Professional Documents
Culture Documents
RE-500 Catalogue
RE-500 Catalogue
Government Letter 69 - 70
Country of Origin 71
VOC Content Test Certificate (LEED) 72
Material Safety Data Sheet 73 - 81
Job Reference 82 - 88
Recycling one ton of paper saves 17 trees and 7000 gallons of water.
Please consider your environmental responsibility before using the hard copy version!
*All the test reports in this submission folder are abstract version with essential data for submission purpose.
For full report, please contact Hilti through our customer service hotline 8228 8118.
1 Aug 2016
SAMPLE SUBMISSION AND APPROVAL FORM
DETAILS OF SUBMISSION
From: ________________________________
The enclosed sample and catalogue* / certificate of origin* / technical data* / test report* / job reference* as
described below have been checked for compliance with the Specifications and Drawings, and are submitted for
approval.
1. General Information
a. Material Description HIT – RE500 Injection Adhesive
__________________________________________________________
__________________________________________________________
b. Location: Re-bar fastening
__________________________________________________________
__________________________________________________________
c. Specification Ref. Page: __________________________ Item: _______________________
__________________________ _______________________
__________________________ _______________________
d. Drawing Ref. No. __________________________________________________________
__________________________________________________________
__________________________________________________________
e. B.Q. Ref.No.: __________________________________________________________
__________________________________________________________
__________________________________________________________
f. Anticipated date of approval: __________________________________________________________
2. Technical Information
The submitted sample has been checked against the specification and drawings as listed below:-
Submitted Sample
Specification Requirements
(State details against each item)
a. Brand
Not specified Hilti
b. Country of Origin
Not specified Germany
c. Manufacturer’s Name & Address
Not specified Hilti Corporation, FL-9494 Principality of Liechtenstein.
Page 1 of 2
2 Aug 2016
f. Appearance
Not specified According to the sample submitted
g. Color +
Not specified Red
h. Specification
Not specified Attached
i. Manufacturer’s Catalogue
Not specified Attached
l. Supplementary Information
Not specified NIL
____________________________
(Quality Control Manager)
_____________________________
Date:
cc. _______________________________________
_______________________________________
_______________________________________
_______________________________________
(* Delete if appropriate)
(+ For glass or vitreous mosaic tiles, the contractor is required to confirm the colour range(s) of the
submitted sample, i.e. a) light and or medium; or b) dark)
Page 2 of 2
3 Aug 2016
安卡錨栓系統
技術
種鐵
化學安卡錨栓總覽
HIT-HY 200-R HIT-RE 500-SD HIT-RE 500 HIT-HY 70 HVU
頁數
HIT-Z
■ 208-209
HIT-V ■ ■ ■ ■ 206-207
HAS-E ■ ■ ■ 203-205
HIS-N ■ ■ ■ ■ ■ 205-206
HIT-SC ■
CR 套筒 ■ 208
CB 套筒 ■ ■ ■
TE-CD/YD 空心鑽頭
■ ■ ■ 100-102
VC 20/40 吸塵機
■ ■ ■ 136-138
Base materials
◾◾ Concrete (uncracked)
Applications
■ Structural connections with post-installed rebar (e.g. extension/
connection to walls, slabs, stairs, columns, foundations, etc.)
■ Substitution of misplaced/missing rebars or couplers
■ Anchoring structural steel connections (e.g. steel columns,
beams, etc.)
■ Anchoring crash barriers, noise barriers, etc.
■ Structural renovation of buildings, bridges and other civil struc-
tures, retrofitting and re-strengthening of concrete members
possible Approvals
■ Suitable for underwater applications in hammer-drilled holes ETA (ETAG 001-05, Option 7)
ETA-08/0105 for HIT-RE 500 rebar (ETAG 001-5,
Advantages Option 1)
Approvals and test reports may apply to selected products only. Please refer
■ High performance and technical superiority as per international
to the documents for details.
approvals
■ Especially suitable for large-diameter elements and/or deep
embedment depths
■ No expansion forces in concrete allow secure fastenings even
close to edges and/or with close spacing
■ Virtually odourless hence convenient to work with
■ Suitable for anchoring in diamond cored holes
■ Unique foil packaging and compatible Hilti HIT injection system
makes handling extremely easy
Technical data
SAFEset No
Seismic No
These are abbreviated instructions which may vary according to the application.
