Professional Documents
Culture Documents
GRNCF - 95° Thick Door
GRNCF - 95° Thick Door
ORDER INFORMATION
Material Item No.
with
Door overlay View Cranking Click-on
Cup Arm spring
Screw fixing
Steel, Zamak,
Full overlay 0 ■ F015072820
nickel-plated nickel-plated
Steel, Zamak,
Half overlay 8 ■ F015072822
nickel-plated nickel-plated
Steel, Zamak,
Inset 15 ■ F015072823
nickel-plated nickel-plated
COVER CAPS
Designation Cranking Imprinted/Embossed Item No.
Hinge arm cover cap, steel, short, nickel-plated, not imprinted,
0 On request F069073570
Soft-close compatible
ACCESSORIES
Designation Item No. Designation Item No.
Nexis Click-on mounting plates 216 Soft-close Pin 290 Assembly aids 358
Accessories 224 Technical information 226
182 Packaging units are not covered in this brochure; please enquire with your supplier
Hinge systems
Nexis Click-on 25
64
65
3-6
3-11 3-11
Tiomos
F 2xF F
18 11 F
26 3
35 6
Nexis
3 4 5 6 7 8 9 10 11 3 4 5 6 7 8 9 10 11 3 4 5 6
23 0 15 0 0 2 3 4
22 0 2 14 0 2 1 2 3 4
21 0 2 3 13 0 2 3 2 3 4
20 0 2 3 4 12 0 2 3 4
19 0 2 3 4 11 0 2 3 4
18 0 2 3 4 10 0 2 3 4
Special
hinges
17 0 2 3 4 9 0 2 3 4
16 0 2 3 4 8 0 2 3 4
Door overlay
Door overlay
Door reveal
15 2 3 4 7 2 3 4
14 2 3 4 6 2 3 4
13 3 4 5 3 4
Mounting plate height Mounting plate height Mounting plate height
Single-joint
MINIMUM GAP MINIMUM REVEAL NOTES
hinges
Cup distance Cup distance The minimum gap is the clearance
3 4 5 6 8 10 3 4 5 6 8 10 required between the front edge of the
20 0.0 0.0 0.0 0.0 0.0 0.0 20 0.1 0.1 0.1 0.1 0.1 0.1 cabinet and the closed door so that the
22 0.0 0.0 0.0 0.0 0.0 0.0 22 0.2 0.2 0.2 0.2 0.2 0.2 door can open without hindrance.
24 0.0 0.0 0.0 0.0 0.0 0.0 24 0.3 0.3 0.3 0.3 0.3 0.3
Cabinet making
Important: Reveals were calculated
accessories
26 0.0 0.0 0.0 0.0 0.0 0.0 26 0.4 0.4 0.4 0.4 0.4 0.4
for doors with a radius of 1 mm!
28 0.0 0.0 0.0 0.0 0.0 0.0 28 0.6 0.6 0.6 0.6 0.6 0.6
Door thickness
Door thickness
30 0.0 0.0 0.0 0.0 0.0 0.0 30 0.8 0.8 0.8 0.8 0.8 0.8 Hinge dimensions and reveal calculation
32 0.0 0.0 0.0 0.0 0.0 0.0 32 2.1 1.1 1.1 1.1 1.1 1.1 with factory setting.
34 0.0 0.0 0.0 0.0 0.0 0.0 34 4.2 3.1 2.3 1.6 1.4 1.4 We recommend a trial fitting.
36 0.0 0.0 0.0 0.0 0.0 0.0 36 6.5 5.2 4.2 3.5 2.2 1.7
Minimum gap Minimum reveal (F)