Professional Documents
Culture Documents
AUO
G185XW01V2
UP-02-119
The information contained in this document has been carefully researched and is, to the best of our
knowledge, accurate. However, we assume no liability for any product failures or damages, immediate or
consequential, resulting from the use of the information provided herein. Our products are not intended for
use in systems in which failures of product could result in personal injury. All trademarks mentioned herein
are property of their respective owners. All specifications are subject to change without notice.
Product Specification G185XW01 V2
AU OPTRONICS CORPORATION
08
3/
/0
( ) Preliminary Specification
16
( v ) Final Specification
20
On
Module 18.5” Color TFT-LCD
ly
On
se
lU
Customer Date Approved by na Date
er
nt
YI
LA
Approved by Prepared by
DA
or
lF
Athena Wu 2016/03/03
tia
en
id
Contents
08
4.0 Absolute Maximum Ratings ................................................ 12
3/
4.1 TFT LCD Module.............................................................................................................. 12
/0
4.2 Absolute Ratings of Environment ..................................................................................... 12
16
5.0 Electrical characteristics .................................................... 13
20
5.1 TFT LCD Module.............................................................................................................. 13
5.1.1 Power Specification ...................................................................................................... 13
On
5.1.2 Signal Electrical Characteristics.................................................................................... 14
5.2 Backlight Unit ................................................................................................................... 15
ly
6.0 Signal Characteristic .......................................................... 16
On
6.1 Pixel Format Image.......................................................................................................... 16
se
6.2 The input data format....................................................................................................... 17
lU
6.3 Signal Description ............................................................................................................ 18
na
6.4 Timing Characteristics...................................................................................................... 20
er
6.5 Timing diagram ................................................................................................................ 21
nt
9.3 Palletizing......................................................................................................................... 28
lF
11 Safety................................................................................. 31
en
11.2 Materials......................................................................................................................... 31
nf
Record of Revision
Version & Date Page Old description New Description
0.0 2015/01/16 All Preliminary spec
2.1 Display Characteristics 2.1 Display Characteristics
1.0 2015/06/25 5
08
7
3/
/0
16
3.0 Functional Block Diagram 3.0 Functional Block Diagram
20
11
On
4.2 Absolute Ratings of Environment 4.2 Absolute Ratings of Environment
ly
On
se
lU
12
na
er
nt
YI
LA
ISP
7.0 Connector & Pin Assignment 7.0 Connector & Pin Assignment
_D
23
TA
DA
2
7 Central Luminance [cd/m ] Central Luminance [cd/m2]
id
26
08
3/
/0
10.0 Mechanical Characteristics 10.0 Mechanical Characteristics
16
20
1.2 2016/03/03 29
On
ly
On
se
lU
30 na
er
nt
YI
LA
ISP
_D
TA
DA
or
lF
tia
en
id
nf
Co
O
AU
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when
handling.
08
7) Do not open or modify the Module Assembly.
3/
8) Do not press the reflector sheet at the back of the module to any directions.
/0
9) In case if a Module has to be put back into the packing container slot after it was taken out from the
16
container, do not press the center of LED lightbar edge. Instead, press at the far ends of the LED light
bar edge softly. Otherwise the TFT Module may be damaged.
20
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface
On
Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module even
ly
momentarily. While designing the enclosure, it should be taken into consideration that no
On
bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT Module may
be damaged.
se
12) Small amount of materials having no flammability grade is used in the LCD module. The LCD module
lU
should be supplied by power complied with requirements of Limited Power Source (IEC60950-1 or
UL60950-1), or be applied exemption.
na
er
nt
YI
LA
ISP
_D
TA
DA
or
lF
tia
en
id
nf
Co
O
AU
08
ITEMS Unit SPECIFICATIONS
Screen Diagonal [mm] 470.1(18.51”)
3/
Active Area [mm] 409.8 (H) x 230.4 (V)
/0
Pixels H x V 1366(x3) x 768
16
Pixel Pitch [um] 300 (per one triad) × 300
Pixel Arrangement R.G.B. Vertical Stripe
20
Display Mode TN Mode, Normally White
2
[cd/m2]
On
White Luminance ( Center ) 450 cd/m (Typ.)
