Professional Documents
Culture Documents
Sample Question Paper & Syllabus for Skill Test – 50 Marks – 2 Hours
Note: Sample questions given are only indicative in nature and not exhaustive. Level of
the questions may also vary.
Syllabus for Skill Test: Aptitude, reasoning, general knowledge, current affairs,
English, Computer knowledge, Basic mathematics & science. (Total 50 Questions: 1
mark each; Objective Type; Correct answer: 1 mark; Wrong answer: Negative marks:
0.5)
Sample Questions:
1. Ten years ago, P was half of Q's age. If the ratio of their present ages is 3:4, , what will be
the total of
their present ages?
A. 45 B. 40 C. 35 D. 30
2.The cost price of 20 articles is the same as the selling price of x articles. If the profit is
25%, find the
value of x.
A. 15 B. 25 C. 18 D. 16
3.P is able to do a piece of work in 15 days and Q can do the same work in 20 days. If they
can work
together for 4 days, what is the fraction of work left?
A. 8/15 B. 7/15 C. 11/15 D. 2/11
4. Below five words are given. Find out that word, the spelling of which is WRONG.
The letter of that word is the answer. If all the four words are spelt correctly, the answer is 'E',
i.e., "AllCorrect".
A. Appraise
B. Commend
C. Mentanence
D. Behavior
E. All correct
5.In the following the questions choose the word which best expresses the meaning of the
given word. CORPULENT
A. Lean
B. Gaunt
C. Emaciated
D. Obese
6. Look at this series: 2, 1, (1/2), (1/4), ... What number should come next?
A. (1/3)
B. (1/8)
C. (2/8)
1/8
D. (1/16)
A. First order equation; B. second order equation; C. Third order equation; D. Fourth
order equation.
2/8
Sample Paper & Syllabus for Main Written Test – 100 Marks – 3 hours
Note: Sample questions given are only indicative in nature and not exhaustive. Level of
the questions may also vary.
3/8
4. The technical term “Star- Delta” refers to
a.a. Welding
a.b. Road Sign
a.c. Piping Sign
a.d. Motor Starter
Ans:
5. What is Dall Tube?
a.a. Tube filled with Dall
a.b. Orifice meter
a.c. Venturimeter
a.d. None of the above
Ans:
a. m/s
b. m2/s
c. m3/s
d. dimensionless
2. If x and y are horizontal and vertical distances of a point in jet trajectory and g
is the acceleration due to gravity what will be the velocity of jet at venacontracta ?
a. √(2gx²/y)
b. √(gx²/2y)
c. √(2gy²/x)
d. √(gy²/2x)
4/8
3. Find the coefficient of contraction of the orifice if coefficient of discharge is
0.7 and coefficient of velocity is 0.85
a. 0.75
b. 1.01
c. 0.82
d. 0.88
4.Head loss between a length of 2m pipe of 25mm dia was found to be 2.5 cm of
mercury, what is the coefficient of friction if velocity inside the pipe is 1.3 m/s?
a. 0.049
b. 0.031
c. 0.48
5.For the same length of pipe and same discharge if the diameter is doubled, the frictional
losses will be
a. Increased by 16 times
b. Decreased by 16 times
c. Increased by 32 times
d. Decreased by 32 times
(2 Marks)
Velocimetry (PIV). It has ----- Laser system and two Cameras. It is used to measure
--turbulent flow.
7.Write the names of two flow rate (discharge) measuring equipment for flow in a pipeline
system: (2 Marks)
a)
5/8
b)
Part 4: Technical Report writing; Ledger/ Stock Inventory methods; Use of Electrical
and electronics Instruments (20 Marks) – 4 Questions
1) Letter Writing: Write a Letter to Head, Civil Engineering, through proper channel,
requesting for purchasing consumables for Fluid Mechanics Labcourse starting in
January 2018. (4 marks)
2) For a building with 10 stories, has an underground sump located 5m below the ground
level. The height of the building is 35m. There are three tanks, each 9,000 liters
capacity kept at the height given. The tanks are interconnected. The tanks are to be
filled in 30 minutes. Assume1HP = 75m-kg/sec. Make suitable assumptions if
required.
Answer the following.
6/8
(6x1= 6 Marks)
------------------
specifications:-------------------------------------
7/8