Professional Documents
Culture Documents
Identidades Vetoriais - Plasma Formulary
Identidades Vetoriais - Plasma Formulary
A. S. Richardson
Pulsed Power Physics Branch
Plasma Physics Division
Naval Research Laboratory
Washington, DC 20375
Supported by
The Office of Naval Research
CONTENTS
Numerical and Algebraic . . . . . . . . . . . . . . . . . . . . 3
Vector Identities . . . . . . . . . . . . . . . . . . . . . . . 4
Differential Operators in Curvilinear Coordinates . . . . . . . . . 6
Dimensions and Units . . . . . . . . . . . . . . . . . . . . . 10
International System (SI) Nomenclature . . . . . . . . . . . . . 13
Metric Prefixes . . . . . . . . . . . . . . . . . . . . . . . . 13
Physical Constants (SI) . . . . . . . . . . . . . . . . . . . . . 14
Physical Constants (cgs) . . . . . . . . . . . . . . . . . . . . 16
Formula Conversion . . . . . . . . . . . . . . . . . . . . . . 18
Maxwell’s Equations . . . . . . . . . . . . . . . . . . . . . . 19
Electricity and Magnetism . . . . . . . . . . . . . . . . . . . 20
Electromagnetic Frequency/Wavelength Bands . . . . . . . . . . 21
AC Circuits . . . . . . . . . . . . . . . . . . . . . . . . . 22
Dimensionless Numbers of Fluid Mechanics . . . . . . . . . . . . 23
Shocks . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Fundamental Plasma Parameters . . . . . . . . . . . . . . . . 28
Plasma Dispersion Function . . . . . . . . . . . . . . . . . . 30
Collisions and Transport . . . . . . . . . . . . . . . . . . . . 31
Approximate Magnitudes in Some Typical Plasmas . . . . . . . . . 40
Ionospheric Parameters . . . . . . . . . . . . . . . . . . . . 42
Solar Physics Parameters . . . . . . . . . . . . . . . . . . . . 43
Thermonuclear Fusion . . . . . . . . . . . . . . . . . . . . . 44
Relativistic Electron Beams . . . . . . . . . . . . . . . . . . . 46
Beam Instabilities . . . . . . . . . . . . . . . . . . . . . . . 48
Lasers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Atomic Physics and Radiation . . . . . . . . . . . . . . . . . . 53
Atomic Spectroscopy . . . . . . . . . . . . . . . . . . . . . 59
Complex (Dusty) Plasmas . . . . . . . . . . . . . . . . . . . 62
References . . . . . . . . . . . . . . . . . . . . . . . . . . 66
2
NUMERICAL AND ALGEBRAIC
Gain in decibels of 𝑃2 relative to 𝑃1
𝐺 = 10 log10 (𝑃2 /𝑃1 ).
𝑥+𝑦 𝑥 + 𝑦 + 𝑛𝑧
= ( ).
𝑥 + 𝑦 + 𝑛𝑧 𝑛
3
VECTOR IDENTITIES4
Notation: 𝑓, 𝑔, are scalars; A, B, etc., are vectors; 𝙏 is a tensor; 𝙄 is the unit
dyad.
(1) A⋅B×C=A×B⋅C=B⋅C×A
= B×C⋅A = C⋅A×B = C×A⋅B
(2) A × (B × C) = (C × B) × A = (A ⋅ C)B − (A ⋅ B)C
(3) A × (B × C) + B × (C × A) + C × (A × B) = 0
(4) (A × B) ⋅ (C × D) = (A ⋅ C)(B ⋅ D) − (A ⋅ D)(B ⋅ C)
(5) (A × B) × (C × D) = (A × B ⋅ D)C − (A × B ⋅ C)D
(6) ∇(𝑓𝑔) = ∇(𝑔𝑓) = 𝑓∇𝑔 + 𝑔∇𝑓
(7) ∇ ⋅ (𝑓A) = 𝑓∇ ⋅ A + A ⋅ ∇𝑓
(8) ∇ × (𝑓A) = 𝑓∇ × A + ∇𝑓 × A
(9) ∇ ⋅ (A × B) = B ⋅ ∇ × A − A ⋅ ∇ × B
(10) ∇ × (A × B) = A(∇ ⋅ B) − B(∇ ⋅ A) + (B ⋅ ∇)A − (A ⋅ ∇)B
(11) A × (∇ × B) = (∇B) ⋅ A − (A ⋅ ∇)B
(12) ∇(A ⋅ B) = A × (∇ × B) + B × (∇ × A) + (A ⋅ ∇)B + (B ⋅ ∇)A
(13) ∇2 𝑓 = ∇ ⋅ ∇𝑓
(14) ∇2 A = ∇(∇ ⋅ A) − ∇ × ∇ × A
(15) ∇ × ∇𝑓 = 0
(16) ∇ ⋅ ∇ × A = 0
(28) ∫ 𝑑𝑉∇ ⋅ A = ∫ 𝑑S ⋅ A
𝑉 𝑆
(29) ∫ 𝑑𝑉∇ ⋅ 𝙏 = ∫ 𝑑S ⋅ 𝙏
𝑉 𝑆
(30) ∫ 𝑑𝑉∇ × A = ∫ 𝑑S × 𝐴
𝑉 𝑆
(32) ∫ 𝑑𝑉(A ⋅ ∇ × ∇ × B − B ⋅ ∇ × ∇ × A)
𝑉
= ∫ 𝑑S ⋅ (B × ∇ × A − A × ∇ × B)
𝑆
(33) ∫ 𝑑S × ∇𝑓 = ∮ 𝑑l𝑓
𝑆 𝐶
5
(34) ∫ 𝑑S ⋅ ∇ × A = ∮ 𝑑l ⋅ A
𝑆 𝐶
(35) ∫(𝑑S × ∇) × A = ∮ 𝑑l × A
𝑆 𝐶
6
Laplacian of a vector
2 ∂𝐴𝜙 𝐴
(∇2 A)𝑟 = ∇2 𝐴𝑟 − − 2𝑟
𝑟2 ∂𝜙 𝑟
2 2 2 ∂𝐴𝑟 𝐴𝜙
(∇ A)𝜙 = ∇ 𝐴𝜙 + 2 − 2
𝑟 ∂𝜙 𝑟
(∇2 A)𝑧 = ∇2 𝐴𝑧
Components of (A ⋅ ∇)B
∂𝐵𝑟 𝐴𝜙 ∂𝐵𝑟 ∂𝐵 𝐴𝜙 𝐵𝜙
(A ⋅ ∇B)𝑟 = 𝐴𝑟 + + 𝐴𝑧 𝑟 −
∂𝑟 𝑟 ∂𝜙 ∂𝑧 𝑟
∂𝐵𝜙 𝐴𝜙 ∂𝐵𝜙 ∂𝐵𝜙 𝐴𝜙 𝐵𝑟
(A ⋅ ∇B)𝜙 = 𝐴𝑟 + + 𝐴𝑧 +
∂𝑟 𝑟 ∂𝜙 ∂𝑧 𝑟
∂𝐵𝑧 𝐴𝜙 ∂𝐵𝑧 ∂𝐵𝑧
(A ⋅ ∇B)𝑧 = 𝐴𝑟 + + 𝐴𝑧
∂𝑟 𝑟 ∂𝜙 ∂𝑧
Divergence of a tensor
1 ∂ 1 ∂𝑇𝜙𝑟 ∂𝑇 𝑇𝜙𝜙
(∇ ⋅ 𝙏)𝑟 = (𝑟𝑇 ) + + 𝑧𝑟 −
𝑟 ∂𝑟 𝑟𝑟 𝑟 ∂𝜙 ∂𝑧 𝑟
1 ∂ 1 ∂𝑇𝜙𝜙 ∂𝑇𝑧𝜙 𝑇𝜙𝑟
(∇ ⋅ 𝙏)𝜙 = (𝑟𝑇 ) + + +
𝑟 ∂𝑟 𝑟𝜙 𝑟 ∂𝜙 ∂𝑧 𝑟
1 ∂ 1 ∂𝑇𝜙𝑧 ∂𝑇𝑧𝑧
(∇ ⋅ 𝙏)𝑧 = (𝑟𝑇 ) + +
𝑟 ∂𝑟 𝑟𝑧 𝑟 ∂𝜙 ∂𝑧
Divergence
1 ∂ 2 1 ∂ 1 ∂𝐴𝜙
∇⋅A= (𝑟 𝐴𝑟 ) + (sin 𝜃𝐴𝜃 ) +
𝑟2 ∂𝑟 𝑟 sin 𝜃 ∂𝜃 𝑟 sin 𝜃 ∂𝜙
7
Gradient
∂𝑓 1 ∂𝑓 1 ∂𝑓
(∇𝑓)𝑟 = ; (∇𝑓)𝜃 = ; (∇𝑓)𝜙 =
∂𝑟 𝑟 ∂𝜃 𝑟 sin 𝜃 ∂𝜙
Curl
1 ∂ 1 ∂𝐴𝜃
(∇ × A)𝑟 = (sin 𝜃𝐴𝜙 ) −
𝑟 sin 𝜃 ∂𝜃 𝑟 sin 𝜃 ∂𝜙
1 ∂𝐴𝑟 1 ∂
(∇ × A)𝜃 = − (𝑟𝐴𝜙 )
𝑟 sin 𝜃 ∂𝜙 𝑟 ∂𝑟
1 ∂ 1 ∂𝐴𝑟
(∇ × A)𝜙 = (𝑟𝐴𝜃 ) −
𝑟 ∂𝑟 𝑟 ∂𝜃
Laplacian
1 ∂ 2 ∂𝑓 1 ∂ ∂𝑓 1 ∂2 𝑓
∇2 𝑓 = (𝑟 )+ 2 (sin 𝜃 ) +
𝑟2 ∂𝑟 ∂𝑟 𝑟 sin 𝜃 ∂𝜃 ∂𝜃 𝑟 sin 𝜃 ∂𝜙
2 2 2
Laplacian of a vector
2𝐴𝑟 2 ∂𝐴𝜃 2 cot 𝜃𝐴𝜃 2 ∂𝐴𝜙
(∇2 A)𝑟 = ∇2 𝐴𝑟 − − 2 − − 2
𝑟2 𝑟 ∂𝜃 𝑟2 𝑟 sin 𝜃 ∂𝜙
2 ∂𝐴𝑟 𝐴𝜃 2 cos 𝜃 ∂𝐴𝜙
(∇2 A)𝜃 = ∇2 𝐴𝜃 + 2 − −
𝑟 ∂𝜃 𝑟2 sin 𝜃 𝑟2 sin 𝜃 ∂𝜙
2 2
Components of (A ⋅ ∇)B
∂𝐵𝑟 𝐴 ∂𝐵 𝐴𝜙 ∂𝐵𝑟 𝐴𝜃 𝐵𝜃 + 𝐴𝜙 𝐵𝜙
(A ⋅ ∇B)𝑟 = 𝐴𝑟 + 𝜃 𝑟 + −
∂𝑟 𝑟 ∂𝜃 𝑟 sin 𝜃 ∂𝜙 𝑟
∂𝐵𝜃 𝐴𝜃 ∂𝐵𝜃 𝐴𝜙 ∂𝐵𝜃 𝐴𝜃 𝐵𝑟 cot 𝜃𝐴𝜙 𝐵𝜙
(A ⋅ ∇B)𝜃 = 𝐴𝑟 + + + −
∂𝑟 𝑟 ∂𝜃 𝑟 sin 𝜃 ∂𝜙 𝑟 𝑟
∂𝐵𝜙 𝐴𝜃 ∂𝐵𝜙 𝐴𝜙 ∂𝐵𝜙 𝐴𝜙 𝐵𝑟 cot 𝜃𝐴𝜙 𝐵𝜃
(A ⋅ ∇B)𝜙 = 𝐴𝑟 + + + +
∂𝑟 𝑟 ∂𝜃 𝑟 sin 𝜃 ∂𝜙 𝑟 𝑟
Divergence of a tensor
1 ∂ 2 1 ∂
(∇ ⋅ 𝙏)𝑟 = (𝑟 𝑇𝑟𝑟 ) + (sin 𝜃𝑇𝜃𝑟 )
𝑟2 ∂𝑟 𝑟 sin 𝜃 ∂𝜃
1 ∂𝑇𝜙𝑟 𝑇𝜃𝜃 + 𝑇𝜙𝜙
+ −
𝑟 sin 𝜃 ∂𝜙 𝑟
8
1 ∂ 2 1 ∂
(∇ ⋅ 𝙏)𝜃 = (𝑟 𝑇𝑟𝜃 ) + (sin 𝜃𝑇𝜃𝜃 )
𝑟2 ∂𝑟 𝑟 sin 𝜃 ∂𝜃
1 ∂𝑇𝜙𝜃 𝑇 cot 𝜃𝑇𝜙𝜙
+ + 𝜃𝑟 −
𝑟 sin 𝜃 ∂𝜙 𝑟 𝑟
1 ∂ 2 1 ∂
(∇ ⋅ 𝙏)𝜙 = (𝑟 𝑇𝑟𝜙 ) + (sin 𝜃𝑇𝜃𝜙 )
𝑟2 ∂𝑟 𝑟 sin 𝜃 ∂𝜃
1 ∂𝑇𝜙𝜙 𝑇𝜙𝑟 cot 𝜃𝑇𝜙𝜃
+ + +
𝑟 sin 𝜃 ∂𝜙 𝑟 𝑟
9
DIMENSIONS AND UNITS
To get the value of a quantity in Gaussian units, multiply the value expressed
in SI units by the conversion factor. Multiples of 3 in the conversion factors
result from approximating the speed of light 𝑐 = 2.9979 × 1010 cm/sec ≈
3 × 1010 cm/sec.
