Professional Documents
Culture Documents
Welcome to the WELDING INSPECTIONS community, our official discussion site for Inspector. You’ll find topics on features, welding
knowledge, technical, and general support here.
Get free access articles, questions & answers, jobs and other articles by one click to sign up,
Facebook
Gmai
Twitter
Email
URL: https://weldinginspections.net
ADVERTISEMENT
The CSWIP 3. 1 multiple-choice paper 1 is a welding quiz, which will help you revise and exercise even as you look
Janforward
11 to take on
your certification exam.
1/1
1. An MMA electrode which is classified as an E6013 (according to AWS A5.1 ) is a: Jan 12
Basic type
Cellulose type
Rutile type
https://weldinginspections.net/t/cswip-3-1-multiple-choice-paper-1/190 1/7
16/5/2019 CSWIP 3.1 Multiple Choice Paper 1 - Exams / CSWIP - The Welding Inspecions Community
AC
DC electrode negative
DC electrode positive
It would make little difference which was used
Jan 11
3. A code gives the acceptance standard for excess weld metal “h” as h<=1mm+0.1b, max. 5mm; which “b” is the width of the weld
cap. For which of the following situations is the excess weld metal acceptable?
b = 15 h = 3.0
b = 22 h = 3.0
b = 28 h = 4.0
b = 40 h = 5.4
4. A fillet weld has a design throat thickness of 8mm. That is the minimum leg length that is required?
5.6mm
11.2mm
11.8mm
It can not be determined from the information given
5. The number 111 is shown at the tall-end of a weld symbol reference line. According to BS EN ISO 2553 . What does this number
indicate?
Welding process
Type of welding electrode
Welding position
Total weld length
6. Which of the following alloying elements is used mainly to improve the toughness of steels?
Chromium
Manganese
Sulphur
https://weldinginspections.net/t/cswip-3-1-multiple-choice-paper-1/190 2/7
16/5/2019 CSWIP 3.1 Multiple Choice Paper 1 - Exams / CSWIP - The Welding Inspecions Community
Carbon
Travel speed
Welding current
Arc length
Inductance
9. A large diameter pipe with a wall thickness of 10mm is to be used for a cross country pipeline. Which electrode type could be
used to combine high welding speed and deep penetration?
Basic covered
Cellulosic covered
Rutile covered
Iron power loaded
Radiographic testing
Helium leak testing
Magnetic particle testing
Ultrasonic testing
11. A transverse tensile test piece from a weld joint will give the:
https://weldinginspections.net/t/cswip-3-1-multiple-choice-paper-1/190 3/7
16/5/2019 CSWIP 3.1 Multiple Choice Paper 1 - Exams / CSWIP - The Welding Inspecions Community
12. Weldments in carbon-manganese steels, made by low heat input welding may shown
Greater ductility
Higher distortion
Higher dilution
Higher hardness
14. A drawing with symbols to BS EN ISO 2553 will show a 5mm leg fillet by which of the following:
a5
t5
z5
5z
15. Using a stabilized stainless steel will reduce the risk of:
Excessive distortion
Weld decay
Formation of iron-sulphides
Sour service cracking
Aluminum alloys
Carbon steel
Austenitic stainless steel
Copper
17. Which of the following types of imperfection is generally considered to be the most serious?
Root concavity
Buried planar
Surface breaking non-planar
18. Weldment in carbon-manganese steels, made using a heat input higher than the maximum specified by the WPS, may show:
Higher integrity
Lower distortion
Lower toughness
Higher hardness
Constant voltage
Constant current
Drooping
Pulsing
BS EN 499
BS EN 288
BS EN 22553
BS EN 287
21. A long centerline crack has been detected in a submerged arc weld bead this may be due to
https://weldinginspections.net/t/cswip-3-1-multiple-choice-paper-1/190 5/7
16/5/2019 CSWIP 3.1 Multiple Choice Paper 1 - Exams / CSWIP - The Welding Inspecions Community
Curies
kV
IQI values
The number after the isotope type
24. The included angle used for MMA welding of a 15mm thick steel single V butt joint is most likely to be:
35 Deg.
120 Deg.
70 Deg.
90 Deg.
Friction welding
Gas tungsten arc welding
Resistance welding
Laser welding
26. A typical baking temperature for basic low hydrogen electrodes is:
120 Deg. C.
350 Deg. C.
500 Deg. C.
200 Deg. C.
28. Which of the following defects will have the more severe effect on the load-bearing capacity of a weld?
https://weldinginspections.net/t/cswip-3-1-multiple-choice-paper-1/190 6/7
16/5/2019 CSWIP 3.1 Multiple Choice Paper 1 - Exams / CSWIP - The Welding Inspecions Community
Undercut.
Incompletely filled groove.
Irregular width.
Excess penetration.
29. While inspecting a weld on a 100mm thick high carbon steel plate with a … the weld is visually acceptable, however the parent
material has severse … the weld approximately 3mm deep, what course of action would you …
https://weldinginspections.net/t/cswip-3-1-multiple-choice-paper-1/190 7/7