Professional Documents
Culture Documents
It which combines exceptional chemical resistance Viscosity, Physica, 2 s-1, 23°C 1000 - 1600 mPa.s 2313
and an outstanding combination of heat resistance Viscosity, Physica, 20 s-1, 23°C 500 - 600 mPa.s 2313
and flexibility. Furthermore Atlac 580 ACT has very Viscosity, Physica, 250 s-1, 23°C 370 - 430 mPa.s 2313
good handling and curing properties. Atlac 580 ACT is Water content 0 - 1000 ppm 2350
resistant to many aqueous acidic salts and alkaline Acid value, as such 4-8 mg K/g 2401
solutions. Especially against alkaline media and hot Gel time from 25 to 35°C 25.5 - 31.5 minutes 2625
water Atlac 580 ACT has an outstanding Cure time from 25°C to peak 42.5 - 52.5 minutes 2625
Curing conditions
Major applications Conditions: 100 g resin + 1,50 g Butanox M 50
Atlac 580 ACT is especially adapted to meet the TM 2999 Curing agent batchnr. Peroxide,
requirements of hand lay up and spray up Condtions Butanox M 50
applications. The resin is recommended for the
fabrication of chemical resistant equipment and Properties of the liquid resin (typical values)
Property Value Unit TM
marine applications. °C 2800
Flash point appr. 33
Stability, no init., dark, 25°C 3 months -
Principal properties
Atlac 580 ACT has excellent wet out and deaeration
properties. It produces less foam when peroxides are Properties of cast unfilled resin (typical values)
added with less air inhibition resulting in a tack free Property Value Unit TM
cured surface. Specific weight 1.11 - -
Due to its urethane incorporation, Atlac 580 ACT can Barcol hardness GYZJ 934-1 40 Barcol ASTM D2580
be thixotropised easily and shows an improved Tensile strength 83 MPa ISO 527-2
compatibility with aramid fibre reinforcements. Tensile E-modulus 3.5 GPa ISO 527-2
Atlac 580 ACT has a low exotherm in curing allowing Elongation at break 4.2 % ISO 527-2
Curing conditions
All properties are measured at 20°C unless otherwise specified.
Cure system: Atlac 580 + 0.5% NL63-10P, 0.5% NL51P and 1.5%
Butanox M-50.
All samples were cured during 24 hrs at ambient temperature,
Date of issue: February 12 Version: 001957/8.0
The user is held to check the quality, safety and other properties of the product referred to herein. The information and recommendations in
this document are to the best of our knowledge, reliable. However, no rights whatsoever can be derived from this document or the
information contained therein by any party, other than those expressly accepted by a selling entity of the Royal DSM group of companies
(“DSM Selling Entity”) in a binding sale and purchase agreement for product referred to herein. For the avoidance of doubt THE ROYAL DSM
GROUP OF COMPANIES MAKE NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR
PURPOSE. Unless explicitly agreed to otherwise in writing by the DSM Selling Entity, all offers, quotations, sales and deliveries of DSM products
are subject to the General Conditions of Sale of such DSM Selling Entity.
This document has been issued by DSM Composite Resins on behalf of the DSM Selling Entity. For more information: www.compositeresins.com
Page 1 of 2
Product Data Sheet
The user is held to check the quality, safety and other properties of the product referred to herein. The information and recommendations in
this document are to the best of our knowledge, reliable. However, no rights whatsoever can be derived from this document or the
information contained therein by any party, other than those expressly accepted by a selling entity of the Royal DSM group of companies
(“DSM Selling Entity”) in a binding sale and purchase agreement for product referred to herein. For the avoidance of doubt THE ROYAL DSM
GROUP OF COMPANIES MAKE NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR
PURPOSE. Unless explicitly agreed to otherwise in writing by the DSM Selling Entity, all offers, quotations, sales and deliveries of DSM products
are subject to the General Conditions of Sale of such DSM Selling Entity.
This document has been issued by DSM Composite Resins on behalf of the DSM Selling Entity. For more information: www.compositeresins.com
Page 2 of 2