Capaci- 𝑡2 𝑞2
𝐶 ℓ farad 9 × 1011 cm
tance 𝑚ℓ2
𝑚1/2 ℓ3/2
Charge 𝑞 𝑞 coulomb 3 × 109 statcoulomb
𝑡
Charge 𝑞 𝑚1/2 coulomb statcoulomb
𝜌 3 × 103
density ℓ3 ℓ3/2 𝑡 /m3 /cm3
Conduc- 2
𝑡𝑞 ℓ
siemens 9 × 1011 cm/sec
tance 𝑚ℓ2 𝑡
Conduc- 𝑡𝑞2 1
𝜎 siemens /m 9 × 109 sec−1
tivity 𝑚ℓ3 𝑡
𝑞 𝑚1/2 ℓ3/2
Current 𝐼, 𝑖 ampere 3 × 109 statampere
𝑡 𝑡2
Current 𝑞 𝑚1/2 statampere
J, j ampere /m2 3 × 105
density ℓ2 𝑡 ℓ1/2 𝑡2 /cm2
𝑚 𝑚
Density 𝜌 kg/m3 10−3 g/cm3
ℓ3 ℓ3
Displace- 𝑞 𝑚1/2 coulomb statcoulomb
D 12𝜋 × 105
ment ℓ2 ℓ1/2 𝑡 /m2 /cm2
Electric 𝑚ℓ 𝑚1/2 1
E volt/m × 10−4 statvolt/cm
field 𝑡2 𝑞 ℓ1/2 𝑡 3
Electro- ℰ, 𝑚ℓ2 𝑚1/2 ℓ1/2 1
volt × 10−2 statvolt
motance Emf 𝑡2 𝑞 𝑡 3
𝑚ℓ2 𝑚ℓ2
Energy 𝑈, 𝑊 joule 107 erg
𝑡2 𝑡2
Energy 𝑚 𝑚
𝑤, 𝜖 joule/m3 10 erg/cm3
Density ℓ𝑡2 ℓ𝑡2
10
Physical Sym- Dimensions Conversion Gaussian
SI Units
Quantitiy bol SI Gaussian Factor Units
𝑚ℓ 𝑚ℓ
Force F newton 105 dyne
𝑡2 𝑡2
1 1
Frequency 𝑓, 𝜈 hertz 1 hertz
𝑡 𝑡
𝑚ℓ2 𝑡 1
Impedance 𝑍 ohm × 10−11 sec/cm
𝑡𝑞2 ℓ 9
𝑚ℓ2 𝑡2 1
Inductance 𝐿 henry × 10−11 sec2 /cm
𝑞2 ℓ 9
centimeter
Length ℓ ℓ ℓ meter (m) 102
(cm)
Magnetic 𝑞 𝑚1/2 ampere–
H 4𝜋 × 10−3 oersted
intensity ℓ𝑡 ℓ1/2 𝑡 turn/m
Magnetic 𝑚ℓ2 𝑚1/2 ℓ3/2
Φ weber 108 maxwell
flux 𝑡𝑞 𝑡
Magnetic 𝑚 𝑚1/2
B tesla 104 gauss
induction 𝑡𝑞 ℓ1/2 𝑡
Magnetic 𝑙2 𝑞 𝑚1/2 𝑙5/2
𝑚, 𝜇 ampere–m2 103 oersted–cm3
moment 𝑡 𝑡
Magnet- 𝑞 𝑚1/2 ampere–
M 4𝜋 × 10−3 oersted
ization ℓ𝑡 ℓ1/2 𝑡 turn/m
Magneto- ℳ, 𝑞 𝑚1/2 ℓ1/2 ampere– 4𝜋
gilbert
motance Mmf 𝑡 𝑡2 turn 10
kilogram
Mass 𝑚, 𝑀 𝑚 𝑚 103 gram (g)
(kg)
𝑚ℓ 𝑚ℓ
Momentum p, P kg–m/s 105 g–cm/sec
𝑡 𝑡
Momentum 𝑚 𝑚
kg/m2 –s 10−1 g/cm2 –sec
density ℓ2 𝑡 ℓ2 𝑡
𝑚ℓ 1
Permeability 𝜇 1 henry/m × 107 —
𝑞2 4𝜋
11
Physical Sym- Dimensions Conversion Gaussian
SI Units
Quantitiy bol SI Gaussian Factor Units
𝑡2 𝑞2
Permittivity 𝜖 1 farad/m 36𝜋 × 109 —
𝑚ℓ3
𝑞 𝑚1/2 coulomb statcoulomb
Polarization P 3 × 105
ℓ 2 ℓ1/2 𝑡 /m2 /cm2
𝑚ℓ2 𝑚1/2 ℓ1/2 1
Potential 𝑉, 𝜙 volt × 10−2 statvolt
𝑡2 𝑞 𝑡 3
𝑚ℓ2 𝑚ℓ2
Power 𝑃 watt 107 erg/sec
𝑡3 𝑡3
Power 𝑚 𝑚
watt/m3 10 erg/cm3 –sec
density ℓ𝑡3 ℓ𝑡3
𝑚 𝑚
Pressure 𝑝, 𝑃 pascal 10 dyne/cm2
ℓ𝑡2 ℓ𝑡2
𝑞2 1 ampere–
Reluctance ℛ 4𝜋 × 10−9 cm−1
𝑚ℓ2 ℓ turn /weber
𝑚ℓ2 𝑡 1
Resistance 𝑅 ohm × 10−11 sec/cm
𝑡𝑞2 ℓ 9
𝑚ℓ3 1
Resistivity 𝜂, 𝜌 𝑡 ohm–m × 10−9 sec
𝑡𝑞2 9
Thermal
𝑚ℓ 𝑚ℓ watt/m–deg erg/cm–sec–
conduc- 𝜅, 𝑘 105
𝑡3 𝑡3 (K) deg (K)
tivity
Time 𝑡 𝑡 𝑡 second (s) 1 second (sec)
Vector 𝑚ℓ 𝑚1/2 ℓ1/2
A weber/m 106 gauss–cm
potential 𝑡𝑞 𝑡
ℓ ℓ
Velocity v m/s 102 cm/sec
𝑡 𝑡
𝑚 𝑚
Viscosity 𝜂, 𝜇 kg/m–s 10 poise
ℓ𝑡 ℓ𝑡
1 1
Vorticity 𝜁 s−1 1 sec−1
𝑡 𝑡
𝑚ℓ2 𝑚ℓ2
Work 𝑊 joule 107 erg
𝑡2 𝑡2
12
INTERNATIONAL SYSTEM (SI) NOMENCLATURE6
Physical Name Symbol Name Symbol
Physical Quantity
Quantity of Unit for Unit of Unit for Unit
*length meter m electric resistance ohm Ω
*mass kilogram kg electric
siemens S
*time second s conductance
*current ampere A electric
farad F
*temperature kelvin K capacitance
*amount of magnetic flux weber Wb
mole mol magnetic
substance henry H
*luminous inductance
candela cd magnetic intensity tesla T
intensity
†plane angle radian rad luminous flux lumen lm
†solid angle steradian sr illuminance lux lx
frequency hertz Hz ‡activity (of a
energy joule J radioactive becquerel Bq
force newton N source)
pressure pascal Pa §absorbed dose (of
power watt W ionizing gray Gy
radiation)
electric
coulomb C
charge ‡Common non-SI unit is curie (Ci):
electric 1 Ci = 3.7 × 1010 Bq
volt V 1 Bq = 1 decay per sec
potential
§Common non-SI unit is rad:
*SI base unit †Supplementary unit 100 rad = 1 Gy = 1 J / kG
METRIC PREFIXES
Multiple Prefix Symbol Multiple Prefix Symbol
−1
10 deci d 10 deca da
10−2 centi c 102 hecto h
10−3 milli m 103 kilo k
10−6 micro μ 106 mega M
10−9 nano n 109 giga G
10−12 pico p 1012 tera T
10−15 femto f 1015 peta P
10−18 atto a 1018 exa E
13
PHYSICAL CONSTANTS (SI)7
14
Physical Quantitiy Symbol Value Units
5
Wave number associated 𝑘0 = 𝑒/ℎ𝑐 8.0655 × 10 m−1
with 1 eV
Energy associated with ℎ𝜈0 1.6022 × 10−19 J
with 1 eV
Energy associated with ℎ𝑐 1.9864 × 10−25 J
1 m−1
Energy associated with 𝑚𝑒3 /8𝜖0 2 ℎ2 13.606 eV
1 Rydberg
Energy associated with 𝑘/𝑒 8.6174 × 10−5 eV
1 Kelvin
Temperature associated 𝑒/𝑘 1.1604 × 104 K
with 1 eV
Avogadro number 𝑁𝐴 6.0221 × 1023 mol−1
Faraday constant 𝐹 = 𝑁𝐴 𝑒 9.6485 × 104 C mol−1
Gas constant 𝑅 = 𝑁𝐴 𝑘 8.3145 J K−1 mol−1
Loschmidt’s number 𝑛0 2.6868 × 1025 m−3
(no. density at STP)
Atomic mass unit 𝑚ᵆ 1.6605 × 10−27 kg
Standard temperature 𝑇0 273.15 K
Atmospheric pressure 𝑝0 = 𝑛0 𝑘𝑇0 1.0133 × 105 Pa
Pressure of 1 mm Hg 1.3332 × 102 Pa
(1 torr)
Molar volume at STP 𝑉0 = 𝑅𝑇0 /𝑝0 2.2414 × 10−2 m3
Molar weight of air 𝑀air 2.8971 × 10−2 kg
calorie (cal) 4.1868 J
Gravitational acceleration 𝑔 9.8067 m s−2
15
PHYSICAL CONSTANTS (CGS)7
16
Physical Quantitiy Symbol Value Units
3
Wave number associated 𝑘0 8.0655 × 10 cm−1
with 1 eV
Energy associated with 1.6022 × 10−12 erg
1 eV
Energy associated with 1.9864 × 10−16 erg
1 cm−1
Energy associated with 13.606 eV
1 Rydberg
Energy associated with 8.6174 × 10−5 eV
1 deg Kelvin
Temperature associated 1.1604 × 104 deg (K)
with 1 eV
Avogadro number 𝑁𝐴 6.0221 × 1023 mol−1
Faraday constant 𝐹 = 𝑁𝐴 𝑒 2.8925 × 1014 statcoul/mol
Gas constant 𝑅 = 𝑁𝐴 𝑘 8.3145 × 107 erg/deg-
mol
Loschmidt’s number 𝑛0 2.6868 × 1019 cm−3
(no. density at STP)
Atomic mass unit 𝑚ᵆ 1.6605 × 10−24 g
Standard temperature 𝑇0 273.15 deg (K)
Atmospheric pressure 𝑝0 = 𝑛0 𝑘𝑇0 1.0133 × 106 dyne/cm2
Pressure of 1 mm Hg 1.3332 × 103 dyne/cm2
(1 torr)
Molar volume at STP 𝑉0 = 𝑅𝑇0 /𝑝0 2.2414 × 104 cm3
Molar weight of air 𝑀air 28.971 g
calorie (cal) 4.1868 × 107 erg
Gravitational acceleration 𝑔 980.67 cm/sec2
17
FORMULA CONVERSION8
Here 𝛼 = 10 cm m , 𝛽 = 107 erg J−1 , 𝜖0 = 8.8542 × 10−12 F m−1 , 𝜇0 = 4𝜋 ×
2 −1
10−7 H m−1 , 𝑐 = (𝜖0 𝜇0 )−1/2 = 2.9979 × 108 m s−1 , and ℏ = 1.0546 × 10−34 J s.
To derive a dimensionally correct SI formula from one expressed in Gaussian
units, substitute for each quantity according to 𝑄̄ = 𝑘𝑄, ̄ where 𝑘 ̄ is the co-
efficient in the second column of the table corresponding to 𝑄 (overbars de-
note variables expressed in Gaussian units). Thus, the formula 𝑎0̄ = ℏ2̄ /𝑚̄ 𝑒2̄
for the Bohr radius becomes 𝛼𝑎0 = (ℏ𝛽)2 /[(𝑚𝛽/𝛼2 ) (𝑒2 𝛼𝛽/4𝜋𝜖0 )], or 𝑎0 =
𝜖0 ℎ2 /𝜋𝑚𝑒2 . To go from SI to natural units in which ℏ = 𝑐 = 1 (distinguished
by a circumflex), use 𝑄 = 𝑘−1 ̂ 𝑄,̂ where 𝑘 ̂ is the coefficient corresponding to
𝑄 in the third column. Thus 𝑎0̂ = 4𝜋𝜖0 ℏ2 /[(𝑚ℏ/𝑐)(̂ 𝑒2̂ 𝜖0 ℏ𝑐)] = 4𝜋/𝑚̂ 𝑒2̂ . (In
transforming from SI units, do not substitute for 𝜖0 , 𝜇0 , or 𝑐.)
Physical Quantity Gaussian Units to SI Natural Units to SI
Capacitance 𝛼/4𝜋𝜖0 𝜖0 −1
Charge (𝛼𝛽/4𝜋𝜖0 )1/2 (𝜖0 ℏ𝑐)−1/2
Charge density (𝛽/4𝜋𝛼5 𝜖0 )1/2 (𝜖0 ℏ𝑐)−1/2
Current (𝛼𝛽/4𝜋𝜖0 )1/2 (𝜇0 /ℏ𝑐)1/2
Current density (𝛽/4𝜋𝛼3 𝜖0 )1/2 (𝜇0 /ℏ𝑐)1/2
Electric field (4𝜋𝛽𝜖0 /𝛼3 )1/2 (𝜖0 /ℏ𝑐)1/2
Electric potential (4𝜋𝛽𝜖0 /𝛼)1/2 (𝜖0 /ℏ𝑐)1/2
Electric conductivity (4𝜋𝜖0 )−1 𝜖0 −1
Energy 𝛽 (ℏ𝑐)−1
Energy density 𝛽/𝛼3 (ℏ𝑐)−1
Force 𝛽/𝛼 (ℏ𝑐)−1
Frequency 1 𝑐−1
Inductance 4𝜋𝜖0 /𝛼 𝜇0 −1
Length 𝛼 1
Magnetic induction (4𝜋𝛽/𝛼3 𝜇0 )1/2 (𝜇0 ℏ𝑐)−1/2
Magnetic intensity (4𝜋𝜇0 𝛽/𝛼3 )1/2 (𝜇0 /ℏ𝑐)1/2
Mass 𝛽/𝛼2 𝑐/ℏ
Momentum 𝛽/𝛼 ℏ−1
Power 𝛽 (ℏ𝑐2 )−1
Pressure 𝛽/𝛼3 (ℏ𝑐)−1
Resistance 4𝜋𝜖0 /𝛼 (𝜖0 /𝜇0 )1/2
Time 1 𝑐
Velocity 𝛼 𝑐−1
18
MAXWELL’S EQUATIONS
19
ELECTRICITY AND MAGNETISM
In the following, 𝜖 = dielectric permittivity, 𝜇 = permeability of conductor,
𝜇′ = permeability of surrounding medium, 𝜎 = conductivity, 𝑓 = 𝜔/2𝜋 =
radiation frequency, 𝜅𝑚 = 𝜇/𝜇0 and 𝜅𝑒 = 𝜖/𝜖0 . Where subscripts are used,
‘1’ denotes a conducting medium and ‘2’ a propagating (lossless dielectric)
medium. All units are SI unless otherwise specified.
Permittivity of free space 𝜖0 = 8.8542 × 10−12 F m−1
𝜇0 = 4𝜋 × 10−7 H m−1
Permeability of free space
= 1.2566 × 10−6 H m−1
Resistance of free space 𝑅0 = (𝜇0 /𝜖0 )1/2 = 376.73 Ω
Capacity of parallel plates of area 𝐴, 𝐶 = 𝜖𝐴/𝑑
separated by distance 𝑑
Capacity of concentric cylinders of 𝐶 = 2𝜋𝜖𝑙/ ln(𝑏/𝑎)
length 𝑙, radii 𝑎, 𝑏
Capacity of concentric spheres of 𝐶 = 4𝜋𝜖𝑎𝑏/(𝑏 − 𝑎)
radii 𝑎, 𝑏
Self-inductance of wire of length 𝑙, 𝐿 = 𝜇𝑙/8𝜋
carrying uniform current
Mutual inductance of parallel wires 𝐿 = (𝜇′ 𝑙/4𝜋) [1 + 4 ln(𝑑/𝑎)]
of length 𝑙, radius 𝑎, separated by
distance 𝑑
Inductance of circular loop of radius 𝐿 = 𝑏 {𝜇′ [ln(8𝑏/𝑎) − 2] + 𝜇/4}
𝑏, made of wire of radius 𝑎, carrying
uniform current
Relaxation time in a lossy medium 𝜏 = 𝜖/𝜎
Skin depth in a lossy medium 𝛿 = (2/𝜔𝜇𝜎)1/2 = (𝜋𝑓𝜇𝜎)−1/2
1/2
Wave impedance in a lossy medium 𝑍 = [𝜇/(𝜖 + 𝑖𝜎/𝜔)]
Transmission coefficient at 𝑇 = 4.22 × 10 (𝑓𝜅𝑚1 𝜅𝑒2 /𝜎)1/2
−4
20
ELECTROMAGNETIC FREQUENCY/WAVELENGTH BANDS10
21
AC CIRCUITS
For a resistance 𝑅, inductance 𝐿, and capacitance 𝐶 in series with a voltage
source 𝑉 = 𝑉0 exp(𝑖𝜔𝑡) (here 𝑖 = √−1), the current is given by 𝐼 = 𝑑𝑞/𝑑𝑡,
where 𝑞 satisfies
𝑑2 𝑞 𝑑𝑞 𝑞
𝐿 +𝑅 + = 𝑉.