Always observe/follow the instructions accompanying the product or refer to
www.hilti.com/techlib.
Sales pack
Ordering designation Package contents Item number
quantity
HIT-RE 500/330/1 INT 1x Foil pack, 1x Mixer, 1x Mixer extension 1 pc 426675
HIT-RE 500/500/1 INT 1x Foil pack, 1x Mixer, 1x Mixer extension 1 pc 426672
Advantages
■ Dose adjustment knob for accurate and controlled dispensing
■ Fast, easy foil pack loading
■ High battery capacity (up to 100x500ml foil packs)
Sales pack
Ordering designation Weight Item number
quantity
HDE 500 CB DISPENSER KIT 1 pc 34990781)
HDE 500-A22 box 2.2 kg 1 pc 2005630
HDE 500-A22 CR/CB cas 2.2 kg 1 pc 2005637
HDE 500-A22 empty 2.4 kg 1 pc 434724
1)
This is a non-stock item. For detailed lead time information please contact your Hilti representative.
Dispenser HDM
Advantages
■ Fast, easy foil pack loading
Sales pack
Ordering designation Weight Item number
quantity
HDM 330 CB DISPENSER KIT 1 pc 34990821)
HDM 330 CB CARDBOARD BOX 1 pc 34991031)
HDM 500 CB DISPENSER KIT (2060870 W/ACC) 1 pc 3499081
HDM 330 cas 1 pc 2060429
HDM 500 cas 1 pc 2060870
HDM 330 box 1.5 kg 1 pc 2005640
HDM 500 box 1.8 kg 1 pc 2005641
1)
This is a non-stock item. For detailed lead time information please contact your Hilti representative.
Applications
■ Drilling holes for anchoring structural steel connections (e.g.
steel columns, beams)
Advantages
■ Drilling and hole cleaning in one step
Sales pack
Ordering designation Diameter Working length Length Item number
quantity
TE-YD 16/59 16 mm 400 mm 590 mm 1 pc 2018956
TE-YD 18/59 18 mm 400 mm 590 mm 1 pc 2018957 4
TE-YD 20/59 20 mm 400 mm 590 mm 1 pc 2018959
TE-YD 22/59 22 mm 400 mm 590 mm 1 pc 2018960
TE-YD 25/59 25 mm 400 mm 590 mm 1 pc 2018962
TE-YD 28/59 28 mm 400 mm 590 mm 1 pc 2018964
TE-YD 32/59 32 mm 400 mm 590 mm 1 pc 2018966
Applications
■ Drilling holes for structural connections with post-installed
rebars
Advantages
■ Drilling and hole cleaning in one step
Sales pack
Ordering designation Diameter Working length Length Item number
quantity
TE-CD 12/33 12 mm 200 mm 330 mm 1 pc 2018940
TE-CD 14/37 14 mm 240 mm 360 mm 1 pc 2018942
TE-CD 16/37 16 mm 240 mm 360 mm 1 pc 2018945
TE-CD 18/37 18 mm 240 mm 360 mm 1 pc 2018946
Customer Hotline: Hong Kong 8228 8118 Macau 00800 8228 8118 9 Aug 2016 104
Anchor Systems
Sales pack
Ordering designation Item number
quantity
Blow-out pump 1 pc 60579
Extension tube HIT-VL 16/0.7 10 pc 336646
Advantages
■ Fast, effective cleaning of drilled holes
Sales pack
Ordering designation Drill hole diameter Item number
quantity
Air nozzle HIT-DL 20 20 mm 1 pc 3717191)
Air nozzle HIT-DL 25 25 mm 1 pc 3717201)
Air nozzle HIT-DL 32 32 mm 1 pc 3717211)
1)
This is a non-stock item. For detailed lead time information please contact your Hilti representative.
