Professional Documents
Culture Documents
PG 500 BDK Ap Suat
PG 500 BDK Ap Suat
2 Terminal Configuration
Pressure Indicator 1. MOUNTING panel. For effective waterproof/dustproof, the rubber packing must be securely
PG500
placed between instrument and panel without any gap. If rubber packing is
Installation Manual damaged, please contact RKC sales office or the agent. (1) Digital input terminals (2) Pressure sensor input terminals
+0.6
106.1
91.6
− Always install the noise filter on a grounded panel. Minimize the wiring distance
45 0
This instrument is protected from electric shock by reinforced insulation. 3 4 5 6 7 8 9 10
between the noise filter output and the instrument power supply terminals to achieve
Provide reinforced insulation between the wire for the input signal and the wires for the most effective noise reduction.
instrument power supply, source of power and loads.
25
− Do not connect fuses or switches to the noise filter output wiring as this will reduce the COM NO NO COM NO NO
Be sure to provide an appropriate surge control circuit respectively for the following: effectiveness of the noise filter. + −
− If input/output or signal lines within the building are longer than 30 meters. • About five seconds are required as preparation time for contact output every time the ALM1 ALM2 ALM3 ALM4
CAL
− If input/output or signal lines leave the building, regardless the length. 69.8 Terminal cover Close mounting *3
instrument is turned on. Use a delay relay when the output line is used for an external
This instrument is designed for installation in an enclosed instrumentation panel. All 7.8 60
(Optional)
92 +0.8 interlock circuit. Relay contact * Can be used when the PG500X
96 [Sold separately] 0
high-voltage connections such as power supply terminals must be enclosed in the • Power supply wiring must be twisted and have a low voltage drop. (Optional) is specified. However, disabled
1*1 if the pressure sensor does not
instrumentation panel to avoid electric shock by operating personnel. • For an instrument with 24 V power supply, supply power from a SELV circuit.
All precautions described in this manual should be taken to avoid damage to the • A suitable power supply should be considered in the end-use equipment. The power have built-in resistance for
+0.6
sensitivity adjustment.
44.8
49.2
instrument or equipment.
L 0
supply must be in compliance with a limited-energy circuits (maximum available current
48
All wiring must be in accordance with local codes and regulations. of 8 A). Input/Output Isolation:
To prevent instrument damage or failure, protect the power line and the input/output • This instrument is not furnished with a power supply switch or fuse. Therefore, if a fuse : Isolated from each other circuit blocks.
Panel thickness: 1 to 10 mm L = 48×n-3 or power supply switch is required, install close to the instrument.
lines from high currents with a protection device such as fuse, circuit breaker, etc. (When mounting multiple PG500s close together, the panel n: Number of unit (2 to 6) : Not isolated between inputs (or outputs).
Prevent metal fragments or lead wire scraps from falling inside instrument case to avoid strength should be checked to ensure proper support.) Recommended fuse rating: Rated voltage 250 V, Rated current 1 A
electric shock, fire or malfunction. *1 Case rubber packing Fuse type: Time-lag fuse Transmission output (AO)
*2 When cutting out each mounting hole through a panel for individual mounting, observe that • Use the solderless terminal appropriate to the screw size. Fig. 6 Power supply
Tighten each terminal screw to the specified torque found in the manual to avoid electric Calibration output
there is no bur or distortion along the panel cutout surface, or there is no bend on the panel Screw size: M3×7 (with 5.8×5.8 square washer) φ5.5 MAX
shock, fire or malfunction. 2
surface. If so, the water resistant characteristics may worsen. Applicable wire: Solid/twisted wire of 0.25 to 1.65 mm φ3.2 MIN φ 3.2 Pressure sensor input Alarm 1 output (ALM1)
For proper operation of this instrument, provide adequate ventilation for heat
dispensation.
*3 Remove the case rubber packing. Because of closely mounting the PG500s, protection will be Specified dimension: See Fig. 6
compromised and not meet IP66 (NEMA 4X) by close mounting. Recommended tightening torque: 0.4 N・m (4 kgf・cm) Digital input 1 (DI1) Alarm 2 output (ALM2)
Do not connect wires to unused terminals as this will interfere with proper operation of Specified solderless terminals:
the instrument. Digital input 2 (DI2) Alarm 3 output (ALM3)
1.3 Procedures of Mounting and Removing Manufactured by J.S.T MFG CO., LTD. 9.0 mm
Turn off the power supply before cleaning the instrument. Circular terminal with isolation V1.25−MS3
5.6 mm Communication Alarm 4 output (ALM4)
Do not use a volatile solvent such as paint thinner to clean the instrument. Deformation Mounting procedures
or discoloration will occur. Use a soft, dry cloth to remove stains from the instrument. If solderless terminal lugs other than those in not specified dimensions are used,
1. Prepare the panel cutout as specified in terminal screws may not be tightened. In such a case, bend each solderless Wiring example
To avoid damage to instrument display, do not rub with an abrasive material or push 1.2 Dimensions. Fig. 1 terminal lug in advance and then conduct wiring. If the terminal screw is forcibly DI1: Auto zero
front panel with a hard object. tightened, it may be damaged. Digital input DI2: Hold reset
2. Insert the instrument through the panel cutout. Our pressure sensor CZ-100P/CZ-200P
Do not connect modular connectors to telephone line. DI3: Interlock release
3. Insert the mounting bracket into the mounting Up to two solderless terminal lugs can be connected to one terminal screw.
groove of the instrument. (Fig. 1) However, in this case, reinforced insulation cannot be used.
NOTICE 4. Push the mounting bracket forward until the Caution for the terminal cover usage:
PG500 rear terminals
This manual assumes that the reader has a fundamental knowledge of the principles of bracket is firmly secured to the panel. (Fig. 2) If each solderless terminal lug touches the terminal cover, remove each 13 14 15 16 17 18 19 20 21 22 23 24
electricity, process control, computer technology and communications. projection from the terminal cover by manually bending it in front and in rear until AO +
5. Only turn one full revolution after the screw broken. Recorder
The figures, diagrams and numeric values used in this manual are only for purpose of touches the panel. (Fig. 3) −
illustration. This section illustrates the projections 25 26 27 28 29 30 31 32 33 34 35 36
6. The other mounting bracket should be to be manually removed from the
RKC is not responsible for any damage or injury that is caused as a result of using this installed the same way described in 3. to 5.
instrument, instrument failure or indirect damage. terminal cover.
1 2 3 4 5 6 7 8 9 10 11 12
RKC is not responsible for any damage and/or injury resulting from the use of Fig. 2 Fig. 3
instruments made by imitating this instrument.
ALM1 ALM2 ALM4 ALM3
Periodic maintenance is required for safe and proper operation of this instrument.
Some components have a limited service life, or characteristics that change over time. Alarmer Alarmer Alarmer Alarmer
Every effort has been made to ensure accuracy of all information contained herein. N Power supply
RKC makes no warranty expressed or implied, with respect to the accuracy of the Terminal cover
information. The information in this manual is subject to change without prior notice. (sold separately) [KFB400-58<1>] L 200 V AC