𝑑𝑡2 𝑑𝑡 𝐶
Solutions are 𝑞(𝑡) = 𝑞𝑠 + 𝑞𝑡 , 𝐼(𝑡) = 𝐼𝑠 + 𝐼𝑡 , where the steady state is 𝐼𝑠 =
𝑖𝜔𝑞𝑠 = 𝑉/𝑍 in terms of the impedance 𝑍 = 𝑅 + 𝑖(𝜔𝐿 − 1/𝜔𝐶) and 𝐼𝑡 = 𝑑𝑞𝑡 /𝑑𝑡.
For initial conditions 𝑞(0) ≡ 𝑞0 = 𝑞0̄ + 𝑞𝑠 , 𝐼(0) ≡ 𝐼0 , the transients can be of
three types, depending on Δ = 𝑅2 − 4𝐿/𝐶:
(a) Overdamped, Δ > 0.
𝐼 + 𝛾+ 𝑞0̄ 𝐼 + 𝛾− 𝑞0̄
𝑞𝑡 = 0 exp(−𝛾− 𝑡) − 0 exp(−𝛾+ 𝑡),
𝛾+ − 𝛾− 𝛾+ − 𝛾−
𝛾 (𝐼 + 𝛾− 𝑞0̄ ) 𝛾 (𝐼 + 𝛾+ 𝑞0̄ )
𝐼𝑡 = + 0 exp(−𝛾+ 𝑡) − − 0 exp(−𝛾− 𝑡).
𝛾+ − 𝛾− 𝛾+ − 𝛾−
22
DIMENSIONLESS NUMBERS OF FLUID MECHANICS12
Name(s) Symbol Definition Significance
Alfvén, Kármán Al, Ka 𝑉𝐴 /𝑉 *(Magnetic force/
inertial force)1/2
Bond Bd (𝜌′ − 𝜌)𝐿2 𝑔/Σ Gravitational force/
surface tension
Boussinesq B 𝑉/(2𝑔𝑅)1/2 (Inertial force/
gravitational force)1/2
Brinkman Br 𝜇𝑉 2 /𝑘Δ𝑇 Viscous heat/conducted heat
Capillary Cp 𝜇𝑉/Σ Viscous force/surface tension
Carnot Ca (𝑇2 − 𝑇1 )/𝑇2 Theoretical Carnot cycle efficiency
Cauchy, Hooke Cy, Hk 𝜌𝑉 2 /Γ = M2 Inertial force/compressibility force
Chandrasekhar Ch 𝐵 2 𝐿2 /𝜌𝜈𝜂 Magnetic force/dissipative forces
Clausius Cl 𝐿𝑉 3 𝜌/𝑘Δ𝑇 Kinetic energy flow rate/heat
conduction rate
2
Cowling C (𝑉𝐴 /𝑉)2 = Al Magnetic force/inertial force
Crispation Cr 𝜇𝜅/Σ𝐿 Effect of diffusion/effect of surface
tension
Dean D 𝐷3/2 𝑉/𝜈(2𝑟)1/2 Transverse flow due to
curvature/longitudinal flow
Drag coefficient 𝐶𝐷 (𝜌′ − 𝜌)𝐿𝑔/ Drag force/inertial force
𝜌′ 𝑉 2
Eckert E 𝑉 2 /𝑐𝑝 Δ𝑇 Kinetic energy/change in thermal
energy
Ekman Ek (𝜈/2Ω𝐿2 )1/2 = (Viscous force/Coriolis force)1/2
(Ro/Re)1/2
Euler Eu Δ𝑝/𝜌𝑉 2 Pressure drop due to
friction/dynamic pressure
Froude Fr 𝑉/(𝑔𝐿)1/2 †(Inertial force/gravitational or
𝑉/𝑁𝐿 buoyancy force)1/2
Gay–Lussac Ga 1/𝛽Δ𝑇 Inverse of relative change in
volume during heating
Grashof Gr 𝑔𝐿3 𝛽Δ𝑇/𝜈2 Buoyancy force/viscous force
Hall coefficient 𝐶𝐻 𝜆/𝑟𝐿 Gyrofrequency/collision frequency
Hartmann H 𝐵𝐿/(𝜇𝜂)1/2 = (Magnetic force/dissipative
(Rm Re C)1/2 force)1/2
Knudsen Kn 𝜆/𝐿 Hydrodynamic time/collision time
*(†) Also defined as the inverse (square) of the quantity shown.
23
Name(s) Symbol Definition Significance
Lewis Le 𝜅/𝒟 *Thermal conduction/molecular
diffusion
Lorentz Lo 𝑉/𝑐 Magnitude of relativistic effects
Lundquist Lu 𝜇0 𝐿𝑉𝐴 /𝜂 = 𝐉 × 𝐁 force/resistive magnetic
Al Rm diffusion force
Mach M 𝑉/𝐶𝑆 Magnitude of compressibility
effects
Magnetic Mach Mm 𝑉/𝑉𝐴 = Al−1 (Inertial force/magnetic force)1/2
Magnetic Rm 𝜇0 𝐿𝑉/𝜂 Flow velocity/magnetic diffusion
Reynolds velocity
Newton Nt 𝐹/𝜌𝐿2 𝑉 2 Imposed force/inertial force
Nusselt N 𝛼𝐿/𝑘 Total heat transfer/thermal
conduction
Péclet Pe 𝐿𝑉/𝜅 Heat convection/heat conduction
Poisseuille Po 𝐷2 Δ𝑝/𝜇𝐿𝑉 Pressure force/viscous force
Prandtl Pr 𝜈/𝜅 Momentum diffusion/heat
diffusion
Rayleigh Ra 𝑔𝐻 3 𝛽Δ𝑇/𝜈𝜅 Buoyancy force/diffusion force
Reynolds Re 𝐿𝑉/𝜈 Inertial force/viscous force
Richardson Ri (𝑁𝐻/Δ𝑉)2 Buoyancy effects/vertical shear
effects
Rossby Ro 𝑉/2Ω𝐿 sin Λ Inertial force/Coriolis force
Schmidt Sc 𝜈/𝒟 Momentum diffusion/molecular
diffusion
Stanton St 𝛼/𝜌𝑐𝑝 𝑉 Thermal conduction loss/heat
capacity
Stefan Sf 𝜎𝐿𝑇 3 /𝑘 Radiated heat/conducted heat
Stokes S 𝜈/𝐿2 𝑓 Viscous damping rate/vibration
frequency
Strouhal Sr 𝑓𝐿/𝑉 Vibration speed/flow velocity
Taylor Ta (2Ω𝐿2 /𝜈)2 Centrifugal force/viscous force
𝑅1/2 (Δ𝑅)3/2 (Centrifugal force/viscous force)1/2
⋅(Ω/𝜈)
Thring, Th, Bo 𝜌𝑐𝑝 𝑉/𝜖𝜎𝑇 3 Convective heat transport/radiative
Boltzmann heat transport
Weber W 𝜌𝐿𝑉 2 /Σ Inertial force/surface tension
24
Nomenclature:
𝐵 Magnetic induction
𝐶𝑠 , 𝑐 Speeds of sound, light
𝑐𝑝 Specific heat at constant pressure (units m2 s−2 K−1 )
𝐷 = 2𝑅 Pipe diameter
𝐹 Imposed force
𝑓 Vibration frequency
𝑔 Gravitational acceleration
𝐻, 𝐿 Vertical, horizontal length scales
𝑘 = 𝜌𝑐𝑝 𝜅 Thermal conductivity (units kg m−1 s−2 )
𝑁 = (𝑔/𝐻)1/2 Brunt–Väisälä frequency
𝑅 Radius of pipe or channel
𝑟 Radius of curvature of pipe or channel
𝑟𝐿 Larmor radius
𝑇 Temperature
𝑉 Characteristic flow velocity
𝑉𝐴 = 𝐵/(𝜇0 𝜌)1/2 Alfvén speed
∂𝑇
𝛼 Newton’s-law heat coefficient, 𝑘 = 𝛼Δ𝑇
∂𝑥
𝛽 Volumetric expansion coefficient, 𝑑𝑉/𝑉 = 𝛽𝑑𝑇
Γ Bulk modulus (units kg m−1 s−2 )
Δ𝑅, Δ𝑉, Δ𝑝, Δ𝑇 Imposed differences in two radii, velocities,
pressures, or temperatures
𝜖 Surface emissivity
𝜂 Electrical resistivity
𝜅, 𝒟 Thermal, molecular diffusivities (units m2 s−1 )
Λ Latitude of point on earth’s surface
𝜆 Collisional mean free path
𝜇 = 𝜌𝜈 Viscosity
𝜇0 Permeability of free space
𝜈 Kinematic viscosity (units m2 s−1 )
𝜌 Mass density of fluid medium
𝜌′ Mass density of bubble, droplet, or moving object
Σ Surface tension (units kg s−2 )
𝜎 Stefan–Boltzmann constant
Ω Solid-body rotational angular velocity
25
SHOCKS
At a shock front propagating in a magnetized fluid at an angle 𝜃 with respect
to the magnetic induction 𝐁, the jump conditions are 13,14
(1) 𝜌𝑈 = 𝜌𝑈 ̄ ̄ ≡ 𝑞;
(2) 𝜌𝑈 2 + 𝑝 + 𝐵⟂2 /2𝜇 = 𝜌𝑈 ̄ ̄ 2 + 𝑝 ̄ + 𝐵⟂̄ 2 /2𝜇;
(3) 𝜌𝑈𝑉 − 𝐵∥ 𝐵⟂ /𝜇 = 𝜌𝑈 ̄ ̄ 𝑉 ̄ − 𝐵∥̄ 𝐵⟂̄ /𝜇;
(4) 𝐵∥ = 𝐵∥̄ ;
(5) 𝑈𝐵⟂ − 𝑉𝐵∥ = 𝑈̄ 𝐵⟂̄ − 𝑉 ̄ 𝐵∥̄ ;
1 2
(6) (𝑈 + 𝑉 2 ) + 𝑤 + (𝑈𝐵⟂2 − 𝑉𝐵∥ 𝐵⟂ )/𝜇𝜌𝑈
2
1
= (𝑈̄ 2 + 𝑉 ̄ 2 ) + 𝑤̄ + (𝑈̄ 𝐵⟂̄ 2 − 𝑉 ̄ 𝐵∥̄ 𝐵⟂̄ )/𝜇𝜌𝑈.
̄ ̄
2
Here 𝑈 and 𝑉 are components of the fluid velocity normal and tangential to
the front in the shock frame; 𝜌 = 1/𝜐 is the mass density; 𝑝 is the pressure;
𝐵⟂ = 𝐵 sin 𝜃, 𝐵∥ = 𝐵 cos 𝜃; 𝜇 is the magnetic permeability (𝜇 = 4𝜋 in cgs
units); and the specific enthalpy is 𝑤 = 𝑒 + 𝑝𝜐, where the specific internal
energy 𝑒 satisfies 𝑑𝑒 = 𝑇𝑑𝑠 − 𝑝𝑑𝜐 in terms of the temperature 𝑇 and the
specific entropy 𝑠. Quantities in the region behind (downstream from) the
front are distinguished by a bar. If 𝐵 = 0, then15
1/2
(7) 𝑈 − 𝑈̄ = [(𝑝 ̄ − 𝑝)(𝜐 − 𝜐)]̄ ;
−1 2
(8) (𝑝 ̄ − 𝑝)(𝜐 − 𝜐)̄ =𝑞 ;
1
(9) 𝑤̄ − 𝑤 = (𝑝 ̄ − 𝑝)(𝜐 + 𝜐); ̄
2
1
̄
(10) 𝑒 ̄ − 𝑒 = (𝑝 ̄ + 𝑝)(𝜐 − 𝜐).
2
In what follows we assume that the fluid is a perfect gas with adiabatic index
𝛾 = 1 + 2/𝑛, where 𝑛 is the number of degrees of freedom. Then 𝑝 = 𝜌𝑅𝑇/𝑚,
where 𝑅 is the universal gas constant and 𝑚 is the molar weight; the sound
2
speed is given by 𝐶𝑠 = (∂𝑝/∂𝜌)𝑠 = 𝛾𝑝𝜐; and 𝑤 = 𝛾𝑒 = 𝛾𝑝𝜐/(𝛾 − 1). For a
general oblique shock in a perfect gas the quantity 𝑋 = 𝑟−1 (𝑈/𝑉𝐴 )2 satisfies14
2
(11) (𝑋 − 𝛽/𝛼)(𝑋 − cos2 𝜃)2 = 𝑋 sin 𝜃 {[1 + (𝑟 − 1)/2𝛼] 𝑋 − cos2 𝜃} ,
1 2
̄ 𝛼 = [𝛾 + 1 − (𝛾 − 1)𝑟], and 𝛽 = 𝐶𝑠 /𝑉𝐴 2 = 4𝜋𝛾𝑝/𝐵 2 .
where 𝑟 = 𝜌/𝜌,
2
The density ratio is bounded by
(12) 1 < 𝑟 < (𝛾 + 1)/(𝛾 − 1).
If the shock is normal to 𝐁 (i.e., if 𝜃 = 𝜋/2), then
2
(13) 𝑈 2 = (𝑟/𝛼) {𝐶𝑠 + 𝑉𝐴 2 [1 + (1 − 𝛾/2)(𝑟 − 1)]} ;
26
(14) 𝑈/𝑈̄ = 𝐵/𝐵 ̄ = 𝑟;
(15) 𝑉 ̄ = 𝑉;
(16) 𝑝 ̄ = 𝑝 + (1 − 𝑟−1 )𝜌𝑈 2 + (1 − 𝑟2 )𝐵 2 /2𝜇.
If 𝜃 = 0, there are two possibilities: switch-on shocks, which require 𝛽 < 1
and for which
(17) 𝑈 2 = 𝑟𝑉𝐴 2 ;
(18) 𝑈̄ = 𝑉𝐴 2 /𝑈;
(19) 𝐵⟂̄ 2 = 2𝐵∥ 2 (𝑟 − 1)(𝛼 − 𝛽);
(20) 𝑉 ̄ = 𝑈̄ 𝐵⟂̄ /𝐵∥ ;
(21) 𝑝 ̄ = 𝑝 + 𝜌𝑈 2 (1 − 𝛼 + 𝛽)(1 − 𝑟−1 ),
and acoustic (hydrodynamic) shocks, for which
2
(22) 𝑈 2 = (𝑟/𝛼)𝐶𝑠 ;
(23) 𝑈̄ = 𝑈/𝑟;
(24) 𝑉 ̄ = 𝐵⟂̄ = 0;
(25) 𝑝 ̄ = 𝑝 + 𝜌𝑈 2 (1 − 𝑟−1 ).
For acoustic shocks the specific volume and pressure are related by
̄ = [(𝛾 + 1)𝑝 + (𝛾 − 1)𝑝]̄ / [(𝛾 − 1)𝑝 + (𝛾 + 1)𝑝]̄ .
(26) 𝜐/𝜐
In terms of the upstream Mach number 𝑀 = 𝑈/𝐶𝑠 ,
(27) ̄ = 𝜐/𝜐 ̄ = 𝑈/𝑈̄ = (𝛾 + 1)𝑀 2 /[(𝛾 − 1)𝑀 2 + 2];
𝜌/𝜌
(28) ̄ = (2𝛾𝑀 2 − 𝛾 + 1)/(𝛾 + 1);
𝑝/𝑝
(29) 𝑇/𝑇̄ = [(𝛾 − 1)𝑀 2 + 2](2𝛾𝑀 2 − 𝛾 + 1)/(𝛾 + 1)2 𝑀 2 ;
(30) 𝑀̄ 2 = [(𝛾 − 1)𝑀 2 + 2]/[2𝛾𝑀 2 − 𝛾 + 1].
