Professional Documents
Culture Documents
FP3.1.0
Release Upgrade Procedure
GDM-G30FP031-05-0A
The information in this document is subject to change without notice and describes only the product
defined in the introduction of this documentation. This documentation is intended for the use of
Coriant customers only for the purposes of the agreement under which the document is submitted,
and no part of it may be used, reproduced, modified or transmitted in any form or means without the
prior written permission of Coriant. The documentation has been prepared to be used by professional
and properly trained personnel, and the customer assumes full responsibility when using it. Coriant
welcomes customer comments as part of the process of continuous development and improvement of
the documentation.
The information or statements given in this documentation concerning the suitability, capacity, or
performance of the mentioned hardware or software products are given "as is" and all liability arising
in connection with such hardware or software products shall be defined conclusively and finally in a
separate agreement between Coriant and the customer. However, Coriant has made all reasonable
efforts to ensure that the instructions contained in the document are adequate and free of material
errors and omissions. Coriant will, if deemed necessary by Coriant, explain issues which may not be
covered by the document. Coriant will correct errors in this documentation as soon as possible.
IN NO EVENT WILL CORIANT BE LIABLE FOR ERRORS IN THIS DOCUMENTATION OR FOR
ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL
OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT,
REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE
FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT.
This documentation and the product it describes are considered protected by copyrights and other
intellectual property rights according to the applicable laws. Other product names mentioned in this
document may be trademarks of their respective owners, and they are mentioned for identification
purposes only.
Copyright © Coriant 2018. All rights reserved.
2/30 © Coriant
G30 FP3.1.0 Release Upgrade Procedure
Table of Contents
Table of Contents .................................................................................................................. 3
1 Purpose .......................................................................................................... 6
2 Overview ......................................................................................................... 7
2.1 Upgrade Path .................................................................................................. 7
2.2 Service interruption ......................................................................................... 7
2.3 Management interruption ................................................................................ 8
3 Preparations.................................................................................................... 9
3.1 Material requirements ..................................................................................... 9
3.2 Hardware and software Check ........................................................................ 9
3.2.1 Hardware version check .................................................................................. 9
3.2.2 Software version check ................................................................................. 12
3.3 Alarm Management ....................................................................................... 12
3.4 NE Database Backup .................................................................................... 12
3.5 Clear NE Sessions ........................................................................................ 13
© Coriant 3/30
G30 FP3.1.0 Release Upgrade Procedure
9 Fallback ........................................................................................................ 29
9.1 Switch to previous version............................................................................. 29
4/30 © Coriant
G30 FP3.1.0 Release Upgrade Procedure
Contact:
Summary of changes:
© Coriant 5/30
G30 FP3.1.0 Release Upgrade Procedure
1 Purpose
This document provides detailed guideline to carry out software upgrade of G30
from FP2.1.1 or FP3.0.3 to FP3.1.0.
6/30 © Coriant
G30 FP3.1.0 Release Upgrade Procedure
2 Overview
This document instructs the steps for upgrading the Node software from FP2.1.1
or FP3.0.3 to FP3.1.0, including the available roll back options.
All the upgrade steps for FP2.1.1 are the same as FP3.0.3.
© Coriant 7/30
G30 FP3.1.0 Release Upgrade Procedure
The traffic on card will be interrupted up to 15 minutes in the worst case during card
rebooting.
8/30 © Coriant
G30 FP3.1.0 Release Upgrade Procedure
3 Preparations
3.1 Material requirements
Before upgrade, following materials are required. (Table 3.1-1 Material
requirements)
Software Type Recommended Software
MD5 WinMD5 v1.20 or higher version
SSH client Putty 0.60 or higher version
SFTP server Core FTP mini-sftp-server V2.03 or higher version
G30 NE software G30 FP3.1.0 and FP3.0.3 or FP2.1.1 SW
New TNMS software V 17.10.0
Table 3.1-1 Material requirements
It is important that all the NEs’ hardware versions should be reviewed. Only following
hardware versions or higher are supported.
Minimum
Product Number Description
revision
GQS-G30CHASZ-00 G30 chassis A
GPS-G30PSUAC-00 G30 AC power module A
GPS-G30PSUDC-00 G30 DC power module A
GFS-G30FANZZ-00 G30 fan module A
GLS-G30CHM1Z-00 G30 CHM1 card (4x100G) A
© Coriant 9/30
G30 FP3.1.0 Release Upgrade Procedure
10/30 © Coriant
G30 FP3.1.0 Release Upgrade Procedure
© Coriant 11/30
G30 FP3.1.0 Release Upgrade Procedure
Use the following command to back up the database of the NE to the SFTP/SCP
server:
upload database sftp://username@<sftp IP address>/<filename>.zip
* For example “upload database sftp://groove@172.29.51.227/NE-Name-DBbackup-20180801.zip”
upload database scp://username@<scp IP address>/<filename>.zip
* For example “upload database scp://groove@172.29.51.227/NE-Name-DBbackup-20180801.zip”
Input the SFTP/SCP password when the prompt ‘PASSWORD:’ is on the screen.
