Professional Documents
Culture Documents
Created by:
Phone:
Date: 13/08/2018
Position Qty. Description
1 SP 7-51
Submersible borehole pump, suitable for pumping clean water. Can be installed vertically or horizontally. All steel
components are made in stainless steel, EN 1.4301 (AISI 304), that ensures high corrosive resistance. This pump carries
drinking water approval.
The pump is fitted with a 7.5 kW MS6000 motor with sand shield, mechanical shaft seal, water-lubricated journal bearings
and a volume compensating diaphragm. The motor is a canned type submersible motor offering good mechanical stability
and high efficiency. Suitable for temperatures up to 40 °C.
The motor is fitted with the Grundfos Tempcon sensor that, by use of powerline communication together with a MP204
control panel, enables temperature monitoring.
The motor is for direct-on-line starting (DOL).
Pump
All pump surfaces that are in contact with pumped liquids are made in stainless steel which makes them corrosion- and
wear-resistant. The corrosion diagram below shows the capabilities of the pump and motor in relation to the temperature in
Celsius (y-axis) and the concentration of chloride in ppm (x-axis).
The elastomer parts in the pump offer good wear resistance and long service intervals. The bearings are made of LSR
(Liquid Silicone Rubber), sealing rings are made of TPU (Thermoplastic Poly-Urethane) and the non-return valve is made
of NBR (Nitrile-Butadiene Rubber). The special elastomer material of the bearings offers increased resistance to sand and
other abrasive particles (from 50 to 150 mg/l).
In case the pump is used for pumping water with high content of hydrocarbons or solvents, Grundfos offers FKM rubber
parts (Fluorocarbon) which are oil and temperature-resistant up to 90 °C.
The pump is built with octagonal bearings with sand flush channels that minimise wear. As wear of the pump is inevitable,
the pump design allows for easy replacement of all internal wear parts (bearings, impeller, wear rings and seal rings) to
maintain high performance and a long lifetime.
The suction interconnector is fitted with a strainer to prevent large particles from entering the pump. The suction
interconnector is designed to comply with NEMA standards for motor mounting/dimensions.
Company name: TATA CIPTA UTAMA, PT
Created by:
Phone:
Date: 13/08/2018
Position Qty. Description
Motor
The stator is hermetically encapsulated in stainless steel and the windings are embedded in polymer compound. This
results in high mechanical stability, optimum cooling and reduces the risk of short circuits in the windings.
The shaft seal faces are ceramic/carbon. The material combination provides good dry-running resistance. Together with
the shaft seal housing, the sand shield forms a labyrinth seal, which during normal operating conditions prevents
penetration of sand particles into the shaft seal.
The motor is fitted with the Grundfos Tempcon temperature sensor device that includes a NTC-resistor which senses the
temperature. The resistor is built-in close to the winding. The temperature is converted into a high-frequency signal which is
sent via the submersible drop cable and which can be converted into a temperature reading by means of Grundfos MP204.
The MP204 is an electronic motor protection device that also monitors the supply network quality to protect the
submersible motor against supply network disturbances.
Liquid:
Pumped liquid: Water
Maximum liquid temperature: 40 °C
Max liquid t at 0.15 m/sec: 40 °C
Liquid temperature during operation: 20 °C
Density: 998.2 kg/m³
Kinematic viscosity: 1 mm2/s
Technical:
Speed for pump data: 2900 rpm
Actual calculated flow: 2.083 l/s
Resulting head of the pump: 217 m
Shaft seal for motor: CER/CARNBR
Approvals on nameplate: CE,GOST2
Curve tolerance: ISO9906:2012 3B
Motor version: T40
Materials:
Pump: Stainless steel
EN 1.4301
AISI 304
Impeller: Stainless steel
EN 1.4301
AISI 304
Motor: Stainless steel
DIN W.-Nr. 1.4301
AISI 304
Installation:
Pump outlet: Rp1 1/2
Motor diameter: 6 inch
Electrical data:
Motor type: MS6000
Rated power - P2: 7.5 kW
Power (P2) required by pump: 7.5 kW
Mains frequency: 50 Hz
Rated voltage: 3 x 380-400-415 V
Rated current: 17.8-17.2-17.2 A
Starting current: 460-510-530 %
Cos phi - power factor: 0.84-0.82-0.79
Rated speed: 2850-2870-2880 rpm
Start. method: direct-on-line
Company name: TATA CIPTA UTAMA, PT
Created by:
Phone:
Date: 13/08/2018
Position Qty. Description
Enclosure class (IEC 34-5): IP68
Insulation class (IEC 85): F
Built-in temp. transmitter: yes
Others:
Minimum efficiency index, MEI ≥: 0.70
ErP status: EuP Standalone/Prod.
