Professional Documents
Culture Documents
Single/Dual/Quad 220MHz,
1500V/µs Operational Amplifiers
with Programmable Supply Current
FEATURES DESCRIPTION
n 220MHz Gain-Bandwidth Product The LT®1815/LT1816/LT1817 are low power, high speed,
n 1500V/μs Slew Rate very high slew rate operational amplifiers with excellent
n 6.5mA Supply Current per Amplifier DC performance. The LT1815/LT1816/LT1817 feature
n Programmable Current Option higher bandwidth and slew rate, much lower input offset
n 6nV/√Hz Input Noise Voltage voltage and lower noise and distortion than other devices
n Unity-Gain Stable with comparable supply current. A programmable current
n 1.5mV Maximum Input Offset Voltage option (LT1815 and LT1816A) allows power savings and
n 8μA Maximum Input Bias Current flexibility by operating at reduced supply current and speed.
n 800nA Maximum Input Offset Current The circuit topology is a voltage feedback amplifier with the
n 50mA Minimum Output Current, VOUT = ±3V slewing characteristics of a current feedback amplifier.
n ±3.5V Minimum Input CMR, VS = ±5V
The output drives a 100Ω load to ±3.8V with ±5V supplies.
n Specified at ±5V, Single 5V Supplies
On a single 5V supply, the output swings from 1V to 4V
n Operating Temperature Range: –40°C to 85°C
with a 100Ω load connected to 2.5V. Harmonic distortion
n Space Saving MSOP and SSOP Packages
is –70dB for a 5MHz, 2VP-P output driving a 100Ω load
n Low Profile (1mm) SOT-23 (ThinSOT™) and Leadless
in a gain of –1.
DFN Packages
The LT1815/LT1816/LT1817 are manufactured on Linear
APPLICATIONS Technology’s advanced low voltage complementary bipolar
process and are available in a variety of TSOT-23, SO,
n Wideband Amplifiers
MSOP, SSOP and leadless DFN packages.
n Buffers
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear
n Active Filters Technology Corporation. ThinSOT is a trademark of Linear Technology Corporation. All other
n Video and RF Amplification trademarks are the property of their respective owners.
n Communication Receivers
n Cable Drivers
n Data Acquisition Systems
3RD HARMONIC
2ND HARMONIC
500Ω –60
–
LT1815 VOUT –70
VIN
+ 100Ω 2ND HARMONIC
–80
ISET FULL SPEED MODE
3RD HARMONIC
–90
HS/LP
40k
–100
100k 1M 10M
–5V
181567 TA01 FREQUENCY (Hz)
181567 TA02
181567fb
1
LT1815/LT1816/LT1817
ABSOLUTE MAXIMUM RATINGS (Note 1)
Total Supply Voltage (V+ to V–) ............................. 12.6V Specified Temperature Range (Note 8) ....–40°C to 85°C
Differential Input Voltage Maximum Junction Temperature ......................... 150°C
(Transient Only, Note 2) ........................................... ±6V (DD Package) .................................................... 125°C
Input Voltage ........................................................... ±VS Storage Temperature Range .................. –65°C to 150°C
Output Short-Circuit Duration (Note 3) .......... Indefinite (DD Package) ..................................... –65°C to 125°C
Operating Temperature Range .................–40°C to 85°C Lead Temperature (Soldering, 10 sec)................... 300°C
PIN CONFIGURATION
LT1815 LT1815 LT1815
TOP VIEW
TOP VIEW TOP VIEW
NC 1 8 NC
OUT 1 5 V+ OUT 1 6 V+
–IN 2 – 7 V+
V– 2 V– 2 5 ISET +
+ – + – +IN 3 6 OUT
+IN3 4 –IN +IN 3 4 –IN
V– 4 5 NC
S5 PACKAGE S6 PACKAGE
5-LEAD PLASTIC TSOT-23 6-LEAD PLASTIC TSOT-23 S8 PACKAGE
TJMAX = 150°C, θJA = 250°C/W (NOTE 9) TJMAX = 150°C, θJA = 230°C/W (NOTE 9) 8-LEAD PLASTIC SO
TJMAX = 150°C, θJA = 150°C/W (NOTE 9)
LT1816 LT1816 LT1816
TOP VIEW
TOP VIEW
OUT A 1 8 V+ TOP VIEW
OUT A 1 10 V+
