Class 150 Flanged Ends To ASME B16.5, Raised Face
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
21 Body/Bonnet/Adapter ASTM A 105 or A216 - WCB / WCC
22 Ball ASTM A 182 - F316 or A351 - CF8M
23 Trim/Stem ASTM A 182 - F316 or A 705 - 630
24 Seats and Seals PTFE Seat Inserts, PTFE Seals
25 O-Ring Elast-O-Lion Minus 40
26 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ASME B16.34
34 Temperature PLUS 0°C to PLUS 120° C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 4
41 - Seat Note 4
42 - Air Seat Note 4
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46
47 REMARKS
48 Notes:
49 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
50 2) Valve to be firesafe to API 6FA / API 607.
51 3) Valve to have body cavity pressure release
52 4) Test pressure shall be in accordance with ASME B16.34.
53 5) Ball position indicator shall be provided
54 6) Stem sealant injection shall be provided for valve size DN 150 and larger, all sealant injection points shall incorporate a non return valve.
55 7) Valves shall be supplied with water jet proof gear operator.
8) Minimum thickness of valve bodies shall be in accordance with ASME B16.34 plus a corrosion allowance of 6mm.
56 9) No repair by welding is allowed on castings/forgings.
57
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 150
3 Specification ASME B16.34 / API 6D
4 Tag No. VBY12-F
5 Piping Class 1A6
6 Class 150
7
8 VALVE DESCRIPTION Ball Valve, Carbon Steel, CL 150, Flanged RF. Full Bore, Fire Safe,
9 Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti Blowout
10 Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension ASME B16.10, Table 1, Column 19
13 Bore Full
14 Bonnet / Adapter Fixing Bolted
15 Operation Lever Operated
16 Construction ball Seat supported
17 End Connections Class 150 Flanged Ends To ASME B16.5, Raised Face
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
21 Body/Bonnet/Adapter ASTM A 105 or A216 - WCB / WCC
22 Ball ASTM A 182 - F316 or A351 - CF8M
23 Trim/Stem ASTM A 182 - F316 or A 705 - 630
24 Seats and Seals PTFE Seat Inserts, PTFE Seals
25 O-Ring Elast-O-Lion Minus 40
26 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ASME B16.34
34 Temperature PLUS 0°C to PLUS 120° C
35 - Operating
36 - Blowdown -
37 TESTS
38 Hydrostatic
39 - Body Note 4
40 - Seat Note 4
41 - Air Seat Note 4
42 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
43 INSPECTION In accordance with Purchase Order
44
45 REMARKS
46 Notes:
47 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
48 2) Valve to be firesafe to API 6FA / API 607.
49 3) Valve to have body cavity pressure release
50 4) Test pressure shall be in accordance with ASME B16.34.
51 5) Ball position indicator shall be provided
52 6) Stem sealant injection shall be provided for valves 6" and larger, all sealant injection points shall incorporate a non return valve.
53 7) Minimum thickness of valve bodies shall be in accordance with ASME B16.34 plus a corrosion allowance of 6mm.
54 8) No repair by welding is allowed on castings/forgings
55
56
57
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 200 - 600
3 Specification ASME B16.34 / API 6D
4 Tag No. VBY12-FG
5 Piping Class 1A6
6 Class 150
7
8 VALVE DESCRIPTION Ball Valve, Carbon Steel, CL 150, Flanged RF. Full Bore, Fire Safe,
9 Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti Blowout
10 Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension API 6D
13 Bore Full
14 Bonnet / Adapter Fixing Bolted
15 Operation Gear operated
16 Construction ball Trunnion supported
17 End Connections Class 150 Flanged Ends To ASME B16.5, Raised Face
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
21 Body/Bonnet/Adapter ASTM A 105 or A216 - WCB / WCC
22 Ball ASTM A 182 - F316 or A351 - CF8M
23 Trim/Stem ASTM A 182 - F316 or A 705 - 630
24 Seats and Seals PTFE Seat Inserts, PTFE Seals
25 O-Ring Elast-O-Lion Minus 40
26 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ASME B16.34
34 Temperature PLUS 0°C to PLUS 120° C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 4
41 - Seat Note 4
42 - Air Seat Note 4
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46
47 REMARKS
48 Notes:
49 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
50 2) Valve to be firesafe to API 6FA / API 607.
51 3) Valve to have body cavity pressure release
52 4) Test pressure shall be in accordance with ASME B16.34.
53 5) Ball position indicator shall be provided
54 6) Stem sealant injection shall be provided for valve size DN 150 and larger, all sealant injection points shall incorporate a non return valve.
55 7) Valves shall be supplied with water jet proof gear operator.
8) Minimum thickness of valve bodies shall be in accordance with ASME B16.34 plus a corrosion allowance of 6mm.
56 9) No repair by welding is allowed on castings/forgings.
57
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 40
3 Specification API 602
4 Tag No. VCY12
5 Piping Class 1A6
6 Class 150
7
8 VALVE TYPE Check -Piston Type
9
10
11 END CONNECTION AND RATING Flanged to ASME B16.5, raised face Class 150
12
13
14 MATERIAL
15 Gasket Manufacturer's Standard (Non Asbestos)
16 Body design Horizontal Flow, spring assisted, bolted bonnet
17 Body Material ASTM A 105 or A216 - WCB / WCC
18 Trim Design Metal to Metal Seats (Renewable)
19 Trim Material 13% Cr Steel
20 Packing Material NA
21 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
22
23 Spring ASTM B637 UNS N07750
24
25
26 VALVE OPERATOR NA
27
28
29 DESIGN CONDITIONS
30 Pressure Rating Class 150
31 Temperature
32 - Operating PLUS 0°C to PLUS 150° C
33
34
35 TESTS
36 Body Note 2
37 Seat Note 2
38
39
40 INSPECTION AND TESTING REQUIREMENT API 598
41
42 CERTIFICATION DIN 50049 - 3.1B for Body and Bonnet T/Cover
43
44
45 REMARKS
46 Notes:
47 1) Test duration shall be in accordance with API 6D.
48 2) Test pressure shall be in accordance with ASME B16.34.
49 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34 plus a corrosion allowance of 6mm.
50 4) No repair by welding is allowed for casting / forging.
51
52
53
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 600
3 Specification API 594
4 Tag No. VCY184
5 Piping Class 1A6
6 Class 150
7
8 VALVE TYPE Wafer Check, Dual Plate, (For use in the Horizontal or the
9 vertical with upward flow)
10
11 END CONNECTION AND RATING Suitable for mounting between ASME B16.5 raised
12 face class 150 lb flanges
13
14 MATERIAL
15 Gasket NA
16 Body design Wafer Type - Spring Loaded Dual Plate
17 Body Material
18 Forged A105
19 Cast A216 WCB/WCC
20
21 Trim Design Metal to Metal seats (Integral)
22
23 Trim Material Stainless steel 316 plates with stellite overlay on
24 body & plate seating areas. Stainless steel
25 hinge and stop pins, B637 UNS N07750 springs
26 Packing Material NA
27
28 VALVE OPERATOR NA
29
30 BOLTING
31 Bonnet & Gland NA
32 Stud NA
33 Nuts NA
34
35 DESIGN CONDITIONS
36 Pressure Pressure / Temperature ratings to ASME B16.34
37 Temperature PLUS 0°C to PLUS 120° C
38 - Operating
39 TESTS
40 Hydrostatic
41 Body Note 2
42 Seat Note 2
43
44
45 INSPECTION AND TESTING REQUIREMENT API 598
46
47 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
48
49 REMARKS
50 Notes:
51 1) Test duration shall be in accordance with API 6D.
52 2) Test pressure shall be in accordance with ASME B16.34.
53 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34 plus a corrosion allowance of 6mm.
54 4) No repair by welding is allowed for casting / forging.
55
56
57
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification ASME B16.34
4 Tag No. VDY12
5 Piping Class 1A6
6 Class 150
7
8 VALVE TYPE Integral Double Block (O.S&Y needle) & Bleed (needle),
9 Fire safe
10
11 END CONNECTION AND RATING Inlet with ASME B16.5 150# RF, 2 off 15mm NPTF outlet
12 connections, one located in the centre of the monoflange,
13 the other on the edge of the monoflange, edge connection
14 fitted with a 3000# plug
15
16 MATERIAL
17 Valves, Body and Trim A105 with SS316L trim
18 Gland Packing Peek seat / Grafoil seal
19 Flange A105
20 Packing Material NA
21 Bolting ASTM A 193 B7 / A194 2H
22
23
24
25
26 VALVE OPERATOR Handwheel
27
28
29
30
31 DESIGN CONDITIONS
32 Pressure Pressure / Temperature ratings to ASME B16.34
33 Temperature 0°C to PLUS 120° C
34 - Operating
35
36 TESTS
37 Hydrostatic
38 Body Note 3
39 Seat Note 3
40 Pneumatic Note 3
41
42 INSPECTION AND TESTING REQUIREMENT API 598
43
44 CERTIFICATION EN 10204 - 3.1B for all pressure containing parts
45
46 REMARKS
47 Notes:
48 1) Test duration shall be in accordance with API 6D.
49 2) Valve to be firesafe to API 6FA / API 607.
50 3) Test pressure shall be in accordance with ASME B16.34.
51 4) Minimum thickness of valve bodies shall be in accordance with ASME B16.34 plus a corrosion allowance of 6mm.
52 5) No repair by welding is allowed on castings/ forgings.
53
54
55
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification ASME B16.34
4 Tag No. VDY12-F
5 Piping Class 1A6
6 Class 150
7
8 VALVE TYPE
Integral Double Block (ball) & Bleed (needle), Fire safe
9
10
11 END CONNECTION AND RATING Inlet and outlet with ASME B16.5 150# RF
12
13
14 MATERIAL
15 Valves, Body and Trim A105 with SS316L trim
16 Gland Packing Peek seat / Grafoil seal
17 Flange A105
18 Packing Material NA
19 Bolting NA
20
21
22
23
24
25
26 VALVE OPERATOR Lever operated
27
28
29
30
31 DESIGN CONDITIONS
32 Pressure Pressure / Temperature ratings to ASME B16.34
33 Temperature PLUS 0°C to PLUS 120° C
34 - Operating
35
36 TESTS
37 Hydrostatic
38 Body Note 3
39 Seat Note 3
40 Pneumatic Note 3
41
42 INSPECTION AND TESTING REQUIREMENT API 598
43
44 CERTIFICATION EN 10204 - 3.1B for all pressure containing parts
45
46 REMARKS
47 Notes:
48 1) Test duration shall be in accordance with API 6D.
49 2) Valve to be firesafe to API 6FA / API 607.
50 3) Test pressure shall be in accordance with ASME B16.34.
51 4) Minimum thickness of valve bodies shall be in accordance with ASME B16.34 plus a corrosion allowance of 6mm.
52 5) No repair by welding is allowed on castings/ forgings.
53
54
55
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 150 - 600
3 Specification API 609
4 Tag No. VTOY12-G
5 Piping Class 1A6
6 Class 150
7
8 VALVE TYPE Triple Offset Butterfly Valve, Wafer Lug Type, Fire Safe, Note 6
9 CS Body, SS316 Trim, Anti-blowout Stem
10
11 END CONNECTION AND RATING Suitable for mounting between ASME B16.5 raised face
12 CL 150lb flanges
13
14 MATERIAL
15 Body Material ASTM A216 WCB
16 Disk ASTM A216 WCB
17 Shaft / trunnion A276 Gr 316
18 Gland Plate AISI 316
19 Body Seat/Seal AISI 316
20 Disc Seat/Seal AISI 316
21 Mounting Plate Steel
21 Gaskets Graphite
22 Bearing AISI 316/hard chrome plated
23 Packing Graphite passivated
24 Bolting
Stainless Steel type 316
25
26
27 VALVE OPERATOR Gear Operated
28
29
30 DESIGN CONDITIONS
31 Pressure Pressure / Temperature ratings to ASME B16.34
32 Temperature PLUS 0°C to PLUS 120° C
33 - Operating
34
35 TESTS
36 Hydrostatic
37 Body Note 2
38 Seat Note 2
39 Pneumatic
40
41 INSPECTION AND TESTING REQUIREMENT API 598
42 MARKING API 609 / MSS SP-25
43 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
44
45 REMARKS
46 Notes:
47 1) Test duration shall be in accordance with API 6D and zero leakage for metal seat as stated in API 598.
48 2) Test pressure shall be in accordance with ASME B16.34.
49 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34 plus a corrosion allowance of 6mm.
50 4) No repair by welding is allowed for casting / forging.
51 5) Valve to be firesafe to API 6FA / API 607.
52 6) The threads of the lugs shall be drilled out to allow the studbolts to slide through.
53
54
55
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 200
3 Specification ASME B16.34 / API 6D
4 Tag No. VTA32
5 Piping Class 3A3
6 Class 300
7
8 VALVE TYPE Globe Valve (Straight Pattern)
9
10
11 END CONNECTION AND RATING 300#RF
12
13
14 MATERIAL
15 Gasket Manufacturer's Standard (Non Asbestos)
16 Body design Bolted Bonnet, Outside Srew and Yoke, Rising Stem
17 Body Material Forged or Cast Carbon Steel ASTM A105 or
18 ASTM A 216 GR WCB
19 Trim Design Plug Type Disc, Renewable Seat
20
21 Trim Material 13%Cr Steel Stem, Seat and Disc
22
23 Packing Material Manufacturer's Standard (Non Asbestos)
24
25 VALVE OPERATOR Handwheel
26
27 BOLTING
28 Bonnet & Gland
29 Studs ASTM A 193 GR B7 Fluorocarbon Coated
30 Nuts ASTM A194 GR 2H Fluorocarbon Coated
31
32
33
34
35 DESIGN CONDITIONS Pressure / Temperature ratings to ANSI B16.34
36 Plus 0°C to Plus 120 °C
37
38 TESTS
39 Hydrostatic
40 Body Note 2
41 Seat Note 2
42
43 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
44 INSPECTION AND TESTING REQUIREMENT API 598
45
46 REMARKS
47
48 Notes:
49 1) Test duration shall be in accordance with API 6D.
50 2) Test pressure shall be in accordance with ASME B16.34.
51 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
52 4) No repair by welding is allowed for casting / forging.
53
54
55
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 20 - 100
3 Specification ASME B16.34 / API 6D
4 Tag No. VBA32-R
5 Piping Class 3A3
6 Class 300
7
8 VALVE DESCRIPTION Ball Valve, Carbon Steel, CL 300, Flanged RF. Reduced Bore, Fire Safe,
9 Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti Blowout
10 Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension ASME B16.10
13 Bore Reduced
14 Bonnet / Adapter Fixing Bolted
15 Operation Lever Operated
16 Construction ball Seat supported
17 End Connections Class 300 Flanged Ends To ASME B16.5, Raised Face
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
21 Body/Bonnet/Adapter ASTM A 105 or A216 - WCB / WCC
22 Ball ASTM A 182 - F316 or A351 - CF8M
23 Trim/Stem ASTM A 182 - F316 or A705 - 630
24 Seats and Seals PTFE Seat Inserts, PTFE Seals
25 O-Ring ELAST-O-LION MINUS 40
26 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ASME B16.34
34 Temperature PLUS 0°C to PLUS 120° C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 4
41 - Seat Note 4
42 - Air Seat Note 4
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46 MATERIAL REQUIREMENTS
47
48 REMARKS
49 Notes:
50 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
51 2) Valve to be firesafe to API 6FA / API 607.
52 3) Valve to have body cavity pressure release
53 4) Test pressure shall be in accordance with ASME B16.34.
54 5) Ball position indicator shall be provided
55 6) Stem sealant injection shall be provided for valves 6" and larger, all sealant injection points shall incorporate a non return valve.
56 7) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
57 8) No repair by welding is allowed on castings/forgings
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 150 - 600
3 Specification ASME B16.34 / API 6D
4 Tag No. VBA32-RG
5 Piping Class 3A3
6 Class 300
7
8 VALVE DESCRIPTION Ball Valve, Carbon Steel, CL 300, Flanged RF. Reduced Bore, Fire Safe,
9 Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti Blowout
10 Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension ASME B16.34 / API 6D
13 Bore Reduced
14 Bonnet / Adapter Fixing Bolted
15 Operation Gear operated
16 Construction ball Trunnion supported
17 End Connections Class 300 Flanged Ends To ASME B16.5, Raised Face
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
21 Body/Bonnet/Adapter ASTM A 105 or A216 - WCB / WCC
22 Ball ASTM A 182 - F316 or A351 - CF8M
23 Trim/Stem ASTM A 182 - F316 or A705 - 630
24 Seats and Seals PTFE Seat Inserts, PTFE Seals
25 O-Ring ELAST-O-LION MINUS 40
26 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ASME B16.34
34 Temperature PLUS 0°C to PLUS 120° C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 4
41 - Seat Note 4
42 - Air Seat Note 4
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46 MATERIAL REQUIREMENTS
47
48 REMARKS
49 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
50 2) Valve to be firesafe to API 6FA / API 607.
51 3) Valve to have body cavity pressure release
52 4) Test pressure shall be in accordance with ASME B16.34.
53 5) Ball position indicator shall be provided
54 6) Stem sealant injection shall be provided for valve size DN 150 and larger, all sealant injection points shall incorporate a non return valve.
55 7) Valves shall be supplied with water jet proof gear operator.
56 8) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
57 9) No repair by welding is allowed on castings/forgings.
