Professional Documents
Culture Documents
33 O
2 2
6 Restrictor Y1 (simultaneously) (simultaneously) not move
3
18 ...
30V 3
6.1
6.2
Restrictor Y1 *
)
)
Check restrictor (6) and open
Restrictor Y2 *
4
5
4
5 7 Transmission ratio if necessary
4 ... 20mA
selector
6
0/4 ... 20mA
6 1 Drive actuator to working
13 8
7
8
7
8 9
Sound absorber
Adjustment wheel
range using
9 9
BE1 for slipping clutch
10 10
O
90
10 Terminals for basic
up to
Restart initialization
unit
o 4 11 Terminals for option
33
33° (simultaneously) (simultaneously)
modules Change gearing (7)
12 Plug
12 13 Cable glant Down tolerance
>5s Continue using
14 Label
(on module cover)
band violated
15 Purging air selector
6.1 6.2 or adjust sliding clutch up
11 10 9 7 8 6 5
*) With double-action actuators to display
Changing the input level Automatic initial start-up (starting with factory setting)
Mode Display Step Meaning then only
Continue using
1.)
P-manual mode Potentiometer Part-turn Linear actuator:
setting [%] actuator Once the slipping Set pick-up lever into vertical
Change position clutch has been
using position using
Not initialized
adjusted
Linear actuator
(can be reached Continue using
using preset)
PRST
Acknowledge message
Configure >5s Press for > 5 s using
Parameter
Change parameter value
2.) Up tolerance band Set the next highest travel
Remaining steps carried out automatically
name using violated value on the lever
Parameter
number Restart initialization
Change value >5s
Parameter Additionally possible with rotary
using
name actuators:
3.) Direction of action is determined
>5s >5s
Manual mode Adjust using up to
Position [%]
display:
Checking of travel and adjustment
Error code of zero and stroke
(The gray values in the top display line are examples)
Auto
10.TSUP Setpoint ramp up s 0
0 to 400
11.TSDO Setpoint ramp down 0 to 400 s 0
Setpoint function Linear Lin
Equal-percentage 1:25, 1:33, 1:50 1- 25 1 - 33 1 - 50
12.SFCT Lin
Inverse equal-percentage 1:25, 1:33, 1:50 n1 - 25 n1 - 33 n1 - 50
Freely adjustable FrEE
13.SL0 Setpoint turning point at 0% 0.0
14.SL1 5% 5.0
usw. bis 3) to 0,0 to 100,0 % etc. to
(example)
32.SL19 95% 95.0
33.SL20 100% 100.0
Auto
34.DEBA Dead zone of controller 0,1 to 10,0 % Auto
NC contact
4) OFF
42.BIN1 Block configuring and manual bLoc2
Drive valve to position up uP -uP
Drive valve to position down doWn -doWn
Block movement StoP -StoP
Function of BI 2 None OFF
4) -on
NO contact
Only message on
NC contact
43.BIN2 OFF
Drive valve to position up uP -uP
Drive valve to position down doWn -doWn
Block movement StoP -StoP
44.AFCT OFF
A1=min. A2=min
A1=max. A2=max
5)
normal
1) If "turn" is selected, you cannot set 33° 4) NC contact means: action with opened switch or Low level
2) Parameter does not appear if 1.YFCT=turn has been selected NO contact means: action with closed switch or High level
3) Turning points only appear wih selection 12.SFCT = FrEE 5) Normal means: High level without fault
Inverted means: Low level without fault