–IN A 2 7 OUT B OUTA 1 8 V+
9 –IN A 2 9 OUT B
A –INA 2 7 OUTB A
+IN A 3 6 –IN B A +IN A 3 8 –IN B
+INA 3 6 –INB B
B B V– 4 7 +IN B
V– 4 5 +IN B V– 4 5 +INB V– 5 6 ISET
MS8 PACKAGE MS PACKAGE
8-LEAD PLASTIC MSOP 10-LEAD PLASTIC MSOP
DD PACKAGE
8-LEAD (3mm × 3mm) PLASTIC DFN TJMAX = 150°C, θJA = 250°C/W (NOTE 9) TJMAX = 150°C, θJA = 250°C/W (NOTE 9)
TJMAX = 125°C, θJA = 160°C/W (NOTE 9)
UNDERSIDE METAL INTERNALLY CONNECTED TO V–
LT1816 LT1817 LT1817
TOP VIEW
TOP VIEW
OUT A 1 16 OUT D
TOP VIEW OUT A 1 14 OUT D
–IN A 2 – – 15 –IN D
A D –IN A 2 – – 13 –IN D
OUT A 1 8 V+ +IN A 3 + + 14 +IN D A D
+IN A 3 + + 12 +IN D
–IN A 2 7 OUT B V+ 4 13 V–
A V+ 4 11 V–
+IN A 3 6 –IN B +IN B 5 + + 12 +IN C
B B C +IN B 5 + + 10 +IN C
V– 4 +IN B –IN B 6 – – 11 –IN C B C
5 – – 8 –IN C
–IN B 6
OUT B 7 10 OUT C
S8 PACKAGE OUT B 7 8 OUT C
8-LEAD PLASTIC SO NC 8 9 NC
TJMAX = 150°C, θJA = 150°C/W (NOTE 9) S PACKAGE
GN PACKAGE 14-LEAD PLASTIC SO
16-LEAD PLASTIC SSOP NARROW
TJMAX = 150°C, θJA = 100°C/W
TJMAX = 150°C, θJA = 135°C/W
181567fb
2
LT1815/LT1816/LT1817
ORDER INFORMATION
SPECIFIED
LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE
LT1815CS5#PBF LT1815CS5#TRPBF LTUP 5-Lead Plastic TSOT-23 0°C to 70°C
LT1815IS5#PBF LT1815IS5#TRPBF LTVC 5-Lead Plastic TSOT-23 –40°C to 85°C
LT1815CS6#PBF LT1815CS6#TRPBF LTUL 6-Lead Plastic TSOT-23 0°C to 70°C
LT1815IS6#PBF LT1815IS6#TRPBF LTVD 6-Lead Plastic TSOT-23 –40°C to 85°C
LT1815CS8#PBF LT1815CS8#TRPBF 1815 8-Lead Plastic SO 0°C to 70°C
LT1815IS8#PBF LT1815IS8#TRPBF 1815I 8-Lead Plastic SO –40°C to 85°C
LT1816CDD#PBF LT1816CDD#TRPBF LAAR 8-Lead (3mm × 3mm) Plastic DFN 0°C to 70°C
LT1816IDD#PBF LT1816IDD#TRPBF LAAR 8-Lead (3mm × 3mm) Plastic DFN –40°C to 150°C
LT1816CMS8#PBF LT1816CMS8#TRPBF LTWA 8-Lead Plastic MSOP 0°C to 70°C
LT1816IMS8#PBF LT1816IMS8#TRPBF LTNQ 8-Lead Plastic MSOP –40°C to 85°C
LT1816ACMS#PBF LT1816ACMS#TRPBF LTYA 10-Lead Plastic MSOP 0°C to 70°C
LT1816AIMS#PBF LT1816AIMS#TRPBF LTXX 10-Lead Plastic MSOP –40°C to 85°C
LT1816CS8#PBF LT1816CS8#TRPBF 1816 8-Lead Plastic SO 0°C to 70°C
LT1816IS8#PBF LT1816IS8#TRPBF 1816I 8-Lead Plastic SO –40°C to 85°C
LT1817CGN#PBF LT1817CGN#TRPBF 1817 16-Lead Plastic SSOP 0°C to 70°C
LT1817IGN#PBF LT1817IGN#TRPBF 1817I 16-Lead Plastic SSOP –40°C to 85°C
LT1817CS#PBF LT1817CS#TRPBF LT1817CS 14-Lead Plastic SO 0°C to 70°C
LT1817IS#PBF LT1817IS#TRPBF LT1817IS 14-Lead Plastic SO –40°C to 85°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C (Note 8). VS = ±5V, VCM = 0V, unless otherwise noted. For the
programmable current option (LT1815S6 or LT1816A), the ISET pin must be connected to V– through 75Ω or less, unless
otherwise noted.
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
VOS Input Offset Voltage (Note 4) 0.2 1.5 mV
TA = 0°C to 70°C l 2.0 mV
TA = –40°C to 85°C l 3.0 mV
Input Offset Voltage LT1815S6/LT1816A, 40kΩ Between ISET and V – 2 7 mV
(Low Power Mode) (Note 10) TA = 0°C to 70°C l 9 mV
TA = –40°C to 85°C l 10 mV
ΔVOS Input Offset Voltage Drift TA = 0°C to 70°C (Note 7) l 10 15 μV/°C
ΔT TA = –40°C to 85°C (Note 7) l 10 30 μV/°C
IOS Input Offset Current 60 800 nA
TA = 0°C to 70°C l 1000 nA
TA = –40°C to 85°C l 1200 nA
IB Input Bias Current –2 ±8 μA
TA = 0°C to 70°C l ±10 μA
TA = –40°C to 85°C l ±12 μA
181567fb
3
LT1815/LT1816/LT1817
ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C (Note 8). VS = ±5V, VCM = 0V, unless otherwise noted. For the
programmable current option (LT1815S6 or LT1816A), the ISET pin must be connected to V– through 75Ω or less, unless
otherwise noted.