The entropy change across the shock is
(31) Δ𝑠 ≡ 𝑠 ̄ − 𝑠 = 𝑐𝜐 ln[(𝑝/𝑝)(𝜌/
̄ 𝜌)̄ 𝛾 ],
where 𝑐𝜐 = 𝑅/(𝛾 − 1)𝑚 is the specific heat at constant volume; here 𝑅 is the
gas constant. In the weak-shock limit (𝑀 → 1),
2𝛾(𝛾 − 1) 2 16𝛾𝑅
(32) Δ𝑠 → 𝑐𝜐 (𝑀 − 1)3 ≈ (𝑀 − 1)3 .
3(𝛾 + 1) 3(𝛾 + 1)𝑚
The radius at time 𝑡 of a strong spherical blast wave resulting from the explo-
sive release of energy 𝐸 in a medium with uniform density 𝜌 is
(33) 𝑅𝑆 = 𝐶0 (𝐸𝑡2 /𝜌)1/5 ,
where 𝐶0 is a constant depending on 𝛾. For 𝛾 = 7/5, 𝐶0 = 1.033.
27
FUNDAMENTAL PLASMA PARAMETERS
All quantities are in Gaussian cgs units except temperature (𝑇, 𝑇𝑒 , 𝑇𝑖 ) ex-
pressed in eV and ion mass (𝑚𝑖 ) expressed in units of the proton mass, 𝜇 =
𝑚𝑖 /𝑚𝑝 ; 𝑍 is charge state; 𝑘 is Boltzmann’s constant; 𝐾 is wavenumber; 𝛾 is
the adiabatic index; ln Λ is the Coulomb logarithm.
Frequencies
electron gyrofrequency 𝑓𝑐𝑒 = 𝜔𝑐𝑒 /2𝜋 = 2.80 × 106 𝐵 Hz
𝜔𝑐𝑒 = 𝑒𝐵/𝑚𝑒 𝑐 = 1.76 × 107 𝐵 rad/sec
ion gyrofrequency 𝑓𝑐𝑖 = 𝜔𝑐𝑖 /2𝜋 = 1.52 × 103 𝑍𝜇−1 𝐵 Hz
𝜔𝑐𝑖 = 𝑍𝑒𝐵/𝑚𝑖 𝑐 = 9.58 × 103 𝑍𝜇−1 𝐵 rad/sec
electron plasma frequency 𝑓𝑝𝑒 = 𝜔𝑝𝑒 /2𝜋 = 8.98 × 103 𝑛𝑒 1/2 Hz
𝜔𝑝𝑒 = (4𝜋𝑛𝑒 𝑒2 /𝑚𝑒 )1/2
= 5.64 × 104 𝑛𝑒 1/2 rad/sec
ion plasma frequency 𝑓𝑝𝑖 = 𝜔𝑝𝑖 /2𝜋
= 2.10 × 102 𝑍𝜇−1/2 𝑛𝑖 1/2 Hz
𝜔𝑝𝑖 = (4𝜋𝑛𝑖 𝑍 2 𝑒2 /𝑚𝑖 )1/2
= 1.32 × 103 𝑍𝜇−1/2 𝑛𝑖 1/2 rad/sec
electron trapping rate 𝜈𝑇𝑒 = (𝑒𝐾𝐸/𝑚𝑒 )1/2
= 7.26 × 108 𝐾 1/2 𝐸 1/2 sec−1
ion trapping rate 𝜈𝑇𝑖 = (𝑍𝑒𝐾𝐸/𝑚𝑖 )1/2
= 1.69 × 107 𝑍 1/2 𝐾 1/2 𝐸 1/2 𝜇−1/2 sec−1
electron collision rate 𝜈𝑒 = 2.91 × 10−6 𝑛𝑒 ln Λ𝑇𝑒 −3/2 sec−1
ion collision rate 𝜈𝑖 = 4.80 × 10−8 𝑍 4 𝜇−1/2 𝑛𝑖 ln Λ𝑇𝑖 −3/2 sec−1
Lengths
electron deBroglie length ƛ = ℏ/(𝑚𝑒 𝑘𝑇𝑒 )1/2 = 2.76 × 10−8 𝑇𝑒 −1/2 cm
classical distance of 𝑒2 /𝑘𝑇 = 1.44 × 10−7 𝑇 −1 cm
minimum approach
electron gyroradius 𝑟𝑒 = 𝑣𝑇𝑒 /𝜔𝑐𝑒 = 2.38𝑇𝑒 1/2 𝐵−1 cm
ion gyroradius 𝑟𝑖 = 𝑣𝑇𝑖 /𝜔𝑐𝑖
= 1.02 × 102 𝜇1/2 𝑍 −1 𝑇𝑖 1/2 𝐵 −1 cm
electron inertial length 𝑐/𝜔𝑝𝑒 = 5.31 × 105 𝑛𝑒 −1/2 cm
ion inertial length 𝑐/𝜔𝑝𝑖 = 2.28 × 107 𝑍 −1 (𝜇/𝑛𝑖 )1/2 cm
Debye length 𝜆𝐷 = (𝑘𝑇/4𝜋𝑛𝑒2 )1/2 = 7.43 × 102 𝑇 1/2 𝑛−1/2 cm
magnetic Debye length 𝜆𝑀 = 𝐵/4𝜋𝑛𝑒 𝑒 = 1.66 × 108 𝐵𝑛−1 𝑒 cm
28
Velocities
electron thermal velocity 𝑣𝑇𝑒 = (𝑘𝑇𝑒 /𝑚𝑒 )1/2
= 4.19 × 107 𝑇𝑒 1/2 cm/sec
ion thermal velocity 𝑣𝑇𝑖 = (𝑘𝑇𝑖 /𝑚𝑖 )1/2
= 9.79 × 105 𝜇−1/2 𝑇𝑖 1/2 cm/sec
ion sound velocity 𝐶𝑠 = (𝛾𝑍𝑘𝑇𝑒 /𝑚𝑖 )1/2
= 9.79 × 105 (𝛾𝑍𝑇𝑒 /𝜇)1/2 cm/sec
Alfvén velocity 𝑣𝐴 = 𝐵/(4𝜋𝑛𝑖 𝑚𝑖 )1/2
= 2.18 × 1011 𝜇−1/2 𝑛𝑖 −1/2 𝐵 cm/sec
Dimensionless
(electron/proton mass ratio)1/2 (𝑚𝑒 /𝑚𝑝 )1/2 = 2.33 × 10−2 = 1/42.9
3
number of particles in (4𝜋/3)𝑛𝜆𝐷 = 1.72 × 109 𝑇 3/2 𝑛−1/2
Debye sphere
Alfvén velocity/speed of light 𝑣𝐴 /𝑐 = 7.28𝜇−1/2 𝑛𝑖 −1/2 𝐵
electron plasma/gyrofrequency 𝜔𝑝𝑒 /𝜔𝑐𝑒 = 3.21 × 10−3 𝑛𝑒 1/2 𝐵−1
ratio
ion plasma/gyrofrequency ratio 𝜔𝑝𝑖 /𝜔𝑐𝑖 = 0.137𝜇1/2 𝑛𝑖 1/2 𝐵−1
thermal/magnetic energy ratio 𝛽 = 8𝜋𝑛𝑘𝑇/𝐵 2 = 4.03 × 10−11 𝑛𝑇𝐵 −2
magnetic/ion rest energy ratio 𝐵2 /8𝜋𝑛𝑖 𝑚𝑖 𝑐2 = 26.5𝜇−1 𝑛𝑖 −1 𝐵2
Miscellaneous
Bohm diffusion coefficient 𝐷𝐵 = (𝑐𝑘𝑇/16𝑒𝐵)
= 6.25 × 106 𝑇𝐵 −1 cm2 /sec
transverse Spitzer resistivity 𝜂⟂ = 1.15 × 10−14 𝑍 ln Λ𝑇 −3/2 sec
= 1.03 × 10−2 𝑍 ln Λ𝑇 −3/2 Ω cm
The anomalous collision rate due to low-frequency ion-sound turbulence is
˜/𝑘𝑇 = 5.64 × 104 𝑛𝑒 1/2 𝑊
𝜈* ≈ 𝜔𝑝𝑒 𝑊 ˜/𝑘𝑇 sec−1 ,
˜ is the total energy of waves with 𝜔/𝐾 < 𝑣𝑇𝑖 .
where 𝑊
Magnetic pressure is given by
2
𝑃mag = 𝐵 2 /8𝜋 = 3.98 × 106 (𝐵/𝐵0 )2 dynes/cm = 3.93(𝐵/𝐵0 )2 atm,
where 𝐵0 = 10 kG = 1 T.
Detonation energy of 1 kiloton of high explosive is
𝑊kT = 1012 cal = 4.2 × 1019 erg = 4.2 × 1012 J.
29
PLASMA DISPERSION FUNCTION
16
Definition (first form valid only for Im 𝜁 > 0):
+∞ 𝑖𝜁
𝑑𝑡 exp (−𝑡2 )
𝑍(𝜁) = 𝜋−1/2 ∫ = 2𝑖 exp (−𝜁2 ) ∫ 𝑑𝑡 exp (−𝑡2 ) .
−∞
𝑡−𝜁 −∞
Physically, 𝜁 = 𝑥 + 𝑖𝑦 is the ratio of wave phase velocity to thermal velocity.
Differential equation:
𝑑𝑍 𝑑2 𝑍 𝑑𝑍
= −2 (1 + 𝜁𝑍) , 𝑍(0) = 𝑖𝜋1/2 ; + 2𝜁 + 2𝑍 = 0.
𝑑𝜁 𝑑𝜁2 𝑑𝜁
Real argument (𝑦 = 0):
𝑥
𝑍(𝑥) = exp (−𝑥2 ) (𝑖𝜋1/2 − 2 ∫ 𝑑𝑡 exp (𝑡2 )) .
0
Imaginary argument (𝑥 = 0):
𝑍(𝑖𝑦) = 𝑖𝜋1/2 exp (𝑦2 ) [1 − erf(𝑦)] .
Power series (small argument):
𝑍(𝜁) = 𝑖𝜋1/2 exp (−𝜁2 ) − 2𝜁 (1 − 2𝜁2 /3 + 4𝜁4 /15 − 8𝜁6 /105 + ⋯) .
Asymptotic series, |𝜁| ≫ 1 (Ref. 17):
𝑍(𝜁) = 𝑖𝜋1/2 𝜎 exp (−𝜁2 ) − 𝜁−1 (1 + 1/2𝜁2 + 3/4𝜁4 + 15/8𝜁6 + ⋯) ,
where 𝑦 > |𝑥|−1
⎧ 0,
𝜎= 1, |𝑦| < |𝑥|−1
⎨
⎩ 2, 𝑦 < −|𝑥|−1
Symmetry properties (the asterisk denotes complex conjugation):
𝑍(𝜁*) = − [𝑍(−𝜁)]*;
𝑍(𝜁*) = [𝑍(𝜁)] * + 2𝑖𝜋1/2 exp[−(𝜁*)2 ], (𝑦 > 0).
18
Two-pole approximations (good for 𝜁 in upper half plane except when 𝑦 <
𝜋1/2 𝑥2 exp(−𝑥2 ), 𝑥 ≫ 1):
0.50 + 0.81𝑖 0.50 − 0.81𝑖
𝑍(𝜁) ≈ − , 𝑎 = 0.51 − 0.81𝑖;
𝑎−𝜁 𝑎* + 𝜁
0.50 + 0.96𝑖 0.50 − 0.96𝑖
𝑍 ′ (𝜁) ≈ + , 𝑏 = 0.48 − 0.91𝑖.
(𝑏 − 𝜁)2 (𝑏* + 𝜁)2
30
COLLISIONS AND TRANSPORT
Temperatures are in eV; the corresponding value of Boltzmann’s constant is 𝑘 = 1.60 ×
10−12 erg/eV; masses 𝜇, 𝜇′ are in units of the proton mass; 𝑒𝛼 = 𝑍𝛼 𝑒 is the charge of species
𝛼. All other units are cgs except where noted.
Relaxation Rates
Rates are associated with four relaxation processes arising from the interac-
tion of test particles (labeled 𝛼) streaming with velocity v𝛼 through a back-
ground of field particles (labeled 𝛽):
𝑑v𝛼 𝛼\𝛽
slowing down = −𝜈𝑠 v𝛼
𝑑𝑡
𝑑 𝛼\𝛽
transverse diffusion (v − v̄ 𝛼 )2⟂ = 𝜈⟂ 𝑣𝛼 2
𝑑𝑡 𝛼
𝑑 𝛼\𝛽
parallel diffusion (v − v̄ 𝛼 )2∥ = 𝜈∥ 𝑣𝛼 2
𝑑𝑡 𝛼
𝑑 2 𝛼\𝛽
energy loss 𝑣 = −𝜈𝜖 𝑣𝛼 2 ,
𝑑𝑡 𝛼
where 𝑣𝛼 = |𝐯𝛼 | and the averages are performed over an ensemble of test
particles and a Maxwellian field particle distribution. The exact formulas
may be written19
𝛼\𝛽 𝛼\𝛽
𝜈𝑠 = (1 + 𝑚𝛼 /𝑚𝛽 )𝜓(𝑥𝛼\𝛽 )𝜈0 ;
𝛼\𝛽 𝛼\𝛽
𝜈⟂ = 2 [(1 − 1/2𝑥𝛼\𝛽 )𝜓(𝑥𝛼\𝛽 ) + 𝜓′ (𝑥𝛼\𝛽 )] 𝜈0 ;
𝛼\𝛽 𝛼\𝛽
𝜈∥ = [𝜓(𝑥𝛼\𝛽 )/𝑥𝛼\𝛽 ] 𝜈0 ;
𝛼\𝛽 𝛼\𝛽
𝜈𝜖 = 2 [(𝑚𝛼 /𝑚𝛽 )𝜓(𝑥𝛼\𝛽 ) − 𝜓′ (𝑥𝛼\𝛽 )] 𝜈0 ,
where
𝛼\𝛽
𝜈0 = 4𝜋𝑒𝛼 2 𝑒𝛽 2 𝜆𝛼𝛽 𝑛𝛽 /𝑚𝛼 2 𝑣𝛼 3 ; 𝑥𝛼\𝛽 = 𝑚𝛽 𝑣𝛼 2 /2𝑘𝑇𝛽 ;
𝑥
2 𝑑𝜓
𝜓(𝑥) = ∫ 𝑑𝑡 𝑡1/2 𝑒−𝑡 ; 𝜓′ (𝑥) = ,
√𝜋 0
𝑑𝑥
and 𝜆𝛼𝛽 = ln Λ𝛼𝛽 is the Coulomb logarithm (see below). Limiting forms of
𝜈𝑠 , 𝜈⟂ and 𝜈∥ are given in the following table. All the expressions shown have
units cm3 sec−1 . Test particle energy 𝜖 and field particle temperature 𝑇 are
both in eV; 𝜇 = 𝑚𝑖 /𝑚𝑝 where 𝑚𝑝 is the proton mass; 𝑍 is ion charge state; in
electron–electron and ion–ion encounters, field particle quantities are distin-
guished by a prime. The two expressions given below for each rate hold for
31
very slow (𝑥𝛼\𝛽 ≪ 1) and very fast (𝑥𝛼\𝛽 ≫ 1) test particles, respectively.