12/30 © Coriant
G30 FP3.1.0 Release Upgrade Procedure
Check if the database file has been uploaded at the appointed folder of the
SFTP/SCP server.
© Coriant 13/30
G30 FP3.1.0 Release Upgrade Procedure
4 TNMS Upgrade
Please refer to the TNMS release notes and customer documentation for the TNMS
compatibility and upgrade on the CRM portal (http://customer.coriant.com).
14/30 © Coriant
G30 FP3.1.0 Release Upgrade Procedure
5 SW Downloading Instructions
5.1 New NE Software
The SW load of G30 FP3.1.0 can be found on the CRM (http://customer.coriant.com).
Unzip the downloaded file in same folder from CRM .Copy two files in same folder on
the SFTP server.
*Note: There are 2 files in the system software, same file name but different suffix (.dcr
and .zip). These 2 files should be saved in a same folder.
*If you can’t get the NE SW from above link, please contact your Coriant’s support team.
GROOVE_G30_3.1.0_20180731.dcr, the file size is 1,385 bytes.
MD5 checksum: 550d61cdd07042b715af92914768681c
GROOVE_G30_3.1.0_20180731.zip, the file size is 214,367,039 bytes.
MD5 checksum: b2b6f78a0334e81f343fd9ed4ad2e7b4
Table 5.1-1 FP3.1.0 NE software MD5 checksum
Before implement the software load, make sure the MD5 checksum generated by you
is the same as published in the upgrade procedure.
Input the SFTP/SCP password when the prompt ‘PASSWORD:’ is on the screen.
© Coriant 15/30
G30 FP3.1.0 Release Upgrade Procedure
16/30 © Coriant
G30 FP3.1.0 Release Upgrade Procedure
6.2 Reboot
FP2.1.1FP3.1.0 Please select either cold reboot cards separately or cold reboot NE to
finish all the upgrade process. Recommend reboot it same time on both NEs after activate
SW image in order to reduce the traffic interruption interval.
FP3.0.3FP3.1.0 Please warm reboot NE with FPGA-Upgrade and cold reboot CHM1G
card.
© Coriant 17/30
G30 FP3.1.0 Release Upgrade Procedure
18/30 © Coriant
G30 FP3.1.0 Release Upgrade Procedure
© Coriant 19/30
G30 FP3.1.0 Release Upgrade Procedure
WARNING
! Even if the database backup has been done before, please also backup the
database again to ensure it is up-to-date.
20/30 © Coriant
G30 FP3.1.0 Release Upgrade Procedure
© Coriant 21/30
G30 FP3.1.0 Release Upgrade Procedure
22/30 © Coriant
G30 FP3.1.0 Release Upgrade Procedure
7.6 Reboot
FP2.1.1FP3.1.0 Please select either cold reboot cards separately or cold reboot NE to
finish all the upgrade process. Recommend reboot it same time on both NEs after activate
the SW image in order to reduce the traffic interruption interval.
FP3.0.3FP3.1.0 Please warm reboot NE with FPGA-Upgrade and cold reboot CHM1G
card.
© Coriant 23/30
G30 FP3.1.0 Release Upgrade Procedure
24/30 © Coriant
G30 FP3.1.0 Release Upgrade Procedure
© Coriant 25/30
G30 FP3.1.0 Release Upgrade Procedure
Verity if the SW version, database version and firmware version are correct after
upgrade.
show –rt sw- management
Confirm the following items are correct after upgrade:
1. The active SW load version is ‘FP3.1.0;
2. The active database version is ‘FP3.1.0;
3. Confirmed the fw-state is all current
26/30 © Coriant
G30 FP3.1.0 Release Upgrade Procedure
© Coriant 27/30
G30 FP3.1.0 Release Upgrade Procedure
8.3 Re-connect NE
28/30 © Coriant
G30 FP3.1.0 Release Upgrade Procedure
9 Fallback
If the NE is abnormal after upgrade (For example: function problem, traffic does not
return or other unpredictable problem), please rollback the foregone release.
The NE will do cold reboot automatically. NE will loss communication from the SSH
client.
After 10 minutes, the NE can be connected again.
During fallback the traffic on the NE will interrupt for no more than 20 minutes in the
worst case.
When the NE is re-connected, use the following command to confirm the NE SW is
switched successfully.
After cold reboot completed, reconnect the NE by CLI, check the software load
information:
show –rt sw-management
Confirm the following items are correct after NE SW reboot:
1. The active database version is ‘FP3.0.3;
2. The active SW load version is ‘FP3.0.3;
© Coriant 29/30
G30 FP3.1.0 Release Upgrade Procedure
NOTICE:
If the NE cannot be recovered automatically after fallback or fw-state is not current, please
download the FP3.0.3 or FP2.1.1 software load, and switch to previous load and download
backup NE database.
30/30 © Coriant