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
en Input Noise Voltage Density f = 10kHz 6 nV/√Hz
in Input Noise Current Density f = 10kHz 1.3 pA/√Hz
RIN Input Resistance VCM = ±3.5V 1.5 5 MΩ
Differential 750 kΩ
CIN Input Capacitance 2 pF
VCM Input Voltage Range Guaranteed by CMRR ±3.5 ±4.2 V
TA = –40°C to 85°C l ±3.5 V
CMRR Common Mode Rejection Ratio VCM = ±3.5V 75 85 dB
TA = 0°C to 70°C l 73 dB
TA = –40°C to 85°C l 72 dB
Minimum Supply Voltage Guaranteed by PSRR ±1.25 ±2 V
TA = –40°C to 85°C l ±2 V
PSRR Power Supply Rejection Ratio VS = ±2V to ±5.5V 78 97 dB
TA = 0°C to 70°C l 76 dB
TA = –40°C to 85°C l 75 dB
Channel Separation VOUT = ±3V, RL = 100Ω, LT1816/LT1817 82 100 dB
TA = 0°C to 70°C l 81 dB
TA = –40°C to 85°C l 80 dB
AVOL Large-Signal Voltage Gain VOUT = ±3V, RL = 500Ω 1.5 3 V/mV
TA = 0°C to 70°C l 1.0 V/mV
TA = –40°C to 85°C l 0.8 V/mV
VOUT = ±3V, RL = 100Ω 0.7 2.5 V/mV
TA = 0°C to 70°C l 0.5 V/mV
TA = –40°C to 85°C l 0.4 V/mV
VOUT Maximum Output Swing RL = 500Ω, 30mV Overdrive ±3.8 ±4.1 V
TA = 0°C to 70°C l ±3.7 V
TA = –40°C to 85°C l ±3.6 V
RL = 100Ω, 30mV Overdrive ±3.50 ±3.8 V
TA = 0°C to 70°C l ±3.25 V
TA = –40°C to 85°C l ±3.15 V
IOUT Maximum Output Current VOUT = ±3V, 30mV Overdrive ±50 ±80 mA
TA = 0°C to 70°C l ±45 mA
TA = –40°C to 85°C l ±40 mA
Maximum Output Current LT1815S6/LT1816A; 40kΩ Between ISET and V –;
(Low Power Mode) (Note 10) VOUT = ±3V, 30mV Overdrive ±50 ±75 mA
TA = 0°C to 70°C l ±40 mA
TA = –40°C to 85°C l ±30 mA
ISC Output Short-Circuit Current VOUT = 0V, 1V Overdrive (Note 3) ±100 ±200 mA
TA = 0°C to 70°C l ±90 mA
TA = –40°C to 85°C l ±70 mA
SR Slew Rate AV = –1 (Note 5) 900 1500 V/μs
TA = 0°C to 70°C l 750 V/μs
TA = –40°C to 85°C l 600 V/μs
FPBW Full-Power Bandwidth 6VP-P (Note 6) 80 MHz
181567fb
4
LT1815/LT1816/LT1817
ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C (Note 8). VS = ±5V, VCM = 0V, unless otherwise noted. For the
programmable current option (LT1815S6 or LT1816A), the ISET pin must be connected to V– through 75Ω or less, unless
otherwise noted.
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
GBW Gain-Bandwidth Product f = 200kHz, RL = 500Ω, LT1815 150 220 MHz
TA = 0°C to 70°C l 140 MHz
TA = –40°C to 85°C l 130 MHz
f = 200kHz, RL = 500Ω, LT1816/LT1817 140 220 MHz
TA = 0°C to 70°C l 130 MHz
TA = –40°C to 85°C l 120 MHz
Gain-Bandwidth Product LT1815S6/LT1816A; 40kΩ Between ISET and V –;
(Low Power Mode) (Note 10) f = 200kHz, RL = 500Ω 35 55 MHz
TA = 0°C to 70°C l 30 MHz
TA = –40°C to 85°C l 25 MHz
–3dB BW –3dB Bandwidth AV = 1, RL = 500Ω 350 MHz
t r, t f Rise Time, Fall Time AV = 1, 10% to 90%, 0.1V, RL = 100Ω 1 ns
tPD Propagation Delay AV = 1, 50% to 50%, 0.1V, RL = 100Ω 1.4 ns
OS Overshoot AV = 1, 0.1V; RL = 100Ω 25 %
tS Settling Time AV = –1, 0.1%, 5V 15 ns
THD Total Harmonic Distortion AV = 2, f = 5MHz, VOUT = 2VP-P, RL = 500Ω –70 dB
dG Differential Gain AV = 2, VOUT = 2VP-P, RL = 150Ω 0.08 %
dP Differential Phase AV = 2, VOUT = 2VP-P, RL = 150Ω 0.04 Deg
ROUT Output Resistance AV = 1, f = 1MHz 0.20 Ω
IS Supply Current LT1815 6.5 7 mA
TA = 0°C to 70°C l 9 mA
TA = –40°C to 85°C l 10 mA
LT1816/LT1817, per Amplifier 6.5 7.8 mA
TA = 0°C to 70°C l 10.5 mA
TA = –40°C to 85°C l 11.5 mA
Supply Current (Low Power Mode) LT1815S6/LT1816A, 40kΩ Between ISET and V –,
(Note 10) per Amplifier 1 1.5 mA
TA = 0°C to 70°C l 1.8 mA
TA = –40°C to 85°C l 2.0 mA
ISET ISET Pin Current (Note 10) LT1815S6/LT1816A –150 –100 μA
TA = 0°C to 70°C l –175 μA
TA = –40°C to 85°C l –200 μA
181567fb
5
LT1815/LT1816/LT1817
ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temp-
erature range, otherwise specifications are at TA = 25°C (Note 8). VS = 5V, OV; VCM = 2.5V, RL to 2.5V, unless otherwise noted. For the
programmable current option (LT1815S6 or LT1816A), the ISET pin must be connected to V– through 75Ω or less, unless otherwise noted.