Contrast Ratio 1000 (Typ.)
Optical Response Time [msec] 5ms (Typ., on/off)
ly
Nominal Input Voltage VDD [Volt] +5.0 V (Typ)
On
Power Consumption
[Watt] 13.5W (Typ.) (Pdd=4.5W, PLED=9W)
(VDD line + LED line)
se
Weight [Grams] 1550(Max)
lU
Physical Size [mm] 430.4 (W) x 254.7 (H) Typ. x 12.7(D)Typ
Electrical Interface One channel LVDS
Support Color na
16.7M colors, RGB 6-bit +Hi- FRC
Surface Treatment Anti-Glare, 3H
er
RoHS Compliance RoHS Compliance
nt
Temperature Range
YI
08
3/
Contrast ratio Normal Direction 600 1000 - 3
/0
16
Raising Time (TrR) - 3.5 5
Response Time [msec] Falling Time (TrF) -
20
1.5 2.5 4
Raising + Falling - 5 7.5
On
Red x 0.583 0.633 0.683
Red y 0.296 0.346 0.396
ly
On
Color / Chromaticity Green x 0.281 0.331 0.381
Coordinates (CIE) Green y 0.550 0.600 0.650
se
5
Blue x 0.098 0.148 0.198
lU
Blue y 0.016 0.066 0.116
White x 0.263 na
0.313 0.363
er
Color Coordinates (CIE) White White y 0.279 0.329 0.379
nt
Flicker dB -20 9
Color Gamut % 68
_D
TA
DA
or
lF
tia
en
id
nf
Co
O
AU
Photo detector
08
3/
/0
16
20
On
Measured distance
ly
On
LCD Panel TFT-LCD Module
se
lU
Center of the screen na
er
nt
Viewing angle is the measurement of contrast ratio ≧10, at the screen center, over a 180° horizontal and
LA
180° vertical range (off-normal viewing angles). The 180° viewing angle range is broken down as follows;
ISP
90° (θ) horizontal left and right and 90° (Φ) vertical, high (up) and low (down). The measurement
direction is typically perpendicular to the display surface with the screen rotated about its center to
_D
% Tr F Tr R
08
3/
100
90
/0
16
Optical
W hite Black Black W hite
response
20
10
0
On
1 Frame 1 Frame
ly
Note 5: Color chromaticity and coordinates (CIE) is measured by TOPCON SR-3
On
Note 6: Central luminance is measured by TOPCON SR-3
se
Note 7: Luminance uniformity of these 9 points is defined as below and measured by TOPCON SR-3
lU
na
er
nt
YI
LA
ISP
_D
TA
DA
or
lF
tia
CT = | YB – YA | / YA × 100 (%)
O
AU
Where
08
3/
/0
16
20
Note 9: Test Patern: Subchecker Pattern measured by TOPCON SR-3
On
RGBRGB
ly
Gray Level = L127
On
RGBRGB
se
Gray Level = L0
lU
RGBRGB
na
er
Method: Record dBV & DC value with TRD-100
nt
YI
Amplitude
LA
AC
ISP
DC
_D
TA
Time
DA
AC Level(at 30 Hz)
Flicker (dB) 20 log
DC Level
or
lF
tia
en
id
nf
Co
O
AU
AUO G1
08
ASIC
3/
Y-Driver IC
Timing
LVDS Controller
TFT-LCD
/0
LVDS Receiver
16
1366(x3) x 768
Connector
RSDS
Pixels
20
Transmitter
+5V X-Driver IC
G768
On
D1 D4098
ly
On
se
Gamma
DC/DC
lU
Correction
Converter
na
er
nt
I/F + X-PCB
YI
DC POWER
LA
LED Driver
ISP
_D
187145-30091-3 (P-TWO)
DA
Mating Type:
117 Series (P-TWO)
or
lF
tia
en
id
nf
Co
O
AU
08
4.2 Absolute Ratings of Environment
3/
/0
Item Symbol Min. Max. Unit Conditions
16
Operating Temperature TOP 0 +60 [oC]
20
Operation Humidity HOP 5 90 [%RH]
Note 3 & 4
On
Storage Temperature TST -20 +60 [oC]
Storage Humidity HST 5 90 [%RH]
ly
On
o
Note 1: With in Ta (25 C)
Note 2: Permanent damage to the device may occur if exceeding maximum values
se
Note 3: For quality perfermance, please refer to AUO IIS(Incoming Inspection Standard).
