Professional Documents
Culture Documents
2008″
1. Which of the following most nearly gives the vertical reaction at A in KiloNewtons:
A. 31
B. 36
C. 28
D. 23
2. Which of the following most nearly gives the total reaction at the hinge in KiloNewtons:
A. 45.2
B. 85.6
C. 54.1
D. 32.3
3. Which of the following most nearly gives the total reaction at B in KiloNewtons:
A. 32.3
B. 45.2
C. 85.6
D. 54.1
Solution:
Design and Construction “CE Board Exam Nov. 2008″
Concrete beam 8meters long and spaced 4m center-to-center are used to support a concrete slab 115 mm thick.
The beams have effective depth of 650 mm measured from the slab surface, b w=300mm, and are reinforced for
tension only with six 28-mm-diameter bars. The beams are to be analyzed as T-beams. Steel yield strength
fy=350MPa and concrete strength fc=21MPa.
1. Which of the following most nearly give the width of slab effective as T-beam, in millimeters?
A. 2000
B. 2140
C. 4000
D. 3250
2. Which of the following most nearly give the depth of compression block in millimeters?
A. 36.2
B. 45.2
C. 56.3
D. 62.4
3. Which of the following most nearly give the nominal moment capacity of the beam in KiloNewton-Meter.
A. 563
B. 784
C. 952
D. 817
SOLUTION
Steel column 3.6m long and hinged at both ends is used to carry an axial load of 800kN. The column is subject to end
moments about its strong axis (single curvature) with M1 = 90%M2. The frame is braced against joint translation and
is not subjected to any transverse loading. Fy =248MPa, E=200GPa.
The properties of the section are as follows:
A=0.013 m2 rb=94 mm
Sx=0.00099 m2 K=1.0
1. Which of the following most nearly gives the computed (actual) axial stress of the column in MegaPascals.
A. 57
B. 75
C. 62
D. 68
2. Which of the following most nearly gives the allowable axial compressive stress of the column in MegaPascals.
A. 114
B. 120
C. 133
D. 148
3. From a separate calculation with Fb = 149MPa, which of the following most nearly gives the maximum moment
that the column can carry, in KiloNewton-Meter.
A. 85.6
B. 75.4
C. 71.4
D. 78.8
SOLUTION
Design and Construction “CE Board Exam Nov. 2008″
June 9th, 2010 admin No comments
The implementing rules of PD 1594 defines an unbalanced bi as a bid containing one or more pay items that are 30%
higher than the unit allowable government estimate (AGE) in respect to major items whereas other pay items are
priced lower than the unit AGE. AGE is defined as one-half the sum of the AAE and the average of all responsive bids.
For purposes of determining the average of all responsive bids, bids higher than 120% of the AAE or lower than 60%
of the AAE shall not be considered. Major items are defined as pay items representing at least 20% of the AAE or
those indicated or specified in the instruction to bidders. The responsive bids for a government project with 8 bid
items are as follows (all cost figures are in thousands of pesos):
Qty Total AAE Bidder A Bidder B Bidder C
Item 1 100 1,000 1,000 1,250 750
Item 2 100 20,000 22,000 16,000 19,000
Item 3 500 5,000 4,000 6,100 5,100
Item 4 60 6,000 6,000 4,800 5,600
Item 5 1,000 3,000 2,900 3,300 2,800
Item 6 400 1,600 1,000 1,600 2,100
Item 7 3,000 3,000 2,500 2,400 3,200
Item 8 20 25,000 31,000 20,000 26,000
1. Which of the following most nearly gives the total AAE in thousand pesos:
A. 64,600
B. 54,800
C. 48,000
D. 71,000
2. Which of the following give the complete list of major item?
A. Item 8
B. Items 2,4 & 8
C. Items 2,3,4, & 8
D. Items 2 & 8
3. Which of the following gives the complete list of unbalanced bids?
A. Bidders A, B, C
B. Bidders A, C
C. Bidders A
D. All are balanced bids
Solution:
Ave. of AGE 130% of
Item Qty AAE Bidder A Bidder B Bidder C
responsive bids AGE
1 100 1,000 1,000 1,250 750 875 937.50
2 100 20,000 22,000 16,000 19,000 19000 19500 25,350
3 500 5,000 4,000 6,100 5,100 4550 4775
4 60 6,000 6,000 4,800 5,600 5467 5733.3
5 1,000 3,000 2,900 3,300 2,800 3000 3000
6 400 1,600 1,000 1,600 2,100 1300 1450
7 3,000 3,000 2,500 2,400 3,200 2700 2850
8 20 25,000 31,000 20,000 26,000 23000 24000 31200
Note: bids inside shaded boxes are not responsive bids.
