Professional Documents
Culture Documents
CUSTOMER : FOXCONN
□ APPROVED □ REJECTED
□ APPROVED
THE CONDITIONS :
Document No of
REV. Issue date Description
Specification
CMMS136E-1R0MS 00 2015.05.20 Issue of new specification.
Page 3 of 8
SPECIFICATION FOR APPROVAL
Delta Part No﹒︰CMMS136E-1R0MS Rev. ︰00
Part Name︰Molding Inductor
2. Application
DC/DC converter for CPU in Notebook PC
Thin type on-board power supply module for exchanger
VRM for server
3. Type Designation
CMMS 136E – 1R0 M S
(1) (2) (3) (4) (5)
L Code Dimensions(mm)
A' A
1
B L 13.45 0.35
W W 12.6 0.2
W B' T 6.3 0.2
A 2.0 0.5
A’ 2.5 0.1 2
B 4.0 0.5
B’ 6.0 0.2
H T
B H 0 ~ +0.15
A
Page 4 of 8
SPECIFICATION FOR APPROVAL
5. Marking and Date Code
5-1 Marking
The inductor is marked with a 3-digit code
Example – – 1.0H 1R0
1R0
5-2 Date Code
XXX
X
(1)
XX
(2)
XXX
(3)
XXX
Where (1) Year Code
Ex : 2015 = 5
(2) Weekly Code
Serial number : 01 ~ 53
(3) Taping No.
Serial number : 000 ~ ZZZ
B
A 5.0
B 8.0
A
C 14.6
C Unit : mm
Page 5 of 8
SPECIFICATION FOR APPROVAL
7. Specifications
L0 Heat Rating Current Saturation Current
Inductance Rdc ( m)
Part Number DC Amps. Idc ( A ) DC Amps. Isat ( A )
( H )
@ (0A) Typical Maximum Typical Maximum Typical Maximum
CMMS136E-1R0MS 1.0 1.8 2.15 29.0 28.0 53.0 50.0
* :If you require another part number please contact with us.
**:Inductance Tolerance 20%
Note 1.: All test data is referenced to 25℃ ambient.
Note 2.: Idc : DC current (A) that will cause an approximate △T of 40℃
Note 3.: Isat : DC current (A) that will cause L0 to drop approximately 30%
Note 4.: Operating Temperature Range -55℃ to + 125℃
Note 5.: The part temperature (ambient + temp rise) should not exceed 125℃ under the worst case operating
conditions. Circuit design, component placement, PCB trace size and thickness, airflow and other cooling
provision all affect the part temperature. Part temperature should be verified in the end application.
Note 6.: The rated current as listed is either the saturation current or the heating current depending on which value is
lower.
1.20
CMMS136E-1R0MS 100
1.00
80
INDUCTANCE(μH)
TEMP RISE(℃)
0.80
60
0.60
40
0.40
INDUCTANCE(μH)
20
0.20 TEMP RISE (℃)
0.00 0
0 5 10 15 20 25 30 35 40 45 50 55 60
DC BIAS(Amps)
Page 6 of 8
SPECIFICATION FOR APPROVAL
Test Instruments
Wayne kerr 3260B/G LCR Meter
Wayne kerr 3265B Bias Current Source
Test Condition
Temperature : 26 3℃ , Humidity : 70% RH
Frequency : 100KHz , 1.0V
8. Reliability
8-1 Mechanical
Note1 : When there are questions concerning measurement result : measurement shall be made after
48 2 hours of recovery under the standard condition
Page 8 of 8
SPECIFICATION FOR APPROVAL
9. Care note
9-1 Care note for Use
(1) Storage Condition :
Temperature 25 to 35℃, Humidity 45 to 85% RH
(3) Model :
When this power choke coil was used in a similar or new product to the original one,
sometimes it might be unable to satisfy the specifications due to difference of condition
of usage.
(4) Drop :
If the power choke coil suffered mechanical stress such as drop, characteristics may
become poor ( due to damage on coil bobbin, etc. ).
Never use such stressed power choke coil.