Sales pack
Ordering designation Drill hole diameter Item number
quantity
Brush extension HIT-RBH 1 pc 2291381)
Brush extension HIT-RBV 1 pc 2387271)
Holder TE-Y 1 pc 2634391)
Brush extension HIT-RBS 10/0.7 1 pc 3366451)
Round brush 13 HG 12 mm 1 pc 229133
Round brush 18 HG 18 mm 1 pc 229134
Round brush 18 GA 18 mm 1 pc 2291361)
Round steel brush HIT-RB 20 20 mm 1 pc 3365521)
Round steel brush HIT-RB 25 25 mm 1 pc 3365531)
Round brush 28 HG 28 mm 1 pc 229135
Round brush 28 GA 28 mm 1 pc 2291371)
Round steel brush HIT-RB 30 30 mm 1 pc 3809201)
Round brush 38 GA 38 mm 1 pc 2296731)
Round steel brush HIT-RB 40 40 mm 1 pc 3822601)
Round steel brush HIT-RB 47 47 mm 1 pc 3822641)
Round brush 50 GA 50 mm 1 pc 2296741)
1)
This is a non-stock item. For detailed lead time information please contact your Hilti representative.
Advantages
■ Injection pistons and flexible extension hoses help ensure con-
sistent injection of the adhesive into the hole without formation
of air voids
Sales pack
Ordering designation Drill hole diameter Item number
quantity
Hose HIT-VL 11/1.0 10 pc 20425331)
Coupler VL-K 10 pc 3350211)
Piston plug HIT-SZ 20 20 mm 10 pc 20393121)
Piston plug HIT-SZ 25 25 mm 10 pc 20393151)
Piston plug HIT-SZ 30 30 mm 10 pc 20393171)
Piston plug HIT-SZ 40 40 mm 10 pc 20393251)
Piston plug HIT-SZ 47 47 mm 10 pc 20393321)
1)
This is a non-stock item. For detailed lead time information please contact your Hilti representative.
Overhead cup
Technical data
8
Dispenser, setting tool, accessory, Mixing nozzles and injection
tester type accessories
Sales pack
Ordering designation Item number
quantity
Drip guard HIT-OHC1 10 pc 387551
Drip guard HIT-OHC2 10 pc 387552
Wedge HIT-OHW 100 pc 387550
Technical data
Dispenser, setting tool, accessory, Other accessories
tester type
Sales pack
Ordering designation Item number
quantity
Safety glasses 1 pc 52051)
1)
This is a non-stock item. For detailed lead time information please contact your Hilti representative.
Customer Hotline: Hong Kong 8228 8118 Macau 00800 8228 8118 11 Aug 2016 244
Anchor Systems
Technical data
Dispenser, setting tool, accessory, Mixing nozzles and injection
tester type accessories
Sales pack
Ordering designation Item number
quantity
Mixer HIT-RE-M 1 pc 337111
Mixer HIT-M1 assy 100 pc 68156
Sales pack
Ordering designation Package contents Item number
quantity
VC 40-U 110V 1x Univ. vacuum cleaner VC 40-U 110 V 1 pc 2183451)
VC 40-U 230V 1x Univ. vacuum cleaner VC 40-U 230 V 1 pc 212300
1)
This is a non-stock item. For detailed lead time information please contact your Hilti representative.
The Best Chemical Anchor for rebar fastening under different conditions
High Performance & Safety Save Material & Labour Cost Vs
Vs other injection adhesive hard cartridge injection adhesive
✓ 40% higher tensile load in normal hole. ✓ 70% less wastage compared to hard
cartridge.
✓ 30% higher tensile load in wet and water-filled hole.
✓ Reduce disposal cost.
✓ Suitable for both drilled or diamond cored hole.
✓ Short dispensing time.
13
Widely Approved 70% MORE wastage compared to foil pack
for rebar fastening
LIMITED temperature range (20˚C to 32˚C) for
✓The only injection adhesive listed in “Fire protection cartridge dispensing
materials for structural use of Central Data Bank”.