Unbalanced bids are those with bids higher than 130% of the AGE in respect to major items, while other items are
priced lower than the unit AGE.
Since no bid goes higher than 130% of AGE for items 2 & 8 (which are the major items), all bids are balance.
1. Which of the following most nearly gives the area in square units?
A. 2330
B. 2130
C. 2230
D. 2030
2. Which of the following most nearly gives the location of the centroid of the area from the y-axis?
A. 52
B. 48
C. 42
D. 58
3. Which of the following most nearly gives the location of the centroid of the area from the x-axis?
A. 20
B. 10
C. 15
D. 25
Solution:
A 4-m single span beam having a cross-section of 300mm x 500 mm carries a uniformly distributed load throughout
its span. The beam is 80% stress grade Apitong with allowable bending stress of 16.5 MegaPascals, allowable shearing
stress of 1.73 MPa and modulus of elasticity of 7.31 GigaPascals. Allowable deflection is 1/240 of the span.
1. Which of the following most nearly gives the value of the uniform load without exceeding the allowable bending
stress of the beam, in KiloNewton per Meter.
A. 118
B. 103
C. 132
D. 124
2. Which of the following most nearly gives the value of the uniform load without exceeding the allowable shearing
stress of the beam, in KiloNewton per Meter.
A. 63
B. 54
C. 87
D. 75
3. Which of the following most nearly gives the value of the uniform load without exceeding the allowable
deflection, in KiloNewton per Meter.
A. 102
B. 98
C. 124
D. 114
Solution:
1. Compute for the effective pressure the mid height of the consolidating clay layer, in kPa.
A. 186.4
B. 174.8
C. 147.6
D. 163.5
2. Compute for the compression index of the clay.
A. 0.297
B. 0.245
C. 0.325
D. 0.288
3. What is the approximate settlement of the foundation?
A. 150 mm
B. 168 mm
C. 214 mm
D. 198 mm
Solution:
Hydraulics “CE Board Exam Nov. 2008″
A test is set-up as shown. A cylindrical mold 4” in diameter is filled with silt to height H 1 = 0.2 ft, whose coefficient of
permeability k1 = 6.1 x 10-4 ft/min.
A second coaxial mold is placed on top of the first mold whose inside diameter is d=1.5” and whose height is H 2 = 0.30
ft. Its thickness is negligible. The inside of this second mold is filled with the same silt, but the annular ring outside the
small tube and outer tube is filled with sand whose coefficient of permeability is k 2 = 2.5 x 10-3 ft/min.The test set-up
is a permeameter of constant head. Water is placed in the mold and maintained at a level h=1.4ft. above the level of
the outlet. It may be considered that the system consists of a fictitious soil of thickness H=H 1 + H2 and coefficient of
permeability kf.
The following general equations may be useful:
kv eq = H/[(H1/kv1) + (H2/kv2) + … + (Hn/kvn)]
kv eq = (1/H)[kh1H1 + kh2H2 + … + khnHn]
1. What is the total flow of water in ft3/min?
A. 2.148 x 10-4
B. 3.521 x 10-4
C. 2.554 x 10-4
D. 2.874 x 10-4
2. What is the equivalent coefficient of permeability, k f, in ft/min?
A. 1.045 x 10-3
B. 1.563 x 10-3
C. 1.874 x 10-3
D. 1.245 x 10-3
3. What is the total amount of water that percolated after 30minutes?D. 325.32 cm 3
A. 217.12 cm3
B. 187.54 cm3
C. 256.32 cm3
D. 325.32 cm3
Solution:
Solution:
Hydraulics “CE Board Exam Nov. 2008″
A triaxial test was conducted on a cohesionless soil. At failure plane, the normal stress is 500kPa and the shearing
stress is 300kPa.
1. What is the nearest value to the angle of internal friction of the soil?
A. 31°
B. 33°
C. 29°
D. 27°
2. What is the nearest value to the angle of failure plane?
A. 60.5°
B. 62.5°
C. 58.5°
D. 59.5°
3. What is the nearest value to the maximum principal stress in kPa?
A. 1280
B. 1240
C. 1030
D. 1150
Solution:
Hydraulics “CE Board Exam Nov. 2008″
An open-top cylindrical tank 1 meter in diameter is 2.80m tall. The tank floats in water with a draft of 2.30 meters.
Unit weight of lead is 110 kN/m3.
