Professional Documents
Culture Documents
A-746871-03-En - Pipe Class C225 DIN EN
A-746871-03-En - Pipe Class C225 DIN EN
Rating
Technical Specification DIN EN PN6
T-02-01-EN
CONTENT
Rating
Technical Specification DIN EN PN6
T-02-01-EN
1. DESIGN NOTES
3
0 200 40 32 392
2.5 2 2 29 29
572
2 300 30 22
1.5
[barg]
[psig]
1.5
20 806
430 7
1 0.5
10
0.5
0 0
0 100 200 300 400 500 32 232 432 632 832
[°C] [°F]
2. TYPICAL USE
• Vapour Ducts
3. REFERENCES
The following valve classes can be used together with this pipe class:
32VD (only for connected piping)
Comparable pipe classes according to ASME standard:
C669
Rating
Technical Specification DIN EN PN6
T-02-01-EN
4. TUBES
DN 15 20 25 32 40 50 65 80 100 125 150 200 250 300 350 400 450 500
øD 21.3 26.9 33.7 42.4 48.3 60.3 76.1 88.9 114.3 139.7 168.3 219.1 273.0 323.9 355.6 406.4 457.0 508.0
S 2.0 2.0 2.0 2.0 2.0 2.6 2.6 2.6 2.6 2.6 2.6 3.2 3.2 3.2 4.0 4.0 5.0 5.0
5. FLANGES
DIN EN 1092-1
Slip-on flange type 01 / A DN 15 - 900
PN 6
DIN EN 1092-1
DN 15 - 40
PN 10-40
Slip-on flange type 01 / A
DIN EN 1092-1
DN 50 - 150 1.4404 DIN EN 10028-7
only to be used if connected equipment nozzle, PN 10-16
piping or instrumentation is defined with higher DIN EN 1092-1
pressure rating PN10 or PN16 DN 200 - 900
PN 10
(to be checked by piping engineering)
DIN EN 1092-1
DN 200 - 900
PN 16
DIN EN 1092-1
Blind flange type 05 / A DN 15 - 900
PN 6
DIN EN 1092-1
DN 15 - 40
PN 10-40
Blind flange type 05 / A
DIN EN 1092-1
DN 50 - 150 1.4404 DIN EN 10028-7
only to be used if connected equipment nozzle, PN 10-16
piping or instrumentation is defined with higher DIN EN 1092-1
pressure rating PN10 or PN16 DN 200 - 900
PN 10
(to be checked by piping engineering)
DIN EN 1092-1
DN 200 - 900
PN 16
Rating
Technical Specification DIN EN PN6
T-02-01-EN
6. BUCKLING
to be
H 40 40 40 40
calculated
b 10 10 12 12
7. FITTINGS
Rating
Technical Specification DIN EN PN6
T-02-01-EN
8. GASKETS
DIN EN 1514-1
Flat gasket form IBC DN 15 - 900
PN 6
DIN EN 1514-1
DN 15 - 80
PN 10-40
Flat gasket form IBC
DIN EN 1514-1
DN 100 - 200 Graphite with double tanged sheet 1.4401
only to be used if connected equipment nozzle, PN 10-16
piping or instrumentation is defined with higher DIN EN 1514-1
pressure rating PN10 or PN16 DN 250 - 900
PN 10
(to be checked by piping engineering)
DIN EN 1514-1
DN 250 - 900
PN 16
9. BOLTING MATERIAL
8.8 galvanized,
Hexagon screw up to 300°C DIN EN ISO 898-1 DIN EN ISO 4014 / 4017
yellow passivated
Screw with reduced shank above 300°C A2-70 DIN EN ISO 3506-1 DIN 2510 form L
8 galvanized,
Hexagon nut up to 300°C DIN EN ISO 898-2 DIN EN ISO 4032
yellow passivated
Hexagon nut above 300°C A2-70 DIN EN ISO 3506-2 DIN 2510 form NF
Stud bolt
8.8 galvanized,
(for clamped items and at plate heat exchanger up to 300°C DIN EN ISO 898-1 DIN 976-1
yellow passivated
connections only)