Professional Documents
Culture Documents
for dishwashers
The model numbers quoted refer only to the basic model number, e.g. the
G 641 SCi is described as the G 641 in this booklet.
2
Contents
3
Installing a freestanding dishwasher
Freestanding dishwashers
Freestanding dishwashers do not
require any special installation fixings in
the kitchen, (except for plumbing and
electrical connection points. See
relevant sections at the end of this
booklet).
^ The dishwasher must be level and
stable when installed.
^ Any unevenness in the floor level can
be compensated for by adjusting the
four screw feet.
Depending on model
the adjustment range is:
– G 601 - G 632 2 cm
(85-87 cm total height)
– G 646 - G 698, G 975 4 cm
(85-89 cm total height)
4
Installing integrated "i" Dishwashers
Integrated ("i") dishwashers
"i" dishwashers are specially designed
,To ensure stability, "i" and "U" mo-
del dishwashers must only be
for building under a continuous
installed under a continuous worktop
worktop.
which must be securely screwed to
– The control panel with its neighbouring units.
accessories is included with the "i"
dishwasher in a separate package
for on-site fixing. ,The dishwasher must not be
installed under a hob. The high
– The front of the dishwasher is
radiant temperatures which are
designed to take a front panel. It can
sometimes generated by a hob
be fitted with a base unit door front to
could damage the dishwasher.
match the rest of the kitchen.
– The dishwasher does not have a
plinth facia. The plinth area of the ,On dishwashers with a drying
dishwasher needs to be covered fan, moist air is expelled through the
either with a plinth facing to match vent outlet in the front of the machine
the kitchen furniture or with another at the end of a programme. It
facia. The separate plinth facia can continues to be expelled for a
be height adjusted to suit the certain length of time or until the
kitchen. The plinth return is freely door is opened.
adjustable. To prevent damaging surrounding
fittings (e. g. worktops with wood
Instructions for installing the
edging) the fan running time can be
dishwasher are described in the
increased by 14 minutes (see
following sections.
"Additional functions" in the
Operating Instruction manual for the
An "i" model dishwasher can be machine).
converted into a built-under "U"
dishwasher.
– A decor set GDU must be used.
– A plinth facia to cover the plinth area
is supplied with the decor set. The
plinth facia can be adjusted to match
the height of adjacent plinths. The
plinth return is freely adjustable.
The decor set is supplied with a
separate installation booklet.
5
Installing integrated "i" Dishwashers
Building in dimensions
Dishwasher models G 601 - G 632 Dishwasher models G 801 - G 832
6
Installing integrated "i" Dishwashers
7
Installing integrated "i" Dishwashers
^ Attach cap a to push button switch. ^ Place the facia panel c in position
and use the six screws d to screw in
^ Push the ventillation grille b
place through from the inside of the
(depending on model) into position
door.
so that the slats on the grille are
facing downwards. ^ Attach selector e.
8
Installing integrated "i" Dishwashers
Dishwashers with programme selector buttons
(G 632, G 692 - G 696, G 832, G 892 - G 896)
^ Attach cap a to push button switch. ^ Place the facia panel c in position and
use the six screws d to screw in place
^ Push the ventillation grille b into
through from the inside of the door.
position so that the slats on the grille
are facing downwards. ^ Insert programme selector buttons e
and function buttons f (the number of
buttons will depend on model).
Dishwashers with programme buttons (G 698, G 898)
^ Attach cap a to push button switch. ^ Place the facia panel c in position
and use the six screws d to screw in
^ Push the ventillation grille b into
place through from the inside of the
position so that the slats on the grille
door.
are facing downwards.
9
Installing integrated "i" Dishwashers
feet.
^ Fit the slides - with the ratchet at the
rear - under the screw feet.
10
Installing integrated "i" Dishwashers
Securing pieces Angle support
To ensure stability, the dishwasher must The angle support for the water
be fixed securely to the worktop (step drainage hose at the rear of the
6). Two securing pieces are supplied dishwasher can be turned.
for this purpose.
^ Turn the angle support in the
direction of the on-site connection for
the drainage hose.
11
Installing integrated "i" Dishwashers
Front screw feet
Now adjust the feet until the seal on
the top of the dishwasher is right up
against the underside of the
worktop, to which it will be screwed
later. Ensure that the dishwasher
stands level.
12
Installing integrated "i" Dishwashers
13
Installing integrated "i" Dishwashers
Thickness:
the same thickness as the neighbouring
door fronts but a minimum of 16 mm.
^ On each side of the fixing bracket
Height: position a template with the rule
Dimension X markings facing outwards.
14
Installing integrated "i" Dishwashers
^ Take off the fixing bracket.
^ Lay the door front down with the rear
side facing upwards.
15
Installing integrated "i" Dishwashers
Fitting and securing the door front
16
Installing integrated "i" Dishwashers
^ Adjust the door front height on one Once the door front is correctly
side and lightly screw in a T20 Torx positioned:
screw on this side.
^ Open the dishwasher door.
^ Adjust the door front height on the
^ Tighten all the Torx screws on the
other side and also lightly screw in a
sides.
T20 Torx screw on this side.
^ Plug the openings for the fixing
^ Close the dishwasher door.
screws using the plastic stoppers
^ Check the alignment of the door provided.
panel.
^ If it is not correctly aligned you may
,Door fronts differ in weight and it
is therefore essential that the door
need to loosen the screws and re-
springs are adjusted after the door
adjust it to the correct alignment.
front has been fitted. See Step 7.
17
Installing integrated "i" Dishwashers
18
Installing integrated "i" Dishwashers
19
Installing integrated "i" Dishwashers
8. Matching the plinth facia of a ^ Place the plinth facia directly in front
kitchen run of the kitchen run but do not attach.
The plinth area of the dishwasher is ^ Carefully open the dishwasher door.
normally covered with a plinth run If the door front comes into contact with
matching the kitchen furniture. the kitchen plinth when the dishwasher
door is opened the plinth facia in the
area around the dishwasher door
needs to be cut to size.
^ To do this mark where the edge of the
door front comes into contact with the
plinth facia.
^ Cut the plinth facia to size along this
line.
^ Place the plinth facia in front of the
kitchen run again and check whether
the dishwasher door can be opened
fully.
If it cannot, trim the plinth facia to the
The height (H) of the plinth facia around correct size.
the dishwasher depends on the plinth
return (R) and how much the door front ^ Secure the plinth facia to the
extends below the dishwasher door (P). adjacent kitchen units.
20
Installing integrated "i" Dishwashers
For kitchens utilizing a Dishwasher model G 6XX
non-continuous plinth facia (see data plate for model number)
The included plinth facia will fit without
modification when:
– The machine is set to its maximum
height (legs fully extended), and
– the toekick is recessed as far as
possible (100 mm).
If the machine height is less than
maximum, or if the plinth facia is
recessed less than 100 mm, the plinth
facia must be shortened (see following
page).
21
Installing integrated "i" Dishwashers
Trimming the plinth facia
23
Plumbing
25
Special accessories
Freestanding dishwasher
You would like to... Then you need ...
26
Technical data
27
Technical data
28
Technical data
29
Technical data
30
31
Alteration rights reserved (NovoPlusB,P,S) / 2006 M.-Nr. 05 591 312 / 01
en - AUS