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 100
3 Specification ASME B16.34 / API 6D
4 Tag No. VBA32-F
5 Piping Class 3A3
6 Class 300
7
8 VALVE DESCRIPTION Ball Valve, Carbon Steel, CL 300, Flanged RF. Full Bore, Fire Safe,
9 Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti Blowout
10 Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension ASME B16.10
13 Bore Full Bore
14 Bonnet / Adapter Fixing Bolted
15 Operation Lever Operated
16 Construction ball Seat supported
17 End Connections Class 300 Flanged Ends To ASME B16.5, Raised Face
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
21 Body/Bonnet/Adapter ASTM A 105 or A216 - WCB / WCC
22 Ball ASTM A 182 - F316 or A351 - CF8M
23 Trim/Stem ASTM A 182 - F316 or A705 - 630
24 Seats and Seals PTFE Seat Inserts, PTFE Seals
25 O-Ring ELAST-O-LION MINUS 40
26 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ASME B16.34
34 Temperature PLUS 0°C to PLUS 120° C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 4
41 - Seat Note 4
42 - Air Seat Note 4
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46 MATERIAL REQUIREMENTS
47
48 REMARKS
49 Notes:
50 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
51 2) Valve to be firesafe to API 6FA / API 607.
52 3) Valve to have body cavity pressure release
53 4) Test pressure shall be in accordance with ASME B16.34.
54 5) Ball position indicator shall be provided
55 6) Stem sealant injection shall be provided for valves 6" and larger, all sealant injection points shall incorporate a non return valve.
56 7) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
57 8) No repair by welding is allowed on castings/forgings
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 150 - 600
3 Specification ASME B16.34 / API 6D
4 Tag No. VBA32-FG
5 Piping Class 3A3
6 Class 300
7
8 VALVE DESCRIPTION Ball Valve, Carbon Steel, CL 300, Flanged RF. Full Bore, Fire Safe,
9 Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti Blowout
10 Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension API 6D
13 Bore Full Bore
14 Bonnet / Adapter Fixing Bolted
15 Operation Gear operated
16 Construction ball Trunnion supported
17 End Connections Class 300 Flanged Ends To ASME B16.5, Raised Face
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
21 Body/Bonnet/Adapter ASTM A 105 or A216 - WCB / WCC
22 Ball ASTM A 182 - F316 or A351 - CF8M
23 Trim/Stem ASTM A 182 - F316 or A705 - 630
24 Seats and Seals PTFE Seat Inserts, PTFE Seals
25 O-Ring ELAST-O-LION MINUS 40
26 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ASME B16.34
34 Temperature PLUS 0°C to PLUS 120° C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 4
41 - Seat Note 4
42 - Air Seat Note 4
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46 MATERIAL REQUIREMENTS
47
48 REMARKS
49 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
50 2) Valve to be firesafe to API 6FA / API 607.
51 3) Valve to have body cavity pressure release
52 4) Test pressure shall be in accordance with ASME B16.34.
53 5) Ball position indicator shall be provided
54 6) Stem sealant injection shall be provided for valve size DN 150 and larger, all sealant injection points shall incorporate a non return valve.
55 7) Valves shall be supplied with water jet proof gear operator.
56 8) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
57 9) No repair by welding is allowed on castings/forgings.
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 40
3 Specification API 602
4 Tag No. VCA32
5 Piping Class 3A3
6 Class 300
7
8 VALVE TYPE Check -Piston Type
9
10
11 END CONNECTION AND RATING Flanged to ASME B16.5, raised face Class 300
12
13
14 MATERIAL
15 Gasket Manufacturer's Standard (Non Asbestos)
16 Body design Horizontal Flow, spring assisted, bolted bonnet
17 Body Material ASTM A 105 or A216 - WCB / WCC
18 Trim Design Metal to Metal Seats (Renewable)
19 Trim Material 13% Cr Steel
20 Packing Material NA
21 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
22
23 Spring ASTM B637 UNS N07750
24
25
26 VALVE OPERATOR NA
27
28
29 DESIGN CONDITIONS
30 Pressure Rating Class 300
31 Temperature
32 - Operating PLUS 0°C to PLUS 150° C
33
34
35 TESTS
36 Body Note 2
37 Seat Note 2
38
39
40 INSPECTION AND TESTING REQUIREMENT API 598
41
42 CERTIFICATION DIN 50049 - 3.1B for Body and Bonnet T/Cover
43
44
45 REMARKS
46 Notes:
47 1) Test duration shall be in accordance with API 6D.
48 2) Test pressure shall be in accordance with ASME B16.34.
49 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
50 4) No repair by welding is allowed for casting / forging.
51
52
53
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 600
3 Specification API 594
4 Tag No. VCA384
5 Piping Class 3A3
6 Class 300
7
8 VALVE TYPE Wafer Check, Dual Plate, (For use in the Horizontal or the
9 vertical with upward flow)
10
11 END CONNECTION AND RATING Suitable for mounting between ASME B16.5 raised
12 face class 300 lb flanges
13
14 MATERIAL
15 Gasket NA
16 Body design Wafer Type - Spring Loaded Dual Plate
17 Body Material
18 Forged A105, A352 LCB/LCC, A350 LF2
19 Cast A216 WCB/WCC
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification ASME B16.34
4 Tag No. VDA32
5 Piping Class 3A3
6 Class 300
7
8 VALVE TYPE
Integral Double Block (ball) & Bleed (needle), Fire safe
9
10
11 END CONNECTION AND RATING Inlet with ASME B16.5 300# RF, outlet 15 mm NPTF
12
13
14 MATERIAL
15 Valves, Body and Trim A105 with SS316 trim
16 Gland Packing Peek seat / Grafoil seal
17 Flange A105N
18 Packing Material NA
19 Bolting NA
20
21
22
23
24
25
26 VALVE OPERATOR Lever operated
27
28
29
30
31
32 DESIGN CONDITIONS
33 Pressure Pressure / Temperature ratings to ASME B16.34
34 Temperature PLUS 0°C to PLUS 120° C
35 - Operating
36
37 TESTS
38 Hydrostatic
39 Body Note 3
40 Seat Note 3
41
42 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
43 INSPECTION AND TESTING REQUIREMENT API 598
44
45
46 REMARKS
47 Notes:
48 1) Test duration shall be in accordance with API 6D.
49 2) Valve to be firesafe to API 6FA / API 607.
50 3) Test pressure shall be in accordance with ASME B16.34.
51 4) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
52 5) No repair by welding is allowed on castings/ forgings.
53
54
55
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification ASME B16.34
4 Tag No. VDA32-F
5 Piping Class 3A3
6 Class 300
7
8 VALVE TYPE
Integral Double Block (ball) & Bleed (needle), Fire safe
9
10
11 END CONNECTION AND RATING Inlet and outlet with ASME B16.5 300# RF
12
13
14 MATERIAL
15 Valves, Body and Trim A105 with SS316L trim
16 Gland Packing Peek seat / Grafoil seal
17 Flange A105
18 Packing Material NA
19 Bolting NA
20
21
22
23
24
25
26 VALVE OPERATOR Lever operated
27
28
29
30
31 DESIGN CONDITIONS
32 Pressure Pressure / Temperature ratings to ASME B16.34
33 Temperature PLUS 0°C to PLUS 120° C
34 - Operating
35
36 TESTS
37 Hydrostatic
38 Body Note 3
39 Seat Note 3
40 Pneumatic Note 3
41
42 INSPECTION AND TESTING REQUIREMENT API 598
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45
46 REMARKS
47 Notes:
48 1) Test duration shall be in accordance with API 6D.
49 2) Valve to be firesafe to API 6FA / API 607.
50 3) Test pressure shall be in accordance with ASME B16.34.
51 4) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
52
53
54
55
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 150 - 600
3 Specification API 609
4 Tag No. VTOA32-G
5 Piping Class 3A3
6 Class 300
7
8 VALVE TYPE Triple Offset Butterfly Valve, Wafer Lug Type, Fire Safe, Note 6
9 CS Body, SS316 Trim, Anti-blowout Stem
10
11 END CONNECTION AND RATING Suitable for mounting between ASME B16.5 raised face
12 CL 300lb flanges
13
14 MATERIAL
15 Body Material ASTM A216 WCB
16 Disk ASTM A216 WCB
17 Shaft / trunnion A276 Gr 316
18 Gland Plate AISI 316
19 Body Seat/Seal AISI 316
20 Disc Seat/Seal AISI 316
21 Mounting Plate Steel
21 Gaskets Graphite
22 Bearing AISI 316/hard chrome plated
23 Packing Graphite passivated
24 Bolting
Stainless Steel type 316
25
26
27 VALVE OPERATOR Gear Operated
28
29
30 DESIGN CONDITIONS
31 Pressure Pressure / Temperature ratings to ASME B16.34
32 Temperature PLUS 0°C to PLUS 120° C
33 - Operating
34
35 TESTS
36 Hydrostatic
37 Body Note 2
38 Seat Note 2
39 Pneumatic
40
41 INSPECTION AND TESTING REQUIREMENT API 598
42 MARKING API 609 / MSS SP-25
43 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
44
45 REMARKS
46 Notes:
47 1) Test duration shall be in accordance with API 6D and zero leakage for metal seat as stated in API 598.
48 2) Test pressure shall be in accordance with ASME B16.34.
49 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
50 4) No repair by welding is allowed for casting / forging.
51 5) Valve to be firesafe to API 6FA / API 607.
52 6) The threads of the lugs shall be drilled out to allow the studbolts to slide through.
53
54
55
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 200
3 Specification ASME B16.34 / API 6D
4 Tag No. VTY32
5 Piping Class 3A6
6 Class 300
7
8 VALVE TYPE Globe Valve (Straight Pattern)
9
10
11 END CONNECTION AND RATING 300#RF
12
13
14 MATERIAL
15 Gasket Manufacturer's Standard (Non Asbestos)
16 Body design Bolted Bonnet, Outside Srew and Yoke, Rising Stem
17 Body Material Forged or Cast Carbon Steel ASTM A105 or
18 ASTM A 216 GR WCB
19 Trim Design Plug Type Disc, Renewable Seat
20
21 Trim Material 13%Cr Steel Stem, Seat and Disc
22
23 Packing Material Manufacturer's Standard (Non Asbestos)
24
25 VALVE OPERATOR Handwheel
26
27 BOLTING
28 Bonnet & Gland
29 Studs ASTM A 193 GR B7 Fluorocarbon Coated
30 Nuts ASTM A194 GR 2H Fluorocarbon Coated
31
32
33
34
35 DESIGN CONDITIONS Pressure / Temperature ratings to ANSI B16.34
36 Plus 0°C to Plus 120 °C
37
38 TESTS
39 Hydrostatic
40 Body Note 2
41 Seat Note 2
42
43 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
44 INSPECTION AND TESTING REQUIREMENT API 598
45
46 REMARKS
47
48 Notes:
49 1) Test duration shall be in accordance with API 6D.
50 2) Test pressure shall be in accordance with ASME B16.34.
51 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
52 4) No repair by welding is allowed for casting / forging.
53
54
55
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 20 - 100
3 Specification ASME B16.34 / API 6D
4 Tag No. VBY32-R
5 Piping Class 3A6
6 Class 300
7
8 VALVE DESCRIPTION Ball Valve, Carbon Steel, CL 300, Flanged RF. Reduced Bore, Fire Safe,
9 Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti Blowout
10 Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension ASME B16.10
13 Bore Reduced
14 Bonnet / Adapter Fixing Bolted
15 Operation Lever Operated
16 Construction ball Seat supported
17 End Connections Class 300 Flanged Ends To ASME B16.5, Raised Face
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
21 Body/Bonnet/Adapter ASTM A 105 or A216 - WCB / WCC
22 Ball ASTM A 182 - F316 or A351 - CF8M
23 Trim/Stem ASTM A 182 - F316 or A705 - 630
24 Seats and Seals PTFE Seat Inserts, PTFE Seals
25 O-Ring ELAST-O-LION MINUS 40
26 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ANSI B16.34
34 Temperature PLUS 0°C to PLUS 120° C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 4
41 - Seat Note 4
42 - Air Seat Note 4
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46 MATERIAL REQUIREMENTS
47
48 REMARKS
49 Notes:
50 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
51 2) Valve to be firesafe to API 6FA / API 607.
52 3) Valve to have body cavity pressure release
53 4) Test pressure shall be in accordance with ASME B16.34.
54 5) Ball position indicator shall be provided
55 6) Stem sealant injection shall be provided for valves 6" and larger, all sealant injection points shall incorporate a non return valve.
56 7) Minimum thickness of valve bodies shall be in accordance with ASME B16.34 plus a corrosion allowance of 6mm.
57 8) No repair by welding is allowed on castings/forgings
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 150 - 600
3 Specification ASME B16.34 / API 6D
4 Tag No. VBY32-RG
5 Piping Class 3A6
6 Class 300
7
8 VALVE DESCRIPTION Ball Valve, Carbon Steel, CL 300, Flanged RF. Reduced Bore, Fire Safe,
9 Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti Blowout
10 Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension API 6D
13 Bore Reduced
14 Bonnet / Adapter Fixing Bolted
15 Operation Gear operated
16 Construction ball Trunnion supported
17 End Connections Class 300 Flanged Ends To ASME B16.5, Raised Face
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
21 Body/Bonnet/Adapter ASTM A 105 or A216 - WCB / WCC
22 Ball ASTM A 182 - F316 or A351 - CF8M
23 Trim/Stem ASTM A 182 - F316 or A705 - 630
24 Seats and Seals PTFE Seat Inserts, PTFE Seals
25 O-Ring ELAST-O-LION MINUS 40
26 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ANSI B16.34
34 Temperature PLUS 0°C to PLUS 120° C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 4
41 - Seat Note 4
42 - Air Seat Note 4
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46 MATERIAL REQUIREMENTS
47
48 REMARKS
49 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
50 2) Valve to be firesafe to API 6FA / API 607.
51 3) Valve to have body cavity pressure release
52 4) Test pressure shall be in accordance with ASME B16.34.
53 5) Ball position indicator shall be provided
54 6) Stem sealant injection shall be provided for valve size DN 150 and larger, all sealant injection points shall incorporate a non return valve.
55 7) Valves shall be supplied with water jet proof gear operator.
56 8) Minimum thickness of valve bodies shall be in accordance with ASME B16.34 plus a corrosion allowance of 6mm.
57 9) No repair by welding is allowed on castings/forgings.
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 100
3 Specification ASME B16.34 / API 6D
4 Tag No. VBY32-F
5 Piping Class 3A6
6 Class 300
7
8 VALVE DESCRIPTION Ball Valve, Carbon Steel, CL 300, Flanged RF. Full Bore, Fire Safe,
9 Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti Blowout
10 Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension ASME B16.10
13 Bore Full Bore
14 Bonnet / Adapter Fixing Bolted
15 Operation Lever Operated
16 Construction ball Seat supported
17 End Connections Class 300 Flanged Ends To ASME B16.5, Raised Face
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
21 Body/Bonnet/Adapter ASTM A 105 or A216 - WCB / WCC
22 Ball ASTM A 182 - F316 or A351 - CF8M
23 Trim/Stem ASTM A 182 - F316 or A705 - 630
24 Seats and Seals PTFE Seat Inserts, PTFE Seals
25 O-Ring ELAST-O-LION MINUS 40
26 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ANSI B16.34
34 Temperature PLUS 0°C to PLUS 120° C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 4
41 - Seat Note 4
42 - Air Seat Note 4
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46 MATERIAL REQUIREMENTS
47
48 REMARKS
49 Notes:
50 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
51 2) Valve to be firesafe to API 6FA / API 607.
52 3) Valve to have body cavity pressure release
53 4) Test pressure shall be in accordance with ASME B16.34.
54 5) Ball position indicator shall be provided
55 6) Stem sealant injection shall be provided for valves 6" and larger, all sealant injection points shall incorporate a non return valve.
56 7) Minimum thickness of valve bodies shall be in accordance with ASME B16.34 plus a corrosion allowance of 6mm.
57 8) No repair by welding is allowed on castings/forgings
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 150 - 600
3 Specification ASME B16.34 / API 6D
4 Tag No. VBY32-FG
5 Piping Class 3A6
6 Class 300
7
8 VALVE DESCRIPTION Ball Valve, Carbon Steel, CL 300, Flanged RF. Full Bore, Fire Safe,
9 Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti Blowout
10 Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension API 6D
13 Bore Full Bore
14 Bonnet / Adapter Fixing Bolted
15 Operation Gear operated
16 Construction ball Trunnion supported
17 End Connections Class 300 Flanged Ends To ASME B16.5, Raised Face
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
21 Body/Bonnet/Adapter ASTM A 105 or A216 - WCB / WCC
22 Ball ASTM A 182 - F316 or A351 - CF8M
23 Trim/Stem ASTM A 182 - F316 or A705 - 630
24 Seats and Seals PTFE Seat Inserts, PTFE Seals
25 O-Ring ELAST-O-LION MINUS 40
26 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ANSI B16.34
34 Temperature PLUS 0°C to PLUS 120° C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 4
41 - Seat Note 4
42 - Air Seat Note 4
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46 MATERIAL REQUIREMENTS
47
48 REMARKS
49 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
50 2) Valve to be firesafe to API 6FA / API 607.
51 3) Valve to have body cavity pressure release
52 4) Test pressure shall be in accordance with ASME B16.34.
53 5) Ball position indicator shall be provided
54 6) Stem sealant injection shall be provided for valve size DN 150 and larger, all sealant injection points shall incorporate a non return valve.
55 7) Valves shall be supplied with water jet proof gear operator.
56 8) Minimum thickness of valve bodies shall be in accordance with ASME B16.34 plus a corrosion allowance of 6mm.
57 9) No repair by welding is allowed on castings/forgings.
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 40
3 Specification API 602
4 Tag No. VCY32
5 Piping Class 3A6
6 Class 300
7
8 VALVE TYPE Check -Piston Type
9
10
11 END CONNECTION AND RATING Flanged to ASME B16.5, raised face Class 300
12
13
14 MATERIAL
15 Gasket Manufacturer's Standard (Non Asbestos)
16 Body design Horizontal Flow, spring assisted, bolted bonnet
17 Body Material ASTM A 105 or A216 - WCB / WCC
18 Trim Design Metal to Metal Seats (Renewable)
19 Trim Material 13% Cr Steel
20 Packing Material NA
21 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
22
23 Spring ASTM B637 UNS N07750
24
25
26 VALVE OPERATOR NA
27
28
29 DESIGN CONDITIONS
30 Pressure Rating Class 300
31 Temperature
32 - Operating PLUS 0°C to PLUS 150° C
33
34
35 TESTS
36 Body Note 2
37 Seat Note 2
38
39
40 INSPECTION AND TESTING REQUIREMENT API 598
41
42 CERTIFICATION DIN 50049 - 3.1B for Body and Bonnet T/Cover
43
44
45 REMARKS
46 Notes:
47 1) Test duration shall be in accordance with API 6D.