Slow Fast
Electron–electron
𝑒|𝑒
𝜈𝑠 /𝑛𝑒 𝜆𝑒𝑒 ≈ 5.8 × 10−6 𝑇 −3/2 ⟶ 7.7 × 10−6 𝜖−3/2
𝑒|𝑒
𝜈⟂ /𝑛𝑒 𝜆𝑒𝑒 ≈ 5.8 × 10−6 𝑇 −1/2 𝜖−1 ⟶ 7.7 × 10−6 𝜖−3/2
𝑒|𝑒
𝜈∥ /𝑛𝑒 𝜆𝑒𝑒 ≈ 2.9 × 10−6 𝑇 −1/2 𝜖−1 ⟶ 3.9 × 10−6 𝑇𝜖−5/2
Electron–ion
𝑒|𝑖
𝜈𝑠 /𝑛𝑖 𝑍 2 𝜆𝑒𝑖 ≈ 0.23𝜇3/2 𝑇 −3/2 ⟶ 3.9 × 10−6 𝜖−3/2
𝑒|𝑖 2 −4 1/2 −1/2 −1
𝜈⟂ /𝑛𝑖 𝑍 𝜆𝑒𝑖 ≈ 2.5 × 10 𝜇 𝑇 𝜖 ⟶ 7.7 × 10−6 𝜖−3/2
𝑒|𝑖
𝜈∥ /𝑛𝑖 𝑍 2 𝜆𝑒𝑖 ≈ 1.2 × 10−4 𝜇1/2 𝑇 −1/2 𝜖−1 ⟶ 2.1 × 10−9 𝜇−1 𝑇𝜖−5/2
Ion–electron
𝑖|𝑒
𝜈𝑠 /𝑛𝑒 𝑍 2 𝜆𝑖𝑒 ≈ 1.6 × 10−9 𝜇−1 𝑇 −3/2 ⟶ 1.7 × 10−4 𝜇1/2 𝜖−3/2
𝑖|𝑒 2 −9 −1 −1/2 −1
𝜈⟂ /𝑛𝑒 𝑍 𝜆𝑖𝑒 ≈ 3.2 × 10 𝜇 𝑇 𝜖 ⟶ 1.8 × 10−7 𝜇−1/2 𝜖−3/2
𝑖|𝑒 2 −9 −1 −1/2 −1
𝜈∥ /𝑛𝑒 𝑍 𝜆𝑖𝑒 ≈ 1.6 × 10 𝜇 𝑇 𝜖 ⟶ 1.7 × 10−4 𝜇1/2 𝑇𝜖−5/2
Ion–ion
𝑖|𝑖′
𝜈𝑠 𝜇′1/2 𝜇′
2 ′2
≈ 6.8 × 10−8 (1 + ) 𝑇 −3/2
𝑛𝑖′ 𝑍 𝑍 𝜆𝑖𝑖′ 𝜇 𝜇
1 1 𝜇1/2
⟶ 9.0 × 10−8 ( + ′ ) 3/2
𝜇 𝜇 𝜖
𝑖|𝑖′
𝜈⟂
≈ 1.4 × 10−7 𝜇′1/2 𝜇−1 𝑇 −1/2 𝜖−1
𝑛𝑖′ 𝑍 2 𝑍 ′2 𝜆𝑖𝑖′
⟶ 1.8 × 10−7 𝜇−1/2 𝜖−3/2
𝑖|𝑖′
𝜈∥
≈ 6.8 × 10−8 𝜇′1/2 𝜇−1 𝑇 −1/2 𝜖−1
𝑛𝑖′ 𝑍 2 𝑍 ′2 𝜆𝑖𝑖′
⟶ 9.0 × 10−8 𝜇1/2 𝜇′−1 𝑇𝜖−5/2
In the same limits, the energy transfer rate follows from the identity
𝜈𝜖 = 2𝜈𝑠 − 𝜈⟂ − 𝜈∥ ,
except for the case of fast electrons or fast ions scattered by ions, where the
leading terms cancel. Then the appropriate forms are
𝑒|𝑖
𝜈𝜖 ⟶ 4.2 × 10−9 𝑛𝑖 𝑍 2 𝜆𝑒𝑖
[𝜖−3/2 𝜇−1 − 8.9 × 104 (𝜇/𝑇)1/2 𝜖−1 exp(−1836𝜇𝜖/𝑇)] sec−1
32
and
𝑖|𝑖′ ′
𝜈𝜖 ⟶ 1.8 × 10−7 𝑛𝑖′ 𝑍 2 𝑍 ′2 𝜆𝑖𝑖′ {𝜖−3/2 𝜇1/2 /𝜇
−1.1[(𝜇 + 𝜇′ )/𝜇𝜇′ ](𝜇′ /𝑇 ′ )1/2 𝜖−1 exp(−𝜇′ 𝜖/𝜇𝑇 ′ )} sec−1 .
𝛼\𝛽
In general, the energy transfer rate 𝜈𝜖 is positive for 𝜖 > 𝜖𝛼∗ and negative for
𝜖 < 𝜖𝛼∗ , where 𝑥∗ = (𝑚𝛽 /𝑚𝛼 )𝜖𝛼∗ /𝑇𝛽 is the solution of 𝜓′ (𝑥∗ ) = (𝑚𝛼 |𝑚𝛽 )𝜓(𝑥∗ ).
The ratio 𝜖𝛼∗ /𝑇𝛽 is given for a number of specific 𝛼, 𝛽 in the following table:
𝜖𝛼∗ /𝑇𝛽 : 1.5 0.98 4.8 × 10−3 2.6 × 10−3 1.8 × 10−3 1.4 × 10−3
When both species are near Maxwellian, with 𝑇𝑖 ≲ 𝑇𝑒 , there are just two
characteristic collision rates. For 𝑍 = 1,
𝜈𝑒 = 2.9 × 10−6 𝑛𝜆𝑇𝑒 −3/2 sec−1 ;
𝜈𝑖 = 4.8 × 10−8 𝑛𝜆𝑇𝑖 −3/2 𝜇−1/2 sec−1 .
Temperature Isotropization
Isotropization is described by
𝑑𝑇⟂ 1 𝑑𝑇∥
=− = −𝜈𝑇𝛼 (𝑇⟂ − 𝑇∥ ),
𝑑𝑡 2 𝑑𝑡
where, if 𝐴 ≡ 𝑇⟂ /𝑇∥ − 1 > 0,
2√𝜋𝑒𝛼2 𝑒𝛽2 𝑛𝛼 𝜆𝛼𝛽 tan−1 (𝐴1/2 )
𝜈𝑇𝛼 = 𝐴−2 [−3 + (𝐴 + 3) ].
𝑚1/2
𝛼 (𝑘𝑇∥ )
3/2 𝐴1/2
−1
If 𝐴 < 0, tan−1 (𝐴1/2 )/𝐴1/2 is replaced by tanh (−𝐴)1/2 /(−𝐴)1/2 .
For 𝑇⟂ ≈ 𝑇∥ ≡ 𝑇,
𝜈𝑇𝑒 = 8.2 × 10−7 𝑛𝜆𝑇 −3/2 sec−1 ;
𝜈𝑇𝑖 = 1.9 × 10−8 𝑛𝜆𝑍 2 𝜇−1/2 𝑇 −3/2 sec−1 .
Thermal Equilibration
If the components of a plasma have different temperatures, but no relative
drift, equilibration is described by
𝑑𝑇𝛼 𝛼\𝛽
= ∑ 𝜈𝜖̄ (𝑇𝛽 − 𝑇𝛼 ),
𝑑𝑡 𝛽
33
where
𝛼\𝛽
(𝑚𝛼 𝑚𝛽 )1/2 𝑍𝛼2 𝑍𝛽2 𝑛𝛽 𝜆𝛼𝛽
𝜈𝜖̄ = 1.8 × 10−19 sec−1 .
(𝑚𝛼 𝑇𝛽 + 𝑚𝛽 𝑇𝛼 )3/2
For electrons and ions with 𝑇𝑒 ≈ 𝑇𝑖 ≡ 𝑇, this implies
𝑒|𝑖 𝑖|𝑒
𝜈𝜖̄ /𝑛𝑖 = 𝜈𝜖̄ /𝑛𝑒 = 3.2 × 10−9 𝑍 2 𝜆/𝜇𝑇 3/2 cm3 sec−1 .
Coulomb Logarithm
For test particles of mass 𝑚𝛼 and charge 𝑒𝛼 = 𝑍𝛼 𝑒 scattering off field par-
ticles of mass 𝑚𝛽 and charge 𝑒𝛽 = 𝑍𝛽 𝑒, the Coulomb logarithm is defined
as 𝜆 = ln Λ ≡ ln(𝑟max /𝑟min ). Here 𝑟min is the larger of 𝑒𝛼 𝑒𝛽 /𝑚𝛼𝛽 𝑢̄2 and
ℏ/2𝑚𝛼𝛽 𝑢,̄ averaged over both particle velocity distributions, where 𝑚𝛼𝛽 =
𝑚𝛼 𝑚𝛽 /(𝑚𝛼 + 𝑚𝛽 ) and 𝐮 = 𝐯𝛼 − 𝐯𝛽 ; 𝑟max = (4𝜋 ∑ 𝑛𝛾 𝑒𝛾2 /𝑘𝑇𝛾 )−1/2 , where
2
the summation extends over all species 𝛾 for which 𝑢̄2 < 𝑣𝑇𝛾 = 𝑘𝑇𝛾 /𝑚𝛾 . If
−1 −1
this inequality cannot be satisfied, or if either 𝑢𝜔
̄ 𝑐𝛼 < 𝑟max or 𝑢𝜔
̄ 𝑐𝛽 < 𝑟max ,
the theory breaks down. Typically 𝜆 ≈ 10–20. Corrections to the transport co-
efficients are 𝑂(𝜆−1 ); hence the theory is good only to ∼ 10% and fails when
𝜆 ∼ 1.
The following cases are of particular interest:
(a) Thermal electron–electron collisions
𝜆𝑒𝑒 = 23.5 − ln(𝑛1/2
𝑒 𝑇𝑒
−5/4
) − [10−5 + (ln 𝑇𝑒 − 2)2 /16]1/2 .
(b) Electron–ion collisions
1/2 −3/2
⎧ 23 − ln (𝑛𝑒 𝑍𝑇𝑒 ) , 𝑇𝑖 𝑚𝑒 /𝑚𝑖 < 𝑇𝑒 < 10𝑍 2 eV;
1/2 −1
𝜆𝑒𝑖 = 𝜆𝑖𝑒 = 24 − ln (𝑛𝑒 𝑇𝑒 ) , 𝑇𝑖 𝑚𝑒 /𝑚𝑖 < 10𝑍 2 eV < 𝑇𝑒 ;
⎨ 1/2 −3/2 2
⎩ 16 − ln (𝑛𝑖 𝑇𝑖 𝑍 𝜇) , 𝑇𝑒 < 𝑇𝑖 𝑚𝑒 /𝑚𝑖 .
(c) Mixed ion–ion collisions
2 1/2
𝑍𝑍 ′ (𝜇 + 𝜇′ ) 𝑛𝑖 𝑍 2 𝑛 ′ 𝑍′
𝜆𝑖𝑖′ = 𝜆𝑖′ 𝑖 = 23 − ln [ ′
( + 𝑖 ) ].
𝜇𝑇𝑖′ + 𝜇 𝑇𝑖 𝑇𝑖 𝑇𝑖′
34
Fokker-Planck Equation
𝑒𝛼2 𝑒𝛽2
𝐉𝛼\𝛽 = 2𝜋𝜆𝛼𝛽 ∫ 𝑑3𝑣′ (𝑢2 𝙄 − 𝐮𝐮)𝑢−3
𝑚𝛼
1 𝛼 1 𝛽 ′
⋅{ 𝑓 (𝐯)∇𝐯′ 𝑓𝛽 (𝐯′ ) − 𝑓 (𝐯 )∇𝐯 𝑓𝛼 (𝐯)} ,
𝑚𝛽 𝑚𝛼
(Landau form) where 𝐮 = 𝐯′ − 𝐯 and 𝙄 is the unit dyad, or alternatively,
𝑒𝛼2 𝑒𝛽2 1
𝐉𝛼\𝛽 = 4𝜋𝜆𝛼𝛽 {𝑓𝛼 (𝐯)∇𝐯 𝐻(𝐯) − ∇𝐯 ⋅ [𝑓𝛼 (𝐯)∇𝐯 ∇𝐯 𝐺(𝐯)]} ,
𝑚2𝛼 2
where the Rosenbluth potentials are
𝑚𝛼
𝐻(𝐯) = (1 + ) ∫ 𝑓𝛽 (𝐯′ )𝑢−1 𝑑3𝑣′ .
𝑚𝛽
If species 𝛼 is a weak beam (number and energy density small compared
with background) streaming through a Maxwellian plasma, then
𝑚𝛼 𝛼\𝛽 1 𝛼\𝛽
𝐉𝛼\𝛽 = − 𝜈𝑠 𝐯𝑓𝛼 − 𝜈∥ 𝐯𝐯 ⋅ ∇𝐯 𝑓𝛼
𝑚𝛼 + 𝑚𝛽 2
1 𝛼\𝛽 2
− 𝜈 (𝑣 𝙄 − 𝐯𝐯) ⋅ ∇𝐯 𝑓𝛼 .
4 ⟂
B-G-K Collision Operator
For distribution functions with no large gradients in velocity space, the Fokker-
Planck collision terms can be approximated according to
𝐷𝑓𝑒
= 𝜈𝑒𝑒 (𝐹𝑒 − 𝑓𝑒 ) + 𝜈𝑒𝑖 (𝐹𝑒̄ − 𝑓𝑒 );
𝐷𝑡
𝐷𝑓𝑖
= 𝜈𝑖𝑒 (𝐹𝑖̄ − 𝑓𝑖 ) + 𝜈𝑖𝑖 (𝐹𝑖 − 𝑓𝑖 ).
𝐷𝑡
𝛼\𝛽
The respective slowing-down rates 𝜈𝑠 given in the Relaxation Rate section
above can be used for 𝜈𝛼𝛽 , assuming slow ions and fast electrons, with 𝜖 re-
35
placed by 𝑇𝛼 . (For 𝜈𝑒𝑒 and 𝜈𝑖𝑖 , one can equally well use 𝜈⟂ , and the result is
insensitive to whether the slow- or fast-test-particle limit is employed.) The
Maxwellians 𝐹𝛼 and 𝐹𝛼̄ are given by
3/2
𝑚𝛼 𝑚𝛼 (𝐯 − 𝐯𝛼 )2
𝐹𝛼 = 𝑛𝛼 ( ) exp {− [ ]} ;
2𝜋𝑘𝑇𝛼 2𝑘𝑇𝛼
3/2
𝑚𝛼 𝑚 (𝐯 − 𝐯̄ 𝛼 )2
𝐹𝛼̄ = 𝑛𝛼 ( ) exp {− [ 𝛼 ]} ,
2𝜋𝑘𝑇𝛼̄ 2𝑘𝑇𝛼̄
where 𝑛𝛼 , 𝐯𝛼 and 𝑇𝛼 are the number density, mean drift velocity, and effec-
tive temperature obtained by taking moments of 𝑓𝛼 . Some latitude in the
definition of 𝑇𝛼̄ and 𝐯̄ 𝛼 is possible;20 one choice is 𝑇𝑒̄ = 𝑇𝑖 , 𝑇𝑖̄ = 𝑇𝑒 , 𝐯̄ 𝑒 = 𝐯𝑖 ,
𝐯̄ 𝑖 = 𝐯𝑒 .
Transport Coefficients
Transport equations for a multispecies plasma:
𝑑𝛼 𝑛𝛼
+ 𝑛𝛼 ∇ ⋅ 𝐯𝛼 = 0;
𝑑𝑡
𝑑𝛼 𝐯𝛼 1
𝑚𝛼 𝑛𝛼 = −∇𝑝𝛼 − ∇ ⋅ 𝝥𝛼 + 𝑍𝛼 𝑒𝑛𝛼 [𝐄 + 𝐯𝛼 × 𝐁] + 𝐑𝛼 ;
𝑑𝑡 𝑐
3 𝑑𝛼 𝑘𝑇𝛼
𝑛 + 𝑝𝛼 ∇ ⋅ 𝐯𝛼 = −∇ ⋅ 𝐪𝛼 − 𝝥𝛼 ∶ ∇𝐯𝛼 + 𝑄𝛼 .
