Professional Documents
Culture Documents
Draft saved
Questions
Design of pavements
Clear selection
Cement content
Aggregate Shape
Aggregate texture
Clear selection
https://docs.google.com/forms/d/e/1FAIpQLSdvIs_qyRC_sL5KNSx_nw3b_bfdB6lLw1DVpZOkEDvWf5rQeQ/formResponse 1/9
9/24/21, 12:06 PM ATAL FDP: Recent Advances in Pavement Analysis, Design and Evaluation: Evaluation Quiz
The air void content in cold mix asphalt (CMA) is generally 1 point
Same as HMA
zero
Clear selection
A subgrade soil is having CBR value of 4.8, Its Resilient modulus value will 1 point
be
30
36
42
48
Clear selection
Iron Production
Copper Production
Aluminum Production
Brick Production
Clear selection
https://docs.google.com/forms/d/e/1FAIpQLSdvIs_qyRC_sL5KNSx_nw3b_bfdB6lLw1DVpZOkEDvWf5rQeQ/formResponse 2/9
9/24/21, 12:06 PM ATAL FDP: Recent Advances in Pavement Analysis, Design and Evaluation: Evaluation Quiz
Clear selection
Empirical approach
Mechanistic approach
Mechanistic-Empirical approah
Clear selection
If asphalt binder shows the phase angle value of zero degree, It behavior 1 point
will be
Purely Elastic
Purely Plastic
Purely Viscous
Viscoelastic
Clear selection
https://docs.google.com/forms/d/e/1FAIpQLSdvIs_qyRC_sL5KNSx_nw3b_bfdB6lLw1DVpZOkEDvWf5rQeQ/formResponse 3/9
9/24/21, 12:06 PM ATAL FDP: Recent Advances in Pavement Analysis, Design and Evaluation: Evaluation Quiz
Clear selection
Which of the preventive maintenance is not suitable for moisture barrier 1 point
Fog Seal
Slurry Seal
Chip Seal
Thin surfacing
Clear selection
For rigid pavements, subgrade should have a minimum CBR value of 1 point
Clear selection
https://docs.google.com/forms/d/e/1FAIpQLSdvIs_qyRC_sL5KNSx_nw3b_bfdB6lLw1DVpZOkEDvWf5rQeQ/formResponse 4/9
9/24/21, 12:06 PM ATAL FDP: Recent Advances in Pavement Analysis, Design and Evaluation: Evaluation Quiz
Wax
Water
Oil
Polymer
Clear selection
What is designed air void content preferred for bituminous mixes 1 point
<3%
3-5%
6-8%
>8%
Clear selection
None
Clear selection
https://docs.google.com/forms/d/e/1FAIpQLSdvIs_qyRC_sL5KNSx_nw3b_bfdB6lLw1DVpZOkEDvWf5rQeQ/formResponse 5/9
9/24/21, 12:06 PM ATAL FDP: Recent Advances in Pavement Analysis, Design and Evaluation: Evaluation Quiz
Which of the soils is considered most problematic for road construction 1 point
Moorum/red soils
Alluvial soils
Dessert Soils
Clear selection
damage for Bottom up cracking (BUC) & Top down cracking (TDC) is
>1
<1
negative
Clear selection
1 MPa
0.5 MPa
0.6 MPa
0.8 MPa
Clear selection
https://docs.google.com/forms/d/e/1FAIpQLSdvIs_qyRC_sL5KNSx_nw3b_bfdB6lLw1DVpZOkEDvWf5rQeQ/formResponse 6/9
9/24/21, 12:06 PM ATAL FDP: Recent Advances in Pavement Analysis, Design and Evaluation: Evaluation Quiz
Granular subbase
Subgrade
Clear selection
Static
Dynamic
Sinusoidal
Clear selection
Consistency
Workability
Clear selection
https://docs.google.com/forms/d/e/1FAIpQLSdvIs_qyRC_sL5KNSx_nw3b_bfdB6lLw1DVpZOkEDvWf5rQeQ/formResponse 7/9
9/24/21, 12:06 PM ATAL FDP: Recent Advances in Pavement Analysis, Design and Evaluation: Evaluation Quiz
Very High
Moderate
Very low
None
Clear selection
What are the challenges associated with destructive testing methods for 1 point
pavement evaluation
Resource intensive
Interruption of traffic
All of above
Clear selection
What is the general range for mixing temperature for Warm Mix Asphalt 1 point
40°C - 60°C
60°C - 100°C
100°C - 130 °C
140 °C - 170 °C
Clear selection
https://docs.google.com/forms/d/e/1FAIpQLSdvIs_qyRC_sL5KNSx_nw3b_bfdB6lLw1DVpZOkEDvWf5rQeQ/formResponse 8/9
9/24/21, 12:06 PM ATAL FDP: Recent Advances in Pavement Analysis, Design and Evaluation: Evaluation Quiz
pavement condition
Poor
Fair
Satisfactory
Good
Clear selection
Kinematic viscosity at 60 °C
Absolute viscosity at 27 °C
Clear selection
Page 2 of 2
This form was created inside Indian Institute of Technology Jodhpur. Report Abuse
Forms
https://docs.google.com/forms/d/e/1FAIpQLSdvIs_qyRC_sL5KNSx_nw3b_bfdB6lLw1DVpZOkEDvWf5rQeQ/formResponse 9/9