48 2) Test pressure shall be in accordance with ASME B16.34.
49 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34 plus a corrosion allowance of 6mm.
50 4) No repair by welding is allowed for casting / forging.
51
52
53
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 600
3 Specification API 594
4 Tag No. VCY384
5 Piping Class 3A6
6 Class 300
7
8 VALVE TYPE Wafer Lug Check, Dual Plate, (For use in the Horizontal or
9 the vertical with upward flow)
10
11 END CONNECTION AND RATING Suitable for mounting between ASME B16.5 raised
12 face class 300 lb flanges
13
14 MATERIAL
15 Gasket NA
16 Body design Wafer Type - Spring Loaded Dual Plate
17 Body Material
18 Forged A105, A352 LCB/LCC, A350 LF2
19 Cast A216 WCB/WCC
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification ASME B16.34
4 Tag No. VDY32
5 Piping Class 3A6
6 Class 300
7
8 VALVE TYPE
Integral Double Block (ball) & Bleed (needle), Fire safe
9
10
11 END CONNECTION AND RATING Inlet with ASME B16.5 300# RF, outlet 15 mm NPTF
12
13
14 MATERIAL
15 Valves, Body and Trim A105 with SS316 trim
16 Gland Packing Peek seat / Grafoil seal
17 Flange A105
18 Packing Material NA
19 Bolting NA
20
21
22
23
24
25
26 VALVE OPERATOR Lever operated
27
28
29
30
31
32 DESIGN CONDITIONS
33 Pressure Pressure / Temperature ratings to ANSI B16.34
34 Temperature PLUS 0°C to PLUS 120° C
35 - Operating
36
37 TESTS
38 Hydrostatic
39 Body Note 3
40 Seat Note 3
41
42 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
43 INSPECTION AND TESTING REQUIREMENT API 598
44
45
46 REMARKS
47 Notes:
48 1) Test duration shall be in accordance with API 6D.
49 2) Valve to be firesafe to API 6FA / API 607.
50 3) Test pressure shall be in accordance with ASME B16.34.
51 4) Minimum thickness of valve bodies shall be in accordance with ASME B16.34 plus a corrosion allowance of 6mm.
52 5) No repair by welding is allowed on castings/ forgings.
53
54
55
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification ASME B16.34
4 Tag No. VDY32-F
5 Piping Class 3A6
6 Class 300
7
8 VALVE TYPE
Integral Double Block (ball) & Bleed (needle), Fire safe
9
10
11 END CONNECTION AND RATING Inlet and outlet with ASME B16.5 300# RF
12
13
14 MATERIAL
15 Valves, Body and Trim A105 with SS316L trim
16 Gland Packing Peek seat / Grafoil seal
17 Flange A105
18 Packing Material NA
19 Bolting NA
20
21
22
23
24
25
26 VALVE OPERATOR Lever operated
27
28
29
30
31 DESIGN CONDITIONS
32 Pressure Pressure / Temperature ratings to ANSI B16.34
33 Temperature PLUS 0°C to PLUS 120° C
34 - Operating
35
36 TESTS
37 Hydrostatic
38 Body Note 3
39 Seat Note 3
40 Pneumatic Note 3
41
42 INSPECTION AND TESTING REQUIREMENT API 598
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45
46 REMARKS
47 Notes:
48 1) Test duration shall be in accordance with API 6D.
49 2) Valve to be firesafe to API 6FA / API 607.
50 3) Test pressure shall be in accordance with ASME B16.34.
51 4) Minimum thickness of valve bodies shall be in accordance with ASME B16.34 plus a corrosion allowance of 6mm.
52
53
54
55
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 150 - 600
3 Specification API 609
4 Tag No. VTOY32-G
5 Piping Class 3A6
6 Class 300
7
8 VALVE TYPE Triple Offset Butterfly Valve, Wafer Lug Type, Fire Safe, Note 6
9 CS Body, SS316 Trim, Anti-blowout Stem
10
11 END CONNECTION AND RATING Suitable for mounting between ASME B16.5 raised face
12 CL 300lb flanges
13
14 MATERIAL
15 Body Material ASTM A216 WCB
16 Disk ASTM A216 WCB
17 Shaft / trunnion A276 Gr 316
18 Gland Plate AISI 316
19 Body Seat/Seal AISI 316
20 Disc Seat/Seal AISI 316
21 Mounting Plate Steel
21 Gaskets Graphite
22 Bearing AISI 316/hard chrome plated
23 Packing Graphite passivated
24 Bolting
Stainless Steel type 316
25
26
27 VALVE OPERATOR Gear Operated
28
29
30 DESIGN CONDITIONS
31 Pressure Pressure / Temperature ratings to ANSI B16.34
32 Temperature PLUS 0°C to PLUS 120° C
33 - Operating
34
35 TESTS
36 Hydrostatic
37 Body Note 2
38 Seat Note 2
39 Pneumatic
40
41 INSPECTION AND TESTING REQUIREMENT API 598
42 MARKING API 609 / MSS SP-25
43 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
44
45 REMARKS
46 Notes:
47 1) Test duration shall be in accordance with API 6D and zero leakage for metal seat as stated in API 598.
48 2) Test pressure shall be in accordance with ASME B16.34.
49 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34 plus a corrosion allowance of 6mm.
50 4) No repair by welding is allowed for casting / forging.
51 5) Valve to be firesafe to API 6FA / API 607.
52 6) The threads of the lugs shall be drilled out to allow the studbolts to slide through.
53
54
55
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 100
3 Specification ASME B16.34 / API 6D
4 Tag No. VTA153
5 Piping Class 15A3
6 Class 1500
7
8 VALVE TYPE Globe Valve (Straight Pattern)
9
10
11 END CONNECTION AND RATING 1500# RTJ
12
13
14 MATERIAL
15 Gasket Manufacturer's Standard (Non Asbestos)
16 Body design Bolted Bonnet, Outside Srew and Yoke, Rising Stem
17 Body Material Forged Carbon Steel ASTM A105 / A216 Gr WCB
18
19 Trim Design Plug Type Disc, Renewable Seat
20
21 Trim Material 13% Cr Steel Stem, Seat and Disc
22
23 Packing Material Manufacturer's Standard (Non Asbestos)
24
25 VALVE OPERATOR Handwheel
26
27 BOLTING
28 Bonnet & Gland
29 Studs ASTM A 193 GR B7 Fluorocarbon coated
30 Nuts ASTM A194 GR 2H Fluorocarbon coated
31
32 SERVICE
33
34
35
36
37 DESIGN CONDITIONS Pressure / Temperature ratings to ANSI B16.34
38 Plus 0°C to Plus 120 °C
39
40 TESTS
41 Body Note 2
42 Seat Note 2
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45
46 REMARKS
47
48 Notes:
49 1) Test duration shall be in accordance with API 6D.
50 2) Test pressure shall be in accordance with ASME B16.34.
51 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
52 4) No repair by welding is allowed for casting / forging.
53
54
55
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 25 - 50
3 Specification ASME B16.34 / API 6D
4 Tag No. VBA153-R
5 Piping Class 15A3
6 Class 1500
7
8 VALVE DESCRIPTION Ball Valve, Carbon Steel, CL 1500, Flanged RTJ. Reduced Bore, Fire
9 Safe, Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti
10 Blowout Stem, Anti-Static Device.
11 GENERAL
12 Face to Face DIM ASME B16.10 Table 1 Column 19
13 Bore Reduced
14 Bonnet / Adapter Fixing Bolted
15 Operation Lever Operated
16 Construction ball Seat supported
17 End Connections Class 1500 Flanged Ends To ASME B16.5, Ring Type Joint
18 Flange Finish Gasket Groove Contact Surface Finish 1.6 Micrometres Ra maximum In
19 accordance with ANSI B46.1
20 MATERIAL
21 Body/Bonnet/Adapter ASTM A105, A216 - WCB / WCC
22 Ball ASTM A105, A216 - WCB / WCC plus 5 mil ENP
23 Trim/Stem ASTM A 182 - F316 or A706 - 630
24 Seats and Seals PEEK
25 O-Ring VITON
26 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ANSI B16.34
34 Temperature PLUS 0°C to PLUS 120° C
35 - Operating
36 - Blowdown -
37 Service Hydrocarbon, Fuel Gas
38
39 TESTS
40 Hydrostatic
41 - Body Note 4
42 - Seat Note 4
43 - Air Seat Note 4
44
45 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
46 INSPECTION In accordance with Purchase Order
47 MATERIAL REQUIREMENTS
48
49 REMARKS
50 Notes:
51 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
52 2) Valve to be firesafe to API 6FA / API 607.
53 3) Valve to have body cavity pressure release
54 4) Test pressure shall be in accordance with ASME B16.34.
55 5) Ball position indicator shall be provided
56 6) Stem sealant injection shall be provided for valves 6" and larger, all sealant injection points shall incorporate a non return valve.
7) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
57 8) No repair by welding is allowed on castings/forgings
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 80 - 600
3 Specification ASME B16.34 / API 6D
4 Tag No. VBA153-RG
5 Piping Class 15A3
6 Class 1500
7
8 VALVE DESCRIPTION Ball Valve, Carbon Steel, CL 1500, Flanged RTJ. Reduced Bore, Fire
9 Safe, Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti
10 Blowout Stem, Anti-Static Device.
11 GENERAL
12 Face to Face DIM API 6D
13 Bore Reduced
14 Bonnet / Adapter Fixing Bolted
15 Operation Gear operated
16 Construction ball Trunnion supported
17 End Connections Class 1500 Flanged Ends To ASME B16.5, Ring Type Joint
18 Flange Finish Gasket Groove Contact Surface Finish 1.6 Micrometres Ra maximum In
19 accordance with ANSI B46.1
20 MATERIAL
21 Body/Bonnet/Adapter ASTM A105 or A216 - WCB / WCC
22 Ball ASTM A105, A216 - WCB / WCC plus 5 mil ENP
23 Trim/Stem ASTM A 182 - F316 or A706 - 830
24 Seats and Seals PEEK
25 O-Ring VITON
26 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ANSI B16.34
34 Temperature PLUS 0°C to PLUS 120° C
35 - Operating
36 - Blowdown -
37 Service Hydrocarbon, Fuel Gas
38
39 TESTS
40 Hydrostatic
41 - Body Note 4
42 - Seat Note 4
43 - Air Seat Note 4
44
45 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
46 INSPECTION In accordance with Purchase Order
47 MATERIAL REQUIREMENTS
48
49 REMARKS
50 Notes:
51 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
52 2) Valve to be firesafe to API 6FA / API 607.
53 3) Valve to have body cavity pressure release
54 4) Test pressure shall be in accordance with ASME B16.34.
55 5) Ball position indicator shall be provided
56 6) Stem sealant injection shall be provided for valves 6" and larger, all sealant injection points shall incorporate a non return valve.
57 7) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
58 8) No repair by welding is allowed on castings/forgings
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 25 - 50
3 Specification ASME B16.34 / API 6D
4 Tag No. VBA153-F
5 Piping Class 15A3
6 Class 1500
7
8 VALVE DESCRIPTION Ball Valve, Carbon Steel, CL 1500, Flanged RTJ. Full Bore, Fire Safe,
9 Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti Blowout
10 Stem, Anti-Static Device.
11 GENERAL
12 Face to Face DIM ASME B16.10 Table 1 Column 19
13 Bore Full Bore
14 Bonnet / Adapter Fixing Bolted
15 Operation Lever Operated
16 Construction ball Seat supported
17 End Connections Class 1500 Flanged Ends To ASME B16.5, Ring Type Joint
18 Flange Finish Gasket Groove Contact Surface Finish 1.6 Micrometres Ra maximum In
19 accordance with ANSI B46.1
20 MATERIAL
21 Body/Bonnet/Adapter ASTM A105 or A216 - WCB / WCC
22 Ball ASTM A105, A216 - WCB / WCC plus 5 mil ENP
23 Trim/Stem ASTM A 182 - F316 or A706 - 830
24 Seats and Seals PEEK
25 O-Ring VITON
26 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ANSI B16.34
34 Temperature PLUS 0°C to PLUS 120° C
35 - Operating
36 - Blowdown -
37 Service Hydrocarbon, Fuel Gas
38
39 TESTS
40 Hydrostatic
41 - Body Note 4
42 - Seat Note 4
43 - Air Seat Note 4
44
45 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
46 INSPECTION In accordance with Purchase Order
47 MATERIAL REQUIREMENTS
48
49 REMARKS
50 Notes:
51 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
52 2) Valve to be firesafe to API 6FA / API 607.
53 3) Valve to have body cavity pressure release
54 4) Test pressure shall be in accordance with ASME B16.34.
55 5) Ball position indicator shall be provided
56 6) Stem sealant injection shall be provided for valves 6" and larger, all sealant injection points shall incorporate a non return valve.
57 7) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
58 8) No repair by welding is allowed on castings/forgings
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 80 - 600
3 Specification ASME B16.34 / API 6D
4 Tag No. VBA153-FG
5 Piping Class 15A3
6 Class 1500
7
8 VALVE DESCRIPTION Ball Valve, Carbon Steel, CL 1500, Flanged RTJ. Full Bore, Fire Safe,
9 Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti Blowout
10 Stem, Anti-Static Device.
11 GENERAL
12 Face to Face DIM API 6D
13 Bore Full Bore
14 Bonnet / Adapter Fixing Bolted
15 Operation Gear operated
16 Construction ball Trunnion supported
17 End Connections Class 1500 Flanged Ends To ASME B16.5, Ring Type Joint
18 Flange Finish Gasket Groove Contact Surface Finish 1.6 Micrometres Ra maximum In
19 accordance with ANSI B46.1
20 MATERIAL
21 Body/Bonnet/Adapter ASTM A105 or A216 - WCB / WCC
22 Ball ASTM A105, A216 - WCB / WCC plus 5 mil ENP
23 Trim/Stem ASTM A 182 - F316 or A706 - 830
24 Seats and Seals PEEK
25 O-Ring VITON
26 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ANSI B16.34
34 Temperature PLUS 0°C to PLUS 120° C
35 - Operating
36 - Blowdown -
37 Service Hydrocarbon, Fuel Gas
38
39 TESTS
40 Hydrostatic
41 - Body Note 4
42 - Seat Note 4
43 - Air Seat Note 4
44
45 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
46 INSPECTION In accordance with Purchase Order
47 MATERIAL REQUIREMENTS
48
49 REMARKS
50 Notes:
51 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
52 2) Valve to be firesafe to API 6FA / API 607.
53 3) Valve to have body cavity pressure release
54 4) Test pressure shall be in accordance with ASME B16.34.
55 5) Ball position indicator shall be provided
56 6) Stem sealant injection shall be provided for valves 6" and larger, all sealant injection points shall incorporate a non return valve.
57 7) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
58 8) No repair by welding is allowed on castings/forgings
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 40
3 Specification API 602
4 Tag No. VCA153
5 Piping Class 15A3
6 Class 1500
7
8 VALVE TYPE Check -Piston Type
9
10
11 END CONNECTION AND RATING Flanged to ASME B16.5, RTJ Class 1500
12
13
14 MATERIAL
15 Gasket Manufacturer's Standard (Non Asbestos)
16 Body design Horizontal Flow, spring assisted, bolted bonnet
17 Body Material ASTM A 105 or A216 - WCB / WCC
18 Trim Design Metal to Metal Seats (Renewable)
19 Trim Material 13% Cr Steel
20 Packing Material NA
21 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
22
23 Spring ASTM B637 UNS N07750
24
25
26 VALVE OPERATOR NA
27
28
29 DESIGN CONDITIONS
30 Pressure Rating Class 1500
31 Temperature
32 - Operating PLUS 0°C to PLUS 150° C
33
34
35 TESTS
36 Body Note 2
37 Seat Note 2
38
39
40 INSPECTION AND TESTING REQUIREMENT API 598
41
42 CERTIFICATION DIN 50049 - 3.1B for Body and Bonnet T/Cover
43
44
45 REMARKS
46 Notes:
47 1) Test duration shall be in accordance with API 6D.
48 2) Test pressure shall be in accordance with ASME B16.34.
49 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
50 4) No repair by welding is allowed for casting / forging.