2 𝛼 𝑑𝑡
Here 𝑑 /𝑑𝑡 ≡ ∂/∂𝑡 + 𝐯𝛼 ⋅ ∇; 𝑝𝛼 = 𝑛𝛼 𝑘𝑇𝛼 , where 𝑘 is Boltzmann’s constant;
𝛼
𝐑𝛼 = ∑𝛽 𝐑𝛼𝛽 and 𝑄𝛼 = ∑𝛽 𝑄𝛼𝛽 , where 𝐑𝛼𝛽 and 𝑄𝛼𝛽 are respectively the
momentum and energy gained by the 𝛼th species through collisions with the
𝛽 th ; 𝝥𝛼 is the stress tensor; and 𝐪𝛼 is the heat flow.
The transport coefficients in a simple two-component plasma (electrons and
singly charged ions) are tabulated below. Here ∥ and ⟂ refer to the directions
relative to the magnetic field 𝐁 = 𝐛𝐵; 𝐮 = 𝐯𝑒 − 𝐯𝑖 is the relative streaming
velocity; 𝑛𝑒 = 𝑛𝑖 ≡ 𝑛; 𝐣 = −𝑛𝑒𝐮 is the current; and the basic collisional times
are taken to be
3√𝑚𝑒 (𝑘𝑇𝑒 )3/2 𝑇𝑒3/2
𝜏𝑒 = = 3.44 × 105 sec,
4√2𝜋 𝑛𝜆𝑒4 𝑛𝜆
where 𝜆 is the Coulomb logarithm, and
3√𝑚𝑖 (𝑘𝑇𝑖 )3/2 𝑇𝑖3/2 1/2
𝜏𝑖 = = 2.09 × 107 𝜇 sec.
4√𝜋𝑛 𝜆𝑒4 𝑛𝜆
36
In the limit of large fields (𝜔𝑐𝛼 𝜏𝛼 ≫ 1, 𝛼 = 𝑖, 𝑒) the transport processes may
be summarized as follows:21𝑎,𝑏
momentum transfer R𝑒𝑖 = −R𝑖𝑒 ≡ R = R𝐮 + R𝑇 ;
𝑛𝑒
frictional force R𝐮 = (0.51𝐣∥ + 𝐣⟂ ); 𝜎0 = 𝑛𝑒2 𝜏𝑒 /𝑚𝑒
𝜎0
3𝑛
thermal force R𝑇 = −0.71𝑛∇∥ (𝑘𝑇𝑒 ) − 𝐛 × ∇⟂ (𝑘𝑇𝑒 )
2𝜔𝑐𝑒 𝜏𝑒
3𝑚𝑒 𝑛𝑘
ion heating 𝑄𝑖 = (𝑇 − 𝑇𝑖 );
𝑚𝑖 𝜏𝑒 𝑒
electron heating 𝑄𝑒 = −𝑄𝑖 − R ⋅ 𝐮;
ion heat flux 𝐪𝑖 = −𝜅∥𝑖 ∇∥ (𝑘𝑇𝑖 ) − 𝜅⟂𝑖 ∇⟂ (𝑘𝑇𝑖 ) + 𝜅∧𝑖 𝐛 × ∇⟂ (𝑘𝑇𝑖 )
𝑛𝑘𝑇𝑖 𝜏𝑖 2𝑛𝑘𝑇𝑖 5𝑛𝑘𝑇𝑖
ion thermal 𝜅∥𝑖 = 3.9 ; 𝜅⟂𝑖 = 2
; 𝜅∧𝑖 =
conductivities 𝑚𝑖 𝑚𝑖 𝜔𝑐𝑖 𝜏𝑖 2𝑚𝑖 𝜔𝑐𝑖
electron heat flux 𝐪𝑒 = 𝐪𝑒𝐮 + 𝐪𝑒𝑇
3𝑛𝑘𝑇𝑒
frictional heat flux 𝐪𝑒𝐮 = 0.71𝑛𝑘𝑇𝑒 𝐮∥ + 𝐛 × 𝐮⟂
2𝜔𝑐𝑒 𝜏𝑒
thermal gradient 𝐪𝑒𝑇 𝑒 𝑒
= −𝜅∥ ∇∥ (𝑘𝑇𝑒 ) − 𝜅⟂ ∇⟂ (𝑘𝑇𝑒 ) − 𝜅∧𝑒 𝐛 × ∇⟂ (𝑘𝑇𝑒 )
heat flux
𝑛𝑘𝑇𝑒 𝜏𝑒 𝑛𝑘𝑇𝑒 5𝑛𝑘𝑇𝑒
electron thermal 𝜅∥𝑒 = 3.2 ; 𝜅⟂𝑒 = 4.7 2
; 𝜅∧𝑒 =
conductivities 𝑚𝑒 𝑚𝑒 𝜔𝑐𝑒 𝜏𝑒 2𝑚𝑒 𝜔𝑐𝑒
𝜂 𝜂
stress tensor (either 𝑥𝑥 = − 0 (𝑊𝑥𝑥 + 𝑊𝑦𝑦 ) − 1 (𝑊𝑥𝑥 − 𝑊𝑦𝑦 ) − 𝜂3 𝑊𝑥𝑦 ;
species) 2 2
𝜂0 𝜂1
𝑦𝑦 = − (𝑊𝑥𝑥 + 𝑊𝑦𝑦 ) + (𝑊𝑥𝑥 − 𝑊𝑦𝑦 ) + 𝜂3 𝑊𝑥𝑦 ;
2 2
𝜂
𝑥𝑦 = 𝑦𝑥 = −𝜂1 𝑊𝑥𝑦 + 3 (𝑊𝑥𝑥 − 𝑊𝑦𝑦 );
2
𝑥𝑧 = 𝑧𝑥 = −𝜂2 𝑊𝑥𝑧 − 𝜂4 𝑊𝑦𝑧 ;
𝑦𝑧 = 𝑧𝑦 = −𝜂2 𝑊𝑦𝑧 + 𝜂4 𝑊𝑥𝑧 ;
𝑧𝑧 = −𝜂0 𝑊𝑧𝑧
(here the 𝑧 axis is defined parallel to B);
3𝑛𝑘𝑇𝑖 6𝑛𝑘𝑇𝑖
ion viscosity 𝜂0𝑖 = 0.96𝑛𝑘𝑇𝑖 𝜏𝑖 ; 𝜂1𝑖 = 2
; 𝜂2𝑖 = 2
;
10𝜔𝑐𝑖 𝜏𝑖 5𝜔𝑐𝑖 𝜏𝑖
𝑛𝑘𝑇 𝑖 𝑛𝑘𝑇 𝑖
𝜂3𝑖 = ; 𝜂4𝑖 = ;
2𝜔𝑐𝑖 𝜔𝑐𝑖
𝑛𝑘𝑇 𝑛𝑘𝑇
electron viscosity 𝜂𝑒0 = 0.73𝑛𝑘𝑇𝑒 𝜏𝑒 ; 𝜂𝑒1 = 0.51 2 𝑒 ; 𝜂𝑒2 = 2.0 2 𝑒 ;
𝜔𝑐𝑒 𝜏𝑒 𝜔𝑐𝑒 𝜏𝑒
𝑛𝑘𝑇𝑒 𝑛𝑘𝑇𝑒
𝜂𝑒3 = − ; 𝜂𝑒4 = − .
2𝜔𝑐𝑒 𝜔𝑐𝑒
37
For both species the rate-of-strain tensor is defined as
∂𝑣𝑗 ∂𝑣 2
𝑊𝑗𝑘 = + 𝑘 − 𝛿𝑗𝑘 ∇ ⋅ 𝐯.
∂𝑥𝑘 ∂𝑥𝑗 3
When B = 0 the following simplifications occur:
R𝐮 = 𝑛𝑒𝐣/𝜎∥ ; R𝑇 = −0.71𝑛∇(𝑘𝑇𝑒 ); 𝐪𝑖 = −𝜅∥𝑖 ∇(𝑘𝑇𝑖 );
𝐪𝑒𝐮 = 0.71𝑛𝑘𝑇𝑒 𝐮; 𝐪𝑒𝑇 = −𝜅∥𝑒 ∇(𝑘𝑇𝑒 ); 𝑗𝑘 = −𝜂0 𝑊𝑗𝑘 .
For 𝜔𝑐𝑒 𝜏𝑒 ≫ 1 ≫ 𝜔𝑐𝑖 𝜏𝑖 , the electrons obey the high-field expressions and the
ions obey the zero-field expressions.
Collisional transport theory is applicable when (1) macroscopic time rates of
change satisfy 𝑑/𝑑𝑡 ≪ 1/𝜏, where 𝜏 is the longest collisional time scale, and
(in the absence of a magnetic field) (2) macroscopic length scales 𝐿 satisfy
𝐿 ≫ 𝑙, where 𝑙 = 𝑣𝜏̄ is the mean free path. In a strong field, 𝜔𝑐𝑒 𝜏 ≫ 1, con-
dition (2) is replaced by 𝐿∥ ≫ 𝑙 and 𝐿⟂ ≫ √𝑙𝑟𝑒 (𝐿⟂ ≫ 𝑟𝑒 in a uniform field),
where 𝐿∥ is a macroscopic scale parallel to the field B and 𝐿⟂ is the smaller
of 𝐵/|∇⟂ 𝐵| and the transverse plasma dimension. In addition, the standard
transport coefficients are valid only when (3) the Coulomb logarithm satis-
fies 𝜆 ≫ 1; (4) the electron gyroradius satisfies 𝑟𝑒 ≫ 𝜆𝐷 , or 8𝜋𝑛𝑒 𝑚𝑒 𝑐2 ≫ 𝐵 2 ;
(5) relative drifts 𝐮 = 𝐯𝛼 − 𝐯𝛽 between two species are small compared with
the thermal velocities, i.e., 𝑢2 ≪ 𝑘𝑇𝛼 /𝑚𝛼 , 𝑘𝑇𝛽 /𝑚𝛽 ; and (6) anomalous trans-
port processes owing to microinstabilities are negligible.
Weakly Ionized Plasmas
Collision frequency for scattering of charged particles of species 𝛼 by neu-
trals is
𝛼|0
𝜈𝛼 = 𝑛0 𝜎𝑠 (𝑘𝑇𝛼 /𝑚𝛼 )1/2 ,
𝛼|0
where 𝑛0 is the neutral density, 𝜎𝑠 is the cross section, typically ∼ 5 × 10−15
cm2 and weakly dependent on temperature, and (𝑇0 /𝑚0 )1/2 <
(𝑇𝛼 /𝑚𝛼 )1/2 where 𝑇0 and 𝑚0 are the temperature and mass of the neutrals.
When the system is small compared with a Debye length, 𝐿 ≪ 𝜆𝐷 , the
charged particle diffusion coefficients are
𝐷𝛼 = 𝑘𝑇𝛼 /𝑚𝛼 𝜈𝛼 ,
In the opposite limit, both species diffuse at the ambipolar rate
𝜇 𝐷 − 𝜇𝑒 𝐷𝑖 (𝑇 + 𝑇𝑒 )𝐷𝑖 𝐷𝑒
𝐷𝐴 = 𝑖 𝑒 = 𝑖 ,
𝜇𝑖 − 𝜇𝑒 𝑇𝑖 𝐷𝑒 + 𝑇𝑒 𝐷𝑖
38
where 𝜇𝛼 = 𝑒𝛼 /𝑚𝛼 𝜈𝛼 is the mobility. The conductivity 𝜎𝛼 satisfies 𝜎𝛼 =
𝑛𝛼 𝑒𝛼 𝜇𝛼 .
In the presence of a magnetic field B the scalars 𝜇 and 𝜎 become tensors,
𝐉𝛼 = 𝜎 𝛼 ⋅ E = 𝜎∥𝛼 E∥ + 𝜎⟂𝛼 E⟂ + 𝜎∧𝛼 E × 𝐛,
where 𝐛 = B/𝐵 and
𝜎∥𝛼 = 𝑛𝛼 𝑒𝛼2 /𝑚𝛼 𝜈𝛼 ;
𝜎⟂𝛼 = 𝜎∥𝛼 𝜈𝛼2 /(𝜈𝛼2 + 𝜔𝑐𝛼
2
);
𝜎∧𝛼 = 𝜎∥𝛼 𝜈𝛼 𝜔𝑐𝛼 /(𝜈𝛼2 + 𝜔𝑐𝛼
2
).
Here 𝜎⟂ and 𝜎∧ are the Pedersen and Hall conductivities, respectively.
39
APPROXIMATE MAGNITUDES IN SOME TYPICAL PLASMAS
3
Plasma Type 𝑛 cm−3 𝑇 eV 𝜔𝑝𝑒 sec−1 𝜆𝐷 cm 𝑛𝜆𝐷 𝜈𝑒𝑖 sec−1
40
25
50% ionization
hydrogen plasma
(4π/3)nλ3D < 1
Laser
Plasma Focus
20
15
log10 n (cm-3)
Fusion
Low experiments
pressure
Alkali
metal
plasma
10
Solar
Glow corona
discharge
Flames
λD > 1 cm
Earth
5 iono-
shpere
41
IONOSPHERIC PARAMETERS23
The following tables give average nighttime values. Where two numbers are
entered, the first refers to the lower and the second to the upper portion of
the layer.
43
THERMONUCLEAR FUSION26
Natural abundance of isotopes:
hydrogen 𝑛D /𝑛H = 1.5 × 10−4
helium 𝑛He3 /𝑛He4 = 1.3 × 10−6
lithium 𝑛Li6 /𝑛Li7 = 0.08
Mass ratios:
𝑚𝑒 /𝑚D = 2.72 × 10−4 = 1/3670
(𝑚𝑒 /𝑚D )1/2 = 1.65 × 10−2 = 1/60.6
𝑚𝑒 /𝑚T = 1.82 × 10−4 = 1/5496
(𝑚𝑒 /𝑚T )1/2 = 1.35 × 10−2 = 1/74.1
Fusion reactions (branching ratios are correct for energies near the cross sec-
tion peaks; a negative yield means the reaction is endothermic):27
(1a) D + D ⃗ 50% T(1.01 MeV) + p(3.02 MeV)
3
(1b) ⃗50% He (0.82 MeV) + n(2.45 MeV)
4
(2) D + T ⃗ He (3.5 MeV) + n(14.1 MeV)
(3) D + He3 ⃗ He4 (3.6 MeV) + p(14.7 MeV)
(4) T + T ⃗ He4 + 2n + 11.3 MeV
(5a) He3 + T ⃗ 4
51% He + p + n + 12.1 MeV
4
(5b) ⃗43% He (4.8 MeV) + D(9.5 MeV)
5
(5c) ⃗ 6% He (1.89 MeV) + p(9.46 MeV)
(6) p + Li6 ⃗ He4 (1.7 MeV) + He3 (2.3 MeV)
(7a) p + Li7 ⃗ 4
20% 2 He + 17.3 MeV
7
(7b) ⃗80% Be + n − 1.6 MeV
(8) D + Li6 ⃗ 2He4 + 22.4 MeV
(9) p + B11 ⃗ 3 He4 + 8.7 MeV
(10) n + Li6 ⃗ He4 (2.1 MeV) + T(2.7 MeV)
The total cross section in barns (1 barn = 10−24 cm2 ) as a function of 𝐸, the
energy in keV of the incident particle [the first ion on the left side of Eqs. (1)–
(5)], assuming the target ion at rest, can be fitted by28𝑎
−1
𝐴5 + [(𝐴4 − 𝐴3 𝐸)2 + 1] 𝐴2
𝜎𝑇 (𝐸) =
𝐸 [exp(𝐴1 𝐸−1/2 ) − 1]
where the Duane coefficients 𝐴𝑗 for the principal fusion reactions are as fol-
lows:
44
D–D D–D D–T D–He3 T–T T–He3
(1a) (1b) (2) (3) (4) (5a–c)
𝐴1 46.097 47.88 45.95 89.27 38.39 123.1
𝐴2 372 482 5.02 × 104 2.59 × 104 448 11250
𝐴3 4.36 × 10−4 3.08 × 10−4 1.368 × 10−2 3.98 × 10−3 1.02 × 10−3 0
𝐴4 1.220 1.177 1.076 1.297 2.09 0
𝐴5 0 0 409 647 0 0
45
RELATIVISTIC ELECTRON BEAMS
2 −1/2
Here 𝛾 = (1 − 𝛽 ) is the relativistic scaling factor; quantities in analytic
formulas are expressed in SI or cgs units, as indicated; in numerical formulas,
𝐼 is in amperes (A), 𝐵 is in gauss (G), electron linear density 𝑁 is in cm−1 ,
and temperature, voltage and energy are in MeV; 𝛽𝑧 = 𝑣𝑧 /𝑐; 𝑘 is Boltzmann’s
constant.
