Professional Documents
Culture Documents
1
June 2004
Model VIS
Discharge
Bowl and
Column
Adapter
Bowl
Assembly
Suction
Adapter
Submersible
Motor
2
Flanged Column
Column sections are provided with flanged ends incorporating registered fits for ease
of alignment during assembly. Facilitates disassembly where corrosion is a problem.
Our standard bearing retainers are welded into the column section.
3
Coupling Arrangements
RIGID FLANGED COUPLING (Type AR) ADJUSTABLE COUPLING (Type A) ADJUSTABLE SPACER COUPLING
To couple pump to vertical hollow shaft driver. For vertical solid shaft driver. Impeller (Type AS)
Impeller adjustment is performed on adjusting adjustment made by using adjustable Same function as type A coupling with
nut located on top of motor. plate in the coupling. addition of spacer. Spacer may be removed
for mechanical seal maintenance without
disturbing driver.
Discharge Heads
The discharge head functions to change the direction of flow from vertical to
horizontal and to couple the pump to the system piping in addition to supporting
and aligning the driver. Discharge head accommodates all modes of drivers
including hollow shaft and solid shaft motors, right angle gears, vertical steam
turbines, etc. Optional sub-base can be supplied. Goulds offers three basic
types for maximum flexibility.
4
Model VIT-FF
Vertical Industrial
Turbine Pump
■ Capacities to 65,000 GPM (14,763 m3/h)
■ Heads to 3,500 feet (1,067m)
■ Temperatures to 500° F (260° C)
■ Bowl sizes from 6” to 55”
Design Advantages
• Fabricated discharge head and flanged column.
• Flanged bowl construction.
• 416SS shafting.
• Alloy construction with external flush of critical wear
areas available for corrosive/abrasive services.
• Built-in alignment and simple piping for less
costly installation and ease of maintenance/
reduced downtime.
Services
Cooling Water
Seawater and River Water Intake
Industrial Process Pumps
Utility Circulating Water
Condenser Circulating Water Pumps
Ash Sluice
5
Cross Sectional
VIT-FF (Product Lube) VSS Motor
Mounting Holes
Capscrew - Col/Col
Hex Nut
Column - Intermediate
Lineshaft
Bearing - Lineshaft
Column - Bottom
Coupling - Lineshaft
Pumpshaft
Sand Collar
Capscrew - Bowl/Bell
Bearing - Suction
Capscrew - Strainer
Pipe Plug Strainer (Basket Type)
Suction
VIT OpenBell
6
Cross Sectional VSS Motor
VIC-T
Motor Key
(Supplied By Motor Vendor)
Typical Markets Served Hub - Driver
Ring - Retaining
■ Power Generation
Capscrew Motor/Support Soc. HD. Capscrew/
■ Chemical
Hex Nut
■ Hydrocarbon Processing
■ General Industry Motor Support Spacer
Coupling Guard Soc. HD. Capscrew/
Gland Hex Nut
Soc. HD. Capscrew - Gland/Housing Plate - Adjusting
Soc. HD. Capscrew - Housing/Head Key- Pump
Capscrew - Support/Head Hub - Pump
Headshaft
O-ring
Capscrew - Col./Head
Column - Top
Capscrew - Col./Col.
Hex Nut
Retainer-BRG.
Column - Intermediate
Lineshaft
Retainer - Bearing
Bearing - Lineshaft
Column - Bottom
Coupling - Lineshaft
Pumpshaft
Impeller
Wear Ring - Bowl (Optional) Capscrew - Bowl/Bowl
Wear Ring - Imp. (Optional)
Bowl - INTMD.
Taper Lock
Capscrew - Bowl/Bell
Bearing - Suction
Suction Bell
Barrel
VIC Commercial 7
Cross Sectional
(3.1.4) Motor
Horsepower Margin
(3.1.5) Motor Design
Required to API-541?
VIC-T (Per API-610 8th edition) (3.1.7A) Motor Thrust
Bearing Life
(3.1.7B) Motor Thrust
Bearing Lift
Typical Markets Served (1.1.4) IS API-610 8th
Ed. Required? (3.1.7C) Motor Thrust
■ Hydrocarbon Processing Bearing Location
(3.3.7.3.4) Motor
■ Chemical Alignment Screws (3.1.8) Motor to be VSS
■ General Industry as Required (5.3.7.1.1) Motor-
(2.5.4 1) 16” Thread Fabricated Frame Requires
Clearance on 1-1/2” Post-Weld Stress Relief
and Greater (3.2.7) Coupling Will be
Balanced as Assembly
(2.1.7) Auxiliary Sealing Required for Condensate Application
(5.3.7.2) Precision
(2.2.1.3.4) Studs and Nuts at Sealing Housing Coupling As Required
(2.3.3.4) Socket Welded
(2.7.1) Mechanical Seal Required
Piping Plan Required By
(2.7.2) Mechanical Seal to API-682? Special Service
(2.7.3.2) Balanced Mechanical Seal (2.11.3.5.6) NDE of
(2.7.3.1.6) Additional Seal and Gland Vent Tap Nozzle Welds
(2.7.3.2.0) Throttle Bushing Required Except Tandem (2.7.3.9) Steel
Seal Housing
(2.2.1) Pressure Boundary Components to ASME Section VIII & IX (2.2.8) Nozzle Load
(2.2.2.b) 300” Flange Rating (Standard) 1 x API (Standard)
(2.2.3) 1/8” Corrosion Allowance (2.4) “
(2.4.3) “
(5.3.7.3.1) Can Mounting Flange is Required (2.11.3.4.4) Post Weld
Heat Treatment Required
on Carbon Steel Fabs
(5.3.7.3.5) Separate Sub
Base as Required
(5.3.2.3) One Piece Shaft
as Required (As allowed
by TPL)
(5.3.5.1) Bearing Spacing as Required
(2.2.13.3) Corrosion
Resistant Bolting (Typical)
Testing Notes
2.8.3.2 If vibration test is required,
pump is to be fully tested
w/job motor.