51
52
53
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 25 - 600
3 Specification API 594
4 Tag No. VCA1584
5 Piping Class 15A3
6 Class 1500
7
8 VALVE TYPE Wafer Lug Check, Dual Plate, (For use in the Horizontal or
9 the vertical with upward flow)
10
11 END CONNECTION AND RATING Suitable for mounting between ASME B16.5 Ring Type
12 joint face class 1500 lb flanges
13
14 MATERIAL
15 Gasket NA
16 Body design Wafer Type - Spring Loaded Dual Plate
17 Body Material
18 Forged A105, A352 LCB/LCC, A350 LF2
19 Cast A216 WCB/WCC
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification ASME B16.34
4 Tag No. VDA153
5 Piping Class 15A3
6 Class 1500
7
8 VALVE TYPE Integral Double Block (O.S&Y needle) & Bleed (needle),
9 Fire safe
10
11 END CONNECTION AND RATING Inlet with ASME B16.5 1500# RTJ, 2 off 15mm NPTF outlet
12 connections, one located in the centre of the monoflange,
13 the other on the edge of the monoflange, edge connection
14 fitted with a 6000# plug
15
16 MATERIAL
17 Valves, Body and Trim A105 with SS316L trim
18 Gland Packing Peek seat / Grafoil seal
19 Flange A105
Packing Material NA
20 Bolting ASTM A 193 B7 / A194 2H
21
22
23
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification ASME B16.34
4 Tag No. VDA153-F
5 Piping Class 15A3
6 Class 1500
7
8 VALVE TYPE
Integral Double Block (ball) & Bleed (needle), Fire safe
9
10
11 END CONNECTION AND RATING Inlet and outlet with ASME B16.5 1500# RTJ
12
13
14 MATERIAL
15 Valves, Body and Trim A105 with SS316 trim
16 Gland Packing Peak seat / Grafoil seal
17 Flange A105
18 Packing Material NA
19 Bolting NA
20
21
22
23 VALVE OPERATOR Lever operated
24
25
26
27 SERVICE
28
29 DESIGN CONDITIONS
30 Pressure Pressure / Temperature ratings to ANSI B16.34
31 Temperature PLUS 0°C to PLUS 120° C
32 - Operating
33
34 TESTS
35 Hydrostatic
36 Body Note 3
37 Seat Note 3
38 Pneumatic Note 3
39
40 INSPECTION AND TESTING REQUIREMENT API 598
41
42 CERTIFICATION EN 10204 - 3.1B for all pressure containing parts
43
44
45
46 REMARKS
47 Notes:
48 1) Test duration shall be in accordance with API 6D.
49 2) Valve to be firesafe to API 6FA / API 607.
50 3) Test pressure shall be in accordance with ASME B16.34.
51 4) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
52 5) No repair by welding is allowed on castings/ forgings.
53
54
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 200
3 Specification ASME B16.34 / API 6D
4 Tag No. VTH11
5 Piping Class 1PX1, 1CN1
6 Class 150
7
8 VALVE TYPE Globe Valve (Straight Pattern)
9
10
11 END CONNECTION AND RATING Flanged to ASME B16.5, flat face Class 150
12
13
14 MATERIAL
15 Gasket Manufacturer's Standard (Non Asbestos)
16 Body design Bolted Bonnet, Outside Screw and Yoke, Rising Stem
17 Body Material BS1400 AB2
18
19 Trim Design Plug Type Disc, Renewable Seat
20
21 Trim Material Monel K400
22
23 Packing Material Manufacturer's Standard (Non Asbestos)
24
25 VALVE OPERATOR Handwheel
26
27 BOLTING
28 Bonnet & Gland
29 Studs ASTM A 193 GR B7 Fluorocarbon Coated
30 Nuts ASTM A194 GR 2H Fluorocarbon Coated
31
32
33
34
35 DESIGN CONDITIONS Pressure / Temperature ratings to ASME B16.34
36 Plus 0°C to Plus 120 °C
37
38 TESTS
39 Hydrostatic
40 Body Note 2
41 Seat Note 2
42
43 INSPECTION AND TESTING REQUIREMENT API 598
44
45 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
46
47 REMARKS
48
49 Notes:
50 1) Test duration shall be in accordance with API 6D.
51 2) Test pressure shall be in accordance with ASME B16.34.
52 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
53 4) No repair by welding is allowed for casting / forging.
54
55
56
57
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 200
3 Specification ASME B16.34 / API 6D
4 Tag No. VGH11
5 Piping Class 1PX1, 1CN1
6 Class
7
8 VALVE TYPE GATE
9
10
11 END CONNECTION AND RATING Flanged ASME B16.5 150 lb Flat Face
12
13
14 MATERIAL
15 Gasket Manufacturer's Standard (Non Asbestos)
16 Body design Bolted Bonnet, Outside Srew and Yoke, Rising Stem
17 Body Material BS1400 AB2
18
19 Trim Design Solid wedge full bore disc renewable seat rings
20 (see Note 6)
21 Trim Material MONEL K400
22
23 Packing Material Manufacturer's Standard (Non Asbestos)
24
25 VALVE OPERATOR ½ " - 12" Handwheel
26
27 BOLTING
28 Bonnet & Gland
29 Studs ASTM A 193 GR B7 Fluorocarbon coated
30 Nuts ASTM A194 GR 2H Fluorocarbon coated
31
32 SERVICE Seawater
33
34
35 DESIGN CONDITIONS Pressure / Temperature ratings to ASME B16.34
36 Plus 0°C to Plus 120 °C
37
38 TESTS
39 Body Note 2
40 Seat Note 2
41
42 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
43
44
45 REMARKS
46
47
48 Notes:
49 1) Test duration shall be in accordance with API 6D.
50 2) Test pressure shall be in accordance with ASME B16.34.
51 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
52 4) No repair by welding is allowed for casting / forging.
53
54
55
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 50 - 150
3 Specification API 609
4 Tag No. VFH183
5 Piping Class 1PX1, 1CN1
6 Class 150
7
8 VALVE TYPE Wafer Lug Type with through bolting Note 5
9
10
11 END CONNECTION AND RATING Suitable for mounting between ASME B16.5 flat
12 face class 150 lb flanges
13
14 MATERIAL
15 Body Material BS1400 AB2
16 Disk BS1400 AB2
17 Shaft / trunnion Monel K400
18 Gland Monel K400
19 Seal PTFE
20 Seat Monel K400
21 Gasket Spiral Wound, Non-Asbestos, oil resistant
22 Bearing Monel K400
23 Packing *
24 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, and Fluorocarbon Coated
25
26
27 VALVE OPERATOR Lever Operated
28
29
30
31 SERVICE Sea Water
32
33 DESIGN CONDITIONS
34 Pressure Pressure / Temperature ratings to ASME B16.34
35 Temperature PLUS 0°C to PLUS 120° C
36 - Operating
37
38 TESTS
39 Hydrostatic
40 Body Note 2
41 Seat Note 2
42 Pneumatic Note 2
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 REMARKS
46
47 Notes:
48 1) Test duration shall be in accordance with API 6D.
49 2) Test pressure shall be in accordance with ASME B16.34.
50 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
51 4) No repair by welding is allowed for casting / forging.
52 5) The threads of the lugs shall be drilled out to allow the studbolts to slide through.
53
54
55
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 200 - 600
3 Specification API 609
4 Tag No. VFH183-G
5 Piping Class 1PX1, 1CN1
6 Class 150
7
8 VALVE TYPE Wafer Lug Type with through bolting Note 5
9
10
11 END CONNECTION AND RATING Suitable for mounting between ASME B16.5 flat
12 face class 150 lb flanges
13
14 MATERIAL
15 Body Material BS1400 AB2
16 Disk BS1400 AB2
17 Shaft / trunnion Monel K400
18 Gland Monel K400
19 Seal PTFE
20 Seat Monel K400
21 Gasket Spiral Wound, Non-Asbestos, oil resistant
22 Bearing Monel K400
23 Packing By Vendor
24 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
25
26
27 VALVE OPERATOR Gear Operated
28
29
30
31 SERVICE Sea Water
32
33 DESIGN CONDITIONS
34 Pressure Pressure / Temperature ratings to ASME B16.34
35 Temperature PLUS 0°C to PLUS 120° C
36 - Operating
37
38 TESTS
39 Hydrostatic
40 Body Note 2
41 Seat Note 2
42 Pneumatic Note 2
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 REMARKS
46
47 Notes:
48 1) Test duration shall be in accordance with API 6D.
49 2) Test pressure shall be in accordance with ASME B16.34.
50 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
51 4) No repair by welding is allowed for casting / forging.
52 5) The threads of the lugs shall be drilled out to allow the studbolts to slide through.
53
54
55
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 40
3 Specification API 602
4 Tag No. VCH12
5 Piping Class 1PX1, 1CN1
6 Class 150
7
8 VALVE TYPE Check -Piston Type
9
10
11 END CONNECTION AND RATING Flanged to ASME B16.5, raised face Class 150
12
13
14 MATERIAL
15 Gasket Manufacturer's Standard (Non Asbestos)
16 Body design Horizontal Flow, spring assisted, bolted bonnet
17 Body Material BS1400 AB2
18 Trim Design Metal to Metal Seats (Renewable)
19 Trim Material BS1400 AB2
20 Packing Material NA
21 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
22
23 Spring ASTM B637 UNS N07750
24
25
26 VALVE OPERATOR NA
27
28
29 DESIGN CONDITIONS
30 Pressure Rating Class 150
31 Temperature
32 - Operating PLUS 0°C to PLUS 150° C
33
34
35 TESTS
36 Body Note 2
37 Seat Note 2
38
39
40 INSPECTION AND TESTING REQUIREMENT API 598
41
42 CERTIFICATION DIN 50049 - 3.1B for Body and Bonnet T/Cover
43
44
45 REMARKS
46 Notes:
47 1) Test duration shall be in accordance with API 6D.
48 2) Test pressure shall be in accordance with ASME B16.34.
49 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
50 4) No repair by welding is allowed for casting / forging.
51
52
53
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 50 - 600
3 Specification API 594
4 Tag No. VCH184
5 Piping Class 1PX1, 1CN1
6 Class 150
7
8 VALVE TYPE Wafer Check, Dual Plate, (For use in the Horizontal or the
9 vertical with upward flow)
10
11 END CONNECTION AND RATING Suitable for mounting between ASME B16.5 flat
12 face class 150 lb flanges
13
14 MATERIAL
15 Gasket NA
16 Body design Wafer Type - Spring Loaded Dual Plate
17 Body Material
18 Forged BS1400 AB2
19 Cast
20
21 Trim Design Metal to Metal seats (Integral)
22
23 Trim Material Monel K400 , NBR seat
24 hinge and stop pins, B471 UNS N08020 springs
25
26 Packing Material NA
27
28 VALVE OPERATOR NA
29
30 BOLTING NA
31 Bonnet & Gland
32 Stud
33 Nuts
34
35 SERVICE
36
37 DESIGN CONDITIONS
38 Pressure Pressure / Temperature ratings to ASME B16.34
39 Temperature PLUS 0°C to PLUS 120° C
40 - Operating
41 TESTS
42 Hydrostatic
43 Body Note 2
44 Seat Note 2
45 Pneumatic Note 2
46
47 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
48 REMARKS
49
50 Notes:
51 1) Test duration shall be in accordance with API 6D.
52 2) Test pressure shall be in accordance with ASME B16.34.
53 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
54 4) No repair by welding is allowed for casting / forging.
55
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 150 - 600
3 Specification API 609
4 Tag No. VTODT01-G
5 Piping Class 1PX1, 1CN1
6 Class 150
7
8 VALVE TYPE Triple Offset Butterfly Valve, Wafer Lug Type, NiAlBr Note 5
9 Body, Monel K500 Trim, Anti-blowout Stem
10
11 END CONNECTION AND RATING Suitable for mounting between ASME B16.5 flat face CL
12 150lb flanges
13
14 MATERIAL
15 Body Material BS1400 AB2
16 Disk BS1400 AB2
17 Shaft / trunnion Monel K400
18 Gland Plate AISI 316
19 Body Seat/Seal Laminated Monel 400/Graphite
20 Disc Seat/Seal BS1400 AB2
21 Mounting Plate Steel
22 Gaskets Graphite
23 Bearing AISI 316/hard chrome plated
24 Packing Graphite passivated
25 Bolting
Monel K400
26
27
28 VALVE OPERATOR Gear Operated
29
30
31 DESIGN CONDITIONS
32 Pressure Pressure / Temperature ratings to ASME B16.34
33 Temperature PLUS 0°C to PLUS 120° C
34 - Operating
35
36 TESTS
37 Hydrostatic
38 Body Note 2
39 Seat Note 2
40 Pneumatic
41
42 INSPECTION AND TESTING REQUIREMENT API 598
43 MARKING API 609 / MSS SP-25
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45
46 REMARKS
47 Notes:
48 1) Test duration shall be in accordance with API 6D and zero leakage for metal seat as stated in API 598.
49 2) Test pressure shall be in accordance with ASME B16.34.
50 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
51 4) No repair by welding is allowed for casting / forging.
52 5) The threads of the lugs shall be drilled out to allow the studbolts to slide through.
53
54
55
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification ASME B16.34
4 Tag No. VDH183
5 Piping Class 1PX1 / 1CN1
6 Class 150
7
8 VALVE TYPE Integral Double Block (O.S&Y needle) & Bleed (needle),
9 Fire safe
10
11 END CONNECTION AND RATING Inlet with ASME B16.5 150# FF, 2 off 15mm NPTF outlet
12 connections, one located in the centre of the monoflange,
13 the other on the edge of the monoflange, edge connection
14 fitted with a 3000# plug
15
16 MATERIAL
17 Valves, Body and Trim MONEL M400 WITH UNS 32760 TRIM
18 Gland Packing Peek seat / Grafoil seal
19 Flange MONEL M400
20 Packing Material NA
21 Bolting SS 316
22
23 VALVE OPERATOR Handwheel
24
25 DESIGN CONDITIONS
26 Pressure Pressure / Temperature ratings to ASME B16.34
27 Temperature 0°C to PLUS 120° C
28 - Operating
29
30 TESTS
31 Hydrostatic
32 Body Note 3
33 Seat Note 3
34 Pneumatic Note 3
35
36 INSPECTION AND TESTING REQUIREMENT API 598
37
38 CERTIFICATION EN 10204 - 3.1B for all pressure containing parts
39
40 REMARKS
41 Notes:
42 1) Test duration shall be in accordance with API 6D.
43 2) Valve to be firesafe to API 6FA / API 607.
44 3) Test pressure shall be in accordance with ASME B16.34.
45 4) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
46 5) No repair by welding is allowed on castings/ forgings.
##
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification ANSI B16.34
4 Tag No. VDD12-F
5 Piping Class 1S1
6 Class 150
7
8 VALVE TYPE
Integral Double Block (ball) & Bleed (needle), Fire safe
9
10
11 END CONNECTION AND RATING Inlet and outlet with ASME B16.5 150# RF
12
13
14 MATERIAL
15 Valves, Body and Trim ASTM A 182 - F316L or A351 - CF8M
16 Gland Packing Peak seat / Grafoil seal
17 Flange ASTM A 182 - F316L or A351 - CF8M
18 Packing Material NA
19 Bolting NA
20
21
22
23
24
25
26
27
28 VALVE OPERATOR Lever operated
29
30
31
32
33 DESIGN CONDITIONS
34 Pressure Pressure / Temperature ratings to ASME B16.34
35 Temperature Minus 50°C to Plus 150 °C
36 - Operating
37
38 TESTS
39 Hydrostatic
40 Body Note 3
41 Seat Note 3
42 Pneumatic Note 3
43
44 INSPECTION AND TESTING REQUIREMENT API 598
45
46 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
47
48 REMARKS
49 Notes:
50 1) Test duration shall be in accordance with API 6D.
51 2) Valve to be firesafe to API 6FA / API 607.
52 3) Test pressure shall be in accordance with ASME B16.34.
53 4) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
54 5) No repair in welding is allowed on casting / forging.
55
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification ASME B16.34
4 Tag No. VDD32
5 Piping Class 3S1
6 Class 300
7
8 VALVE TYPE Integral Double Block (O.S&Y needle) & Bleed (needle), Fire
9 safe
10
11 END CONNECTION AND RATING Inlet with ASME B16.5 300# RF, 2 off 15mm NPTF outlet
12 connections, one located in the centre of the monoflange,
13 the other on the edge of the monoflange, edge connection
14 fitted with a 3000# plug
15
16 MATERIAL
17 Valves, Body and Trim ASTM A 182 - F316L or A351 - CF8M
18 Gland Packing Peak seat / Grafoil seal
19 Flange ASTM A 182 - F316L or A351 - CF8M
20 Packing Material NA
21 Bolting NA
22
23
24
25
26 VALVE OPERATOR Handwheel
27
28
29 DESIGN CONDITIONS
30 Pressure Pressure / Temperature ratings to ANSI B16.34
31 Temperature Minus 50°C to Plus 150 °C
32 - Operating
33
34 TESTS
35 Hydrostatic
36 Body Note 3
37 Seat Note 3
38 Pneumatic Note 3
39
40 INSPECTION AND TESTING REQUIREMENT API 598
41
42 CERTIFICATION EN 10204 - 3.1B for all pressure containing parts
43
44 INSPECTION AND TESTING REQUIREMENT API 598
45
46
47
48 REMARKS
49 Notes:
50 1) Test duration shall be in accordance with API 6D.
51 2) Valve to be firesafe to API 6FA / API 607.
52 3) Test pressure shall be in accordance with ASME B16.34.
53 4) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
54 5) No repair by welding is allowed on castings/ forgings.
55
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification ASME B16.34
4 Tag No. VDD32-F
5 Piping Class 3S1
6 Class 300
7
8 VALVE TYPE
Integral Double Block (ball) & Bleed (needle), Fire safe
9
10
11 END CONNECTION AND RATING Inlet and outlet with ASME B16.5 300# RF
12
13
14 MATERIAL
15 Valves, Body and Trim ASTM A 182 - F316L or A351 - CF8M
16 Gland Packing Peak seat / Grafoil seal
17 Flange ASTM A 182 - F316L or A351 - CF8M
18 Packing Material NA
19 Bolting NA
20
21
22
23
24 VALVE OPERATOR Lever operated
25
26
27
28
29
30
31 DESIGN CONDITIONS
32 Pressure Pressure / Temperature ratings to ANSI B16.34
33 Temperature Minus 50°C to Plus 150 °C
34 - Operating
35
36 TESTS
37 Hydrostatic
38 Body Note 3
39 Seat Note 3
40
41 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
42 INSPECTION AND TESTING REQUIREMENT API 598
43
44
45
46 REMARKS
47 Notes:
48 1) Test duration shall be in accordance with API 6D.
49 2) Valve to be firesafe to API 6FA / API 607.
50 3) Test pressure shall be in accordance with ASME B16.34.
51 4) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
52 5) No repair by welding is allowed on castings/ forgings.