Net weight: 74.7 kg
Gross weight: 120 kg
Shipping volume: 0.412 m³
Company name: TATA CIPTA UTAMA, PT
Created by:
Phone:
Date: 13/08/2018
On request SP 7-51 50 Hz
H SP 7-51, 3*400 V, 50Hz eta
[m] [%]
Q = 2.083 l/s
H = 217 m
Es = 1.0649 kWh/m³
n = 2893 rpm
Pumped liquid = Water
Liquid temperature during operation = 20 °C
Density = 998.2 kg/m³
300
250 100
200 80
150 60
100 40
50 20
8 P1
6 P2
1
P1 = 7.986 kW
P2 = 6.481 kW
0
Company name: TATA CIPTA UTAMA, PT
Created by:
Phone:
Date: 13/08/2018
H SP 7-51, 3*400 V, 50Hz eta
Description Value [m] [%]
Q = 2.083 l/s
General information: H = 217 m
Product name: SP 7-51 Es = 1.0649 kWh/m³
n = 2893 rpm
Product No: On request Pumped liquid = Water
EAN number: On request 300
Liquid temperature during operation = 20 °C
Density = 998.2 kg/m³
Technical:
Speed for pump data: 2900 rpm
Actual calculated flow: 2.083 l/s 250 100
Resulting head of the pump: 217 m
Stages: 51
200 80
Impeller reduc.: NONE
Shaft seal for motor: CER/CARNBR
Approvals on nameplate: CE,GOST2 150 60
Curve tolerance: ISO9906:2012 3B
Model: A
Valve: YES 100 40
AISI 304 6 P2
Installation: 5
Pump outlet: Rp1 1/2 4
Motor diameter: 6 inch 3
Liquid: 139.5
2
GN 139.5
Rp1 1/2
Mains frequency: 50 Hz
Rated voltage: 3 x 380-400-415 V
Rated current: 17.8-17.2-17.2 A
Starting current: 460-510-530 %
577
U1, W2 Brown
V1, U2 Black
W1, V2 Grey
Company name: TATA CIPTA UTAMA, PT
Created by:
Phone:
Date: 13/08/2018
On request SP 7-51 50 Hz
cos phi SP7-51 + MS6000 7.5 kW 3*400 V, 50 Hz I
eta [A]
cos phi
0.8 40
eta
0.6 30
0.4 20
0.2 10
P2 = 6.481 kW
cos phi = 0.79
Eta = 81.2 %
I = 14.6 A
0.0 0
0 1 2 3 4 5 6 7 8 9 10 11 12 P2 [kW]
n P1
[rpm] [kW]
3000
2800 16
n
P1
2600 12
2400 8
2200 4
P1 = 7.986 kW
n = 2893 rpm
2000 0
Company name: TATA CIPTA UTAMA, PT
Created by:
Phone:
Date: 13/08/2018
On request SP 7-51 50 Hz
Rp1 1/2
139.5 GN
2851
3428
577
139.5
Date: 13/08/2018
On request SP 7-51 50 Hz
Y DOL
L1 L2 L3 PE L1 L2 L3 PE
W2 U2 V2 U1 V1 W1
U1 V1 W1 PE PE
M M
3 3
U1, W2 Brown
V1, U2 Black
W1, V2 Grey
Date: 13/08/2018
28,000
26,000
SP 7-51
24,000 22221 EUR
100 %
22,000
20,000
18,000
16,000
14,000
70%
12,000
10,000
8,000
6,000
4,000
30% Energy cost
2,000
Initial cost
0
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0 4.2 4.4 4.6 4.8 5.0 5.2 5.4 5.6 5.8
Payback Time
40,000 Life Cycle Costs [EUR]
38,000
36,000 SP 7-51
34,000
32,000
30,000
28,000
26,000
24,000
22,000
20,000
18,000
16,000
14,000
12,000
10,000
8,000
6,000
4,000
2,000
years of operation
0
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Company name: TATA CIPTA UTAMA, PT
Created by:
Phone:
Date: 13/08/2018
Life Cycle Cost Report
Requirements: General inputs:
Flow: 2.083 l/s Energy price (high tariff): 0.15 EUR/kWh n - Life in years: 10
Capacity per year: ---- i - Interest rate: 0 %
Head: ---- p - Inflation rate: 6 %
Inputs: A:
System: SP 7-51
per year total (life)
Initial investment cost [EUR]
Pump system [EUR]
Further investment [EUR]
[EUR/Year]
Routine maintenance cost [EUR/Year]
Repair cost [EUR/Year]
Other yearly costs [EUR/Year]
Output:
Net present LCC-value [EUR] 22221