Professional Documents
Culture Documents
INA
134
INA
213
INA134
4
INA
134
INA
213
4
INA2134
V–
International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 • Twx: 910-952-1111
Internet: http://www.burr-brown.com/ • FAXLine: (800) 548-6133 (US/Canada Only) • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132
INA134PA, UA
INA2134PA, UA
PARAMETER CONDITIONS MIN TYP MAX UNITS
AUDIO PERFORMANCE
Total Harmonic Distortion + Noise, f = 1kHz VIN = 10Vrms 0.0005 %
Noise Floor(1) 20kHz BW –100 dBu
Headroom(1) THD+N < 1% +23 dBu
FREQUENCY RESPONSE
Small-Signal Bandwidth 3.1 MHz
Slew Rate 14 V/µs
Settling Time: 0.1% 10V Step, CL = 100pF 2 µs
0.01% 10V Step, CL = 100pF 3 µs
Overload Recovery Time 50% Overdrive 3 µs
Channel Separation (dual), f = 1kHz 117 dB
OUTPUT NOISE VOLTAGE(2)
f = 20Hz to 20kHz 7 µVrms
f = 1kHz 52 nV/√HZ
OFFSET VOLTAGE(3)
Input Offset Voltage VCM = 0V ±100 ±1000 µV
vs Temperature Specified Temperature Range ±2 µV/°C
vs Power Supply VS = ±4V to ±18V ±5 ±60 µV/V
INPUT
Common-Mode Voltage Range: Positive VO = 0V 2(V+)–5 2(V+)–4 V
Negative VO = 0V 2(V–)+5 2(V–)+2 V
Differential Voltage Range See Typical Curve
Common-Mode Rejection VCM = ±31V, RS = 0Ω 74 90 dB
Impedance(4)
Differential 50 kΩ
Common-Mode 50 kΩ
GAIN
Initial 1 V/V
Error VO = –16V to 16V ±0.02 ±0.1 %
vs Temperature ±1 ±10 ppm/°C
Nonlinearity VO = –16V to 16V 0.0001 %
OUTPUT
Voltage Output, Positive (V+)–2 (V+)–1.8 V
Negative (V–)+2 (V–)+1.6 V
Current Limit, Continuous to Common ±60 mA
Capacitive Load (Stable Operation) 500 pF
POWER SUPPLY
Rated Voltage ±18 V
Voltage Range ±4 ±18 V
Quiescent Current (per Amplifier) IO = 0 ±2.4 ±2.9 mA
TEMPERATURE RANGE
Specification Range –40 85 °C
Operation Range –55 125 °C
Storage Range –55 125 °C
Thermal Resistance, θJA
8-Pin DIP 100 °C/W
SO-8 Surface-Mount 150 °C/W
14-Pin DIP 80 °C/W
SO-14 Surface-Mount 100 °C/W
NOTES: (1) dBu = 20log (Vrms /0.7746). (2) Includes effects of amplifier’s input current noise and thermal noise contribution of resistor network.
(3) Includes effects of amplifier’s input bias and offset currents. (4) 25kΩ resistors are ratio matched but have ±25% absolute value.
The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes
no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change
without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant
any BURR-BROWN product for use in life support devices and/or systems.
INA134/2134 2
PIN CONFIGURATIONS
Top View 8-Pin DIP/SO-8 Top View 14-Pin DIP/SO-14
Ref 1 8 NC NC 1 14 Ref A
V– 4 5 Sense V– 4 11 V+
+In B 5 10 Sense B
NC = No Connection B
–In B 6 9 Out B
NOTE: (1) Stresses above these ratings may cause permanent damage.
(2) One channel per package.
ELECTROSTATIC
DISCHARGE SENSITIVITY
PACKAGE/ORDERING INFORMATION
This integrated circuit can be damaged by ESD. Burr-Brown
PACKAGE SPECIFICATION recommends that all integrated circuits be handled with ap-
DRAWING TEMPERATURE
PRODUCT PACKAGE NUMBER(1) RANGE propriate precautions. Failure to observe proper handling and
Single
installation procedures can cause damage.