53
54
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification ASME B16.34 / API 6D
4 Tag No. VTD153
5 Piping Class 15S1
6 Class 1500
7
8 VALVE TYPE Globe Valve (Straight Pattern)
9
10
11 END CONNECTION AND RATING 1500 RTJ
12
13
14 MATERIAL
15 Gasket Manufacturer's Standard (Non Asbestos)
16 Body design Bolted Bonnet, Outside Srew and Yoke, Rising Stem
17 Body Material Forged or Cast Stainless Steel ASTM A182 F316
18
19 Trim Design Plug Type Disc, Renewable Seat
20
21 Trim Material TP 316 St Steel Stem, Seat and Disc
22
23 Packing Material Manufacturer's Standard (Non Asbestos)
24
25 VALVE OPERATOR Handwheel
26
27 BOLTING
28 Bonnet & Gland
29 Studs ASTM A320 GR L7 Fluorocarbon coated
30 Nuts ASTM A194 GR 4 Fluorocarbon coated
31
32
33
34 DESIGN CONDITIONS Pressure / Temperature ratings to ASME B16.34
35 Minus 20°C to Plus 120 °C
36
37 TESTS
38 Hydrostatic
39 Body Note 2
40 Seat Note 2
41
42 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
43 INSPECTION AND TESTING REQUIREMENT API 598
44
45
46 REMARKS
47
48 Notes:
49 1) Test duration shall be in accordance with API 6D.
50 2) Test pressure shall be in accordance with ASME B16.34.
51 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
52 4) No repair by welding is allowed on casting / forging.
53
54
55
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 20 - 50
3 Specification ASME B16.34 / API 6D
4 Tag No. VBD153-R
5 Piping Class 15S1
6 Class 1500
7
8 VALVE DESCRIPTION Ball Valve, Stainless Steel, CL 1500, Flanged RTJ. Reduced Bore, Fail
9 Safe, Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti
10 Blowout Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension ASME B16.10 Table 1 Column 19
13 Bore Reduced
14 Bonnet / Adapter Fixing Bolted
15 Operation Lever Operated
16 Construction ball Seat supported
17 End Connections Class 1500 Flanged Ends To ASME B16.5, RTJ
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
21 Body/Bonnet/Adapter ASTM A 182 - F316 or A351 - CF8M
22 Ball ASTM A 182 - F316 or A351 - CF8M
23 Trim/Stem ASTM A 182 - F316 or A706 - 830
24 Seats and Seals PTFE Seat Inserts, PTFE Seals
25 O-Ring VITON
26 Bolting
ASTM A320- L7 STUDS, with A194 - 4 NUTS, Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ASME B16.34
34 Temperature Minus 20°C to Plus 120 °C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 4
41 - Seat Note 4
42 - Air Seat Note 4
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46
47 REMARKS
48 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
49 2) Valve to be firesafe to API 6FA / API 607.
50 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
51 4) Test pressure shall be in accordance with ASME B16.34.
52 5) Valve to have body cavity pressure release
53 6) Ball position indicator shall be provided
54 7) No repair by welding is allowed on castings/ forgings.
55 8) Water proofed gear operater shall be provided.
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification ASME B16.34 / API 6D
4 Tag No. VBD153-F
5 Piping Class 15S1
6 Class 1500
7
8 VALVE DESCRIPTION Ball Valve, Stainless Steel, CL 1500, Flanged RTJ. Full Bore, Fire Safe,
9 Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti Blowout
10 Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension API 6D
13 Bore Full Bore
14 Bonnet / Adapter Fixing Bolted
15 Operation Lever operated
16 Construction ball Trunnion supported
17 End Connections Class 1500 Flanged Ends To ASME B16.5, RTJ
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
21 Body/Bonnet/Adapter ASTM A 182 - F316 or A351 - CF8M
22 Ball ASTM A 182 - F316 or A351 - CF8M
23 Trim/Stem ASTM A 182 - F316 or A706 - 830
24 Seats and Seals PTFE Seat Inserts, PTFE Seals
25 O-Ring VITON
26 Bolting
ASTM A320- L7 STUDS, with A194 - 4 NUTS, Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ASME B16.34
34 Temperature Minus 20°C to Plus 120 °C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 4
41 - Seat Note 4
42 - Air Seat Note 4
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46
47 REMARKS
48 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
49 2) Valve to be firesafe to API 6FA / API 607.
50 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
51 4) Test pressure shall be in accordance with ASME B16.34.
52 5) Valve to have body cavity pressure release
53 6) Ball position indicator shall be provided
54 7) No repair by welding is allowed on castings/ forgings.
55 8) Water proofed gear operater shall be provided.
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 40
3 Specification API 602
4 Tag No. VCD154
5 Piping Class 15S1
6 Class 1500
7
8 VALVE TYPE Check -Piston Type
9
10
11 END CONNECTION AND RATING Flanged to ASME B16.5, RTJ Class 1500
12
13
14 MATERIAL
15 Gasket Manufacturer's Standard (Non Asbestos)
16 Body design Horizontal Flow, spring assisted, bolted bonnet
17 Body Material ASTM A 182 - F316 or A351 - CF8M
18 Trim Design Metal to Metal Seats (Renewable)
19 Trim Material ASTM A 182 - F316
20 Packing Material NA
21 Bolting
ASTM A320- L7 STUDS, with A194 - 4 NUTS, Fluorocarbon Coated
22
23 Spring ASTM B637 UNS N07750
24
25
26 VALVE OPERATOR NA
27
28
29 DESIGN CONDITIONS
30 Pressure Pressure / Temperature ratings to ASME B16.34
31 Temperature
32 - Operating Minus 20°C to PLUS 150° C
33
34
35 TESTS
36 Body Note 2
37 Seat Note 2
38
39
40 INSPECTION AND TESTING REQUIREMENT API 598
41
42 CERTIFICATION DIN 50049 - 3.1B for Body and Bonnet T/Cover
43
44
45 REMARKS
46 Notes:
47 1) Test duration shall be in accordance with API 6D.
48 2) Test pressure shall be in accordance with ASME B16.34.
49 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
50 4) No repair by welding is allowed on casting / forging.
51
52
53
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification API 594
4 Tag No. VCD1584
5 Piping Class 15S1
6 Class 1500
7
8 VALVE TYPE Wafer Check, Dual Plate, (For use in the Horizontal or the
9 vertical with upward flow)
10
11 END CONNECTION AND RATING Suitable for mounting between ASME B16.5 raised
12 RTJ 1500 lb flanges
13
14 MATERIAL
15 Gasket NA
16 Body design Wafer Type - Spring Loaded Dual Plate
17 Body Material
18 Forged ASTM A 182 - F316
19 Cast A 351 CF8M
20
21 Trim Design Metal to Metal seats (Integral)
22
23 Trim Material Stainless steel 316 plates with stellite overlay on
24 body & plate seating areas. Stainless steel
25 hinge and stop pins, B637 UNS N07750 springs
26 Packing Material NA
27
28 VALVE OPERATOR NA
29
30 BOLTING NA
31 Bonnet & Gland
32 Stud
33 Nuts
34
35
36 DESIGN CONDITIONS
37 Pressure Pressure / Temperature ratings to ASME B16.34
38 Temperature Minus 20°C to PLUS 150° C
39 - Operating
40 TESTS
41 Hydrostatic
42 Body Note 2
43 Seat Note 2
44 Pneumatic
45
46 INSPECTION AND TESTING REQUIREMENT API 598
47 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
48
49 REMARKS
50 Notes:
51 1) Test duration shall be in accordance with API 6D.
52 2) Test pressure shall be in accordance with ASME B16.34.
53 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
54 4) No repair by welding is allowed on casting / forging.
55
56
57
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification ASME B16.34
4 Tag No. VDD153
5 Piping Class 15S1
6 Class 1500
7
8 VALVE TYPE
Integral Double Block (ball) & Bleed (needle), Fire safe
9
10
11 END CONNECTION AND RATING Inlet with ASME B16.5 1500# RTJ, outlet 15 mm NPTF
12
13
14 MATERIAL
15 Valves, Body and Trim ASTM A 182 - F316L or A351 - CF8M
16 Gland Packing Peak seat / Grafoil seal
17 Flange ASTM A 182 - F316L or A351 - CF8M
18 Packing Material NA
19 Bolting NA
20
21
22
23
MUTINEER-EXETER DEVELOPMENT
EQUIPMENT : DOUBLE BLOCK & BLEED VALVE PROJECT UNIT MATERIAL CODE SERIAL NO. REV
AP003164 G SP - 1300 0001 0
Data / requisition sheet for
VALVE DATA SHEET - VDD153-F
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification ANSI B16.34
4 Tag No. VDD153-F
5 Piping Class 15S1
6 Class 1500
7
8 VALVE TYPE
Integral Double Block (ball) & Bleed (needle), Fire safe
9
10
11 END CONNECTION AND RATING Inlet and outlet with ASME B16.5 1500# RTJ
12
13
14 MATERIAL
15 Valves, Body and Trim ASTM A 182 - F316L or A351 - CF8M
16 Gland Packing Peak seat / Grafoil seal
17 Flange ASTM A 182 - F316L or A351 - CF8M
18 Packing Material NA
19 Bolting NA
20
21
22
23
24
25
26
27
28 VALVE OPERATOR Lever operated
29
30
31
32
33 DESIGN CONDITIONS
34 Pressure Pressure / Temperature ratings to ASME B16.34
35 Temperature Minus 20°C to PLUS 150° C
36 - Operating
37
38 TESTS
39 Hydrostatic
40 Body Note 3
41 Seat Note 3
42 Pneumatic Note 3
43
44 INSPECTION AND TESTING REQUIREMENT API 598
45
46 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
47
48 REMARKS
49 Notes:
50 1) Test duration shall be in accordance with API 6D.
51 2) Valve to be firesafe to API 6FA / API 607.
52 3) Test pressure shall be in accordance with ASME B16.34.
53 4) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
54 5) No repair in welding is allowed on casting / forging.
55
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification ASME B16.34 / API 6D
4 Tag No. VTD253
5 Piping Class 25S1
6 Class 2500
7
8 VALVE TYPE Globe Valve (Straight Pattern)
9
10
11 END CONNECTION AND RATING 2500 RTJ
12
13
14 MATERIAL
15 Gasket Manufacturer's Standard (Non Asbestos)
16 Body design Bolted Bonnet, Outside Srew and Yoke, Rising Stem
17 Body Material Forged or Cast Stainless Steel ASTM A182 F316
18
19 Trim Design Plug Type Disc, Renewable Seat
20
21 Trim Material TP 316 St Steel Stem, Seat and Disc
22
23 Packing Material Manufacturer's Standard (Non Asbestos)
24
25 VALVE OPERATOR Handwheel
26
27 BOLTING
28 Bonnet & Gland
29 Studs ASTM A320 GR L7 Fluorocarbon coated
30 Nuts ASTM A194 GR 4 Fluorocarbon coated
31
32
33
34 DESIGN CONDITIONS Pressure / Temperature ratings to ASME B16.34
35 Minus 20°C to Plus 120 °C
36
37 TESTS
38 Hydrostatic
39 Body Note 2
40 Seat Note 2
41
42 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
43 INSPECTION AND TESTING REQUIREMENT API 598
44
45
46 REMARKS
47
48 Notes:
49 1) Test duration shall be in accordance with API 6D.
50 2) Test pressure shall be in accordance with ASME B16.34.
51 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
52 4) No repair by welding is allowed on casting / forging.
53
54
55
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 20 - 50
3 Specification ASME B16.34 / API 6D
4 Tag No. VBD253-R
5 Piping Class 25S1
6 Class 2500
7
8 VALVE DESCRIPTION Ball Valve, Stainless Steel, CL 2500, Flanged RTJ. Reduced Bore, Fail
9 Safe, Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti
10 Blowout Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension ASME B16.10 Table 1 Column 19
13 Bore Reduced
14 Bonnet / Adapter Fixing Bolted
15 Operation Lever Operated
16 Construction ball Seat supported
17 End Connections Class 1500 Flanged Ends To ASME B16.5, RTJ
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
21 Body/Bonnet/Adapter ASTM A 182 - F316 or A351 - CF8M
22 Ball ASTM A 182 - F316 or A351 - CF8M
23 Trim/Stem ASTM A 182 - F316 or A706 - 830
24 Seats and Seals PTFE Seat Inserts, PTFE Seals
25 O-Ring VITON
26 Bolting
ASTM A320- L7 STUDS, with A194 - 4 NUTS, Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ASME B16.34
34 Temperature Minus 20°C to Plus 120 °C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 4
41 - Seat Note 4
42 - Air Seat Note 4
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46
47 REMARKS
48 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
49 2) Valve to be firesafe to API 6FA / API 607.
50 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
51 4) Test pressure shall be in accordance with ASME B16.34.
52 5) Valve to have body cavity pressure release
53 6) Ball position indicator shall be provided
54 7) No repair by welding is allowed on castings/ forgings.
55 8) Water proofed gear operater shall be provided.
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification ASME B16.34 / API 6D
4 Tag No. VBD253-F
5 Piping Class 25S1
6 Class 2500
7
8 VALVE DESCRIPTION Ball Valve, Stainless Steel, CL 2500, Flanged RTJ. Full Bore, Fire Safe,
9 Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti Blowout
10 Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension API 6D
13 Bore Full Bore
14 Bonnet / Adapter Fixing Bolted
15 Operation Lever operated
16 Construction ball Trunnion supported
17 End Connections Class 1500 Flanged Ends To ASME B16.5, RTJ
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
21 Body/Bonnet/Adapter ASTM A 182 - F316 or A351 - CF8M
22 Ball ASTM A 182 - F316 or A351 - CF8M
23 Trim/Stem ASTM A 182 - F316 or A706 - 830
24 Seats and Seals PTFE Seat Inserts, PTFE Seals
25 O-Ring VITON
26 Bolting
ASTM A320- L7 STUDS, with A194 - 4 NUTS, Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ASME B16.34
34 Temperature Minus 20°C to Plus 120 °C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 4
41 - Seat Note 4
42 - Air Seat Note 4
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46
47 REMARKS
48 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
49 2) Valve to be firesafe to API 6FA / API 607.
50 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
51 4) Test pressure shall be in accordance with ASME B16.34.
52 5) Valve to have body cavity pressure release
53 6) Ball position indicator shall be provided
54 7) No repair by welding is allowed on castings/ forgings.
55 8) Water proofed gear operater shall be provided.
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 40
3 Specification API 602
4 Tag No. VCD254
5 Piping Class 25S1
6 Class 2500
7
8 VALVE TYPE Check -Piston Type
9
10
11 END CONNECTION AND RATING Flanged to ASME B16.5, RTJ Class 2500
12
13
14 MATERIAL
15 Gasket Manufacturer's Standard (Non Asbestos)
16 Body design Horizontal Flow, spring assisted, bolted bonnet
17 Body Material ASTM A 182 - F316 or A351 - CF8M
18 Trim Design Metal to Metal Seats (Renewable)
19 Trim Material ASTM A 182 - F316
20 Packing Material NA
21 Bolting
ASTM A320- L7 STUDS, with A194 - 4 NUTS, Fluorocarbon Coated
22
23 Spring ASTM B637 UNS N07750
24
25
26 VALVE OPERATOR NA
27
28
29 DESIGN CONDITIONS
30 Pressure Pressure / Temperature ratings to ASME B16.34
31 Temperature
32 - Operating Minus 20°C to PLUS 150° C
33
34
35 TESTS
36 Body Note 2
37 Seat Note 2
38
39
40 INSPECTION AND TESTING REQUIREMENT API 598
41
42 CERTIFICATION DIN 50049 - 3.1B for Body and Bonnet T/Cover
43
44
45 REMARKS
46 Notes:
47 1) Test duration shall be in accordance with API 6D.
48 2) Test pressure shall be in accordance with ASME B16.34.
49 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
50 4) No repair by welding is allowed on casting / forging.
51
52
53
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification API 594
4 Tag No. VCD2584
5 Piping Class 25S1
6 Class 2500
7
8 VALVE TYPE Wafer Check, Dual Plate, (For use in the Horizontal or the
9 vertical with upward flow)
10
11 END CONNECTION AND RATING Suitable for mounting between ASME B16.5 raised
12 RTJ 2500 lb flanges
13
14 MATERIAL
15 Gasket NA
16 Body design Wafer Type - Spring Loaded Dual Plate
17 Body Material
18 Forged ASTM A 182 - F316
19 Cast A 351 CF8M
20
21 Trim Design Metal to Metal seats (Integral)
22
23 Trim Material Stainless steel 316 plates with stellite overlay on
24 body & plate seating areas. Stainless steel
25 hinge and stop pins, B637 UNS N07750 springs
26 Packing Material NA
27
28 VALVE OPERATOR NA
29
30 BOLTING NA
31 Bonnet & Gland
32 Stud
33 Nuts
34
35
36 DESIGN CONDITIONS
37 Pressure Pressure / Temperature ratings to ASME B16.34
38 Temperature Minus 20°C to PLUS 150° C
39 - Operating
40 TESTS
41 Hydrostatic
42 Body Note 2
43 Seat Note 2
44 Pneumatic
45
46 INSPECTION AND TESTING REQUIREMENT API 598
47 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
48
49 REMARKS
50 Notes:
51 1) Test duration shall be in accordance with API 6D.
52 2) Test pressure shall be in accordance with ASME B16.34.
53 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
54 4) No repair by welding is allowed on casting / forging.
