Professional Documents
Culture Documents
0
MMR Elevator_SI Doc. No.
DL
EL) 06-008
FOD Test & Commissioning for Page 1/20
Field Industrial Engineering SI210 Controller Date July. 2006
R1 A C D = 0 4 [ 0 1 ] 0 0 %
R2 E 0 0 0 - 0 0 1 0 0 0 0 S
R3 1 1 0 0 1 1 0 0 0 0 1 1 1 0 1
R4 K :
1) Row 1 : Operation mode, present floor, load weight and speed of elevator.
① ACD=27(Column1~ 6) : Operation Code( ex: 27*Auto operation, 4*Maintenance
operation...) ※ Refer to the MODE Description
② 01FL(Column 8 ~11) : Present floor
③ 00%(Column 13 ~ 16) : On stop, present load weight (%) of the elevator.
2) Row 2 : When an error occurs, it shows the trouble code of the top level error,
condition of the operation, output of main signal and direction of elevator.
① E000(Column 2 ~ 4) : Trouble code of top level error.(TCD No. 1 ~ 255)
ex)
031 DC LINK Overvoltage 116 POSI ON error(LDU)
3) Row 3 : Displays input condition of main signal such as switches, relays and
contactor, etc.
C1 R5SC C5 LDC C9 C1ST C13 CDS
C2 48V C6 LDCX C10 C1BR C14 DCLS
C3 UL C7 SDS1D C11 SUPPRESS C15 DOLS
C4 DL C8 SDS1U C12 LDS C16 SES
- "1" : Means that switches, relay and contactors, etc. are operating.
- "0" : Means that switches, relay and contactors, etc. are not operating.
06 Earthquake control 07 Earthquake ctrl slow opr 08 Bottom F slow opr (Spec.ROM F height error)
09 F/H measurement prep. 0A F height meas. Opr 0B Bottom F slow opr (C.RAM F height error)
nd
0C Unused 0D Unused 0E 2 fire opr
0F 1st fire operation 10 Arrival opr finished 11 All Fs opr after earthquake ctrl
1E EGN driven opr finished 1F EGN driven opr 20 CP temp.detecting opr finished
3. Annunciator Mode
Row 2 Data
Max. acceleration and Jerk of 1st deceleration zone according to setting of T9 and T10.
Row 4 Data
shelter plate fixing distance
A23E = Error TRACE Data read (Error TRACE DATA clear A22E $3FF2 =>”00”)
** Screen check **
1. "TRC X-Y" will be displayed after input A23E
X : Traced Total Block No. Y : Present Block No.
Screen of A23E
A C D = 0 3 [ F ] 5 0 %
E 0 0 0 - 0 0 1 0 0 0 0 S
Item No. 0 0 : 5 0 0 0 = 0 8 2 4 1 6 2 2
T R C 5 3 0- 1 K :
Address
2. To read the Item No. on the higher, input '0' or lower , input '8'
ex) If you input '0' two times on A23E initial screen, indicates as below.(Address will
be increase 4 per one)
LCD Screen
A C D = 0 3 [ F ] 5 0 %
E 0 0 0 - 0 0 1 0 0 0 0 S
0 2 : 5 0 0 8 = 0 0 0 0 0 0 9 1
T R C 3 - 1 K :
3.To clear the value of Data number, input 'CCCC'. But, number 1~9 are impossible to clear.
ex) If you input "CCCC"at data number 12, the original data will be changed to '0'.
LCD Screen Note] The Units of statistic data
A C D = 2 7 [ F ] 5 0 % 1) Distance [km]
E 0 0 0 - 0 0 1 0 0 0 0 S
2) Time [hh:mm:ss]
1 2 = 0 c n t
C C C C 3) Count [cnt]
S T A D A T A K :
4) Rate [%]
4.To cancel A25E mode, input 'FFFF'
A C D = 2 7 [ F ] 5 0 %
E 0 0 0 - 0 0 1 0 0 0 0 S
S T A D A T A R E S E T
[ E ] E N T E R K :
Total Traced data count The rank of the present Traced data count
2. Row 2 "FL=" Emergency stop occurred floor, "DATA=" The reason of the emergency stop,
it is related toTCD 164.
Row 3 "DATE=" Data of emergency stop occurred time. (Occur on July. 10th 16:15 at
5th floor by safety circuit off)
3. '0' key for displaying the next data and before data is displayed by '8' key.
To clear all data has been stored, input 'CCCC' and auto-reset the mode.
'FFFF' is reset this mode without data clear
Rev. No. 0
MMR Elevator_SI Doc. No.