(2.5.2) Keyed Impellers (Standard)
2.11.1.7 CMTR’s are only required
(2.1.4) Is higher Capacity Impeller Available? if required by customer.
(2.8.4.1) Impeller Dynamically Balanced to 4W/N 4.1.3 Observed testing is
considered witness.
4.1.4 Customer is to define
(2.6.1) Bowl and Impeller Wear Ring Required inspection requirements.
(2.6.2) Set Screw Wear Rings 4.2.2.1 Customer is to define
(2.6.3) Different Hardness Required (By Material) NDE requirements.
4.3.2.1 & Hydro testing
4.3.2.6 as required.
4.3.3 Performance testing
as required.
8
Hydraulic Coverage for models VIT, VIC and VIS
CAPACITY – m3/h CAPACITY – m3/h
HEAD –FEET
30
HEAD –FEET
70 20
70
20
50 16
50 16
40 12
40 12
30
30
8
8
20 20 6
6
4 4
0 10
20 100 300 500 1000 2000 3000 20 100 400 1000 4000 10000 20000
CAPACITY –GPM CAPACITY – GPM
200 400 600 1000 2000 3000 5000 200 400 600 1000 2000 3000 5000
300 200
50
200 150
40
1180 R.P.M. 50 880 R.P.M.
1500
40 100 30
20
HEAD –FEET
HEAD –FEET
60
20 50 16
60
50 16
40 12
40 12
30
30 8
8
20 6
20 6
4 4
1000 3000 10000 20000 40000 1000 3000 10000 20000 40000
CAPACITY – GPM CAPACITY – GPM
400 600 1000 2000 3000 5000 8000 10000 15000 400 600 1000 2000 3000 5000 8000 10000 15000
200 200
50 50
150 150
40 40
710 R.P.M. 590 R.P.M.
100 30 100 30
80
HEAD –FEET
20 20
HEAD –FEET
60 60
50 16 50 16
40 12 40 12
30 30
8 8
20 6 20 6
4 4
3000 5000 10000 20000 30000 100000 3000 5000 10000 20000 40000 100000
CAPACITY – GPM CAPACITY – GPM
600 1000 2000 3000 5000 8000 10000 15000 20000 600 1000 2000 3000 5000 8000 10000 15000 20000 30000
200 200
50 50
150 150
40 40
500 R.P.M. 440 R.P.M.
100 30 100 30
TOTAL HEAD – METERS
80 80
20
HEAD –FEET
HEAD –FEET
20
60 60
50 16 50 16
40 12 40 12
30 30
8 8
20 6 20 6
4 4
2000 4000 10000 30000 50000 100000 150000 2000 2000 6000 10000 20000 50000 100000 150000
CAPACITY – GPM CAPACITY – GPM
RANGE CHART
25 90
DESIGN OPTIONS AND FEATURES PROVIDE
IMPORTANT COST SAVINGS BENEFITS 80
Available as an option on all ITT A-C Pump wet-pit 20
WCB
70
pumps, the “pullout” design reduces maintenance
TDH- Meters
60
remains undisturbed when removing the pump.
15
The unique hydraulic thrust relief design (achieved 50
WCA
by opening an area behind the impeller to the
40
outside of the pump) results in low thrust values 10
from maximum flow to shutoff head. This reduces 30
the cost of the driver by reducing the size of the YDD
required thrust bearing. 5 20
To reach high pressure heads the pumps can be WCAX
3 10
arranged for up to a three stage configuration. ITT 0 100 200 300 400
A-C Pump’s advanced hydraulic designs provide
Capacity in 1,000 U.S. GPM
some of the highest efficiency pumps available in
the pumping industry. 0 20 40 60 80 90
Capacity in 1,000 Cubic Meters Per Hour
10
Model WMCC-WMCE
RANGE CHART
175 600
125
TDH- Meters
400
TDH-Feet
100 WMCC-
300 WMCE-2 Stage 3 Stage
75
200 WMCC-
50 WMCE-1 Stage 2 Stage
100
WCAX
15 50
0 50 100 150 200 250
Capacity in 1,000 U.S. GPM
0 10 20 30 40 50
Capacity in 1,000 Cubic Meters Per Hour
11
Cross Sectional
VIS Bowl Disch.