55
56
57
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification ASME B16.34
4 Tag No. VDD253
5 Piping Class 25S1
6 Class 2500
7
8 VALVE TYPE
Integral Double Block (ball) & Bleed (needle), Fire safe
9
10
11 END CONNECTION AND RATING Inlet with ASME B16.5 2500# RTJ, outlet 15 mm NPTF
12
13
14 MATERIAL
15 Valves, Body and Trim ASTM A 182 - F316L or A351 - CF8M
16 Gland Packing Peak seat / Grafoil seal
17 Flange ASTM A 182 - F316L or A351 - CF8M
18 Packing Material NA
19 Bolting NA
20
21
22
23
MUTINEER-EXETER DEVELOPMENT
EQUIPMENT : DOUBLE BLOCK & BLEED VALVE PROJECT UNIT MATERIAL CODE SERIAL NO. REV
AP003164 G SP - 1300 0001 0
Data / requisition sheet for
VALVE DATA SHEET - VDD253-F
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification ANSI B16.34
4 Tag No. VDD253-F
5 Piping Class 25S1
6 Class 2500
7
8 VALVE TYPE
Integral Double Block (ball) & Bleed (needle), Fire safe
9
10
11 END CONNECTION AND RATING Inlet and outlet with ASME B16.5 2500# RTJ
12
13
14 MATERIAL
15 Valves, Body and Trim ASTM A 182 - F316L or A351 - CF8M
16 Gland Packing Peak seat / Grafoil seal
17 Flange ASTM A 182 - F316L or A351 - CF8M
18 Packing Material NA
19 Bolting NA
20
21
22
23
24
25
26
27
28 VALVE OPERATOR Lever operated
29
30
31
32
33 DESIGN CONDITIONS
34 Pressure Pressure / Temperature ratings to ASME B16.34
35 Temperature Minus 20°C to PLUS 150° C
36 - Operating
37
38 TESTS
39 Hydrostatic
40 Body Note 3
41 Seat Note 3
42 Pneumatic Note 3
43
44 INSPECTION AND TESTING REQUIREMENT API 598
45
46 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
47
48 REMARKS
49 Notes:
50 1) Test duration shall be in accordance with API 6D.
51 2) Valve to be firesafe to API 6FA / API 607.
52 3) Test pressure shall be in accordance with ASME B16.34.
53 4) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
54 5) No repair in welding is allowed on casting / forging.
55
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 200
3 Specification ASME B16.34 / API 6D
4 Tag No. VTE12
5 Piping Class 1D1
6 Class 150
7
8 VALVE TYPE Globe Valve (Straight Pattern)
9
10
11 END CONNECTION AND RATING 150#RF
12
13
14 MATERIAL
15 Gasket Manufacturer's Standard (Non Asbestos)
16 Body design Bolted Bonnet, Outside Srew and Yoke, Rising Stem
17 Body Material Duplex Stainless Steel ASTM A182 Gr F51 or
18 ASTM A890 Gr 4A
19 Trim Design Plug Type Disc, Renewable Seat
20
21 Trim Material 22 Cr Duplex Stainless Steel Stem, Seat and Disc
22
23 Packing Material Manufacturer's Standard (Non Asbestos)
24
25 VALVE OPERATOR Handwheel
26
27 BOLTING
28 Bonnet & Gland
29 Studs ASTM A193 GR B7 Fluorocarbon coated
30 Nuts ASTM A194 GR 2H Fluorocarbon coated
31
32
33 DESIGN CONDITIONS Pressure / Temperature ratings to ANSI B16.34
34 Minus 20°C to Plus 120 °C
35
36 TESTS
37 Hydrostatic
38 Body Note 2
39 Seat Note 2
40 INSPECTION AND TESTING REQUIREMENT API 598
41
42 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
43
44 REMARKS
45 Notes:
46 1) Test duration shall be in accordance with API 6D.
47 2) Test pressure shall be in accordance with ASME B16.34.
48 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
49 4) No repair by welding is allowed on casting / forging.
50
51
52
53
54
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 250 - 300
3 Specification ASME B16.34 / API 6D
4 Tag No. VTE12-G
5 Piping Class 1D1
6 Class 150
7
8 VALVE TYPE Globe Valve (Straight Pattern)
9
10
11 END CONNECTION AND RATING 150#RF
12
13
14 MATERIAL
15 Gasket Manufacturer's Standard (Non Asbestos)
16 Body design Bolted Bonnet, Outside Srew and Yoke, Rising Stem
17 Body Material Duplex Stainless Steel ASTM A182 Gr F51 or
18 ASTM A890 Gr 4A
19 Trim Design Plug Type Disc, Renewable Seat
20
21 Trim Material 22 Cr Duplex Stainless Steel Stem, Seat and Disc
22
23 Packing Material Manufacturer's Standard (Non Asbestos)
24
25 VALVE OPERATOR Gear Operator
26
27 BOLTING
28 Bonnet & Gland
29 Studs ASTM A193 GR B7 Fluorocarbon coated
30 Nuts ASTM A194 GR 2H Fluorocarbon coated
31
32
33 DESIGN CONDITIONS Pressure / Temperature ratings to ANSI B16.34
34 Minus 20°C to Plus 120 °C
35
36 TESTS
37 Hydrostatic
38 Body Note 2
39 Seat Note 2
40 INSPECTION AND TESTING REQUIREMENT API 598
41
42 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
43
44 REMARKS
45 Notes:
46 1) Test duration shall be in accordance with API 6D.
47 2) Test pressure shall be in accordance with ASME B16.34.
48 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
49 4) No repair by welding is allowed on casting / forging.
50
51
52
53
54
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 20 - 150
3 Specification ASME B16.34 / API 6D
4 Tag No. VBE12-R
5 Piping Class 1D1
6 Class 150
7
8 VALVE DESCRIPTION Ball Valve, 22Cr Duplex SS, CL 150, Flanged RF. Reduced Bore, Fire
9 Safe, Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti
10 Blowout Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension ASME B16.10
13 Bore Reduced
14 Bonnet / Adapter Fixing Bolted
15 Operation Lever Operated
16 Construction ball Seat supported
17 End Connections Class 150 Flanged Ends To ASME B16.5, Raised Face
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
21 Body/Bonnet/Adapter ASTM A182 Gr F51 or A890 Gr 4A
22 Ball ASTM A182 Gr F51or A890 Gr 4A or A276 UN SS31803
23 Trim/Stem ASTM A182 Gr F51or A890 Gr 4A or A276 UN SS31803
24 Seats and Seals PTFE Seat Inserts, PTFE Seals
25 O-Ring Elast-O Lion Minus 40
26 Bolting
ASTM A193 B7 STUDS, with A194 -Gr 2H NUTS Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ANSI B16.34
34 Temperature Minus 20°C to Plus 120 °C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 3
41 - Seat Note 3
42 - Air Seat Note 3
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46
47 REMARKS
48 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
49 2) Valve to be firesafe to API 6FA / API 607.
50 3) Valve to have body cavity pressure release
51 4) Test pressure shall be in accordance with ASME B16.34.
52 5) Ball position indicator shall be provided
53 6) Stem sealant injection shall be provided for valves 6" and larger, all sealant injection points shall incorporate a non return valve.
54 7) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
55 8) No repair by welding is allowed on castings/forgings
56
57
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 200 - 600
3 Specification ASME B16.34 / API 6D
4 Tag No. VBE12-RG
5 Piping Class 1D1
6 Class 150
7
8 VALVE DESCRIPTION Ball Valve, 22Cr Duplex SS, CL 150, Flanged RF. Reduced Bore, Fire
9 Safe, Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti
10 Blowout Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension API 6D
13 Bore Reduced
14 Bonnet / Adapter Fixing Bolted
15 Operation Gear operated
16 Construction ball Trunnion supported
17 End Connections Class 150 Flanged Ends To ASME B16.5, Raised Face
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
21 Body/Bonnet/Adapter ASTM A182 Gr F51 or A890 Gr 4A
22 Ball ASTM A182 Gr F51or A890 Gr 4A or A276 UN SS31803
23 Trim/Stem ASTM A182 Gr F51or A890 Gr 4A or A276 UN SS31803
24 Seats and Seals PTFE Seat Inserts, PTFE Seals
25 O-Ring Elast-O Lion Minus 40
26 Bolting
ASTM A193 B7 STUDS, with A194 - Gr 2H NUTS Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ANSI B16.34
34 Temperature Minus 20°C to Plus 120 °C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 4
41 - Seat Note 4
42 - Air Seat Note 4
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46
47 REMARKS
48 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
49 2) Valve to be firesafe to API 6FA / API 607.
50 3) Valve to have body cavity pressure release
51 4) Test pressure shall be in accordance with ASME B16.34.
52 5) Ball position indicator shall be provided
53 6) Stem sealant injection shall be provided for valve size DN 150 and larger, all sealant injection points shall incorporate a non return valve.
54 7) Valves shall be supplied with water jet proof gear operator.
55 8) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
56 9) No repair by welding is allowed on castings/forgings.
57
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 150
3 Specification ASME B16.34 / API 6D
4 Tag No. VBE12-F
5 Piping Class 1D1
6 Class 150
7
8 VALVE DESCRIPTION Ball Valve, 22Cr Duplex SS, CL 150, Flanged RF. Full Bore, Fire Safe,
9 Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti Blowout
10 Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension ASME B16.10
13 Bore Full Bore
14 Bonnet / Adapter Fixing Bolted
15 Operation Lever Operated
16 Construction ball Seat supported
17 End Connections Class 150 Flanged Ends To ASME B16.5, Raised Face
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
21 Body/Bonnet/Adapter ASTM A182 Gr F51 or A890 Gr 4A
22 Ball ASTM A182 Gr F51or A890 Gr 4A or A276 UN SS31803
23 Trim/Stem ASTM A182 Gr F51or A890 Gr 4A or A276 UN SS31803
24 Seats and Seals PTFE Seat Inserts, PTFE Seals
25 O-Ring Elast-O Lion Minus 40
26 Bolting
ASTM A193 B7 STUDS, with A194 -Gr 2H NUTS Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ANSI B16.34
34 Temperature Minus 20°C to Plus 120 °C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 3
41 - Seat Note 3
42 - Air Seat Note 3
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46
47 REMARKS
48 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
49 2) Valve to be firesafe to API 6FA / API 607.
50 3) Valve to have body cavity pressure release
51 4) Test pressure shall be in accordance with ASME B16.34.
52 5) Ball position indicator shall be provided
53 6) Stem sealant injection shall be provided for valves 6" and larger, all sealant injection points shall incorporate a non return valve.
54 7) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
55 8) No repair by welding is allowed on castings/forgings
56
57
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 200 - 600
3 Specification ASME B16.34 / API 6D
4 Tag No. VBE12-FG
5 Piping Class 1D1
6 Class 150
7
8 VALVE DESCRIPTION Ball Valve, 22Cr Duplex SS, CL 150, Flanged RF. Full Bore, Fire Safe,
9 Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti Blowout
10 Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension API 6D
13 Bore Full Bore
14 Bonnet / Adapter Fixing Bolted
15 Operation Gear operated
16 Construction ball Trunnion supported
17 End Connections Class 150 Flanged Ends To ASME B16.5, Raised Face
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
21 Body/Bonnet/Adapter ASTM A182 Gr F51 or A890 Gr 4A
22 Ball ASTM A182 Gr F51or A890 Gr 4A or A276 UN SS31803
23 Trim/Stem ASTM A182 Gr F51or A890 Gr 4A or A276 UN SS31803
24 Seats and Seals PTFE Seat Inserts, PTFE Seals
25 O-Ring Elast-O Lion Minus 40
26 Bolting
ASTM A193 B7 STUDS, with A194 - Gr 2H NUTS Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ANSI B16.34
34 Temperature Minus 20°C to Plus 120 °C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 4
41 - Seat Note 4
42 - Air Seat Note 4
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46
47 REMARKS
48 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
49 2) Valve to be firesafe to API 6FA / API 607.
50 3) Valve to have body cavity pressure release
51 4) Test pressure shall be in accordance with ASME B16.34.
52 5) Ball position indicator shall be provided
53 6) Stem sealant injection shall be provided for valve size DN 150 and larger, all sealant injection points shall incorporate a non return valve.
54 7) Valves shall be supplied with water jet proof gear operator.
55 8) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
56 9) No repair by welding is allowed on castings/forgings.
57
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 40
3 Specification API 602
4 Tag No. VCE12
5 Piping Class 1D1
6 Class 150
7
8 VALVE TYPE Check -Piston Type
9
10
11 END CONNECTION AND RATING Flanged to ASME B16.5, raised face Class 150
12
13
14 MATERIAL
15 Gasket Manufacturer's Standard (Non Asbestos)
16 Body design Horizontal Flow, spring assisted, bolted bonnet
17 Body Material ASTM A182 Gr F51or A890 Gr 4A or A276 UN SS31803
18 Trim Design Metal to Metal Seats (Renewable)
19 Trim Material 22Cr Duplex SS
20 Packing Material NA
21 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
22
23 Spring ASTM B637 UNS N07750
24
25
26 VALVE OPERATOR NA
27
28
29 DESIGN CONDITIONS
30 Pressure Rating Class 150
31 Temperature
32 - Operating PLUS 0°C to PLUS 150° C
33
34
35 TESTS
36 Body Note 2
37 Seat Note 2
38
39
40 INSPECTION AND TESTING REQUIREMENT API 598
41
42 CERTIFICATION DIN 50049 - 3.1B for Body and Bonnet T/Cover
43
44
45 REMARKS
46 Notes:
47 1) Test duration shall be in accordance with API 6D.
48 2) Test pressure shall be in accordance with ASME B16.34.
49 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
50 4) No repair by welding is allowed on casting / forging.
51
52
53
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 600
3 Specification API 594
4 Tag No. VCE184
5 Piping Class 1D1
6 Class 150
7
8 VALVE TYPE Wafer Check, Dual Plate, (For use in the Horizontal or the
9 vertical with upward flow)
10
11 END CONNECTION AND RATING Suitable for mounting between ASME B16.5 raised
12 face class 150 lb flanges
13
14 MATERIAL
15 Gasket NA
16 Body design Wafer Type - Spring Loaded Dual Plate
17 Body Material
18 Forged ASTM A182 Gr F51or A890 Gr 4A or A276 UN SS31803
19 Cast
20
21 Trim Design Metal to Metal seats (Integral)
22
23 Trim Material 22 Cr Duplex Stainless steel plates with stellite overlay on
24 body & plate seating areas. Duplex Stainless steel
25 hinge and stop pins, B637 UNS N07750 springs
26 Packing Material NA
27
28 VALVE OPERATOR NA
29
30 BOLTING NA
31 Bonnet & Gland
32 Stud
33 Nuts
34
35 DESIGN CONDITIONS
36 Pressure Pressure / Temperature ratings to ANSI B16.34
37 Temperature Minus 20°C to Plus 120 °C
38 - Operating
39 TESTS
40 Hydrostatic
41 Body Note 3
42 Seat Note 3
43 Pneumatic Note 3
44
45 INSPECTION AND TESTING REQUIREMENT API 598
46
47 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
48
49 REMARKS
50 Notes:
51 1) Test duration shall be in accordance with API 6D.
52 2) Valve to be firesafe to API 6FA / API 607.
53 3) Test pressure shall be in accordance with ASME B16.34.
54 4) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
55 5) No repair by welding is allowed on casting / forging.
56
57
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification ASME B16.34
4 Tag No. VDE12
5 Piping Class 1D1
6 Class 150
7
8 VALVE TYPE Integral Double Block (O.S&Y needle) & Bleed (needle),
9 Fire safe
10
11 END CONNECTION AND RATING Inlet with ASME B16.5 150# RF, 2 off 15mm NPTF outlet
12 connections, one located in the centre of the monoflange,
13 the other on the edge of the monoflange, edge connection
14 fitted with a 3000# plug
15
16 MATERIAL
17 Valves, Body and Trim ASTM A182 Gr F51 or A890 Gr 4A w/ 22Cr Duplex SS trim
18 Gland Packing Peek seat / Grafoil seal
19 Flange ASTM A182 Gr F51
20 Packing Material NA
21 Bolting SS 316
22
23
24
25
26 VALVE OPERATOR Handwheel
27
28
29 DESIGN CONDITIONS
30 Pressure Pressure / Temperature ratings to ANSI B16.34
31 Temperature Minus 20°C to Plus 120 °C
32 - Operating
33
34 TESTS
35 Hydrostatic
36 Body Note 3
37 Seat Note 3
38 Pneumatic Note 3
39
40 INSPECTION AND TESTING REQUIREMENT API 598
41
42 CERTIFICATION EN 10204 - 3.1B for all pressure containing parts
43
44 REMARKS
45 Notes:
46 1) Test duration shall be in accordance with API 6D.
47 2) Valve to be firesafe to API 6FA / API 607.
48 3) Test pressure shall be in accordance with ASME B16.34.
49 4) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
50 5) No repair by welding is allowed on castings/ forgings.
51
52
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification ASME B16.34
4 Tag No. VDE12-F
5 Piping Class 1D1
6 Class 150
7
8 VALVE TYPE
Integral Double Block (ball) & Bleed (needle), Fire safe
9
10
11 END CONNECTION AND RATING Inlet and outlet with ASME B16.5 150# RF
12
13
14 MATERIAL
15 Valves, Body and Trim ASTM A182 Gr F51 or A890 Gr 4A w/ 22Cr Duplex SS trim
16 Gland Packing Peek seat / Grafoil seal
17 Flange ASTM A182 Gr F51
18 Packing Material NA
19 Bolting NA
20
21
22
23
24
25
26 VALVE OPERATOR Lever operated
27
28
29
30 DESIGN CONDITIONS
31 Pressure Pressure / Temperature ratings to ANSI B16.34
32 Temperature Minus 20°C to Plus 120 °C
33 - Operating
34
35 TESTS
36 Hydrostatic
37 Body Note 3
38 Seat Note 3
39 Pneumatic Note 3
40
41 INSPECTION AND TESTING REQUIREMENT API 598
42
43 CERTIFICATION EN 10204 - 3.1B for all pressure containing parts
44 REMARKS
45 Notes:
46 1) Test duration shall be in accordance with API 6D.
47 2) Valve to be firesafe to API 6FA / API 607.
48 3) Test pressure shall be in accordance with ASME B16.34.
49 4) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
50 5) No repair in welding is allowed on casting / forging.