Relativistic electron gyroradius:
𝑚𝑐2 2
𝑟𝑒 = (𝛾 − 1)1/2 (cgs) = 1.70 × 103 (𝛾2 − 1)1/2 𝐵 −1 cm.
𝑒𝐵
Relativistic electron energy:
𝑊 = 𝑚𝑐2 𝛾 = 0.511𝛾 MeV.
Alfvén-Lawson limit:
𝐼𝐴 = (𝑚𝑐3 /𝑒)𝛽𝑧 𝛾 (cgs) = (4𝜋𝑚𝑐/𝜇0 𝑒)𝛽𝑧 𝛾 (SI) = 1.70 × 104 𝛽𝑧 𝛾 A.
47
BEAM INSTABILITIES30
48
Parameters of Most Unstable Mode
Name Growth Rate Frequency Wave Group
Number Velocity
1 𝜔𝑒
Electron- 𝜔 0 0.9 0
2 𝑒 𝑉𝑑
electron
𝑚 1/3 𝑚 1/3 𝜔𝑒 2
Buneman 0.7 ( ) 𝜔𝑒 0.4 ( ) 𝜔𝑒 𝑉
𝑀 𝑀 𝑉𝑑 3 𝑑
1/3 1/3
𝑛 𝑛 𝜔𝑒 2
Beam-plasma 0.7 ( 𝑏 ) 𝜔𝑒 𝜔𝑒 − 0.4 ( 𝑏 ) 𝜔𝑒 𝑉
𝑛𝑝 𝑛𝑝 𝑉𝑏 3 𝑏
2
𝑛𝑏 𝑉𝑏 𝜔𝑒 3𝑉𝑒̄ 2
Weak ( ) 𝜔𝑒 𝜔𝑒
2𝑛𝑝 𝑉𝑏̄ 𝑉𝑏 𝑉𝑏
beam-plasma
1/2
𝑛𝑏 𝑉𝑒̄ 𝑉𝑏
Beam-plasma ( ) 𝜔 𝜔𝑒 𝜆−1 𝑉𝑏
𝑛𝑝 𝑉𝑏 𝑒 𝑉𝑒̄ 𝐷
(hot-electron)
𝑚 1/2
Ion acoustic ( ) 𝜔𝑖 𝜔𝑖 𝜆−1
𝐷 𝐶𝑠
𝑀
Anisotropic Ω𝑒 𝜔𝑒 cos 𝜃 ∼ Ω𝑒 𝑟𝑒−1 ̄
𝑉𝑒⟂
temperature
(hydro)
1 ̄
Ion cyclotron 0.1Ω𝑖 1.2Ω𝑖 𝑟𝑖−1 𝑉
3 𝑖
Beam-cyclotron 0.7Ω𝑒 𝑛Ω𝑒 0.7𝜆−1
𝐷 ≳ 𝑉𝑑 ;
(hydro) ≲ 𝐶𝑠
1 Ω𝐻 1
Modified Ω 0.9Ω𝐻 1.7 𝑉
2 𝐻 𝑉𝑑 2 𝑑
two-stream
(hydro)
Ω𝐻
Ion-ion 0.4Ω𝐻 0 1.2 0
𝑈
(equal beams)
𝜔𝑖
Ion-ion 0.4𝜔𝑖 0 1.2 0
𝑈
(equal beams)
For nomenclature, see p. 50.
49
In the preceding tables, subscripts 𝑒, 𝑖, 𝑑, 𝑏, 𝑝 stand for “electron,” “ion,”
“drift,” “beam,” and “plasma,” respectively. Thermal velocities are denoted
by a bar. In addition, the following are used:
𝑚 electron mass 𝑟𝑒 , 𝑟𝑖 gyroradius
𝑀 ion mass 𝛽 plasma/magnetic energy
𝑉 velocity density ratio
𝑇 temperature 𝑉𝐴 Alfvén speed
𝑛𝑒 , 𝑛𝑖 number density Ω𝑒 , Ω𝑖 gyrofrequency
𝑛 harmonic number Ω𝐻 hybrid gyrofrequency,
2
𝐶𝑠 = (𝑇𝑒 /𝑀)1/2 ion sound speed Ω𝐻 = Ω𝑒 Ω𝑖
𝜔𝑒 , 𝜔𝑖 plasma frequency 𝑈 relative drift velocity of
𝜆𝐷 Debye length two ion species
50
LASERS
System Parameters
Efficiencies and power levels are approximate.31
Wavelength Power levels available (W)
Type (μm) Efficiency Pulsed CW
CO2 10.6 0.01 − 0.02 > 2 × 1013 > 105
(pulsed)
CO 5 0.4 > 109 > 100
Holmium 2.06 0.03† − 0.1‡ > 107 80
Iodine 1.315 0.003 3 × 1012 −
Nd-glass 1.06 − 1.25 × 1015 −
Nd:YAG 1.064 − 109 > 104
Nd:YLF 1.045, − 4 × 108 80
1.54, 1.313
Nd:YVO4 1.064 − − > 20
Er:YAG 2.94 − 1.5 × 105 −
*Color center 1−4 10−3 5 × 108 1
*Ti:Sapphire 0.7 − 1.5 0.4 × 𝜂𝑝 1014 150
−3
Ruby 0.6943 < 10 1010 1
He-Ne 0.6328 10−4 − 1 − 50 × 10−3
*Argon ion 0.45 − 0.60 10−3 5 × 104 150
*OPO 0.3 − 10 > 0.1 × 𝜂𝑝 1010 5
N2 0.3371 0.001 − 0.05 106 −
*Dye 0.3 − 1.1 10−3 5 × 107 > 100
Kr-F 0.26 0.08 1012 500
Xenon 0.175 0.02 > 108 −
Ytterbium fiber 1.05 − 1.1 0.55 5 × 107 104
Erbium fiber 1.534 − 7 × 106 100
Semiconductor 0.375 − 1.9 > 0.5 3 × 109 > 103
*Tunable sources †lamp-driven ‡diode-driven
Nd stands for Neodymium; Er stands for Erbium; Ti stands for Titanium;
YAG stands for Yttrium–Aluminum Garnet; YLF stands for Yttrium Lithium
Fluoride; YVO5 stands for Yttrium Vanadate; OPO for Optical Parametric
Oscillator; 𝜂𝑝 is pump laser efficiency.
51
Formulas
An e-m wave with 𝐤 ∥ 𝐁 has an index of refraction given by
𝑛± = [1 − 𝜔𝑝𝑒2 /𝜔(𝜔 ∓ 𝜔𝑐𝑒 )]1/2 ,
where ± refers to the helicity. The rate of change of polarization angle 𝜃 as a
function of displacement 𝑠 (Faraday rotation) is given by
𝑑𝜃/𝑑𝑠 = (𝑘/2)(𝑛− − 𝑛+ ) = 2.36 × 104 𝑁𝐵𝑓−2 cm−1 ,
where 𝑁 is the electron number density, 𝐵 is the field strength, and 𝑓 is the
wave frequency, all in cgs.
The quiver velocity of an electron in an e-m field of angular frequency 𝜔 is
𝑣0 = 𝑒𝐸max /𝑚𝜔 = 25.6𝐼 1/2 𝜆0 cm sec−1
2
in terms of the laser flux 𝐼 = 𝑐𝐸max /8𝜋, with 𝐼 in watt/cm2 , laser wavelength
𝜆0 in μm. The ratio of quiver energy to thermal energy is
2
𝑊qu /𝑊th = 𝑚𝑒 𝑣0 2 /2𝑘𝑇 = 1.81 × 10−13 𝜆0 𝐼/𝑇,
where 𝑇 is given in eV. For example, if 𝐼 = 1015 W cm−2 , 𝜆0 = 1 μm, 𝑇 =
2 keV, then 𝑊qu /𝑊th ≈ 0.1.
Pondermotive force:
ℱ = 𝑁∇⟨𝐸 2 ⟩/8𝜋𝑁𝑐 ,
where
𝑁𝑐 = 1.1 × 1021 𝜆−2 −3
0 cm .
52
ATOMIC PHYSICS AND RADIATION
Energies and temperatures are in eV; all other units are cgs except where
noted. 𝑍 is the charge state (𝑍 = 0 refers to a neutral atom); the subscript 𝑒
labels electrons. 𝑁 refers to number density, 𝑛 to principal quantum number.
Asterisk superscripts on level population densities denote local thermody-
namic equilibrium (LTE). Thus 𝑁𝑛 * is the LTE number density of atoms (or
ions) in level 𝑛.
53
Rate for electron collisional deexcitation:
(5) 𝑌𝑛𝑚 = (𝑁𝑚 */𝑁𝑛 *)𝑋𝑚𝑛 .
Here 𝑁𝑚 */𝑁𝑛 * = (𝑔𝑚 /𝑔𝑛 ) exp(Δ𝐸𝑛𝑚 /𝑇𝑒 ) is the Boltzmann relation for level
population densities, where 𝑔𝑛 is the statistical weight of level 𝑛.
54
Classical ionization cross-section36 for any atomic shell 𝑗
(11) 𝜎𝑖 = 6 × 10−14 𝑏𝑗 𝑔𝑗 (𝑥)/𝑈𝑗 2 cm2 .
Here 𝑏𝑗 is the number of shell electrons; 𝑈𝑗 is the binding energy of the ejected
electron; 𝑥 = 𝜖/𝑈𝑗 , where 𝜖 is the incident electron energy; and 𝑔 is a univer-
sal function with a minimum value 𝑔min ≈ 0.2 at 𝑥 ≈ 4.
Ionization from the ground state, averaged over Maxwellian electron distri-
𝑍
bution, for 0.02 ≲ 𝑇𝑒 /𝐸∞ ≲ 100 (Ref. 35):
𝑍 1/2
(𝑇𝑒 /𝐸∞ ) 𝐸𝑍
(12) 𝑆(𝑍) = 10−5 exp (− ∞ ) cm3 /sec,
𝑍 )3/2 (6.0 + 𝑇 /𝐸 𝑍 )
(𝐸∞ 𝑒 ∞ 𝑇𝑒
𝑍
where 𝐸∞ is the ionization energy.
55
Ionization Equilibrium Models
Saha equilibrium:39
𝑁𝑒 𝑁1 *(𝑍) 𝑔𝑍 𝑇𝑒 3/2 𝐸𝑍 (𝑛, 𝑙)
(17) = 6.0 × 1021 1 𝑍−1 exp (− ∞ ) cm−3 ,
𝑁𝑛 *(𝑍 − 1) 𝑔𝑛 𝑇𝑒
where 𝑔𝑍𝑛 is the statistical weight for level 𝑛 of charge state 𝑍 and 𝐸∞ 𝑍
(𝑛, 𝑙)
is the ionization energy of the neutral atom initially in level (𝑛, 𝑙), given by
Eq. (2).
(a) Collisional and radiative excitation rates for a level 𝑛 must satisfy
(19) 𝑌𝑛𝑚 ≳ 10𝐴𝑛𝑚 .
56
Radiation
Note: Energies and temperatures are in eV; all other quantities are in cgs
units except where noted. 𝑍 is the charge state (𝑍 = 0 refers to a neutral
atom); the subscript 𝑒 labels electrons. 𝑁 is number density.
Doppler width:
(25) Δ𝜆/𝜆 = 7.7 × 10−5 (𝑇/𝜇)1/2 ,
where 𝜇 is the mass of the emitting atom or ion scaled by the proton mass.
57
Bremsstrahlung from hydrogen-like plasma:26
3
(30) 𝑃Br = 1.69 × 10−32 𝑁𝑒 𝑇𝑒 1/2 ∑ [𝑍 2 𝑁(𝑍)] watt/cm ,
where the sum is over all ionization states 𝑍.
Lengths
frictional dissipation length 𝐿𝜈 = 𝑣𝑇𝑑 /𝜈𝑛𝑑
dust Coulomb radius 𝑅𝐶𝑒,𝑖 = |𝑍|𝑒2 /𝑘𝑇𝑒,𝑖
dust gyroradius 𝑟𝑑 = 𝑣𝑇𝑑 /𝜔𝑐𝑑
Grain Charging
The charge evolution equation is 𝑑|𝑍|/𝑑𝑡 = 𝐼𝑖 − 𝐼𝑒 . From orbital motion
limited (OML) theory46 in the collisionless limit 𝑙𝑒𝑛(𝑖𝑛) ≫ 𝜆𝐷 ≫ 𝑎:
𝑇𝑒
𝐼𝑒 = √8𝜋𝑎2 𝑛𝑒 𝑣𝑇𝑒 exp(−𝑧), 𝐼𝑖 = √8𝜋𝑎2 𝑛𝑖 𝑣𝑇𝑖 (1 + 𝑧) .
𝑇𝑖
Grains are charged negatively. The grain charge can vary in response to spa-
tial and temporal variations of the plasma. Charge fluctuations are always
present, with frequency 𝜔ch . Other charging mechanisms are photoemission,
secondary emission, thermionic emission, field emission, etc. Charged dust
grains change the plasma composition, keeping quasineutrality. A measure
of this is the Havnes parameter 𝑃 = |𝑍|𝑛𝑑 /𝑛𝑒 . The balance of 𝐼𝑒 and 𝐼𝑖 yields
1/2
𝑚𝑖 𝑇𝑖 𝑇
exp(−𝑧) = ( ) (1 + 𝑒 𝑧) [1 + 𝑃(𝑧)]
𝑚𝑒 𝑇𝑒 𝑇𝑖
When the relative charge density of dust is large, 𝑃 ≫ 1, the grain charge Z
monotonically decreases.
Forces and momentum transfer
In addition to the usual electromagnetic forces, grains in complex plasmas
63
are also subject to: gravity force 𝐅g = 𝑚𝑑 𝐠; thermophoretic force
4√2𝜋 2
𝐅th = − (𝑎 /𝑣𝑇𝑛 )𝜅𝑛 ∇𝑇𝑛
15
(where 𝜅𝑛 is the coefficient of gas thermal conductivity); forces associated
with the momentum transfer from other species, 𝐅𝛼 = −𝑚𝑑 𝜈𝛼𝑑 𝐕𝛼𝑑 , i.e., neu-
tral, ion, and electron drag. For collisions between charged particles, two
limiting cases are distinguished by the magnitude of the scattering parame-
ter 𝛽𝛼 . When 𝛽𝛼 ≪ 1 the result is independent of the sign of the potential.
