Professional Documents
Culture Documents
Electrical Equipment: Wipers - Washers
Electrical Equipment: Wipers - Washers
WIPERS – WASHERS
85A
UCH
Vdiag No.: 08, 09, 0E, 0F
V4 Edition Anglaise
"The repair procedures given by the manufacturer in this document are based on the All rights reserved by Renault s.a.s.
technical specifications current when it was prepared.
Copying or translating, in part or in full, of this document or use of the service part
The procedures may be modified as a result of changes introduced by the reference numbering system is forbidden without the prior written authority of
manufacturer in the production of the various component units and accessories from Renault s.a.s.
which his vehicles are constructed."
This document presents the fault finding method applicable to all computers with the following specifications:
Documentation type
Fault finding procedures (this manual):
– Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
– Visu-Schéma.
Diagnostic tool
Multimeter
Elé. 1622 Bornier
If the information obtained by the diagnostic tool requires the electrical continuity to be checked, connect
bornier Elé. 1622 or universal bornier Elé. 1681.
WARNING:
– All checks using bornier Elé. 1622 or Elé. 1681 must be carried out with the battery disconnected.
– The bornier is only designed to be used with a multimeter. Never supply the test points with 12 V.
UCH_V08_PRELI/UCH_V09_PRELI/UCH_V0E_PRELI/UCH_V0F_PRELI
MR-426-B90-85A000$010.mif
V4
85A-2
UCH
WIPERS – WASHERS
85A
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Introduction
3. SAFETY INSTRUCTIONS
Safety rules must be observed during any work on a component to prevent any damage or injury:
– make sure that the battery is properly charged to avoid damaging the computers with a low charge,
– use the appropriate tools.
MR-426-B90-85A000$010.mif
V4
85A-3
UCH
WIPERS – WASHERS
85A
Vdiag No.: 08, 09, 0E,
0F
Fault finding – List and location of components
6 7
1
4 7
2
5
7
3
4 2
MR-426-B90-85A000$020.mif
V4
85A-4
UCH
WIPERS – WASHERS
85A
Vdiag No.: 08, 09, 0E,
0F
Fault finding – List and location of components
3 7 5
4 2
MR-426-B90-85A000$020.mif
V4
85A-5
UCH
WIPERS – WASHERS
85A
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Role of components
Combined wiper-washer:
The role of the combined wiper-washer control is to control the various washing and wiping functions.
UCH:
The UCH is used to manage all wiper functions (activation, wiper speed, etc).
MR-426-B90-85A000$030.mif
V4
85A-6
UCH
WIPERS – WASHERS
85A
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Operating diagram
645 UCH
MAM
14A
14B M
14D
212
1016
16A 677
AP7
MF
MR-426-B90-85A000$040.mif
V4
85A-7
UCH
WIPERS – WASHERS
85A
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Operating diagram
MAM
36G
F27 (20 A) 145
211
1016 677
24A
AP9
MG
Diagram of the heated rear screen without heated rear screen relay:
MAM
F19
1016 MF or MG
15A 247
MR-426-B90-85A000$040.mif
V4
85A-8
UCH
WIPERS – WASHERS
85A
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Operating diagram
Diagram of the heated rear screen with heated rear screen relay:
MAM
15B
1456
645
235
15LP
F19 15LP
200
1016 BP15
15LP
MF
MR-426-B90-85A000$040.mif
V4
85A-9
UCH
WIPERS – WASHERS
85A
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Function
Windscreen washing/wiping
The UCH receives the wiper speed, windscreen wiper park position and windscreen washer signals.
This ensures the following functions:
– intermittent wiper speed,
– extended wiper time after washing,
– return to park position.
In the park position, the switch is closed to earth, and the UCH receives logical signal 0.
Detection of the park position should be made during transition and not level, that is, if the wiper stalk is moved from
the intermittent position to the park position while the wiper blade is in the park position and the wiper motor is
running, it will not be stopped until the next reading of the park position. This condition is necessary in order to obtain
an exact park position.
Intermittent
The intermittent wiper speed function is only active if the + after ignition is present and if the switch is in the
intermittent position.
The time delay between two wipes is 5 seconds, and this cannot be modified by the diagnostic tool.
When the windscreen intermittent speed function is activated, the windscreen intermitted speed relay is held by the
UCH until the park position is detected. When the intermittent speed time delay has elapsed, the relay is held again
and the cycle begins again.