INSUFFICIENT working time (8.5mins) at 30˚C
✓4-hour fire resistance Warrington test report. HIGHER dispensing force
✓Easy and simple loading selection table.
LACK of reference / approval
Aug 2016
1 Customer Hotline: Hong Kong 8228 8118 Macau 00800 8228 8118 (Mon - Fri 8:30 am - 6:00 pm / Sat 8:30 am - 1:00 pm) | Fast Ordering, Prompt & Free Delivery Customer Hotline: Hong Kong 8228 8118 Macau 00800 8228 8118 (Mon - Fri 8:30 am - 6:00 pm / Sat 8:30 am - 1:00 pm) | Fast Ordering, Prompt & Free Delivery 2
Technical Information
Remarks:
2
1. It is based on non-cracked concrete with strength 30N/mm ;
2
2. Yield strength of rebar fyk is 500N/mm ;
3. There is no factor of safety introduced in the ultimate mean pull out load. Please apply
appropriate factor of safety in your design;
4. Onsite pullout test can be carried out to verify the workmanship of the installation but should
not be verification of the ultimate loading. The testing load shall be subjected to the designer’s
decision but should not exceed the 0.87 x yield load to avoid permanent damage to the rebar.
5. All the spacing and edge distance requirement for reinforced concrete design should be reference to
BS8110;
6. If there is a fire resistance concern, the loading should be referred to the fire table
14 Aug 2016
Technical Information
Setting Details
Remark:
1) Please refer to ‘Detailed consumption table’ for more information
2) The filled volume was calculated by the following equation and is for reference only.
2 2
Filled volume = [(D/2) - (R/2) ] x 3.14 x I
where D = hole diameter, I = hole depth, R = rebar diameter
2) The filled volume showed in the table did not include any wastage during the installation.
3) 1 trigger pull of dispenser HDM is approx. 6 ml of RE 500.
To dispense 1 cartridge of 500ml RE 500 needs approx. 80 triggers.
Mechanical Properties
15 Aug 2016
Detailed Consumption Table
*Please note that above consumption table is based on good workmanship and
for reference only
16 Aug 2016
Detailed Consumption Table
*Please note that above consumption table is based on good workmanship and
for reference only
17 Aug 2016
Method statement of RE500 installation
18 Aug 2016
Method statement of RE500 installation
19 Aug 2016
Method statement of RE500 installation
20 Aug 2016
Method statement of RE500 installation
21 Aug 2016
Method statement of RE500 installation
22 Aug 2016
23 Aug 2016
24 Aug 2016
25 Aug 2016
26 Aug 2016
27 Aug 2016
28 Aug 2016
29 Aug 2016
30 Aug 2016
31 Aug 2016
32 Aug 2016
33 Aug 2016
34 Aug 2016
35 Aug 2016
36 Aug 2016
37 Aug 2016
38 Aug 2016
39 Aug 2016
40 Aug 2016
41 Aug 2016
42 Aug 2016
43 Aug 2016
44 Aug 2016
45 Aug 2016
46 Aug 2016
47 Aug 2016
48 Aug 2016
49 Aug 2016
50 Aug 2016
51 Aug 2016
52 Aug 2016
53 Aug 2016
54 Aug 2016
55 Aug 2016
56 Aug 2016
57 Aug 2016
58 Aug 2016
59 Aug 2016
60 Aug 2016
61 Aug 2016
62 Aug 2016
63 Aug 2016
64 Aug 2016
65 Aug 2016
66 Aug 2016
67 Aug 2016
68 Aug 2016
69 Aug 2016
70 Aug 2016
71 Aug 2016
88 Empire Drive • St. Paul, Minnesota • 55103
(651) 642-1150 • fax (651) 642-1239
Test Method: SCAQMD method 304-91 Determination of Volatile Organic Compounds (VOC)
in Various Materials as referenced by South Coast Air Quality Management
District (SCAQMD) Rule 1168. The values also comply with the requirements of
EPA test method #24.