51
52
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 150 - 600
3 Specification API 609
4 Tag No. VTOE12-G
5 Piping Class 1D1
6 Class 150
7
8 VALVE TYPE Triple Offset Butterfly Valve, Wafer Lug Type, Fire Safe, Note 6
9 22%Cr Body & Trim, Anti-blowout Stem
10
11 END CONNECTION AND RATING Suitable for mounting between ASME B16.5 raised face
12 CL 150lb flanges
13
14 MATERIAL
15 Body Material ASTM A890 Gr 4A
16 Disk ASTM A890 Gr 4A
17 Shaft / trunnion UNS 31803
18 Gland Plate UNS 31803
19 Body Seat/Seal ASTM A890 Gr 4A
20 Disc Seat/Seal UNS 31803
21 Mounting Plate AISI 316
21 Gaskets Graphite
22 Bearing AISI 316/hard chrome plated
23 Packing Graphite passivated
24 Bolting
UNS 32760
25
26
27 VALVE OPERATOR Gear Operated
28
29
30 DESIGN CONDITIONS
31 Pressure Pressure / Temperature ratings to ANSI B16.34
32 Temperature MINUS 20°C to PLUS 120° C
33 - Operating
34
35 TESTS
36 Hydrostatic
37 Body Note 2
38 Seat Note 2
39 Pneumatic
40
41 INSPECTION AND TESTING REQUIREMENT API 598
42 MARKING API 609 / MSS SP-25
43 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
44
45 REMARKS
46 Notes:
47 1) Test duration shall be in accordance with API 6D and zero leakage for metal seat as stated in API 598.
48 2) Test pressure shall be in accordance with ASME B16.34.
49 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
50 4) No repair by welding is allowed on casting / forging.
51 5) Valve to be firesafe to API 6FA / API 607.
52 6) The threads of the lugs shall be drilled out to allow the studbolts to slide through.
53
54
55
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 200
3 Specification ASME B16.34 / API 6D
4 Tag No. VTE32
5 Piping Class 3D1
6 Class 300
7
8 VALVE TYPE Globe Valve (Straight Pattern)
9
10
11 END CONNECTION AND RATING 300#RF
12
13
14 MATERIAL
15 Gasket Manufacturer's Standard (Non Asbestos)
16 Body design Bolted Bonnet, Outside Srew and Yoke, Rising Stem
17 Body Material Duplex Stainless Steel ASTM A182 Gr F51 or
18 ASTM A890 Gr 4A
19 Trim Design Plug Type Disc, Renewable Seat
20
21 Trim Material 22 Cr Duplex Stainless Steel Stem, Seat and Disc
22
23 Packing Material Manufacturer's Standard (Non Asbestos)
24
25 VALVE OPERATOR Handwheel
26
27 BOLTING
28 Bonnet & Gland
29 Studs ASTM A193 GR B7 Fluorocarbon coated
30 Nuts ASTM A194 GR 2H Fluorocarbon coated
31
32
33
34 DESIGN CONDITIONS Pressure / Temperature ratings to ANSI B16.34
35 Minus 20°C to Plus 120 °C
36
37 TESTS
38 Hydrostatic
39 Body Note 2
40 Seat Note 2
41
42 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
43 INSPECTION AND TESTING REQUIREMENT API 598
44
45
46 REMARKS
47
48 Notes:
49 1) Test duration shall be in accordance with API 6D.
50 2) Test pressure shall be in accordance with ASME B16.34.
51 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
52 4) No repair by welding is allowed on casting / forging.
53
54
55
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 250 - 300
3 Specification ASME B16.34 / API 6D
4 Tag No. VTE32-G
5 Piping Class 3D1
6 Class 300
7
8 VALVE TYPE Globe Valve (Straight Pattern)
9
10
11 END CONNECTION AND RATING 300#RF
12
13
14 MATERIAL
15 Gasket Manufacturer's Standard (Non Asbestos)
16 Body design Bolted Bonnet, Outside Srew and Yoke, Rising Stem
17 Body Material Duplex Stainless Steel ASTM A182 Gr F51 or
18 ASTM A890 Gr 4A
19 Trim Design Plug Type Disc, Renewable Seat
20
21 Trim Material 22 Cr Duplex Stainless Steel Stem, Seat and Disc
22
23 Packing Material Manufacturer's Standard (Non Asbestos)
24
25 VALVE OPERATOR Gear Operator
26
27 BOLTING
28 Bonnet & Gland
29 Studs ASTM A193 GR B7 Fluorocarbon coated
30 Nuts ASTM A194 GR 2H Fluorocarbon coated
31
32
33
34 DESIGN CONDITIONS Pressure / Temperature ratings to ANSI B16.34
35 Minus 20°C to Plus 120 °C
36
37 TESTS
38 Hydrostatic
39 Body Note 2
40 Seat Note 2
41
42 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
43 INSPECTION AND TESTING REQUIREMENT API 598
44
45
46 REMARKS
47
48 Notes:
49 1) Test duration shall be in accordance with API 6D.
50 2) Test pressure shall be in accordance with ASME B16.34.
51 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
52 4) No repair by welding is allowed on casting / forging.
53
54
55
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 20 - 100
3 Specification ASME B16.34 / API 6D
4 Tag No. VBE32-R
5 Piping Class 3D1
6 Class 300
7
8 VALVE DESCRIPTION Ball Valve, 22Cr Duplex SS, CL 300, Flanged RF. Reduced Bore, Fire
9 Safe, Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti
10 Blowout Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension ASME B16.10 Table 1 Column 19
13 Bore Reduced
14 Bonnet / Adapter Fixing Bolted
15 Operation Lever Operated
16 Construction ball Seat supported
17 End Connections Class 300 Flanged Ends To ASME B16.5, Raised Face
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
ASTM A216 WCB with 3mm inconel 625 or duplex S31803 weld overlay
21 Body/Bonnet/Adapter
(Note 8)
22 Ball ASTM A182 Gr F51or A890 Gr 4A or A276 UN SS31803
23 Trim/Stem ASTM A182 Gr F51or A890 Gr 4A or A276 UN SS31803
24 Seats and Seals PTFE Seat Inserts, PTFE Seals
25 O-Ring ELAST-O-LION MINUS 40
26 Bolting
ASTM A193 B7 STUDS, with A194 - 2H NUTS Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ANSI B16.34
34 Temperature Minus 20°C to Plus 120 °C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 4
41 - Seat Note 4
42 - Air Seat Note 4
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46
47
48 REMARKS
49 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
50 2) Valve to be firesafe to API 6FA / API 607.
51 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
52 4) Test pressure shall be in accordance with ASME B16.34.
53 5) Valve to have body cavity pressure release
54 6) Ball position indicator shall be provided
55 7) No repair by welding is allowed on castings/ forgings.
56 8) Weld overlay shall be to the procedures and requirements of API 6A section 6.5.1.2.
57
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 150 - 600
3 Specification ASME B16.34 / API 6D
4 Tag No. VBE32-RG
5 Piping Class 3D1
6 Class 300
7
8 VALVE DESCRIPTION Ball Valve, 22Cr Duplex SS, CL 300, Flanged RF. Reduced Bore, Fire
9 Safe, Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti
10 Blowout Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension API 6D
13 Bore Reduced
14 Bonnet / Adapter Fixing Bolted
15 Operation Gear operated
16 Construction ball Trunnion supported
17 End Connections Class 300 Flanged Ends To ASME B16.5, Raised Face
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
ASTM A216 WCB with 3mm inconel 625 or duplex S31803 weld overlay
21 Body/Bonnet/Adapter
(Note 10)
22 Ball ASTM A182 Gr F51or A890 Gr 4A or A276 UN SS31803
23 Trim/Stem ASTM A182 Gr F51or A890 Gr 4A or A276 UN SS31803
24 Seats and Seals PTFE Seat Inserts, PTFE Seals
25 O-Ring ELAST-O-LION MINUS 40
26 Bolting
ASTM A193 B7 STUDS, with A194 - 2H NUTS Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ANSI B16.34
34 Temperature Minus 20°C to Plus 120 °C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 4
41 - Seat Note 4
42 - Air Seat Note 4
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46
47 REMARKS
48 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
49 2) Valve to be firesafe to API 6FA / API 607.
50 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
51 4) Test pressure shall be in accordance with ASME B16.34.
52 5) Valve to have body cavity pressure release
53 6) Ball position indicator shall be provided
54 7) No repair by welding is allowed on castings/ forgings.
55 8) Stem sealant injection shall be provided for valve size DN 150 and larger, all sealant injection points shall incorporate a non return valve.
56 9) Water proofed gear operater shall be provided.
57 10) Weld overlay shall be to the procedures and requirements of API 6A section 6.5.1.2.
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 100
3 Specification ASME B16.34 / API 6D
4 Tag No. VBE32-F
5 Piping Class 3D1
6 Class 300
7
8 VALVE DESCRIPTION Ball Valve, 22Cr Duplex SS, CL 300, Flanged RF. Full Bore, Fire Safe,
9 Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti Blowout
10 Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension ASME B16.10 Table 1 Column 19
13 Bore Full Bore
14 Bonnet / Adapter Fixing Bolted
15 Operation Lever Operated
16 Construction ball Seat supported
17 End Connections Class 300 Flanged Ends To ASME B16.5, Raised Face
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
ASTM A216 WCB with 3mm inconel 625 or duplex S31803 weld overlay
21 Body/Bonnet/Adapter
(Note 8)
22 Ball ASTM A182 Gr F51or A890 Gr 4A or A276 UN SS31803
23 Trim/Stem ASTM A182 Gr F51or A890 Gr 4A or A276 UN SS31803
24 Seats and Seals PTFE Seat Inserts, PTFE Seals
25 O-Ring ELAST-O-LION MINUS 40
26 Bolting
ASTM A193 B7 STUDS, with A194 - 2H NUTS Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ANSI B16.34
34 Temperature Minus 20°C to Plus 120 °C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 4
41 - Seat Note 4
42 - Air Seat Note 4
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46
47
48 REMARKS
49 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
50 2) Valve to be firesafe to API 6FA / API 607.
51 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
52 4) Test pressure shall be in accordance with ASME B16.34.
53 5) Valve to have body cavity pressure release
54 6) Ball position indicator shall be provided
55 7) No repair by welding is allowed on castings/ forgings.
56 8) Weld overlay shall be to the procedures and requirements of API 6A section 6.5.1.2.
57
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 150 - 600
3 Specification ASME B16.34 / API 6D
4 Tag No. VBE32-FG
5 Piping Class 3D1
6 Class 300
7
8 VALVE DESCRIPTION Ball Valve, 22Cr Duplex SS, CL 300, Flanged RF. Full Bore, Fire Safe,
9 Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti Blowout
10 Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension API 6D
13 Bore Full Bore
14 Bonnet / Adapter Fixing Bolted
15 Operation Gear operated
16 Construction ball Trunnion supported
17 End Connections Class 300 Flanged Ends To ASME B16.5, Raised Face
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
ASTM A216 WCB with 3mm inconel 625 or duplex S31803 weld overlay
21 Body/Bonnet/Adapter
(Note 10)
22 Ball ASTM A182 Gr F51or A890 Gr 4A or A276 UN SS31803
23 Trim/Stem ASTM A182 Gr F51or A890 Gr 4A or A276 UN SS31803
24 Seats and Seals PTFE Seat Inserts, PTFE Seals
25 O-Ring ELAST-O-LION MINUS 40
26 Bolting
ASTM A197 B7 STUDS, with A194 - 2H NUTS Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ANSI B16.34
34 Temperature Minus 20°C to Plus 120 °C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 4
41 - Seat Note 4
42 - Air Seat Note 4
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46
47 REMARKS
48 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
49 2) Valve to be firesafe to API 6FA / API 607.
50 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
51 4) Test pressure shall be in accordance with ASME B16.34.
52 5) Valve to have body cavity pressure release
53 6) Ball position indicator shall be provided
54 7) No repair by welding is allowed on castings/ forgings.
55 8) Stem sealant injection shall be provided for valve size DN 150 and larger, all sealant injection points shall incorporate a non return valve.
56 9) Water proofed gear operater shall be provided.
57 10) Weld overlay shall be to the procedures and requirements of API 6A section 6.5.1.2.
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 40
3 Specification API 602
4 Tag No. VCE32
5 Piping Class 3D1
6 Class 300
7
8 VALVE TYPE Check -Piston Type
9
10
11 END CONNECTION AND RATING Flanged to ASME B16.5, raised face Class 300
12
13
14 MATERIAL
15 Gasket Manufacturer's Standard (Non Asbestos)
16 Body design Horizontal Flow, spring assisted, bolted bonnet
17 Body Material ASTM A182 Gr F51or A890 Gr 4A or A276 UN SS31803
18 Trim Design Metal to Metal Seats (Renewable)
19 Trim Material 22Cr Duplex SS
20 Packing Material NA
21 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
22
23 Spring ASTM B637 UNS N07750
24
25
26 VALVE OPERATOR NA
27
28
29 DESIGN CONDITIONS
30 Pressure Rating Class 300
31 Temperature
32 - Operating PLUS 0°C to PLUS 150° C
33
34
35 TESTS
36 Body Note 2
37 Seat Note 2
38
39
40 INSPECTION AND TESTING REQUIREMENT API 598
41
42 CERTIFICATION DIN 50049 - 3.1B for Body and Bonnet T/Cover
43
44
45 REMARKS
46 Notes:
47 1) Test duration shall be in accordance with API 6D.
48 2) Test pressure shall be in accordance with ASME B16.34.
49 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
50 4) No repair by welding is allowed on casting / forging.
51
52
53
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 50 - 600
3 Specification API 594
4 Tag No. VCE384
5 Piping Class 3D1
6 Class 300
7
8 VALVE TYPE Wafer Check, Dual Plate, (For use in the Horizontal or the
9 vertical with upward flow)
10
11 END CONNECTION AND RATING Suitable for mounting between ASME B16.5 raised
12 face class 300 lb flanges
13
14 MATERIAL
15 Gasket NA
16 Body design Wafer Type - Spring Loaded Dual Plate
17 Body Material
18 Forged A105 with 3mm inconel 625 or duplex S31803 weld overlay (Note 6)
19 Cast
20
21 Trim Design Metal to Metal seats (Integral)
22
23 Trim Material 22 Cr Duplex Stainless steel plates with stellite overlay on
24 body & plate seating areas. Duplex Stainless steel
25 hinge and stop pins, B637 UNS N07750 springs
26 Packing Material NA
27
28 VALVE OPERATOR NA
29
30 BOLTING NA
31 Bonnet & Gland
32 Stud
33 Nuts
34
35 DESIGN CONDITIONS
36 Pressure Pressure / Temperature ratings to ANSI B16.34
37 Temperature Minus 20°C to Plus 120 °C
38 - Operating
39 TESTS
40 Hydrostatic
41 Body Note 3
42 Seat Note 3
43 Pneumatic Note 3
44
45 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
46 INSPECTION AND TESTING REQUIREMENT API 598
47
48 REMARKS
49 Notes:
50 1) Test duration shall be in accordance with API 6D.
51 2) Valve to be firesafe to API 6FA / API 607.
52 3) Test pressure shall be in accordance with ASME B16.34.
53 4) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
54 5) No repair by welding is allowed on castings/ forgings.
55 6) Weld overlay shall be to the procedures and requirements of API 6A section 6.5.1.2.
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification ASME B16.34
4 Tag No. VDE32
5 Piping Class 3D1
6 Class 300
7
8 VALVE TYPE Integral Double Block (O.S&Y needle) & Bleed (needle),
9 Fire safe
10
11 END CONNECTION AND RATING Inlet with ASME B16.5 300# RF, 2 off 15mm NPTF outlet
12 connections, one located in the centre of the monoflange,
13 the other on the edge of the monoflange, edge connection
14 fitted with a 3000# plug
15
16 MATERIAL
17 Valves, Body and Trim ASTM A182 Gr F51 or A890 Gr 4A w/ 22Cr Duplex SS trim
18 Gland Packing Peak seat / Grafoil seal
19 Flange ASTM A182 Gr F51
20 Packing Material NA
21 Bolting SS 316
22
23
24
25
26
27
28 VALVE OPERATOR Handwheel
29
30
31
32
33 DESIGN CONDITIONS
34 Pressure Pressure / Temperature ratings to ANSI B16.34
35 Temperature Minus 20°C to PLUS 120° C
36 - Operating
37
38 TESTS
39 Hydrostatic
40 Body Note 3
41 Seat Note 3
42 Pneumatic Note 3
43
44 INSPECTION AND TESTING REQUIREMENT API 598
45
46 CERTIFICATION EN 10204 - 3.1B for all pressure containing parts
47
48 REMARKS
49 Notes:
50 1) Test duration shall be in accordance with API 6D.
51 2) Valve to be firesafe to API 6FA / API 607.
52 3) Test pressure shall be in accordance with ASME B16.34.
53 4) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
54 5) No repair by welding is allowed on castings/ forgings.
55
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification ASME B16.34
4 Tag No. VDE32-F
5 Piping Class 3D1
6 Class 300
7
8 VALVE TYPE
Integral Double Block (ball) & Bleed (needle), Fire safe
9
10
11 END CONNECTION AND RATING Inlet and outlet with ASME B16.5 300# RF
12
13
14 MATERIAL
15 Valves, Body and Trim ASTM A182 Gr F51 or A890 Gr 4A w/ 22Cr Duplex SS trim
16 Gland Packing Peak seat / Grafoil seal
17 Flange ASTM A182 Gr F51
18 Packing Material NA
19 Bolting NA
20
21
22
23
24
25
26
27
28 VALVE OPERATOR Lever operated
29
30
31
32
33 DESIGN CONDITIONS
34 Pressure Pressure / Temperature ratings to ANSI B16.34
35 Temperature Minus 20°C to Plus 120 °C
36 - Operating
37
38 TESTS
39 Hydrostatic
40 Body Note 3
41 Seat Note 3
42 Pneumatic Note 3
43
44 INSPECTION AND TESTING REQUIREMENT API 598
45
46 CERTIFICATION EN 10204 - 3.1B for all pressure containing parts
47
48 REMARKS
49 Notes:
50 1) Test duration shall be in accordance with API 6D.