INA134PA 8-Pin DIP 006 –40°C to +85°C ESD damage can range from subtle performance degradation
INA134UA SO-8 Surface-Mount 182 –40°C to +85°C
to complete device failure. Precision integrated circuits may
Dual
INA2134PA 14-Pin DIP 010 –40°C to +85°C
be more susceptible to damage because very small parametric
INA2134UA SO-14 Surface-Mount 235 –40°C to +85°C changes could cause the device not to meet its published
NOTE: (1) For detailed drawing and dimension table, please see end of data
specifications.
sheet, or Appendix C of Burr-Brown IC Data Book.
3 INA134/2134
TYPICAL PERFORMANCE CURVES
At TA = +25°C, VS = ±18V, unless otherwise noted.
DIM (%)
0.010 0.1 RL = 2kΩ, 600Ω
RL = 100kΩ
RL = 2kΩ
0.001 0.010
RL = 600Ω
0.0001 0.001
20 100 1k 10k 20k –10 –5 0 5 10 15 20 25
Frequency (Hz) Output Amplitude (dBu)
f = 1kHz
Amplitude (% of Fundamental)
2nd Harmonic
0.010 0.0001
RL = 600Ω
( noise limited)
RL = 2kΩ,
0.001 0.00001 3rd Harmonic
RL = 2kΩ,
100kΩ
VO = 1Vrms
0.0001 0.000001
0 5 10 15 20 25 30 20 100 1k 10k 20k
Output Amplitude (dBu) Frequency (Hz)
1k 10
100 1
10 0.1
1 10 100 1k 10k 100k 1M 1 10 100 1k 10k 100k
Frequency (Hz) Frequency (Hz)
INA134/2134 4
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C, VS = ±18V, unless otherwise noted.
60
–10
40
–20
20
–30 0
1k 10k 100k 1M 10M 1k 10k 100k 1M
Frequency (Hz) Frequency (Hz)
RL = 100kΩ
100
Power Supply Rejection (dB)
40
100
+PSR
20
0 90
100 1k 10k 100k 1M 20 100 1k 10k 20k
Frequency (Hz) Frequency (Hz)
20
30
Output Voltage (Vp-p)
10
0
20
–10
–20
10 –30
VREF = 0V
–40
RL = 2kΩ
0 –50
100 1k 10k 100k 1M 10M –20 –15 –10 –5 0 5 10 15 20
Frequency (Hz) Output Voltage (V)
5 INA134/2134
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C, VS = ±18V, unless otherwise noted.
–SR
14
Quiescent Current (mA)
3
+SR
1 10
0 8
–75 –50 –25 0 25 50 75 100 125 –75 –50 –25 0 25 50 75 100 125
Temperature (°C) Temperature (°C)
60
Short-Circuit Current (mA)
40
Quiescent Current (mA)
+ISC
2
20
–20
–ISC 1
–40
–60
–80 0
–75 –50 –25 0 25 50 75 100 125 ±4 ±6 ±8 ±10 ±12 ±14 ±16 ±18
Temperature (°C) Supply Voltage (V)
15 15
10 10
5 5
0 0
–1000
–900
–800
–700
–600
–500
–400
–300
–200
–100
0
100
200
300
400
500
600
700
800
900
1000
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
6.5
7
7.5
8
8.5
9
9.5
10
10.5
11
11.5
12
INA134/2134 6
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C, VS = ±18V, unless otherwise noted.