Test Data:
Specification Product
LEED 2009 (LEED 3.0)
LEED 2.2
IEQ-4.1: Low-Emitting Materials –
Adhesives and Sealants Hilti
Green Building Council of Australia
Green Star Office Design 3.0, IEQ-13
HIT-RE 500
Green Star Office Design 2.0, IEQ-13
Green Star Office Interiors 1.1, IEQ-11
Multipurpose Construction Adhesives;
Product contains: 4 g/L of VOC
VOC Limit: 70 g/L
72 Aug 2016
Page 1/9
Safety data sheet
according to 1907/2006/EC, Article 31
Printing date 01.10.2014 Version number 8 Revision: 01.10.2014
73 Aug 2016
39.1.0
Page 2/9
Safety data sheet
according to 1907/2006/EC, Article 31
Printing date 01.10.2014 Version number 8 Revision: 01.10.2014
(Contd. of page 1)
· Hazard pictograms
Hilti HIT
74 Aug 2016
39.1.0
Page 3/9
Safety data sheet
according to 1907/2006/EC, Article 31
Printing date 01.10.2014 Version number 8 Revision: 01.10.2014
(Contd. of page 2)
· Dangerous components A:
CAS: 25068-38-6 reaction product: bisphenol-A-(epichlorhydrin) epoxy resin 25-50%
NLP: 500-033-5 (number average molecular weight = 700)
Reg.nr.: 01-2119456619-26 Xi R36/38; Xi R43; N R51/53
Aquatic Chronic 2, H411; Skin Irrit. 2, H315; Eye Irrit. 2, H319; Skin
Sens. 1, H317
CAS: 28064-14-4 Reaction product: bisphenol-F epichlorhydrin resin, MW ≤ 700 10-25%
Reg.nr.: 01-2119454392-40 Xi R36/38; Xi R43; N R51/53
Aquatic Chronic 2, H411; Skin Irrit. 2, H315; Eye Irrit. 2, H319; Skin
Sens. 1, H317
CAS: 16096-31-4 1,6-bis(2,3-epoxypropoxy)hexane 10-25%
EINECS: 240-260-4 Xi R36/38; Xi R43
Reg.nr.: 01-2119463471-41 R52/53
Skin Irrit. 2, H315; Eye Irrit. 2, H319; Skin Sens. 1, H317; Aquatic Chronic
3, H412
CAS: 30499-70-8 Trimethylolpropane, (chloromethyl)oxirane polymer 2.5-10%
Xi R36/38; Xi R43
R52/53
Skin Irrit. 2, H315; Eye Irrit. 2, H319; Skin Sens. 1, H317; Aquatic Chronic
3, H412
.
· Dangerous components B:
CAS: 1477-55-0 m-Xylylenediamine 30-40%
EINECS: 216-032-5 C R35; Xn R20/22; Xi R43
Reg.nr.: 01-2119480150-50 R52/53
Skin Corr. 1A, H314; Acute Tox. 4, H302; Acute Tox. 4, H332; Skin
Sens. 1, H317; Aquatic Chronic 3, H412
.
· SVHC None
· Additional information For the wording of the listed risk phrases refer to section 16.
75 Aug 2016
39.1.0
Page 4/9
Safety data sheet
according to 1907/2006/EC, Article 31
Printing date 01.10.2014 Version number 8 Revision: 01.10.2014
(Contd. of page 3)
· 5.3 Advice for firefighters
· Protective equipment: In the event of fire, wear self contained breathing apparatus
76 Aug 2016
39.1.0
Page 5/9
Safety data sheet
according to 1907/2006/EC, Article 31
Printing date 01.10.2014 Version number 8 Revision: 01.10.2014
(Contd. of page 4)
· Breathing equipment:
Not necessary if room is well-ventilated.
In case of brief exposure or low pollution use breathing filter apparatus. In case of intensive or longer exposure use
breathing apparatus that is independent of circulating air.
· Recommended filter device for short term use: Filter AX
· Protection of hands:
Protective gloves
Gauze goggles
Face protection
EN 166 / EN 170
· Body protection:
77 Aug 2016
39.1.0
Page 6/9
Safety data sheet
according to 1907/2006/EC, Article 31
Printing date 01.10.2014 Version number 8 Revision: 01.10.2014
(Contd. of page 5)
· Flash point: > 100 °C (DIN EN ISO 1523)
· Inflammability (solid, gaseous) Not determined
· Ignition temperature: Not determined
· Decomposition temperature: Not determined
· Self-inflammability: Product is not selfigniting.
