Professional Documents
Culture Documents
ffi
Do not po1,1r water 01141r tha product. The w111..r m111y•nt$r,which may cause, d111m111g• to the d•vlces.
::S::::-.X----
T111rm1 n als
Timper twitch , .
� lntallation Way
Pcec•-
o,,. 5
Wall mounting
Zona modu1a(Opt lon•I)
r:-'
Wlrln11 holas
(i:Mount ona s olld aurfaca, ®Do not in•tall the unit where objectt ®Prevont direct au nli11hl or l ight from ont ar ing
d o not I nsta l on u n steadys urfaca. moved byth e wind 1uch 1e pl111nta 1nd intopruduclint orn•I.
l
laundry, which may block th e beam.
� l �ront case
lllsto C 1.Loosencover lock ,cnw, 2.Pull ou t wlr11 from mounting hole ,
2 Beams Front Case 2BeamsBase 2BeamsBody remova front cov er keepWlr11 aa 10cm forc:onn ectlng
Terminal•
©Avoid the tMiem rrom other ®Avoid aertal wiring. @.P1.a1e 1 n1tall lhe detector awayfrom well
detee1otS entering the r.eelve,r. orfenC6 at th• dlatanc e or more than , m.
2beams150rnelall 160m 2 4m
. 3beenB2llO- 200m 3.4m 3.Put expansio n pipe Into 4 mounn ng holN, 4.Connact wire and beam 1llgnm11nt 5.Check oper tion,cover the e&ff and
Fro nt caae h nx themWith acN!IW (Pl eaH refar to "opUcal ula ananment") fa,ten ecrew .
� a screw
t en
rr
Pole Mounting
DIP Switch
Wiring hol e
1 set wiring: 2 sets wiring:
��!0
�)
The power of transmitte r and reoelve r are parallele d, The power of th e trans mitter and receiver are pani lle led
'/ u1lng DC 12V b ycontrol pan el, alarm output 11 NC •• below: connectio n u, 1i ng DC 12V bycontrol pe nel,ala nn out put 1..1 �:.=�:i"b� �h:::.!i° !::'��!�i:.�:d:!iver.
i• NC a nd seriHconnect ion •• below: � ln ea or,
d t 51,pl a aetll
afterdebu e se
1 ! 5 1 ���Ff:1!:�':�=�� l
� .
� .- -1.-1.-1.-1.- 1.-1
Brocket outer dlamater f 1 Lili�� � �FF�t �L [:] �::���!;!���·�n��j:��\���::��:=:�1f:�1tomar
ct>3&-'ASOmm ____
O
N � [:l;Jam [;)oH [;rehHt [;Jw s e t t 11
s,- {�)Th:t��!:it��::� �::a�: �.:l=: ��::: h:h��7Y·
1
1.Pull oulwire from 1tend 2.Re move h'ont cover 3.Pull ou tWire rrom mountin g hole, � low, c:en beaat aocorcllngto alarm dl1tance.
keep wlf'l!ll aa tocmhtrconn ectlng Transmitter � R,,mn lng lndlCllllhlr a..m power
Beam frequency
J1; ii�
4"601111
(1)CIP swltc:h 1 and2 used for Htt lng beam frequency,
U1hape bracleat the positio n must b a tha aeme for t111n1mltter a nd recel....r.
(2)Tninamltter running In dicator, after debug, pleue sal It
HOFF, a nd set dlgltal tube •• OFF to saveenar;y.
(3)Preheat funct ion ulecl fortest:ln si heetlnsi funetlon, the
q
oonatant tempeniture con trol I• higher than heet lng.
(4)1 nterruption time n111111d to chooH aec:ordlngto ln.lallatlon plae..
(5)Eaeh in terruption time HI•• the maximum d111lecta ble lime.
Fe ,te repeed maybe not d111lected. To b irds,new.papar,laavHel"c:,
theyca n i nterrupt beam oc:ca, ionally,Htling lo nger intarrup tion time.
811 J
Afler adjust:inlil int erruption time, verify ia need111d.
2 88la of 1ertN ln ste llatlon:The power of th e trans mitter and receiver are peni lle lad c:onnecllon,
Beam frequency ln tarrupt lontlm e
4. F lx2 be111m1 sensor to the •ta n 5.2 beams 11en11or inatall back to back ualng DC 12V bycontrol panel,alarm output Is NC and aerie, c:on nectlon.
• The wire length between power aupply and datacto rshould not exceed as balow: A caution
jfl
U•hape bracket
CC12V DC2-4V
DI��-
Alignement Indicator
Q 0.5mm• (Dlameter0.8) 100m 500m 1.Powerwira Hn noloxceed the li1ted lanuth.
f-------+-------+----------i 2.Wh11nconnactmorede tectora,theneeded
f------�t-
0.76mm• (Dl11met11 1.0)
r
------+---------i
15Dm wire l ength ie obtai ned byliated len gth divided
750m
byn umber ofunit-.u1ed.
Q
- - --- 1
1.0mm• (Dlamater 1.2 ) 2oom 1000m 3.Do not connec:tterminal• loexceed voltage
spec: ified ,dl)jng eo mi11ht damage device or ca.u1111 Digital tube indicator
1 .Smm" (Diam eter 1.4) 250m 12som fire.
Receiver terminals:
I .Power Input DC 10V-24V
2.0p tlonal heater, standard without hea tar
3.Re layc:onta<:t 1C 30VDC 0.6A.mu:
o...... Reallgn
Sl9na l 1trength 5...gQenar11I
7-BGcod
Tra nsmitter Receiver COM NO NC BPARE HEATER gEJtcellent