SMALL-SIGNAL OVERSHOOT
OUTPUT VOLTAGE SWING vs OUTPUT CURRENT vs LOAD CAPACITANCE
17 70
16 –55°C
60
15
Output Voltage Swing (V)
25°C
14 50
125°C
13
Overshoot (%)
85°C 40
12
–12 30
85°C
–13 125°C
–14 20
–15 RL = 2kΩ
25°C 10
–55°C 100mV Step
–16
–17 0
0 ±20 ±40 ±60 ±80 ±100 0 400 800 1200 1600 2000
Output Current (mA) Load Capacitance (pF)
CL = 100pF
50mV/div
5V/div
CL = 500pF
1µs/div 1µs/div
7 INA134/2134
APPLICATIONS INFORMATION
V– V+
Figure 1 shows the basic connections required for operation
of the INA134. Decoupling capacitors are strongly recom- 1µF 1µF
INA134/2134 8
INA134
2 5
INA134
V1
6 1/2
V0 = V1 + V2 –In 2 5
1 OPA2134
V1
R2
V2
3
6
R1
V0
R2
FIGURE 3. Precision Summing Amplifier. 0utput
1/2 3 1
V2 OPA2134
INA134 +In
2 5
–In
VO = (1 + 2R2/R1) (V2 –V1)
6 3 6
BUF634 VO
The difference amplifier is a highly versatile building • Precision Summing Instrumentation Amplifier
block that is useful in a wide variety of applications. See • Precision Absolute Value Buffer
the INA105 data sheet for additional applications ideas,
• Precision Voltage-to-Current Converter with Differential
including:
Inputs
• Current Receiver with Compliance to Rails • Differential Input Voltage-to-Current Converter for Low
• Precision Unity-Gain Inverting Amplifier IOUT
• ±10V Precision Voltage Reference • Isolating Current Source
• ±5V Precision Voltage Reference • Differential Output Difference Amplifier
• Precision Unity-Gain Buffer • Isolating Current Source with Buffering Amplifier for
• Precision Average Value Amplifier Greater Accuracy
• Precision G = 2 Amplifier • Window Comparator with Window Span and Window
Center Inputs
• Precision Summing Amplifier
• Precision Voltage-Controlled Current Source with Buff-
• Precision G = 1/2 Amplifier
ered Differential Inputs and Gain
• Precision Bipolar Offsetting
• Digitally Controlled Gain of ±1 Amplifier
• Precision Summing Amplifier with Gain
• Instrumentation Amplifier Guard Drive Generator
9 INA134/2134
PACKAGE OPTION ADDENDUM
www.ti.com 6-Dec-2006
PACKAGING INFORMATION
Orderable Device Status (1) Package Package Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Type Drawing Qty
INA134PA ACTIVE PDIP P 8 50 Green (RoHS & CU NIPDAU N / A for Pkg Type
no Sb/Br)
INA134PAG4 ACTIVE PDIP P 8 50 Green (RoHS & CU NIPDAU N / A for Pkg Type
no Sb/Br)
INA134UA ACTIVE SOIC D 8 100 Green (RoHS & CU NIPDAU Level-3-260C-168 HR
no Sb/Br)
INA134UA/2K5 ACTIVE SOIC D 8 2500 Pb-Free CU NIPDAU Level-3-260C-168 HR
(RoHS)
INA134UA/2K5E4 ACTIVE SOIC D 8 2500 Pb-Free CU NIPDAU Level-3-260C-168 HR
(RoHS)
INA134UAE4 ACTIVE SOIC D 8 100 Green (RoHS & CU NIPDAU Level-3-260C-168 HR
no Sb/Br)
INA134UAG4 ACTIVE SOIC D 8 100 Green (RoHS & CU NIPDAU Level-3-260C-168 HR
no Sb/Br)
INA2134PA ACTIVE PDIP N 14 25 Green (RoHS & CU NIPDAU N / A for Pkg Type
no Sb/Br)
INA2134UA ACTIVE SOIC D 14 58 Pb-Free CU NIPDAU Level-3-260C-168 HR
(RoHS)
INA2134UA/2K5 ACTIVE SOIC D 14 2500 Green (RoHS & CU NIPDAU Level-3-260C-168 HR
no Sb/Br)
INA2134UA/2K5E4 ACTIVE SOIC D 14 2500 Pb-Free CU NIPDAU Level-3-260C-168 HR
(RoHS)
INA2134UA/2K5G4 ACTIVE SOIC D 14 2500 Green (RoHS & CU NIPDAU Level-3-260C-168 HR
no Sb/Br)
INA2134UAE4 ACTIVE SOIC D 14 58 Pb-Free CU NIPDAU Level-3-260C-168 HR
(RoHS)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com 6-Dec-2006
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products Applications
Amplifiers amplifier.ti.com Audio www.ti.com/audio
Data Converters dataconverter.ti.com Automotive www.ti.com/automotive
DSP dsp.ti.com Broadband www.ti.com/broadband
Interface interface.ti.com Digital Control www.ti.com/digitalcontrol
Logic logic.ti.com Military www.ti.com/military
Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork
Microcontrollers microcontroller.ti.com Security www.ti.com/security
Low Power Wireless www.ti.com/lpw Telephony www.ti.com/telephony
Video & Imaging www.ti.com/video
Wireless www.ti.com/wireless