The UCH does not manage the windscreen washer pump command, it only deals with the windscreen washer
command input to provide screen wiping and the extended wiper time after washing.
After the washer pump is activated, the first wiping is performed after a time delay of 750 ms.
When the washing control is pressed briefly, the windscreen wiper performs 1 wiping cycle.
When the washing control is pressed for longer, the UCH activates the windscreen wiper throughout the washing
phase. At the end of the washing phase, the UCH counts the park position status changes in order to stop the
extended wiping phase.
MR-426-B90-85A000$050.mif
V4
85A-10
UCH
WIPERS – WASHERS
85A
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Function
The UCH controls a diode relay which is external to the UCH, by transmitting a + 12 V signal.
The drop in the voltage between the UCH supply voltage and this output should not exceed 2 V.
The UCH receives the intermittent wiper speed, rear wiper park and rear screen washer signals.
This ensures the following functions:
– intermittent wiper speed,
– extended wiper time after washing,
– return to park position.
In the park position, the switch is closed to earth, and the UCH receives logical signal 0.
Detection of the park position should be made during transition and not level, that is, if the wiper stalk is moved from
the intermittent position to the park position while the wiper blade is in the park position and the wiper motor is
running, it will not be stopped until the next reading of the park position. This condition is necessary in order to obtain
an exact park position.
Intermittent
The intermittent wiper speed function is only active if the + after ignition is present and if the switch is in the
intermittent position.
The time delay between two wipes is 5 seconds, and this cannot be modified by the diagnostic tool.
When the rear intermittent speed function is activated, the rear intermittent speed relay is held by the UCH until the
park position is detected. When the intermittent speed time delay has elapsed, the relay is held again and the cycle
begins again.
The UCH does not manage the rear washer pump command.
It only deals with the rear screen washer command input to provide wiping and extended wiping after washing.
This function is only active if + after ignition feed is present.
After the washer pump is activated, the first wiping is performed after a time delay of 750 ms.
MR-426-B90-85A000$050.mif
V4
85A-11
UCH
WIPERS – WASHERS
85A
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Function
This output controls a diode relay which is external to the UCH, delivering the power to supply the heated rear
screen.
The de-icing time delay is activated by pressing the heated rear screen button located on the central console front
panel.
The minimum time delay between two presses of the button so that the command is taken into account, should not
be less than 200 ms.
MR-426-B90-85A000$050.mif
V4
85A-12
UCH
WIPERS – WASHERS
85A
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Configuration
Equipment required:
Configuration
Name of configuration Option Configuration
reading
MR-426-B90-85A000$060.mif
V4
85A-13
UCH
WIPERS – WASHERS
85A
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Fault summary table
MR-426-B90-85A000$070.mif
V4
85A-14
UCH
WIPERS – WASHERS
85A
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Fault Interpretation
The fault is declared present following operation of the rear screen wiper.
Special notes: random operation of screen wiping in intermittent speed position (time
delay not respected).
NOTES
Special note:
Use Wiring Diagrams Technical Note for Logan / Sandero.
Check that the rear screen park position status ET097 Rear screen park position is ACTIVE each time the wiper
blade arrives at the park position and then changes back to INACTIVE.
Check the connection and condition of the UCH connectors, component code 645, the passenger compartment
fuse box, component code 1016 and the wiper stalk, component code 145.
If the connector(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
• AP9 (or AP1) between components 1016 and 211,
• MG between component 211 and the earth,
• 36G between components 145 and 211.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Check the connection and condition of the rear screen wiper motor connector, component code 211.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Check the operation and fitting of the rear screen wiper motor.
The rear screen wiper motor may need to be replaced (see MR 388 Mechanical, 85A, Wiping - Washing, Rear
screen wiper motor: Removal - Refitting).
MR-426-B90-85A000$080.mif
V4
85A-15
UCH
WIPERS – WASHERS
85A
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Fault Interpretation
Special note:
Use Wiring Diagrams Technical Note for Logan / Sandero.
Check that the windscreen park position status ET027 Windscreen park position is ACTIVE each time the wiper
blade arrives at the park position and then changes back to INACTIVE.
Check the connection and condition of the UCH connectors, component code 645.
If the connector(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance of the following connections:
• 14L between components 645 and 212,
• MB between component 212 and the earth.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Check the connection and condition of the windscreen wiper motor connector, component code 212.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Check the operation and fitting of the windscreen wiper motor.