DL
EL) 06-008
FOD Test & Commissioning for Page 11/20
Field Industrial Engineering SI210 Controller Date July. 2006
Indicates 'LOAD ?' at Row 4, input the percentage of the loaded weights with decimal value.
ex) 50% --> 050E, 60% --> 060E
I:0 0 0 0 0 0 0 0
DOOR Error #1
DOOR Error #2
DOOR Error #3
** Door Error **
** Caution **
Door Error3 Door Error2 Door Error1
1.In case the site has applied
Position error 0 0 1 SAV1,MAV1,DAV1,HAV1
** Check point **
1). Dip S/W setting condition of Floor ID on DHG PCB.(HEX value)
2). DC 24V check between HA connector 3 and 4 .
3). Check if light on of B/T lamp till 2~3sec after press the B/T under HA is connected
condition.
4). Check if IND Digital, Direction lamp, Additional lamp(Inspect ,Full) are in due order
flickling.
5). Separates the HA connector from DHG PCB, when above 2,4 items are normal
condition.
6). Repeats above 1)~5)items on each floors B/T.
§ Separates the HA connector from DHG PCB, when all indicators are turned off for
protection of PCB from electric shock.
2. To cancel A82E mode, input 'FFFF'.
Row 4 "WD:XXX%" XXX means changed load data from load sensors input loads.
2. To cancel A86E mode, input 'FFFF'.
A87E = 110% Function test mode
** Screen Check **
1. "110-> " will be displayed at Row 4 after input A87E.
LCD Screen
A C D = 2 7 [ F ] 0 4 %
E 0 0 0 - 0 0 1 0 0 0 0 S
1 1 0 0 1 0 0 0 0 0 1 1 1 0 0
1 1 0 - > K :
Breakdown time
Each 2 digit display Month,
A C D = 2 7 [ 1 2 ] 1 0 % day, hour, minute
E 2 2 3 - 0 0 0 5 1 5 1 4 2 0 May 15th14H 20M
C n t = 3 0 0 0 0 0 0 0 0
L O G 1 1 - 0 1 K : Trouble solved time
Trouble code
Rev. No. 0
MMR Elevator_SI Doc. No.
DL
EL) 06-008
FOD Test & Commissioning for Page 17/20
Field Industrial Engineering SI210 Controller Date July. 2006
23 22 21 20 19 18 17 16 15 14 13 12
R5SX SCS R5SC SUPRS C1ST C1BR DOLS LDS CDS LDU LDC LDD
11 10 9 8 7 6 5 4 3 2 1 0
Maint
UL SD1U SD2U SD2D SD1D DL SHOE RDMC High R1MM CLS
M
7 6 5 4 3 2 1 0
R5SC SUPRS C1ST C1BR R2OP R2CL R1ML R2DM
Rev. No. 0
MMR Elevator_SI Doc. No.
DL
EL) 06-008
FOD Test & Commissioning for Page 18/20
Field Industrial Engineering SI210 Controller Date July. 2006
TCD 5 10 56 70 74 92 96 97 98 99 114
Servo Hexa High DOC Gear ΦB ON CLS CLS R5SC OFF
0
speed (CAR)
Mode Normal OLS OLS R2LD
(Russia
3
Additional Information Bit
m/c
room)
7 6 5 4
No. maint
ANN Floor Normal
9
No. (CAR)
Dispatc
D C B A
h
Spec
SVC.
2 step-
decelera
E
t-ion
time
F
TCD
F E D C B A 9 8 7 6 5 4 3 2 1 0
ON
OFF
error
error
116
FOD
ON
OFF
error
error
117
Field Industrial Engineering
lsion
ation
switch.
SD2D
SD1U
SD1D
SD2U
119
Compu
deceler
Counted speed in operation
controller when error
detected.
126
Hexadecimal
Value (m/min)
OLS
RDZ
MMR Elevator_SI
CDS
detected
132
Test & Commissioning for
OLS
RDZ
CDS
detected
133
LDS
CLS
OLS
Doc. No.
RDZ
CDS
detected
134
OLS
CDS
detected
0
135
DL
speed
Over R5SC Off LDS Down Door error 3
speed On
2
error
Operation LDS Off OLS Up On
3
error error
Floor CDS Off Abnormal
height speed when
4
when power
Bit
fault
Safety cut IN CAR SDS Over
6
On Speed
Error Abnormal
7
Off
C1BR Off
A 9
C1ST Off
DL
B
activated
UL
C
activated
E D
F
Bit #0 is reset.
Refer to “A71E”
Remark
error detected
mode in ANN
manual
of error
of error
of error
of error
of error