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
VOS Input Offset Voltage (Note 4) 0.4 2.0 mV
TA = 0°C to 70°C l 2.5 mV
TA = –40°C to 85°C l 3.5 mV
Input Offset Voltage LT1815S6/LT1816A, 40kΩ Between ISET and V – 2 7 mV
(Low Power Mode) (Note 10) TA = 0°C to 70°C l 9 mV
TA = –40°C to 85°C l 10 mV
ΔVOS Input Offset Voltage Drift TA = 0°C to 70°C (Note 7) l 10 15 μV/°C
ΔT TA = –40°C to 85°C (Note 7) l 10 30 μV/°C
IOS Input Offset Current 60 800 nA
TA = 0°C to 70°C l 1000 nA
TA = –40°C to 85°C l 1200 nA
IB Input Bias Current –2.4 ±8 μA
TA = 0°C to 70°C l ±10 μA
TA = –40°C to 85°C l ±12 μA
en Input Noise Voltage Density f = 10kHz 6 nV/√Hz
in Input Noise Current Density f = 10kHz 1.3 pA/√Hz
RIN Input Resistance VCM = 1.5V to 3.5V 1.5 5 MΩ
Differential 750 kΩ
CIN Input Capacitance 2 pF
VCM Input Voltage Range (High) Guaranteed by CMRR 3.5 4.1 V
TA = –40°C to 85°C l 3.5 V
Input Voltage Range (Low) Guaranteed by CMRR 0.9 1.5 V
TA = –40°C to 85°C l 1.5 V
CMRR Common Mode Rejection Ratio VCM = 1.5V to 3.5V 73 82 dB
TA = 0°C to 70°C l 71 dB
TA = –40°C to 85°C l 70 dB
Channel Separation VOUT = 1.5V to 3.5V, RL = 100Ω, LT1816/LT1817 81 100 dB
TA = 0°C to 70°C l 80 dB
TA = –40°C to 85°C l 79 dB
Minimum Supply Voltage Guaranteed by PSRR 2.5 4 V
TA = –40°C to 85°C l 4 V
A VOL Large-Signal Voltage Gain VOUT = 1.5V to 3.5V, RL = 500Ω 1.0 2 V/mV
TA = 0°C to 70°C l 0.7 V/mV
TA = –40°C to 85°C l 0.6 V/mV
VOUT = 1.5V to 3.5V, RL = 100Ω 0.7 1.5 V/mV
TA = 0°C to 70°C l 0.5 V/mV
TA = –40°C to 85°C l 0.4 V/mV
VOUT Maximum Output Swing (High) RL = 500Ω, 30mV Overdrive 3.9 4.2 V
TA = 0°C to 70°C l 3.8 V
TA = –40°C to 85°C l 3.7 V
RL = 100Ω, 30mV Overdrive 3.7 4 V
TA = 0°C to 70°C l 3.6 V
TA = –40°C to 85°C l 3.5 V
VOUT Maximum Output Swing (Low) RL = 500Ω, 30mV Overdrive 0.8 1.1 V
TA = 0°C to 70°C l 1.2 V
TA = –40°C to 85°C l 1.3 V
RL = 100Ω, 30mV Overdrive 1 1.3 V
TA = 0°C to 70°C l 1.4 V
TA = –40°C to 85°C l 1.5 V
181567fb
6
LT1815/LT1816/LT1817
ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temp-
erature range, otherwise specifications are at TA = 25°C (Note 8). VS = 5V, OV; VCM = 2.5V, RL to 2.5V, unless otherwise noted. For the
programmable current option (LT1815S6 or LT1816A), the ISET pin must be connected to V– through 75Ω or less, unless otherwise noted.
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
IOUT Maximum Output Current VOUT = 1.5V or 3.5V, 30mV Overdrive ±30 ±50 mA
TA = 0°C to 70°C l ±25 mA
TA = –40°C to 85°C l ±20 mA
Maximum Output Current LT1815S6/LT1816A; 40kΩ Between ISET and V –;
(Low Power Mode) (Note 10) VOUT = 1.5V or 3.5V, 30mV Overdrive ±30 ±50 mA
TA = 0°C to 70°C l ±25 mA
TA = –40°C to 85°C l ±20 mA
ISC Output Short-Circuit Current VOUT = 2.5V, 1V Overdrive (Note 3) ±80 ±140 mA
TA = 0°C to 70°C l ±70 mA
TA = –40°C to 85°C l ±50 mA
SR Slew Rate AV = –1 (Note 5) 450 750 V/μs
TA = 0°C to 70°C l 375 V/μs
TA = –40°C to 85°C l 300 V/μs
FPBW Full-Power Bandwidth 2VP-P (Note 6) 120 MHz
GBW Gain-Bandwidth Product f = 200kHz, RL = 500Ω, LT1815 140 200 MHz
TA = 0°C to 70°C l 130 MHz
TA = –40°C to 85°C l 120 MHz
f = 200kHz, RL = 500Ω, LT1816/LT1817 130 200 MHz
TA = 0°C to 70°C l 110 MHz
TA = –40°C to 85°C l 100 MHz
Gain-Bandwidth Product LT1815S6/LT1816A; 40kΩ Between ISET and V –;
(Low Power Mode) (Note 10) f = 200kHz, RL = 500Ω 30 50 MHz
TA = 0°C to 70°C l 25 MHz
TA = –40°C to 85°C l 20 MHz
–3dB BW –3dB Bandwidth A V = 1, RL = 500Ω 300 MHz
t r, t f Rise Time, Fall Time A V = 1, 10% to 90%, 0.1V, RL = 100Ω 1.2 ns
tPD Propagation Delay A V = 1, 50% to 50%, 0.1V, RL = 100Ω 1.5 ns
OS Overshoot A V = 1, 0.1V; RL = 100Ω 25 %
tS Settling Time A V = –1, 0.1%, 2V 15 ns
THD Total Harmonic Distortion A V = 2, f = 5MHz, VOUT = 2VP-P, RL = 500Ω –65 dB
dG Differential Gain A V = 2, VOUT = 2VP-P, RL = 150Ω 0.08 %
dP Differential Phase A V = 2, VOUT = 2VP-P, RL = 150Ω 0.13 Deg
ROUT Output Resistance A V = 1, f = 1MHz 0.24 Ω
IS Supply Current LT1815 6.3 8 mA
TA = 0°C to 70°C l 10 mA
TA = –40°C to 85°C l 11 mA
LT1816/LT1817, per Amplifier 6.3 9 mA
TA = 0°C to 70°C l 12 mA
TA = –40°C to 85°C l 13 mA
Supply Current (Low Power Mode) LT1815S6/LT1816A, 40kΩ Between ISET and V–, per Amplifier 0.9 1.5 mA
(Note 10) TA = 0°C to 70°C l 1.8 mA
TA = –40°C to 85°C l 2.0 mA
ISET ISET Pin Current (Note 10) LT1815S6/LT1816A –150 –100 μA
TA = 0°C to 70°C l –175 μA
TA = –40°C to 85°C l –200 μA
Note 1: Stresses beyond those listed under Absolute Maximum Ratings Note 2: Differential inputs of ±6V are appropriate for transient operation
may cause permanent damage to the device. Exposure to any Absolute only, such as during slewing. Large sustained differential inputs can cause
Maximum Rating condition for extended periods may affect device excessive power dissipation and may damage the part.
reliability and lifetime.