Note 4: Operation Temperature + 60°C is defined as panel surface termperature.
lU
na
er
nt
YI
LA
ISP
_D
TA
DA
or
lF
tia
en
id
08
Voltage
3/
VDD= 5.0V, All Black Pattern
IDD Input Current - 0.9 1.1 [A]
/0
At 60Hz,
16
VDD= 5.0V, All Black Pattern
PDD VDD Power - 4.5 5.5 [Watt]
At 60Hz
20
On
IRush Inrush Current - - 3 [A] Note 1
ly
Allowable Logic/LCD VDD= 5.0V, All Black Pattern
VDDrp - - 200 [mV] p-p
On
Drive Ripple Voltage At 60Hz
se
Note 1: Measurement conditions:
lU
The duration of rising time of power input is 470us.
+5.0V Q3
AO6402
na
er
D6 F1
D5
D2 S
nt
VCC
D1
47K
G
C1
1uF/16V
LA
(High to Low)
D1
D2
D5
D6
Control
Signal Q3
ISP
R2 AO6402
G
1K
_D
S
C3
2
+12.0V
TA
SW1
SW MAG-SPST VR1 0.01uF/25V
1
47K
DA
C2
1uF/25V
or
lF
tia
en
id
nf
Co
O
AU
08
5.1.2 Signal Electrical Characteristics
3/
Input signals shall be low or Hi-Z state when VDD is off. Please refer to specifications of SN75LVDS82DGG
/0
(Texas Instruments) in detail.
16
20
Characteristics of each signal are as follows:
On
Symbol Parameter Min Typ Max Units Condition
Differential Input High VICM = 1.2V
ly
VTH - +50 +100 [mV]
Threshold Note 1
On
Differential Input Low VICM = 1.2V
VTL -100 -50 - [mV]
Threshold Note 1
se
│VID│ Input Differential Voltage 100 400 600 [mV] Note 1
lU
Differential Input Common VTH-VTL = 200MV (max)
VICM +1.0 +1.2 +1.4 [V]
Mode Voltage na
Note 1
er
Note 1: LVDS Signal Waveform
nt
YI
LA
ISP
V
│VID│
_D
TA
VICM
DA
or
lF
VSS
tia
en
id
nf
Co
O
AU
08
Irush LED Inrush Current - 3 [A] at rising time=470us
3/
Volt
/0
On Control Voltage 3 5 5.5
VLED on/off
16
Off Control Voltage 0.8 Volt
20
Dimming Frequency 200 - 20k [Hz]
On
Swing Voltage 3 3.3 5
ly
Low Voltage 0.8 Volt
On
Dimming Duty Cycle 5 - 100 %
se
o
IF LED Forward Current 50 mA Ta = 25 C
lU
o
VF LED Forward Voltage - 3.2 3.6 Volt IF 50=mA, Ta = 25 C
PLED
LED Power
- 0.18 Watt
na
IF 50=mA, Ta = 25 C
o
er
Consumption
nt
Operation o
50,000 Hrs IF50=mA, Ta= 25 C
Lifetime
YI
Note 2: VCC, Ivcc, PVCC , Irush LED are defined for LED B/L.(100% duty of PWM dimming)
ISP
Note 4: If G185XW01 V2 module is driven by high current or at high ambient temperature & humidity condition. The
TA
Note 5: Operation life means brightness goes down to 50% initial brightness. Minimum operating life time is estimated
data.
or
lF
tia
en
id
nf
Co
O
AU
1 2 1365 1366
1st Line R G B R G B R GB R G B
08
3/
/0
16
20
On
ly
768 Line R G B R G B R GB R G B
On
se
lU
na
er
nt
YI
LA
ISP
_D
TA
DA
or
lF
tia
en
id
nf
Co
O
AU
08
3/
/0
16
20
LVDS Data Mapping of NS Format
On
Note1: Normally, DE, VS, HS on EVEN channel are not used.