When 𝛽𝛼 ≫ 1, the results for repulsive and attractive interaction potentials
are different. For typical complex plasmas the hierarchy of scattering param-
eters is 𝛽𝑒 (∼ 0.01 − 0.3) ≪ 𝛽𝑖 (∼ 1 − 30) ≪ 𝛽𝑑 (∼ 103 − 3 × 104 ). The generic
expressions for different types of collisions are47
𝜈𝛼𝑑 = (4√2𝜋/3)(𝑚𝛼 /𝑚𝑑 )𝑎2 𝑛𝛼 𝑣𝑇𝛼 Φ𝛼𝑑
Electron-dust collisions
1
Φ𝑒𝑑 ≃ 𝑧2 Λ𝑒𝑑 , 𝛽𝑒 ≪ 1
2
Ion-dust collisions
1
𝑧2 (𝑇𝑒 /𝑇𝑖 )2 Λ𝑖𝑑 , 𝛽𝑖 < 5
Φ𝑖𝑑 = { 2 2
2(𝜆𝐷 /𝑎)2 (ln 𝛽𝑖 + 2 ln 𝛽𝑖 + 2), 𝛽𝑖 > 13
Dust-dust collisons
𝑧2 Λ , 𝛽𝑑 ≪ 1
Φ𝑑𝑑 = { 𝑑 𝑑𝑑 2
(𝜆𝐷 /𝑎) [ln 4𝛽𝑑 − ln ln 4𝛽𝑑 ], 𝛽𝑑 ≫ 1
where 𝑧𝑑 ≡ 𝑍 2 𝑒2 /𝑎𝑘𝑇𝑑 .
For 𝜈𝑑𝑑 ∼ 𝜈𝑛𝑑 the complex plasma is in a two-phase state, and for 𝜈𝑛𝑑 ≫ 𝜈𝑑𝑑
we have merely tracer particles (dust-neutral gas interaction dominates). The
momentum transfer cross section is proportional to the Coulomb logarithm
Λ𝛼𝑑 when the Coulomb scattering theory is applicable. It is determined by
integration over the impact parameters, from 𝜌min to 𝜌max . 𝜌min is due to fi-
nite grain size and is given by OML theory. 𝜌max = 𝜆𝐷 for repulsive inter-
action (applicable for 𝛽𝛼 ≪ 1), and 𝜌max = 𝜆𝐷 (1 + 2𝛽𝛼 )1/2 for attractive
interaction (applicable up to 𝛽𝛼 < 5).
64
For repulsive interaction (electron-dust and dust-dust)
∞
Λ𝛼𝑑 = 𝑧𝛼 ∫ e−𝑧𝛼 𝑥 ln[1 + 4(𝜆𝐷 /𝑎𝛼 )2 𝑥2 ]𝑑𝑥
0 ∞
− 2𝑧𝛼 ∫ e−𝑧𝛼 𝑥 ln(2𝑥 − 1)𝑑𝑥,
1
where 𝑧𝑒 = 𝑧, 𝑎𝑒 = 𝑎, and 𝑎𝑑 = 2𝑎.
For ion-dust (attraction)
∞
1 + 2(𝑇𝑖 /𝑇𝑒 )(𝜆𝐷 /𝑎)𝑥
Λ𝑖𝑑 ≃ 𝑧 ∫ e−𝑧𝑥 ln [ ] 𝑑𝑥.
0
1 + 2(𝑇𝑖 /𝑇𝑒 )𝑥
For 𝜈𝑑𝑑 ≫ 𝜈𝑛𝑑 the complex plasma behaves like a one phase system (dust-
dust interaction dominates).
Phase Diagram of Complex Plasmas
The figure below represents different “phase states” of CDPs as functions of
the electrostatic coupling parameter Γ and 𝜅 or 𝛼, respectively. The vertical
dashed line at 𝜅 = 1 conditionally divides the system into Coulomb and
Yukawa parts. With respect to the usual plasma phase, in the diagram be-
low the complex plasmas are “located” mostly in the strong coupling regime
(equivalent to the top left corner).
α-1=Δ/a Regions I (V) represent Coulomb
10 100 1000 (Yukawa) crystals, the crystallization
4
condition is48 Γ > 106(1 + 𝜅 + 𝜅2 /2)−1 .
I V Regions II (VI) are for Coulomb
2
(Yukawa) non-ideal plasmas – the char-
log10(Γ)
II
acteristic range of dust-dust interaction
0 VI (in terms of the momentum transfer)
is larger than the intergrain distance
−2 III
VII VIII (in terms of the Wigner-Seitz radius),
IV
(𝜎/𝜋)1/2 > (4𝜋/3)−1/3 Δ, which implies
−4
0.1 1 10 that the interaction is essentially multi-
κ=Δ/λ particle.
Regions III (VII and VIII) correspond to Coulomb (Yukawa) ideal gases. The
range of dust-dust interaction is smaller than the intergrain distance and
only pair collisions are important. In addition, in the region VIII the pair
Yukawa interaction asymptotically reduces to the hard sphere limit, forming
a “Yukawa granular medium”. In region IV the electrostatic interaction is
unimportant and the system is like a usual granular medium.
65
REFERENCES
When any of the formulas and data in this collection are referenced in re-
search publications, it is suggested that the original source be cited rather
than the Formulary. Most of this material is well known and, for all practical
purposes, is in the “public domain.” Numerous colleagues and readers, too
numerous to list by name, have helped in collecting and shaping the Formu-
lary into its present form; they are sincerely thanked for their efforts.
Several book-length compilations of data relevant to plasma physics are avail-
able. The following are particularly useful:
• C. W. Allen, Astrophysical Quantities, 3rd edition (Athlone Press, London,
1976).
• A. Anders, A Formulary for Plasma Physics (Akademie-Verlag, Berlin,
1990).
• H. L. Anderson (Ed.), A Physicist’s Desk Reference, 2nd edition (American
Institute of Physics, New York, 1989).
• K. R. Lang, Astrophysical Formulae, 2nd edition (Springer, New York, 1980).
The books and articles cited below are intended primarily not for the pur-
pose of giving credit to the original workers, but (1) to guide the reader to
sources containing related material and (2) to indicate where to find deriva-
tions, explanations, examples, etc., which have been omitted from this compi-
lation. Additional material can also be found in D. L. Book, NRL Memoran-
dum Report No. 3332 (1977).
1. See M. Abramowitz and I. A. Stegun, Eds., Handbook of Mathematical
Functions (Dover, New York, 1968), pp. 1–3, for a tabulation of some
mathematical constants not available on pocket calculators.
2. H. W. Gould, “Note on Some Binomial Coefficient Identities of Rosen-
baum,” J. Math. Phys. 10, 49 (1969); H. W. Gould and J. Kaucky, “Evalu-
ation of a Class of Binomial Coefficient Summations,” J. Comb. Theory
1, 233 (1966).
3. B. S. Newberger, “New Sum Rule for Products of Bessel Functions with
Application to Plasma Physics,” J. Math. Phys. 23, 1278 (1982); 24, 2250
(1983).
4. P. M. Morse and H. Feshbach, Methods of Theoretical Physics (McGraw-Hill
66
Book Co., New York, 1953), Vol. I, pp. 47–52 and pp. 656–666.
5. W. D. Hayes, “A Collection of Vector Formulas,” Princeton University,
Princeton, NJ, 1956 (unpublished), and personal communication (1977).
6. See Quantities, Units and Symbols, report of the Symbols Committee of the
Royal Society, 2nd edition (Royal Society, London, 1975) for a discussion
of nomenclature in SI units.
7. E. R. Cohen and B. N. Taylor, “The 1986 Adjustment of the Fundamental
Physical Constants,” CODATA Bulletin No. 63 (Pergamon Press, New
York, 1986); J. Res. Natl. Bur. Stand. 92, 85 (1987); J. Phys. Chem. Ref.
Data 17, 1795 (1988).
8. E. S. Weibel, “Dimensionally Correct Transformations between Different
Systems of Units,” Amer. J. Phys. 36, 1130 (1968).
9. J. Stratton, Electromagnetic Theory (McGraw-Hill Book Co., New York,
1941), p. 508.
10. Reference Data for Engineers: Radio, Electronics, Computer, and Commu-
nication, 7th edition, E. C. Jordan, Ed. (Sams and Co., Indianapolis, IN,
1985), Chapt. 1. These definitions are International Telecommunica-
tions Union (ITU) Standards.
11. H. E. Thomas, Handbook of Microwave Techniques and Equipment (Pren-
tice-Hall, Englewood Cliffs, NJ, 1972), p. 9. Further subdivisions are
defined in Ref. 10, p. I–3.
12. J. P. Catchpole and G. Fulford, Ind. and Eng. Chem. 58, 47 (1966); reprinted
in recent editions of the Handbook of Chemistry and Physics (Chemical
Rubber Co., Cleveland, OH) on pp. F306–323.
13. W. D. Hayes, “The Basic Theory of Gasdynamic Discontinuities,” in Fun-
damentals of Gas Dynamics, Vol. III, High Speed Aerodynamics and Jet
Propulsion, H. W. Emmons, Ed. (Princeton University Press, Princeton,
NJ, 1958).
14. W. B. Thompson, An Introduction to Plasma Physics (Addison-Wesley
Publishing Co., Reading, MA, 1962), pp. 86–95.
15. L. D. Landau and E. M. Lifshitz, Fluid Mechanics, 2nd edition (Addison-
Wesley Publishing Co., Reading, MA, 1987), pp. 320–336.
16. The 𝑍 function is tabulated in B. D. Fried and S. D. Conte, The Plasma
67
Dispersion Function (Academic Press, New York, 1961).
17. R. W. Landau and S. Cuperman, “Stability of Anisotropic Plasmas to
Almost-Perpendicular Magnetosonic Waves,” J. Plasma Phys. 6, 495
(1971).
18. B. D. Fried, C. L. Hedrick, J. McCune, “Two-Pole Approximation for the
Plasma Dispersion Function,” Phys. Fluids 11, 249 (1968).
19. B. A. Trubnikov, “Particle Interactions in a Fully Ionized Plasma,” Reviews
of Plasma Physics, Vol. 1 (Consultants Bureau, New York, 1965), p. 105.
20. J. M. Greene, “Improved Bhatnagar–Gross–Krook Model of Electron-Ion
Collisions,” Phys. Fluids 16, 2022 (1973).
21. (a) S. I. Braginskii, “Transport Processes in a Plasma,” Reviews of Plasma
Physics, Vol. 1 (Consultants Bureau, New York, 1965), p. 205. (b) R. Balescu,
“Transport Processes in Plasma,” (North Holland Publishing, Amster-
dam, 1988), p. 211.
22. J. Sheffield, Plasma Scattering of Electromagnetic Radiation (Academic
Press, New York, 1975), p. 6 (after J. W. M. Paul).
23. K. H. Lloyd and G. Härendel, “Numerical Modeling of the Drift and De-
formation of Ionospheric Plasma Clouds and of their Interaction with
Other Layers of the Ionosphere,” J. Geophys. Res. 78, 7389 (1973).
24. C. W. Allen, Astrophysical Quantities, 3rd edition (Athlone Press, London,
1976), Chapt. 9.
25. G. L. Withbroe and R. W. Noyes, “Mass and Energy Flow in the Solar
Chromosphere and Corona,” Ann. Rev. Astrophys. 15, 363 (1977).
26. S. Glasstone and R. H. Lovberg, Controlled Thermonuclear Reactions (Van
Nostrand, New York, 1960), Chapt. 2.
27. References to experimental measurements of branching ratios and cross
sections are listed in F. K. McGowan, et al., Nucl. Data Tables A6, 353
(1969); A8, 199 (1970). The yields listed in the table are calculated di-
rectly from the mass defect.
28. (a) G. H. Miley, H. Towner and N. Ivich, Fusion Cross Section and Reac-
tivities, Rept. COO-2218-17 (University of Illinois, Urbana, IL, 1974);
B. H. Duane, Fusion Cross Section Theory, in Rept. BNWL-1685 (Battelle
Pacific Northwest Laboratory, 1972); (b) X.Z. Li, Q.M. Wei, and B. Liu,
68
“A new simple formula for fusion cross-sections of light nuclei,” Nucl.
Fusion 48, 125003 (2008).
29. J. M. Creedon, “Relativistic Brillouin Flow in the High 𝜈/𝛾 Limit,” J. Appl.
Phys. 46, 2946 (1975).
30. See, for example, A. B. Mikhailovskii, Theory of Plasma Instabilities Vol. I
(Consultants Bureau, New York, 1974). The table on pp. 48–49 was com-
piled by K. Papadopoulos.
31. Table prepared from data compiled by J. M. McMahon (personal com-
munication, D. Book, 1990) and A. Ting (personal communication, J.D.
Huba, 2004).
32. M. J. Seaton, “The Theory of Excitation and Ionization by Electron Im-
pact,” in Atomic and Molecular Processes, D. R. Bates, Ed. (New York,
Academic Press, 1962), Chapt. 11.
33. H. Van Regemorter, “Rate of Collisional Excitation in Stellar Atmospheres,”
Astrophys. J. 136, 906 (1962).
34. A. C. Kolb and R. W. P. McWhirter, “Ionization Rates and Power Loss
from 𝜃-Pinches by Impurity Radiation,” Phys. Fluids 7, 519 (1964).
35. R. W. P. McWhirter, “Spectral Intensities,” in Plasma Diagnostic Tech-
niques, R. H. Huddlestone and S. L. Leonard, Eds. (Academic Press,
New York, 1965).
36. M. Gryzinski, “Classical Theory of Atomic Collisions I. Theory of Inelas-
tic Collision,” Phys. Rev. 138A, 336 (1965).
37. M. J. Seaton, “Radiative Recombination of Hydrogenic Ions,” Mon. Not.
Roy. Astron. Soc. 119, 81 (1959).
38. Ya. B. Zel’dovich and Yu. P. Raizer, Physics of Shock Waves and High-
Temperature Hydrodynamic Phenomena (Academic Press, New York,
1966), Vol. I, p. 407.
39. H. R. Griem, Plasma Spectroscopy (Academic Press, New York, 1966).
40. T. F. Stratton, “X-Ray Spectroscopy,” in Plasma Diagnostic Techniques,
R. H. Huddlestone and S. L. Leonard, Eds. (Academic Press, New York,
1965).
41. G. Bekefi, Radiation Processes in Plasmas (Wiley, New York, 1966).
42. T. W. Johnston and J. M. Dawson, “Correct Values for High-Frequency
69
Power Absorption by Inverse Bremsstrahlung in Plasmas,” Phys. Fluids
16, 722 (1973).
43. W. L. Wiese, M. W. Smith, and B. M. Glennon, Atomic Transition Proba-
bilities, NSRDS-NBS 4, Vol. 1 (U.S. Govt. Printing Office, Washington,
1966).
44. F. M. Peeters and X. Wu, “Wigner crystal of a screened-Coulomb-interaction
colloidal system in two dimensions”, Phys. Rev. A 35, 3109 (1987)
45. S. Zhdanov, R. A. Quinn, D. Samsonov, and G. E. Morfill, “Large-scale
steady-state structure of a 2D plasma crystal”, New J. Phys. 5, 74 (2003).
46. J. E. Allen, “Probe theory – the orbital motion approach”, Phys. Scripta
45, 497 (1992).
47. S. A. Khrapak, A. V. Ivlev, and G. E. Morfill, “Momentum transfer in
complex plasmas”, Phys. Rev. E (2004).
48. V. E. Fortov et al., “Dusty plasmas”, Phys. Usp. 47, 447 (2004).
70
NOTES
71
For information about careers in plasma physics at the US Naval Research
Laboratory, contact us at: PlasmaPhysicsCareers@nrl.navy.mil
This document was typeset using XELATEX. The text and mathematics are set
using the STIX Two fonts, which were created by the Scientific and Technical
Information Exchange (STIX) font creation project. The headings are set in
Frutiger Neue LT Pro, and the monospace text in Inconsolata. The character
for the partial derivative, ∂, is from Charis SIL.
Thomas A. Mehlhorn
Superintendent
Plasma Physics Division
72