181567fb
7
LT1815/LT1816/LT1817
ELECTRICAL CHARACTERISTICS
Note 3: A heat sink may be required to keep the junction temperature expected to meet the extended temperature limits, but are not tested at
below absolute maximum when the output is shorted indefinitely. –40°C and 85°C. The LT1815I/LT1816I/LT1817I are guaranteed to meet the
Note 4: Input offset voltage is pulse tested and is exclusive of warm-up extended temperature limits.
drift. Note 9: Thermal resistance (θJA) varies with the amount of PC board
Note 5: Slew rate is measured between ±2V at the output with ±3V input metal connected to the package. The specified values are for short
for ±5V supplies and 2VP-P at the output with a 3VP-P input for single 5V traces connected to the leads. If desired, the thermal resistance can be
supplies. substantially reduced by connecting Pin 2 of the TSOT-23, Pin 4 of the
Note 6: Full-power bandwidth is calculated from the slew rate: SO-8 and MS8, Pin 5 of the MS10 or the underside metal of the DD
package to a large metal area.
FPBW = SR/2πVP
Note 10: A resistor of 40k or less is required between the ISET and V– pins
Note 7: This parameter is not 100% tested.
of the LT1815S6 and the LT1816AMS. See the Applications Information
Note 8: The LT1815C/LT1816C/LT1817C are guaranteed to meet specified section for information on selecting a suitable resistor.
performance from 0°C to 70°C and are designed, characterized and
10
–1.0
–1.5
8
VS = ±5V –2.0
VS = ±2.5V
6 –2
2.0
4
1.5
–3
1.0
2
0.5
0 V– –4
–50 –25 0 25 50 75 100 125 0 1 2 3 4 5 6 7 –5.0 –2.5 0 2.5 5.0
TEMPERATURE (°C) SUPPLY VOLTAGE (±V) INPUT COMMON MODE VOLTAGE (V)
181567 G01 181567 G02
181567 G03
Input Bias Current vs Temperature Input Noise Spectral Density Open-Loop Gain vs Resistive Load
0 100 10 75.0
TA = 25°C TA = 25°C
–0.4 VS = ±5V
72.5
INPUT CURRENT NOISE (pA/Hz)
AV = 101
INPUT VOLTAGE NOISE (nV/Hz)
INPUT BIAS CURRENT (μA)
RS = 10k
OPEN-LOOP GAIN (dB)
–0.8
70.0
in VS = ±5V
–1.2
10 1 67.5
–1.6 en
VS = ±2.5V
VS = ±5V 65.0
–2.0
VS = ±2.5V 62.5
–2.4
181567fb
8
LT1815/LT1816/LT1817
TYPICAL PERFORMANCE CHARACTERISTICS
Output Voltage Swing Output Voltage Swing
Open-Loop Gain vs Temperature vs Supply Voltage vs Load Current
75.0 V+ 5
VS = ±5V TA = 25°C TA = 25°C
VO = ±3V –0.5 ΔVOS = 30mV VS = ±5V
RL = 500Ω
72.5 ΔVOS = 30mV
4
RL = 500Ω –1.5
70.0 SOURCE
–2.0 –2 3
67.5
RL = 100Ω SINK
2.0 –3 2
65.0
1.5
RL = 100Ω
1.0 –4
62.5
RL = 500Ω
0.5
60.0 V– –5
–50 –25 0 25 50 75 100 125 0 1 2 3 4 5 6 7 –120 –80 –40 0 40 80 120
TEMPERATURE (°C) SUPPLY VOLTAGE (±V) OUTPUT CURRENT (mA) 181567 G09
181567 G07 181567 G08
SINK 10
80 50
AV = 1
0.1
25 ΔVOS = 30mV
40
VOUT = ±3V FOR VS = ±5V
TA = 25°C
VOUT = ±1V FOR VS = ±2.5V
VS = ±5V
0 0 0.01
–50 –25 0 25 50 75 100 125 –50 –25 0 25 50 75 100 125 10k 100k 1M 10M 100M
TEMPERATURE (°C) TEMPERATURE (°C) FREQUENCY (Hz)
181567 G10 181567 G11 181567 G12
PHASE
30 ±2.5V 80
±5V
20 60 180 40
PHASE MARGIN –5
10 40 VS = ±5V
0 20 38
TA = 25°C PHASE MARGIN
–10 AV = –1 0 VS = ±2.5V
RF = RG = 500Ω
–20 –20 36 –10
10k 100k 1M 10M 100M 500M –50 –25 0 25 50 75 100 125 1M 10M 100M 500M
FREQUENCY (Hz) TEMPERATURE (°C) FREQUENCY (Hz)
181567 G13 181567 G14 181567 G15
181567fb
9
LT1815/LT1816/LT1817
TYPICAL PERFORMANCE CHARACTERISTICS
Gain Bandwidth and Phase
Gain vs Frequency, AV = 2 Gain vs Frequency, AV = –1 Margin vs Supply Voltage
10 5 240
RL = 500Ω TA = 25°C GBW
220 RL = 500Ω
RL = 500Ω
200
GAIN (dB)
GAIN (dB)
0 160 45
PHASE MARGIN
–5 RL = 100Ω
TA = 25°C TA = 25°C
–5 A = 2 AV = –1 40
V
VS = ±5V VS = ±5V
RF = RG = 500Ω RF = RG = 500Ω PHASE MARGIN
CF = 1pF CF = 1pF RL = 500Ω
–10 –10 35
1M 10M 100M 300M 1M 10M 100M 300M 0 1 2 3 4 5 6 7
FREQUENCY (Hz) FREQUENCY (Hz) SUPPLY VOLTAGE (±V)
181567 G16 181567 G17 181567 G18
Power Supply Rejection Ratio Common Mode Rejection Ratio Supply Current
vs Frequency vs Frequency vs Programming Resistor
100 100 7
TA = 25°C TA = 25°C VS = ±5V
POWER SUPPLY REJECTION RATIO (dB)
AV = 1 VS = ±5V TA = 25°C
6
VS = ±5V PER AMPLIFIER
80 80
3
40 40
2
20 20
1
0 0 0
1k 10k 100k 1M 10M 100M 1k 10k 100k 1M 10M 100M 10 100 1k 10k 40k