The windscreen wiper motor may need to be replaced (see MR 388 Mechanical, 85A, Wiping - Washing,
Windscreen wiper motor: Removal - Refitting).
MR-426-B90-85A000$080.mif
V4
85A-16
UCH
WIPERS – WASHERS
85A
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Conformity check
Only perform this conformity check after a complete check with the diagnostic tool.
NOTES The values indicated in this conformity check are given as examples.
Test conditions: Engine stopped, ignition on.
UCH_V08_CCONF/UCH_V09_CCONF/UCH_V0E_CCONF/UCH_V0F_CCONF
MR-426-B90-85A000$090.mif
V4
85A-17
UCH
WIPERS – WASHERS
85A
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Status summary table
MR-426-B90-85A000$100.mif
V4
85A-18
UCH
WIPERS – WASHERS
85A
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Interpretation of statuses
Special note:
Use Wiring Diagrams Technical Note for Logan / Sandero.
Check the presence and condition of fuse F03 or F27 (20 A) in the passenger compartment
ABSENT fuse box, component code 1016 (see MR 388 Mechanical, 81C, Fuses, Fuses: List and
location of components).
Check the condition and connection of the combined wiper-washer connector, component
code 145, and check the washer pump connector, component code 677 (bent, broken tabs,
etc.).
If the connector(s) are faulty and if there is a repair procedure (see Technical Note 6015A
(Renault) or Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring:
Precautions for repair), repair the connector, otherwise replace the wiring.
Check the condition and connection of the UCH connector, component code 645 (tabs bent,
broken, etc.).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A
(Renault) or Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring:
Precautions for repair), repair the connector, otherwise replace the wiring.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A
(Renault) or Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring:
Precautions for repair), repair the wiring, otherwise replace it.
MR-426-B90-85A000$110.mif
V4
85A-19
UCH
WIPERS – WASHERS
85A
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Interpretation of statuses
ET492
CONTINUED
Check the insulation, continuity and the absence of interference resistance on the
following connection:
• 16A between components 677 and 145.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A
(Renault) or Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring:
Precautions for repair), repair the wiring, otherwise replace it.
MR-426-B90-85A000$110.mif
V4
85A-20
UCH
WIPERS – WASHERS
85A
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Interpretation of statuses
Special note:
Use Wiring Diagrams Technical Note for Logan / Sandero.
Check the presence and condition of fuse F03 or F27 (20 A) in the passenger compartment
ABSENT fuse box, component code 1016 (see MR 388 Mechanical, 81C, Fuses, Fuses: List and
location of components).
Check the connection and condition of the combined wiper-washer connector, component
code 145 and check the rear screen wiper motor connector, component code 211.
If the connector(s) are faulty and if there is a repair procedure (see Technical Note 6015A
(Renault) or Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring:
Precautions for repair), repair the connector, otherwise replace the wiring.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A
(Renault) or Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring:
Precautions for repair), repair the wiring, otherwise replace it.
MR-426-B90-85A000$110.mif
V4
85A-21
UCH
WIPERS – WASHERS
85A
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Interpretation of statuses
Special note:
Use Wiring Diagrams Technical Note for Logan / Sandero.
Check the presence and condition of fuse F03 or F27 (20 A) in the passenger compartment
ABSENT fuse box, component code 1016 (see MR 388 Mechanical, 81C, Fuses, Fuses: List and
location of components).
Check the condition and connection of the combined wiper-washer connector, component
code 145, and check the bi-directional washer pump connector, component code 677 (tabs
bent, broken, etc.).
If the connector(s) are faulty and if there is a repair procedure (see Technical Note 6015A
(Renault) or Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring:
Precautions for repair), repair the connector, otherwise replace the wiring.
Check the condition and connection of the UCH connector, component code 645 (tabs bent,
broken, etc.).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A
(Renault) or Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring:
Precautions for repair), repair the connector, otherwise replace the wiring.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A
(Renault) or Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring:
Precautions for repair), repair the wiring, otherwise replace it.
MR-426-B90-85A000$110.mif
V4
85A-22
UCH
WIPERS – WASHERS
85A
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Interpretation of statuses
ET557
CONTINUED
Check the continuity between connections MAM and 24A of the rear screen washer control.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A
(Renault) or Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring:
Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation, continuity and the absence of interference resistance on the
following connection:
• 24A between components 677 and 145.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A
(Renault) or Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring:
Precautions for repair), repair the wiring, otherwise replace it.