Discharge
Typical Markets Served
■ General Industry Bearing - Suction/Disch.
■ Municipal
■ Hydrocarbon Processing Sand Collar
Bowl INTMD.
Bearing INTMD.
Taper Lock
Impeller
Pumpshaft
Screen Suction
Suction
Bearing - Suction/Disch.
Coupling
Adapter SBM
Submersible Motor
VIS
12
Model VIS
Vertical Industrial
Submersible Pump
■ Capacities to 4,000 GPM (908 m3/h)
■ Heads to 1,400 feet (427m)
■ Bowl sizes from 6” to 20”
Design Advantages
• Ideal for deep set applications where use of lineshaft
pumps is impractical.
• Complete unit is installed underground resulting in
quiet operation and space saving.
• Long life/low maintenance — no lubrication, alignment.
Services
Irrigation
Service Water
Deep Well
13
Model VIC
Vertical Industrial
Can-Type Pump
■ Capacities to 65,000 GPM (14,763 m3/h)
■ Heads to 3,500 feet (1,070m)
■ Temperatures cryogenic to 500° F (260° C)
■ Bowl sizes from 6” to 55”
Design Advantages
• Fabricated discharge head.
• Flanged bowl construction.
• 416SS shafting.
• In-line suction and discharge simplifies installation.
• Optional suction in can for flexibility.
• Inherent design features on Model VIC allow efficient
operation at any NPSH available.
• Alloy construction for corrosive/abrasive services.
• Refer to pages 5 and 6 for additional bowl assembly
features/options.
Services
Pipeline Booster
Product Unloading, Refinery Blending
Injection-Secondary Recovery
Ammonia Transfer
Boiler Feed
Condensate
Cryogenics
LNG Transfer
14
Cross Sectional
VIT-FF (Enclosed Lineshaft) VSS Motor
Motor Key
(Supplied By Motor Vendor)
Typical Markets Served
Capscrew Hub - Motor
■ Mining Ring - Retaining
(Motor/Support)
■ Municipal Soc. HD. Capscrew
■ Power Generation Motor Support Plate - Adjusting
Coupling Guard Hex Nut
■ General Industry Hub - Pump
■ Chemical Capscrew Support/Head Pump Key
Tension Plate
• Oil Lube
• Water Flush Pipe Plug
Head
Mounting Holes
Tube Nipple
Capscrew Col./HD.
Headshaft
Column - Top
Tube - Encl.
Bearing - Tube
Column - INTMD
Capscrew - Col./Col.
Tube Stabilizer
(Not shown)
Supplied every 40 ft.
Hex Nut
Lineshaft
Column - Bottom
Coupling - Lineshaft
Adapter - Bearing
Capscrew - Col./Bowl
16
Sealing Flexibility
PACKED BOX WITH SLEEVE WATER FLUSH ENCLOSED LINESHAFT OIL LUBRICATED ENCLOSED LINESHAFT
OPEN LINESHAFT Water flush tube connection is supplied Oil lubricated option is recommended when
Whenever packing lubrication leakage can be when pressurized water is introduced into water elevation would cause the upper lineshaft
tolerated and the discharge pressure does not the enclosing tube for bearing protection on bearings to run without lubrication during start-
exceed 150 psi, a packed box may be used. abrasive services. up. Oil is fed through tapped opening and
Optional headshaft sleeve available to allowed to gravitate down enclosing tube
protect shaft. lubricating bearings.
17
Pump Bowl Assembly Options
Open
Closed
18
Pump Bowl Assembly
The bowl assembly is the heart of the vertical turbine pump. The impeller and
diffuser type casing are designed to deliver the head and capacity that your system
requires in the most efficient way possible. The fact that the vertical turbine pump can
be multi-staged allows maximum flexibility both in the initial pump selection and in the
event that future system modifications require a change in the pump rating.
Submerged impellers allow pump to be started without priming.
A variety of material options allows the selection of a pump best suited for even the
most severe services. The many bowl assembly options available assure that the
vertical turbine pump satisfies the users’ needs for safe, efficient, reliable and
maintenance-free operation.
19
Pick Your Perfect Process Pump
No one in the industry offers the broad range
of process pumps that Goulds does...
Whether it’s for pumping severe corrosives,
abrasive slurries, fibrous/stringy solids, high
temperature liquids, hazardous fluids, low
flow or high capacity services – Goulds has
a perfect, reliable solution. The Goulds
selection of pump solutions includes
horizontal and vertical configurations
in a range of alloy and non-metallic
constructions, sealed and sealless.
Your local PRO Service Center offers high quality repair/rebowling capability for your
vertical turbine pumps. They’re experienced with pumps of all manufacturers – including
Aurora, Byron-Jackson, Floway, Goulds, A-C, Ingersoll-Rand, Johnston and Peerless –
among a range of others.
Experienced PRO technicians are equipped with the latest technology and training.
They provide full factory engineering support for failure analysis, material upgrade and
performance enhancements.
PRO Service Centers provide a thorough inspection and as found report. A complete
workscope for all required repairs with a firm price are included. We’re capable of
handling all critical work such as non-destructive testing, welding and machining.