FREQUENCY (Hz) FREQUENCY (Hz) RSET PROGRAMMING RESISTOR (Ω)
181567 G19 181567 G20
181567 G21
150 1200
RL = 100Ω 800
SR+
100 900
SR–
600
50 600
0 300 400
10 100 1k 10k 40k 0 1 2 3 4 5 6 7 8 0 1 2 3 4 5 6 7
RSET PROGRAMING RESISTOR (Ω) INPUT STEP (VP-P) SUPPLY VOLTAGE (±V)
181567 G23 181567 G24
181567 G22
181567fb
10
LT1815/LT1816/LT1817
TYPICAL PERFORMANCE CHARACTERISTICS
Differential Gain and Phase
Slew Rate vs Temperature vs Supply Voltage Distortion vs Frequency, AV = 2
2400 –30
TA = 25°C AV = 2
DIFFERENTIAL GAIN 0.10 VS = ±5V
2000 SR+ RL = 150Ω –40 VO = 2VP-P
0.08
1600
DISTORTION (dB)
SR– 0.12 0.04
–60
VS = ±5V
1200 0.10 0.02
SR+
VS = ±2.5V 0.08 0 –70
800 DIFFERENTIAL PHASE
0.06 2ND HARMONIC
RL = 150Ω –80
SR–
AV = –1 VS = ±2.5V 0.04 3RD HARMONIC
400
RF = RG = RL = 500Ω –90
0.02
(NOTE 5)
0 0 –100
–50 –25 0 25 50 75 100 125 4 6 8 10 12 100k 1M 10M
TEMPERATURE (°C) TOTAL SUPPLY VOLTAGE (V) FREQUENCY (Hz)
181567 G25 181567 G26 181567 G27
Small-Signal Transient,
Distortion vs Frequency, AV = –1 Distortion vs Frequency, AV = 1 AV = –1
–30 –30
AV = –1 AV = 1
VS = ±5V VS = ±5V
–40 VO = 2VP-P –40 VO = 2VP-P
RL = 100Ω RL = 100Ω
–50 –50
DISTORTION (dB)
DISTORTION (dB)
–60 –60
–70 –70
2ND HARMONIC
–80 –80
2ND HARMONIC
3RD HARMONIC 181567 G30
–90 –90
3RD HARMONIC
–100 –100
100k 1M 10M 100k 1M 10M
FREQUENCY (Hz) FREQUENCY (Hz)
181567 G29
181567 G28
181567fb
11
LT1815/LT1816/LT1817
APPLICATIONS INFORMATION
Layout and Passive Components closed-loop operation, this does not increase power dis-
sipation significantly because of the low duty cycle of the
As with all high speed amplifiers, the LT1815/LT1816/
transient inputs. Sustained differential inputs, however,
LT1817 require some attention to board layout. A ground
will result in excessive power dissipation and therefore
plane is recommended and trace lengths should be mini-
this device should not be used as a comparator.
mized, especially on the negative input lead.
Low ESL/ESR bypass capacitors should be placed directly Capacitive Loading
at the positive and negative supply (0.01μF ceramics are The LT1815/LT1816/LT1817 are optimized for high band-
recommended). For high drive current applications, ad- width and low distortion applications. They can drive a
ditional 1μF to 10μF tantalums should be added. capacitive load of 10pF in a unity-gain configuration and
The parallel combination of the feedback resistor and gain more with higher gain. When driving a larger capacitive
setting resistor on the inverting input combine with the load, a resistor of 10Ω to 50Ω should be connected be-
input capacitance to form a pole that can cause peaking tween the output and the capacitive load to avoid ringing
or even oscillations. If feedback resistors greater than 1k or oscillation. The feedback should still be taken from the
are used, a parallel capacitor of value: output so that the resistor will isolate the capacitive load
to ensure stability.
CF > RG • CIN /RF
should be used to cancel the input pole and optimize dy- Slew Rate
namic performance. For applications where the DC noise
The slew rate of the LT1815/LT1816/LT1817 is propor-
gain is 1 and a large feedback resistor is used, CF should
tional to the differential input voltage. Therefore, highest
be greater than or equal to CIN. An example would be an
slew rates are seen in the lowest gain configurations.
I-to-V converter.
For example, a 5V output step in a gain of 10 has a 0.5V
Input Considerations input step, whereas in unity gain there is a 5V input step.
The LT1815/LT1816/LT1817 are tested for a slew rate
The inputs of the LT1815/LT1816/LT1817 amplifiers are in a gain of –1. Lower slew rates occur in higher gain
connected to the base of an NPN and PNP bipolar transis- configurations.
tor in parallel. The base currents are of opposite polarity
and provide first-order bias current cancellation. Due to Programmable Supply Current
variation in the matching of NPN and PNP beta, the polar- (LT1815/LT1816A)
ity of the input bias current can be positive or negative.