· Danger of explosion: Product is not explosive.
· Critical values for explosion:
Lower: Not determined
Upper: Not determined
· Vapour pressure at 20 °C: 0.04 hPa
· Density Component A: 1.5 g/cm³ (DIN 51757)
Component B: 1.4 g/cm³ (DIN 51757)
· Relative density Not determined
· Vapour density Not determined
· Evaporation rate Not determined
· Solubility in / Miscibility with
Water: Unsoluble
· Partition coefficient (n-octanol/water): Not determined
· Viscosity:
dynamic at 20 °C: 50 Pas (DIN 53019)
kinematic at 20 °C: >20 s (ISO 2431)
· Solvent content:
Organic solvents: 0%
Water: 0%
· 9.2 Other information No further relevant information available.
78 Aug 2016
39.1.0
Page 7/9
Safety data sheet
according to 1907/2006/EC, Article 31
Printing date 01.10.2014 Version number 8 Revision: 01.10.2014
(Contd. of page 6)
Corrosive
Irritant
Swallowing will lead to a strong caustic effect on mouth and throat and to the danger of perforation of esophagus and
stomach.
· CMR effects (carcinogenity, mutagenicity and toxicity for reproduction) None
79 Aug 2016
39.1.0
Page 8/9
Safety data sheet
according to 1907/2006/EC, Article 31
Printing date 01.10.2014 Version number 8 Revision: 01.10.2014
(Contd. of page 7)
· Uncleaned packagings:
· Recommendation:
Disposal must be made according to official regulations.
Dispose of packaging according to regulations on the disposal of packagings.
Empty packs: May be disposed via the local Green Dot collecting system (valpak) or EAK waste material code 150102
(plastic packaging materials)
80 Aug 2016
39.1.0
Page 9/9
Safety data sheet
according to 1907/2006/EC, Article 31
Printing date 01.10.2014 Version number 8 Revision: 01.10.2014
(Contd. of page 8)
81 Aug 2016
39.1.0
Job / Application Reference
Product Name: HILTI RE 500
701-704 Tower A, Manulife Fiancial Centre, 223 Wai Yip Street, Kwun Tong, Kwoloon , Hong Kong
Hotline: 8228 8118 1
82 Aug 2016
Job / Application Reference
Product Name: HILTI RE 500
701-704 Tower A, Manulife Fiancial Centre, 223 Wai Yip Street, Kwun Tong, Kwoloon , Hong Kong
Hotline: 8228 8118 2
83 Aug 2016
Job / Application Reference
Product Name: HILTI RE 500
701-704 Tower A, Manulife Fiancial Centre, 223 Wai Yip Street, Kwun Tong, Kwoloon , Hong Kong
Hotline: 8228 8118 3
84 Aug 2016
Job / Application Reference
Product Name: HILTI RE 500
701-704 Tower A, Manulife Fiancial Centre, 223 Wai Yip Street, Kwun Tong, Kwoloon , Hong Kong
Hotline: 8228 8118 4
85 Aug 2016
Job / Application Reference
Product Name: HILTI RE 500
701-704 Tower A, Manulife Fiancial Centre, 223 Wai Yip Street, Kwun Tong, Kwoloon , Hong Kong
Hotline: 8228 8118 5
86 Aug 2016
Job / Application Reference
Product Name: HILTI RE 500
701-704 Tower A, Manulife Fiancial Centre, 223 Wai Yip Street, Kwun Tong, Kwoloon , Hong Kong
Hotline: 8228 8118 6
87 Aug 2016
Job / Application Reference
Product Name: HILTI RE 500
701-704 Tower A, Manulife Fiancial Centre, 223 Wai Yip Street, Kwun Tong, Kwoloon , Hong Kong
Hotline: 8228 8118 7
88 Aug 2016