Professional Documents
Culture Documents
2016
DIN 316
D
ICS 21.060.10 Supersedes
DIN 316:1998-07
Fasteners –
Wing screws –
Rounded wings,
English translation of DIN 316:2016-12
Mechanische Verbindungselemente –
Flügelschrauben –
Runde Flügelform,
Englische Übersetzung von DIN 316:2016-12
Fixations –
Vis à oreilles –
Oreilles arrondies,
Traduction anglaise de DIN 316:2016-12
Translation by DIN-Sprachendienst.
In case of doubt, the German-language original shall be considered authoritative.
© No part of this translation may be reproduced without prior permission of English price group 6
DIN Deutsches Institut für Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,
has the exclusive right of sale for German Standards (DIN-Normen).
www.din.de
www.beuth.de
!%c@l"
03.17 2642973
Copyright by DIN. Reproduced by ANSI with permission of and under license from DIN.
Licensed to AMITH KRISHNA. Downloaded 3/15/2018 5:25 AM. Not for additional sale or distribution.
DIN 316:2016-12
Contents
Page
Foreword ................................................................................................................................................................................... 3
1 Scope ............................................................................................................................................................................ 4
2 Normative references ............................................................................................................................................ 4
3 Dimensions ................................................................................................................................................................ 4
4 Technical delivery conditions ............................................................................................................................. 6
5 Designation ................................................................................................................................................................ 6
Bibliography ............................................................................................................................................................................. 7
2
Copyright by DIN. Reproduced by ANSI with permission of and under license from DIN.
Licensed to AMITH KRISHNA. Downloaded 3/15/2018 5:25 AM. Not for additional sale or distribution.
DIN 316:2016-12
Foreword
This standard has been prepared by Working Committee NA 067-00-08 AA Verbindungselemente mit
Sonderformen und aus Kunststoff of DIN-Normenausschuss Mechanische Verbindungselemente (DIN Standards
Committee Fasteners).
The DIN 4000-160-4 tabular layout of product properties applies to wing screws covered in this standard.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. DIN [and/or DKE] shall not be held responsible for identifying any or all such patent rights.
Amendments
c) thread ends according to DIN EN ISO 4753 have been specified in Figure 1;
d) in Table 2, thread tolerances have been changed from 6g to 8g according to DIN EN ISO 4759-1 and
reference has been made to DIN ISO 965-1;
e) the content of Annex A (tabular layout of article characteristics) has been transferred to the Foreword
and updated;
Previous editions
3
Copyright by DIN. Reproduced by ANSI with permission of and under license from DIN.
Licensed to AMITH KRISHNA. Downloaded 3/15/2018 5:25 AM. Not for additional sale or distribution.
DIN 316:2016-12
1 Scope
This standard specifies requirements for M4 to M24 wing screws with rounded wings, of product grade C
and made of malleable cast iron, steel, austenitic steel or copper-zinc alloy.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
DIN EN ISO 225, Fasteners — Bolts, screws, studs and nuts — Symbols and descriptions of dimensions
DIN EN ISO 4753, Fasteners — Ends of parts with external ISO metric thread
DIN EN ISO 4759-1, Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C
DIN ISO 965-1, ISO general purpose metric screw threads — Tolerances — Part 1: Principles and basic data
DIN ISO 8992, Fasteners — General requirements for bolts, screws, studs and nuts
3 Dimensions
See Figure 1 and Table 1.
a Thread end according to DIN EN ISO 4753 Type RL or end chamfered (CH) at the manufacturer’s discretion
Figure 1 — Dimensions
4
Copyright by DIN. Reproduced by ANSI with permission of and under license from DIN.
Licensed to AMITH KRISHNA. Downloaded 3/15/2018 5:25 AM. Not for additional sale or distribution.
DIN 316:2016-12
Table 1 — Dimensions
Dimensions in millimetres
Thread, d1 M4 M5 M6 M8 M10 M12 M16 M20 M24
Pa 0,7 0,8 1 1,25 1,5 1,75 2 2,5 3
a max. 2,1 2,4 3 4 4,5 5,3 6 7,5 9
max. 8 11 13 16 20 23 29 35 44
d2
min. 6 8 10 13 17 20 26 32 41
max. 7 9 11 12,5 16,5 19,5 23 29 37,5
d3
min. 5,5 7,5 9 10,5 14,5 17,5 21 27 35
max. 20 26 33 39 51 65 73 90 110
e
min. 18 24 30 36 48 62 70 86 106
max. 1,9 2,3 2,3 2,8 4,4 4,9 6,4 6,9 9,4
g1
min. 1,1 1,5 1,5 2 3,6 4,1 5,6 6,1 8,6
max. 2,3 2,8 3,3 4,4 5,4 6,4 7,5 8 10,5
g2
min. 1,7 2,3 2,7 3,6 4,6 5,6 6,5 7 9,5
max. 10,5 13 17 20 25 33,5 37,5 46,5 56,5
h
min. 8,5 11 15 18 23 31 35 44 53,5
max. 4,6 6,5 8 10 12 14 17 21 25
m
min. 3,2 4 5 6,5 8 10 13 16 20
r1 ≈ 3 4 5 6 8 10 11 14 18
r2 ≈ Rounded 1 1 1,2 1,6 2,5
r3 ≈ 0,5 1 1 1 1,2 1,2 1,6 2 2,5
r4 ≈ 2 2,5 3 3 5 6 7 8 9
lb
Nom.
size min. max.
6 5,40 6,60
8 7,25 8,75
10 9,25 10,75
12 11,10 12,90
(14) 13,10 14,90 Range of
16 15,10 16,90
(18) 17,10 18,90
20 18,95 21,05 commercially available
25 23,95 26,05
30 28,95 31,05
35 33,75 36,25 lengths
40 38,75 41,25
50 48,75 51,25
60 58,50 61,50
a P = Thread pitch
b Bracketed sizes should be avoided if possible.
5
Copyright by DIN. Reproduced by ANSI with permission of and under license from DIN.
Licensed to AMITH KRISHNA. Downloaded 3/15/2018 5:25 AM. Not for additional sale or distribution.
DIN 316:2016-12
General
Standard DIN ISO 8992
requirements
Tolerance
8ga
Thread class
Standard DIN ISO 965-1
Limit Product
C
deviations, grade
geometrical
tolerances Standard DIN EN ISO 4759-1
As processed.
Surface finish — Coating Bearing face unmachined.
DIN EN ISO 4042 applies with regard to electroplating.
Acceptance inspection DIN EN ISO 3269
a Depending on the surface finish, another tolerance position prior to the application of the coating is necessary;
see DIN EN ISO 4042, for example.
Wing screws according to this standard may be made from two pieces, with a combination of malleable cast
iron (GT) and steel (St) being permissible. They shall be joined in such a manner that their perfomance is
equal to that of one-piece screws.
5 Designation
Designation of an M6 wing screw with rounded wings, made of malleable cast iron (GT), with a nominal
length, l, of 20 mm:
6
Copyright by DIN. Reproduced by ANSI with permission of and under license from DIN.
Licensed to AMITH KRISHNA. Downloaded 3/15/2018 5:25 AM. Not for additional sale or distribution.
DIN 316:2016-12
Bibliography
[2] DIN 4000-160, Tabular layout of product properties — Part 160: Fasteners with external thread
7
Copyright by DIN. Reproduced by ANSI with permission of and under license from DIN.
Licensed to AMITH KRISHNA. Downloaded 3/15/2018 5:25 AM. Not for additional sale or distribution.