In order to operate the LT1815S6 or LT1816A at full speed
The offset current, however, does not depend on beta
(and full supply current), connect the ISET pin to the nega-
matching and is tightly controlled. Therefore, the use of tive supply through a resistance of 75Ω or less.
balanced source resistance at each input is recommended
for applications where DC accuracy must be maximized. To adjust or program the supply current and speed of the
For example, with a 100Ω source resistance at each input, LT1815S6 or LT1816A, connect an external resistor (RSET)
the 800nA maximum offset current results in only 80μV of between the ISET pin and the negative supply, as shown in
extra offset, while without balance the 8μA maximum input Figure 1. The amplifiers are fully functional with 0 ≤ RSET
bias current could result in a 0.8mV offset contribution. ≤ 40k. Figures 2 and 3 show how the gain bandwidth and
supply current vary with the value of the programming
The inputs can withstand differential input voltages of resistor RSET. In addition, the Electrical Characteristics sec-
up to 6V without damage and without needing clamping tion of the data sheet specifies maximum supply current
or series resistance for protection. This differential input and offset voltage, as well as minimum gain bandwidth
voltage generates a large internal current (up to 80mA), and output current at the maximum RSET value of 40k.
which results in the high slew rate. In normal transient
181567fb
12
LT1815/LT1816/LT1817
APPLICATIONS INFORMATION
5V Power Dissipation
– V+ The LT1815/LT1816/LT1817 combine high speed and large
LT1815S6
output drive in small packages. It is possible to exceed
+ V–
the maximum junction temperature specification (150°C)
ISET
under certain conditions. Maximum junction temperature
RSET (TJ) is calculated from the ambient temperature (TA), power
–5V
181567 F01 dissipation per amplifier (PD) and number of amplifiers
(n) as follows:
Figure 1. Programming Resistor Between ISET and V–
TJ = TA + (n • PD • θJA)
Power dissipation is composed of two parts. The first is
due to the quiescent supply current and the second is due
250
VS = p5V to on-chip dissipation caused by the load current. The
TA = 25°C
200
worst-case load induced power occurs when the output
voltage is at one-half of either supply voltage (or the
GAIN BANDWIDTH (MHz)
RL = 500Ω
150
maximum swing if less than one-half the supply voltage).
RL = 100Ω
Therefore, PDMAX is:
100 PDMAX = (V+ – V–) • (ISMAX) + (V+/2)2/RL or
50 PDMAX = (V+ – V–) • (ISMAX) + (V+ – VOMAX) • (VOMAX/RL)
Example: LT1816IS8 at 85°C, VS = ±5V, RL=100Ω
0
10 100 1k 10k
RSET PROGRAMING RESISTOR (Ω)
40k
PDMAX = (10V) • (11.5mA) + (2.5V)2/100Ω = 178mW
181567 F02
TJMAX = 85°C + (2 • 178mW) • (150°C/W) = 138°C
Figure 2. Gain Bandwidth Product vs RSET Programming Resistor
Circuit Operation
The LT1815/LT1816/LT1817 circuit topology is a true volt-
age feedback amplifier that has the slewing behavior of a
7
VS = ±5V current feedback amplifier. The operation of the circuit can
6
TA = 25°C
PER AMPLIFIER
be understood by referring to the Simplified Schematic.
Complementary NPN and PNP emitter followers buffer
SUPPLY CURRENT (mA)
5
the inputs and drive an internal resistor. The input volt-
4 age appears across the resistor, generating current that
3 is mirrored into the high impedance node.
2 Complementary followers form an output stage that buf-
1
fers the gain node from the load. The input resistor, input
stage transconductance and the capacitor on the high
0
10 100 1k 10k 40k
impedance node determine the bandwidth. The slew rate
RSET PROGRAMMING RESISTOR (Ω) is determined by the current available to charge the gain
181567 F03
node capacitance. This current is the differential input
Figure 3. Supply Current vs RSET Programming Resistor voltage divided by R1, so the slew rate is proportional to
the input step. Highest slew rates are therefore seen in
the lowest gain configurations.
181567fb
13
LT1815/LT1816/LT1817
SIMPLIFIED SCHEMATIC (One Amplifier)
V+
BIAS
CONTROL
R1 +IN
–IN OUT
C
ISET
V–
181567 SS
LT1815S6/LT1816AMS ONLY
TYPICAL APPLICATIONS
R5 R4
220Ω 10k
R1 R2
10k 1k
– R3
1/2 1k
LT1816 –
1/2
– + LT1816
VOUT
VIN +
+
GAIN © ¸ ©1 ¦ µ ¦
¨ R4 · ¨ ¥ 1 ´ ¥ R2 R3 ´ R2 R3
µ
·¸ 102
©ª R3 ¸¹ ©© § 2 ¶ § R1 R4 ¶ R5 ¸
¸¹
ª
TRIM R5 FOR GAIN 181567 TA03
TRIM R1 FOR COMMON MODE REJECTION
BW = 2MHz
181567fb
14
LT1815/LT1816/LT1817
TYPICAL APPLICATIONS
Photodiode Transimpedance Amplifier
1pF 1pF
4.75k
PHOTODIODE 5V
SIEMENS/
INFINEON
SFH213
–
LT1815
+ OUTPUT OFFSET ≤1mV TYPICAL
–5V BANDWIDTH = 30MHz
–5V
10% TO 90% RISE TIME = 22ns
OUTPUT NOISE (20MHz BW) = 300μVP-P