51 2) Valve to be firesafe to API 6FA / API 607.
52 3) Test pressure shall be in accordance with ASME B16.34.
53 4) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
54 5) No repair by welding is allowed on castings/ forgings.
55
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 150 - 600
3 Specification API 609
4 Tag No. VTOE32-G
5 Piping Class 3D1
6 Class 300
7
8 VALVE TYPE Triple Offset Butterfly Valve, Wafer Lug Type, Fire Safe, Note 6
9 22%Cr Body & Trim, Anti-blowout Stem
10
11 END CONNECTION AND RATING Suitable for mounting between ASME B16.5 raised face
12 CL 300lb flanges
13
14 MATERIAL
15 Body Material ASTM A890 Gr 4A
16 Disk ASTM A890 Gr 4A
17 Shaft / trunnion UNS 31803
18 Gland Plate UNS 31803
19 Body Seat/Seal ASTM A890 Gr 4A
20 Disc Seat/Seal UNS 31803
21 Mounting Plate AISI 316
21 Gaskets Graphite
22 Bearing AISI 316/hard chrome plated
23 Packing Graphite passivated
24 Bolting
UNS 32760
25
26
27 VALVE OPERATOR Gear Operated
28
29
30 DESIGN CONDITIONS
31 Pressure Pressure / Temperature ratings to ANSI B16.34
32 Temperature MINUS 20°C to PLUS 120° C
33 - Operating
34
35 TESTS
36 Hydrostatic
37 Body Note 2
38 Seat Note 2
39 Pneumatic
40
41 INSPECTION AND TESTING REQUIREMENT API 598
42 MARKING API 609 / MSS SP-25
43 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
44
45 REMARKS
46 Notes:
47 1) Test duration shall be in accordance with API 6D and zero leakage for metal seat as stated in API 598.
48 2) Test pressure shall be in accordance with ASME B16.34.
49 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
50 4) No repair by welding is allowed on casting / forging.
51 5) Valve to be firesafe to API 6FA / API 607.
52 6) The threads of the lugs shall be drilled out to allow the studbolts to slide through.
53
54
55
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 100
3 Specification ASME B16.34 / API 6D
4 Tag No. VTE153
5 Piping Class 15D1
6 Class 1500
7
8 VALVE TYPE Globe Valve (Straight Pattern)
9
10
11 END CONNECTION AND RATING 1500 RTJ
12
13
14 MATERIAL
15 Gasket Manufacturer's Standard (Non Asbestos)
16 Body design Bolted Bonnet, Outside Srew and Yoke, Rising Stem
17 Body Material Duplex Stainless Steel ASTM A182 Gr F51 or
18 ASTM A890 Gr 4A
19 Trim Design Plug Type Disc, Renewable Seat
20
21 Trim Material 22 Cr Duplex Stainless Steel Stem, Seat and Disc
22
23 Packing Material Manufacturer's Standard (Non Asbestos)
24
25 VALVE OPERATOR Handwheel
26
27 BOLTING
28 Bonnet & Gland
29 Studs ASTM A193 GR B7 Fluorocarbon coated
30 Nuts ASTM A194 GR 2H Fluorocarbon coated
31
32
33
34 DESIGN CONDITIONS Pressure / Temperature ratings to ASME B16.34
35 Minus 20°C to Plus 120 °C
36
37 TESTS
38 Hydrostatic
39 Body Note 2
40 Seat Note 2
41
42 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
43 INSPECTION AND TESTING REQUIREMENT API 598
44
45
46 REMARKS
47
48 Notes:
49 1) Test duration shall be in accordance with API 6D.
50 2) Test pressure shall be in accordance with ASME B16.34.
51 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
52 4) No repair by welding is allowed for casting / forging.
53
54
55
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 20 - 50
3 Specification ASME B16.34 / API 6D
4 Tag No. VBE153-R
5 Piping Class 15D1
6 Class 1500
7
8 VALVE DESCRIPTION Ball Valve, 22Cr Duplex SS, CL 1500, Flanged RTJ. Reduced Bore, Fire
9 Safe, Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti
10 Blowout Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension ASME B16.10 Table 1 Column 19
13 Bore Reduced
14 Bonnet / Adapter Fixing Bolted
15 Operation Lever Operated
16 Construction ball Seat supported
17 End Connections Class 300 Flanged Ends To ASME B16.5, Raised Face
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
ASTM A216 WCB with 3mm inconel 625 or duplex S31803 weld overlay
21 Body/Bonnet/Adapter
(Note 8)
22 Ball ASTM A182 Gr F51or A890 Gr 4A or A276 UN SS31803
23 Trim/Stem ASTM A182 Gr F51or A890 Gr 4A or A276 UN SS31803
24 Seats and Seals PEEK
25 O-Ring ELAST-O-LION MINUS 40
26 Bolting
ASTM A193 B7 STUDS, with A194 - 2H NUTS Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ASME B16.34
34 Temperature Minus 20°C to Plus 120 °C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 4
41 - Seat Note 4
42 - Air Seat Note 4
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46
47
48 REMARKS
49 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
50 2) Valve to be firesafe to API 6FA / API 607.
51 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
52 4) Test pressure shall be in accordance with ASME B16.34.
53 5) Valve to have body cavity pressure release
54 6) Ball position indicator shall be provided
55 7) No repair by welding is allowed on castings/ forgings.
56 8) Weld overlay shall be to the procedures and requirements of API 6A section 6.5.1.2.
57
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 80 - 400
3 Specification ASME B16.34 / API 6D
4 Tag No. VBE153-RG
5 Piping Class 15D1
6 Class 1500
7
8 VALVE DESCRIPTION Ball Valve, 22Cr Duplex SS, CL 1500, Flanged RTJ. Reduced Bore, Fire
9 Safe, Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti
10 Blowout Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension API 6D
13 Bore Reduced
14 Bonnet / Adapter Fixing Bolted
15 Operation Gear operated
16 Construction ball Trunnion supported
17 End Connections Class 300 Flanged Ends To ASME B16.5, Raised Face
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
ASTM A216 WCB with 3mm inconel 625 or duplex S31803 weld overlay
21 Body/Bonnet/Adapter
(Note 10)
22 Ball ASTM A182 Gr F51or A890 Gr 4A or A276 UN SS31803
23 Trim/Stem ASTM A182 Gr F51or A890 Gr 4A or A276 UN SS31803
24 Seats and Seals PEEK
25 O-Ring ELAST-O-LION MINUS 40
26 Bolting
ASTM A193 B7 STUDS, with A194 - 2H NUTS Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ASME B16.34
34 Temperature Minus 20°C to Plus 120 °C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 4
41 - Seat Note 4
42 - Air Seat Note 4
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46
47 REMARKS
48 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
49 2) Valve to be firesafe to API 6FA / API 607.
50 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
51 4) Test pressure shall be in accordance with ASME B16.34.
52 5) Valve to have body cavity pressure release
53 6) Ball position indicator shall be provided
54 7) No repair by welding is allowed on castings/ forgings.
55 8) Stem sealant injection shall be provided for valve size DN 150 and larger, all sealant injection points shall incorporate a non return valve.
56 9) Water proofed gear operater shall be provided.
57 10) Weld overlay shall be to the procedures and requirements of API 6A section 6.5.1.2.
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 80
3 Specification ASME B16.34 / API 6D
4 Tag No. VBE153-F
5 Piping Class 15D1
6 Class 1500
7
8 VALVE DESCRIPTION Ball Valve, 22Cr Duplex SS, CL 1500, Flanged RTJ. Full Bore, Fire Safe,
9 Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti Blowout
10 Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension ASME B16.10 Table 1 Column 19
13 Bore Full Bore
14 Bonnet / Adapter Fixing Bolted
15 Operation Lever Operated
16 Construction ball Seat supported
17 End Connections Class 300 Flanged Ends To ASME B16.5, Raised Face
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
ASTM A216 WCB with 3mm inconel 625 or duplex S31803 weld overlay
21 Body/Bonnet/Adapter
(Note 8)
22 Ball ASTM A182 Gr F51or A890 Gr 4A or A276 UN SS31803
23 Trim/Stem ASTM A182 Gr F51or A890 Gr 4A or A276 UN SS31803
24 Seats and Seals PEEK
25 O-Ring ELAST-O-LION MINUS 40
26 Bolting
ASTM A193 B7 STUDS, with A194 - 2H NUTS Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ASME B16.34
34 Temperature Minus 20°C to Plus 120 °C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 4
41 - Seat Note 4
42 - Air Seat Note 4
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46
47
48 REMARKS
49 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
50 2) Valve to be firesafe to API 6FA / API 607.
51 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
52 4) Test pressure shall be in accordance with ASME B16.34.
53 5) Valve to have body cavity pressure release
54 6) Ball position indicator shall be provided
55 7) No repair by welding is allowed on castings/ forgings.
56 8) Weld overlay shall be to the procedures and requirements of API 6A section 6.5.1.2.
57
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 100 - 400
3 Specification ASME B16.34 / API 6D
4 Tag No. VBE153-FG
5 Piping Class 15D1
6 Class 1500
7
8 VALVE DESCRIPTION Ball Valve, 22Cr Duplex SS, CL 1500, Flanged RTJ. Full Bore, Fire Safe,
9 Fitted with Graphite Fire Seals, Side Entry, Bolted Body Anti Blowout
10 Stem, Anti-Static Device.
11 GENERAL
12 Face to Face Dimension API 6D
13 Bore Full Bore
14 Bonnet / Adapter Fixing Bolted
15 Operation Gear operated
16 Construction ball Trunnion supported
17 End Connections Class 1500 Flanged Ends To ASME B16.5, RTJ
18 Flange Finish Gasket Contact Surface Finish 3.2 - 6.3 Micrometres Ra In accordance
19 with ANSI B46.1
20 MATERIAL
ASTM A216 WCB with 3mm inconel 625 or duplex S31803 weld overlay
21 Body/Bonnet/Adapter
(Note 10)
22 Ball ASTM A182 Gr F51or A890 Gr 4A or A276 UN SS31803
23 Trim/Stem ASTM A182 Gr F51or A890 Gr 4A or A276 UN SS31803
24 Seats and Seals PEEK
25 O-Ring ELAST-O-LION MINUS 40
26 Bolting
ASTM A197 B7 STUDS, with A194 - 2H NUTS Fluorocarbon Coated
27
28 Bonnet Gasket 316 St. St. Spiral Wound with Graphite Filler and 316 St. St Inner &
29 Outer Rings
30 Spring ASTM B637 UNS N07750
31
32 DESIGN
33 Pressure Pressure / Temperature ratings to ASME B16.34
34 Temperature Minus 20°C to Plus 120 °C
35 - Operating
36 - Blowdown -
37
38 TESTS
39 Hydrostatic
40 - Body Note 4
41 - Seat Note 4
42 - Air Seat Note 4
43
44 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
45 INSPECTION In accordance with Purchase Order
46
47 REMARKS
48 1) Test duration shall be in accordance with API 6D and zero leakage for resilient seat as stated in API 598.
49 2) Valve to be firesafe to API 6FA / API 607.
50 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
51 4) Test pressure shall be in accordance with ASME B16.34.
52 5) Valve to have body cavity pressure release
53 6) Ball position indicator shall be provided
54 7) No repair by welding is allowed on castings/ forgings.
55 8) Stem sealant injection points with non-return valves shall be provided for valve size DN 150 and larger.
56 9) Water proofed gear operater shall be provided.
57 10) Weld overlay shall be to the procedures and requirements of API 6A section 6.5.1.2.
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 40
3 Specification API 602
4 Tag No. VCE153
5 Piping Class 15D1
6 Class 1500
7
8 VALVE TYPE Check -Piston Type
9
10
11 END CONNECTION AND RATING Flanged to ASME B16.5, RTJ Class 1500
12
13
14 MATERIAL
15 Gasket Manufacturer's Standard (Non Asbestos)
16 Body design Horizontal Flow, spring assisted, bolted bonnet
17 Body Material ASTM A182 Gr F51or A890 Gr 4A or A276 UN SS31803
18 Trim Design Metal to Metal Seats (Renewable)
19 Trim Material 22Cr Duplex SS
20 Packing Material NA
21 Bolting
ASTM A193 - B7 STUDS, with A194 - 2H NUTS, Fluorocarbon Coated
22
23 Spring ASTM B637 UNS N07750
24
25
26 VALVE OPERATOR NA
27
28
29 DESIGN CONDITIONS
30 Pressure Rating Class 1500
31 Temperature
32 - Operating PLUS 0°C to PLUS 150° C
33
34
35 TESTS
36 Body Note 2
37 Seat Note 2
38
39
40 INSPECTION AND TESTING REQUIREMENT API 598
41
42 CERTIFICATION DIN 50049 - 3.1B for Body and Bonnet T/Cover
43
44
45 REMARKS
46 Notes:
47 1) Test duration shall be in accordance with API 6D.
48 2) Test pressure shall be in accordance with ASME B16.34.
49 3) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
50 4) No repair by welding is allowed for casting / forging.
51
52
53
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 400
3 Specification API 594
4 Tag No. VCE1584
5 Piping Class 15D1
6 Class 1500
7
8 VALVE TYPE Wafer Check, Dual Plate, (For use in the Horizontal or the
9 vertical with upward flow)
10
11 END CONNECTION AND RATING Suitable for mounting between ASME B16.5 raised
12 face, RTJ, class 1500 lb flanges
13
14 MATERIAL
15 Gasket NA
16 Body design Wafer Type - Spring Loaded Dual Plate
17 Body Material
18 Forged A105 with 3mm inconel 625 or duplex S31803 weld overlay (Note 6)
19 Cast
20
21 Trim Design Metal to Metal seats (Integral)
22
23 Trim Material 22 Cr Duplex Stainless steel plates with stellite overlay on
24 body & plate seating areas. Duplex Stainless steel
25 hinge and stop pins, B637 UNS N07750 springs
26 Packing Material NA
27
28 VALVE OPERATOR NA
29
30 BOLTING NA
31 Bonnet & Gland
32 Stud
33 Nuts
34
35 DESIGN CONDITIONS
36 Pressure Pressure / Temperature ratings to ASME B16.34
37 Temperature Minus 20°C to Plus 120 °C
38 - Operating
39 TESTS
40 Hydrostatic
41 Body Note 3
42 Seat Note 3
43 Pneumatic Note 3
44
45 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
46 INSPECTION AND TESTING REQUIREMENT API 598
47
48 REMARKS
49 Notes:
50 1) Test duration shall be in accordance with API 6D.
51 2) Valve to be firesafe to API 6FA / API 607.
52 3) Test pressure shall be in accordance with ASME B16.34.
53 4) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
54 5) No repair by welding is allowed on castings/ forgings.
55 6) Weld overlay shall be to the procedures and requirements of API 6A section 6.5.1.2.
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification ASME B16.34
4 Tag No. VDE153
5 Piping Class 15D1
6 Class 1500
7
8 VALVE TYPE
Integral Double Block (ball) & Bleed (needle), Fire safe
9
10
11 END CONNECTION AND RATING Inlet with ASME B16.5 1500# RTJ, outlet 15 mm NPTF
12
13
14 MATERIAL
15 Valves, Body and Trim ASTM A182 Gr F51 or A890 Gr 4A w/ 22Cr Duplex SS trim
16 Gland Packing Peak seat / Grafoil seal
17 Flange ASTM A182 Gr F51
18 Packing Material NA
19 Bolting NA
20
21
22
23
24
25
26
27
28 VALVE OPERATOR Lever operated
29
30
31
32
33 DESIGN CONDITIONS
34 Pressure Pressure / Temperature ratings to ASME B16.34
35 Temperature Minus 20°C to Plus 120 °C
36 - Operating
37
38 TESTS
39 Hydrostatic
40 Body Note 3
41 Seat Note 3
42
43 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
44 INSPECTION AND TESTING REQUIREMENT API 598
45
46
47
48 REMARKS
49 Notes:
50 1) Test duration shall be in accordance with API 6D.
51 2) Valve to be firesafe to API 6FA / API 607.
52 3) Test pressure shall be in accordance with ASME B16.34.
53 4) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
54 5) No repair by welding is allowed on castings/ forgings.
55
56
MUTINEER-EXETER DEVELOPMENT
1 REQUIRED OFFERED
2 Size range DN 15 - 50
3 Specification ASME B16.34
4 Tag No. VDE153-F
5 Piping Class 15D1
6 Class 1500
7
8 VALVE TYPE
Integral Double Block (ball) & Bleed (needle), Fire safe
9
10
11 END CONNECTION AND RATING Inlet and outlet with ASME B16.5 1500# RTJ
12
13
14 MATERIAL
15 Valves, Body and Trim ASTM A182 Gr F51 or A890 Gr 4A w/ 22Cr Duplex SS trim
16 Gland Packing Peak seat / Grafoil seal
17 Flange ASTM A182 Gr F51
18 Packing Material NA
19 Bolting NA
20
21
22
23
24
25
26
27
28 VALVE OPERATOR Lever operated
29
30
31
32
33 DESIGN CONDITIONS
34 Pressure Pressure / Temperature ratings to ASME B16.34
35 Temperature Minus 20°C to Plus 120 °C
36 - Operating
37
38 TESTS
39 Hydrostatic
40 Body Note 3
41 Seat Note 3
42
43 CERTIFICATION EN 10204 - 3.1B for Body and Bonnet T/Cover
44 INSPECTION AND TESTING REQUIREMENT API 598
45
46
47
48 REMARKS
49 Notes:
50 1) Test duration shall be in accordance with API 6D.
51 2) Valve to be firesafe to API 6FA / API 607.
52 3) Test pressure shall be in accordance with ASME B16.34.
53 4) Minimum thickness of valve bodies shall be in accordance with ASME B16.34.
54 5) No repair by welding is allowed on castings/ forgings.
55
56
MUTINEER-EXETER DEVELOPMENT