Note2: 8-bits signal input.
ly
On
se
lU
na
er
nt
YI
LA
ISP
_D
TA
DA
or
lF
tia
en
id
nf
Co
O
AU
08
2 NC No contact (For AUO internal use)
3/
3 NC No contact (For AUO internal use)
/0
4 GND Power Ground
16
5 RXIN0- Negative LVDS differential data input (0)
20
6 RXIN0+ Positive LVDS differential data input (0)
On
7 GND Power Ground
8 RXIN1- Negative LVDS differential data input (1)
ly
9 RXIN1+ Positive LVDS differential data input (1)
On
10 GND Power Ground
se
11 RXIN2- Negative LVDS differential data input (2)
lU
12 RXIN2+ Positive LVDS differential data input (2)
13
14
GND
RXCLKIN-
Power Ground
Negative LVDS differential clock input (clock)
na
er
nt
08
3/
/0
16
20
On
ly
1 30
On
NC
VDD
se
lU
na
er
nt
YI
08
Blanking Tblk(v) 8 40 255 Th
3/
Period Th 1416 1606 2047 Tclk
/0
H-section Active Tdisp(h) 1366 1366 1366 Tclk
16
Blanking Tblk(h) 50 240 681 Tclk
20
Period Tclk - 12.8 - ns
Clock
On
Frequency Freq - 78 90 MHz
Frame Rate Frame Rate F 50 60 75 Hz
ly
On
Note1 : DE mode only
Note2 : Clock Frequency 90MHz(Max.)= 1416(H)*847(V)*75Hz
se
lU
na
er
nt
YI
LA
ISP
_D
TA
DA
or
lF
tia
en
id
nf
Co
O
AU
08
3/
/0
16
20
On
ly
On
se
lU
na
er
nt
YI
LA
ISP
_D
TA
DA
or
lF
tia
en
id
nf
Co
O
AU
VD 10% 10%
08
Signal
10% 10%
3/
/0
16
90%
90%
VC
20
10% 10%
T8 T9
On
T4 T5
90%
ly
10%
On
T6 T7
se
90%
Back light on/off
lU
10%
T3 T10
na
er
Power ON/OFF sequence timing
nt
Value
YI
Parameter Units
Min. Typ. Max.
LA
T1 0.5 - 10 [ms]
ISP
T2 0 40 50 [ms]
_D
T3 200 - - [ms]
TA
T4 0.5 - 10 [ms]
DA
T5 10 - - [ms]
T6 10 - - [ms]
or
T7 0 - - [ms]
lF
T8 10 - - [ms]
tia
T9 - - 10 [ms]
en
08
Manufacturer P-TWO
3/
Type Part Number 187145-30091-3
/0
Mating Housing Part Number 117 Series
16
20
7.1.1 Pin Assignment
On
Pin# Signal Name Pin# Signal Name
ly
1 NC 2 NC
On
3 NC 4 GND
se
5 RXIN0- 6 RXIN0+
lU
7 GND 8 RXIN1-
9 RXIN1+ 10 GND
11 RXIN2- 12 RXIN2+
na
er
13 GND 14 RXCLKIN-
nt
15 RXCLKIN+ 16 GND
YI
17 RXIN3- 18 RXIN3+
LA
19 GND 20 NC
ISP
21 NC 22 NC
23 GND 24 GND
_D
25 GND 26 VDD
TA
27 VDD 28 VDD
DA
29 VDD 30 VDD
or
lF
08
4 Dimming PWM Dimming
3/
5 NC NC
/0
16
20
On
ly
On
se
lU
na
er
nt
YI
LA
ISP
_D
TA
DA
or
lF
tia
en
id
nf
Co
O
AU
High Temperature Operation (HTO) Tgs= 60oC, 300hours, For panel surface temp. 3&4
08
3/
Low Temperature Operation (LTO) Ta= 0oC, 300hours
/0
o
High Temperature Storage (HTS) Ta= 60 C, 300hours
16
Low Temperature Storage (LTS) Ta= -20oC, 300hours
20
Acceleration: 1.5 Grms
Vibration Test Wave: Random
On
(Non-operation) Frequency: 10 - 200 Hz
Sweep: 30 Minutes each Axis (X, Y, Z)
ly
Acceleration: 50 G
On
Shock Test Wave: Half-sine
(Non-operation) Active Time: 20 ms
se
Direction: ±X, ±Y, ±Z (one time for each Axis)
lU
Drop Test Height: 60 cm, package test
Thermal Shock Test (TST) -20oC /30min, 60oC /30min, 100 cycles na 1
er
On/Off Test On/10sec, Off/10sec, 30,000 cycles
nt
Operation:10,000 ft
_D
Altitude Test
Non-Operation:30,000 ft
TA
Note 1: The TFT-LCD module will not sustain damage after being subjected to 100 cycles of rapid
DA
temperature change. A cycle of rapid temperature change consists of varying the temperature from -20oC to
60oC, and back again. Power is not applied during the test. After temperature cycling, the unit is placed in
or
Note 2: According to EN61000-4-2 , ESD class B: Some performance degradation allowed. No data lost.