181567 TA04
4.75k 0.01μF
232Ω 274Ω
47pF
22pF
232Ω 665Ω –
VIN
274Ω 562Ω –
220pF 1/2 LT1816
+ VOUT
470pF 1/2 LT1816
+
181567 TA05
181567fb
15
LT1815/LT1816/LT1817
PACKAGE DESCRIPTION
S5 Package
5-Lead Plastic TSOT-23
(Reference LTC DWG # 05-08-1635)
1.22 REF
1.50 – 1.75
3.85 MAX 2.62 REF 1.4 MIN 2.80 BSC
(NOTE 4)
PIN ONE
0.80 – 0.90
S6 Package
6-Lead Plastic TSOT-23
(Reference LTC DWG # 05-08-1636)
2.90 BSC
0.62 MAX 0.95 REF
(NOTE 4)
1.22 REF
PIN ONE ID
0.80 – 0.90
0.20 BSC
0.01 – 0.10
1.00 MAX
DATUM ‘A’
16
LT1815/LT1816/LT1817
PACKAGE DESCRIPTION
S8 Package
8-Lead Plastic Small Outline (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1610)
.189 – .197
.045 ±.005 (4.801 – 5.004)
.050 BSC NOTE 3
8 7 6 5
.245
MIN .160 ±.005
.150 – .157
.228 – .244
(3.810 – 3.988)
(5.791 – 6.197)
NOTE 3
.030 ±.005
TYP
1 2 3 4
RECOMMENDED SOLDER PAD LAYOUT
.010 – .020
× 45° .053 – .069
(0.254 – 0.508)
(1.346 – 1.752)
.004 – .010
.008 – .010
0°– 8° TYP (0.101 – 0.254)
(0.203 – 0.254)
.016 – .050
.014 – .019 .050
(0.406 – 1.270)
(0.355 – 0.483) (1.270)
NOTE: TYP BSC
INCHES
1. DIMENSIONS IN
(MILLIMETERS)
2. DRAWING NOT TO SCALE
3. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm) SO8 0303
DD Package
8-Lead Plastic DFN (3mm × 3mm)
(Reference LTC DWG # 05-08-1698 Rev C)
R = 0.125 0.40 p 0.10
TYP
5 8
0.70 p0.05
4 1
0.25 p 0.05 0.200 REF 0.75 p0.05 0.25 p 0.05
0.50 0.50 BSC
BSC 2.38 p0.10
2.38 p0.05 0.00 – 0.05 BOTTOM VIEW—EXPOSED PAD
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED
NOTE:
1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-1) 5. EXPOSED PAD SHALL BE SOLDER PLATED
2. DRAWING NOT TO SCALE 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
3. ALL DIMENSIONS ARE IN MILLIMETERS ON TOP AND BOTTOM OF PACKAGE
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
181567fb
17
LT1815/LT1816/LT1817
PACKAGE DESCRIPTION
MS8 Package
8-Lead Plastic MSOP
(Reference LTC DWG # 05-08-1660 Rev F)
3.00 p 0.102
(.118 p .004) 0.52
(NOTE 3) 8 7 6 5 (.0205)
0.889 p 0.127 REF
(.035 p .005)
DETAIL “A”
0.254 3.00 p 0.102
4.90 p 0.152
5.23 (.010) (.118 p .004)
3.20 – 3.45 0o – 6o TYP (.193 p .006)
(.206) (NOTE 4)
MIN (.126 – .136)
GAUGE PLANE
0.53 p 0.152
1 2 3 4
(.021 p .006)
0.42 p 0.038 0.65
(.0165 p .0015) (.0256) 1.10 0.86
TYP BSC (.043) (.034)
DETAIL “A” MAX REF
RECOMMENDED SOLDER PAD LAYOUT 0.18
(.007)
SEATING
PLANE 0.22 – 0.38 0.1016 p 0.0508
(.009 – .015) (.004 p .002)
TYP 0.65 MSOP (MS8) 0307 REV F
(.0256) BSC
NOTE:
1. DIMENSIONS IN MILLIMETER/(INCH) 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD
2. DRAWING NOT TO SCALE FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm
FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE (.004") MAX
MS Package
10-Lead Plastic MSOP
(Reference LTC DWG # 05-08-1661 Rev E)
3.00 ± 0.102
0.889 ± 0.127 (.118 ± .004) 0.497 ± 0.076
(.035 ± .005) (NOTE 3) (.0196 ± .003)
10 9 8 7 6
REF
5.23
(.206) 3.20 – 3.45 3.00 ± 0.102
4.90 ± 0.152
MIN (.126 – .136) DETAIL “A” (.118 ± .004)
0.254 (.193 ± .006)
(NOTE 4)
(.010)
0° – 6° TYP
18
LT1815/LT1816/LT1817
PACKAGE DESCRIPTION
GN Package
16-Lead Plastic SSOP (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1641)
S Package
14-Lead Plastic Small Outline (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1610)
.337 – .344
.045 ±.005 (8.560 – 8.738)
.050 BSC NOTE 3
14 13 12 11 10 9 8
N
N
.245
MIN .160 ±.005
.228 – .244 .150 – .157
(5.791 – 6.197) (3.810 – 3.988)
NOTE 3
1 2 3 N/2 N/2
.030 ±.005
TYP RECOMMENDED SOLDER PAD LAYOUT
1 2 3 4 5 6 7
.010 – .020
× 45° .053 – .069
(0.254 – 0.508)
(1.346 – 1.752)
.008 – .010 .004 – .010
(0.203 – 0.254) 0° – 8° TYP (0.101 – 0.254)
19
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa-
tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.
LT1815/LT1816/LT1817
TYPICAL APPLICATION
Bandpass Filter with Independently Settable Gain, Q and fC 455kHz Filter Frequency Response
R1
R = 499Ω VS = ±5V
0 R1 = 499Ω VIN = 5VP-P
R RF = 511Ω DISTORTION:
+
181567 TA06a
DIFFERENTIAL
RECEIVE
SIGNAL
–
– DRIVER
1/2 LT1816
181567 TA07
+
V–
–5V
PHONE
LINE
RELATED PARTS
PART NUMBER DESCRIPTION COMMENTS
LT1363/LT1364/LT1365 Single/Dual/Quad 70MHz, 1V/ns, C-Load™ Op Amps Wide Supply Range: ±2.5V to ±15V
LT1395/LT1396/LT1397 Single/Dual/Quad 400MHz Current Feedback Amplifiers 4.6mA Supply Current, 800V/μs, 80mA Output Current
LT1806/LT1807 Single/Dual 325MHz, 140V/μs Rail-to-Rail I/O Op Amps Low Noise: 3.5nV/√Hz
LT1809/LT1810 Single/Dual 180MHz, 350V/μs Rail-to-Rail I/O Op Amps Low Distortion: 90dBc at 5MHz
LT1812/LT1813/LT1814 Single/Dual/Quad 3mA, 100MHz, 750V/μs Op Amps Low Power: 3.6mA Max at ±5V
C-Load is a trademark of Linear Technology Corporation.
181567fb