MR-426-B90-85A000$110.mif
V4
85A-23
UCH
WIPERS – WASHERS
85A
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Interpretation of statuses
Special note:
Use Wiring Diagrams Technical Note for Logan / Sandero.
Check the presence and condition of fuse F01 (20 A) in the passenger compartment fuse box,
ET558
component code 1016 (see MR 388 Mechanical, 81C, Fuses, Fuses: List and location of
NO
components).
Check the connection and condition of the combined wiper-washer connector, component
code 145 and check the windscreen wiper motor connector, component code 212.
If the connector(s) are faulty and if there is a repair procedure (see Technical Note 6015A
(Renault) or Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring:
Precautions for repair), repair the connector, otherwise replace the wiring.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A
(Renault) or Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring:
Precautions for repair), repair the wiring, otherwise replace it.
MR-426-B90-85A000$110.mif
V4
85A-24
UCH
WIPERS – WASHERS
85A
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Command summary table
Tool
Diagnostic tool name Comments
command
MR-426-B90-85A000$120.mif
V4
85A-25
UCH
WIPERS – WASHERS
85A
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Interpretation of commands
Special note:
Use Wiring Diagrams Technical Note for Logan / Sandero.
Check the presence and condition of fuse F03 or F27 (20 A) in the passenger compartment fuse box, component
code 1016 (see MR 388 Mechanical, 81C, Fuses, Fuses: List and location of components).
Check the connection and condition of the rear screen wiper connector, component code 211 and the wiper stalk
connector, component code 145.
If the connector(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Check the + 12 V after ignition supply on connection AP9 for the stalk, component code 145.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
Check the insulation, continuity and the absence of interference resistance of the following connections:
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
AFTER REPAIR Carry out a road test and then a check using the diagnostic tool.
UCH_V08_AC007/UCH_V09_AC007/UCH_V0E_AC007/UCH_V0F_AC007
MR-426-B90-85A000$130.mif
V4
85A-26
UCH
WIPERS – WASHERS
85A
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Interpretation of commands
LOW-SPEED WIPER
AC056
Special note:
Use Wiring Diagrams Technical Note for Logan / Sandero.
Check the presence and condition of fuse F01 (20 A) in the passenger compartment fuse box, component code
1016 (see MR 388 Mechanical, 81C, Fuses, Fuses: List and location of components).
Check the connection and condition of the windscreen wiper connector, component code 212 and the stalk
connector, component code 145.
If the connector(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Check the + 12 V after ignition supply on connection AP7 of the stalk, component code 145.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
AFTER REPAIR Carry out a road test and then a check using the diagnostic tool.
UCH_V08_AC056/UCH_V09_AC056/UCH_V0E_AC056/UCH_V0F_AC056
MR-426-B90-85A000$130.mif
V4
85A-27
UCH
WIPERS – WASHERS
85A
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Customer complaints
Only refer to these customer complaints after carrying out a complete check with
NOTES
the diagnostic tool
WIPERS - WASHERS
MR-426-B90-85A000$140.mif
V4
85A-28
UCH
WIPERS – WASHERS
85A
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Fault finding chart
Only consult this customer complaint after a complete check with the
diagnostic tool.
There must be no present or stored faults.
NOTES
Special note:
Use Wiring Diagrams Technical Note for Logan / Sandero.
Check the presence and condition of fuse F01 (20 A) in the passenger compartment fuse box, component code
1016 (see MR 388 Mechanical, 81C, Fuses, Fuses: List and location of components).
Check the + 12 V after ignition supply on connection AP7 of the stalk, component code 145.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Check that the motor operates correctly.
MR-426-B90-85A000$150.mif
V4
85A-29
UCH
WIPERS – WASHERS
85A
Vdiag No.: 08, 09, 0E,
0F
Fault finding – Fault finding chart
Only consult this customer complaint after a complete check with the
diagnostic tool.
There must be no present or stored faults.
NOTES
Special note:
Use Wiring Diagrams Technical Note for Logan / Sandero.
Check the presence and condition of fuse F01 (20 A) in the passenger compartment fuse box, component code
1016 (see MR 388 Mechanical, 81C, Fuses, Fuses: List and location of components).
Check the + 12 V after ignition supply on connection AP7 of the stalk, component code 145.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Check that the motor operates correctly.
MR-426-B90-85A000$150.mif
V4
85A-30