Self-recoverable. No hardware failures.
tia
Note 4: No function occurs Mura shall be ignored after high temperature reliability test.
id
nf
Co
O
AU
08
3/
/0
16
20
On
ly
On
Note 1: For Pb Free products, AUO will add for identification.
se
Note 2: For RoHS compatible products, AUO will add for identification.
lU
Note 3: For China RoHS compatible products, AUO will add for identification.
na
Note 4: The Green Mark will be presented only when the green documents have been ready by AUO
er
Internal Green Team.
nt
YI
LA
ISP
_D
TA
DA
or
lF
tia
en
id
nf
Co
O
AU
9.2 Packaging
08
3/
/0
16
20
On
ly
On
se
Max capacity:8 TFT-LCD module per carton
lU
Max weight: 15.0 kg per carton
Outside dimension of carton: 520mm(L)* 280mm(W)*352mm(H) na
er
Pallet size: 1140 mm *1060 mm * 135mm
nt
YI
Box stacked
LA
ISP
By sea_HQ_max:(2 *4) *4 layers+(2 *4) *2 layers, two pallet put 48 boxes, total 384pcs module
TA
DA
or
lF
tia
en
id
nf
Co
O
AU
/0
G185XW01 V2
16
AU OPTRONICS CORPORATION
20
On
9.3 Palletizing
nly
O
se
lU
na
er
nt
YI
LA
SP
DI
A_
AT
rD
Fo
t ial
en
id
nf
Co
/0
G185XW01 V2
16
AU OPTRONICS CORPORATION
20
10.0 Mechanical Characteristics
On
nly
O
se
lU
na
er
nt
YI
LA
SP
DI
A_
AT
rD
Fo
t ial
en
id
nf
Co
/0
G185XW01 V2
16
AU OPTRONICS CORPORATION
20
On
nly
O
se
lU
na
er
nt
YI
LA
SP
DI
A_
AT
rD
Fo
t ial
en
id
nf
Co
11.2 Materials
11.2.1 Toxicity
There will be no carcinogenic materials used anywhere in the display module. If toxic materials are
used, they will be reviewed and approved by the responsible AUO toxicologist.
11.2.2 Flammability
08
All components including electrical components that do not meet the flammability grade UL94-V1 in the
3/
module will complete the flammability rating exception approval process.
/0
The printed circuit board will be made from material rated 94-V1 or better. The actual UL flammability
16
rating will be printed on the printed circuit board.
20
On
11.3 Capacitors
If any polarized capacitors are used in the display assembly, provisions will be made to keep them from
ly
being inserted backwards.
On
11.4 National Test Lab Requirement
se
The display module will satisfy all requirements for compliance to:
lU
UL 60950-1, Second Edition na
U.S.A. Information Technology Equipment
er
nt
YI
LA
ISP
_D
TA
DA
or
lF
tia
en
id
nf
Co
O
AU
Headquarters
Switzerland ALTRAC AG
Bahnhofstraße 3
5436 Würenlos