1. What is the weight of tank in KiloNewtons?
A. 19.54
B. 21.57
C. 15.24
D. 17.72
2. How much lead (in KiloNewtons) must be fastened to the outside bottom of the tank in order make it completely
submerged in water?
A. 100m
B. 120m
C. 150m
D. 80m
3. How much lead (in KiloNewtons) must be place inside the tank in order make it completely submerged in water?
A. 4.87
B. 4.21
C. 3.85
D. 3.24
Design and Construction “CE Board Exam Nov. 2008″
The implementing rules of PD 1594 defines an unbalanced bi as a bid containing one or more pay items that are 30%
higher than the unit allowable government estimate (AGE) in respect to major items whereas other pay items are
priced lower than the unit AGE. AGE is defined as one-half the sum of the AAE and the average of all responsive bids.
For purposes of determining the average of all responsive bids, bids higher than 120% of the AAE or lower than 60%
of the AAE shall not be considered. Major items are defined as pay items representing at least 20% of the AAE or
those indicated or specified in the instruction to bidders. The responsive bids for a government project with 8 bid
items are as follows (all cost figures are in thousands of pesos):
Qty Total AAE Bidder A Bidder B Bidder C
Item 1 100 1,000 1,000 1,250 750
Item 2 100 20,000 22,000 16,000 19,000
Item 3 500 5,000 4,000 6,100 5,100
Item 4 60 6,000 6,000 4,800 5,600
Item 5 1,000 3,000 2,900 3,300 2,800
Item 6 400 1,600 1,000 1,600 2,100
Item 7 3,000 3,000 2,500 2,400 3,200
Item 8 20 25,000 31,000 20,000 26,000
1. Which of the following most nearly gives the total AAE in thousand pesos:
A. 64,600
B. 54,800
C. 48,000
D. 71,000
2. Which of the following give the complete list of major item?
A. Item 8
B. Items 2,4 & 8
C. Items 2,3,4, & 8
D. Items 2 & 8
3. Which of the following gives the complete list of unbalanced bids?
A. Bidders A, B, C
B. Bidders A, C
C. Bidders A
D. All are balanced bids
Solution:
Ave. of AGE 130% of
Item Qty AAE Bidder A Bidder B Bidder C
responsive bids AGE
1 100 1,000 1,000 1,250 750 875 937.50
2 100 20,000 22,000 16,000 19,000 19000 19500 25,350
3 500 5,000 4,000 6,100 5,100 4550 4775
4 60 6,000 6,000 4,800 5,600 5467 5733.3
5 1,000 3,000 2,900 3,300 2,800 3000 3000
6 400 1,600 1,000 1,600 2,100 1300 1450
7 3,000 3,000 2,500 2,400 3,200 2700 2850
8 20 25,000 31,000 20,000 26,000 23000 24000 31200
Note: bids inside shaded boxes are not responsive bids.
Unbalanced bids are those with bids higher than 130% of the AGE in respect to major items, while other items are
priced lower than the unit AGE.
Since no bid goes higher than 130% of AGE for items 2 & 8 (which are the major items), all bids are balance
Solution:
A. 7.63 cm
B. 12.45 cm
C. 9.54 cm
D. 8.45 cm
Solution:
The maximum radius of the inscribed circle for this condition is given by the formula:
At = rs
s = semi-perimeter = 102/2 = 51 cm
At = area of triangle = 34.772
431.1554 = r(51)
r = 8.454 cm
Two interior angles of a triangle measure 48° and 62°. If the perimeter of this triangle is 84cm, find the longest side
of the triangle.
A. 28.91cm
B. 34.56cm
C. 30.76cm
D. 24.33cm
Solution:
Mathematics “CE Board Exam Nov. 2008″
Salt is poured into a conical tank 100cm in diameter on top and 70cm high. If the volume of salt is 30,000 cm 3, what
is the depth of salt in the tank?
A. 45.21cm
B. 38.29cm
C. 31.25cm
D. 52.45cm
Solution:
Mathematics “CE Board Exam Nov. 2008″
The lower and upper bases of a frustum of a pyramid measure 18cm x 18cm and 10cm x 10cm, respectively. If its
lateral surface area is 448cm2, find the altitude of the pyramid.
A. 9.36cm
B. 8cm
C. 6.72cm
D. 6.93cm
Solution:
Mathematics “CE Board Exam Nov. 2008″
What is the surface area of a sphere having a volume of 1904 cubic meters?
A. 856.3 m2
B. 742 m2
C. 624.7 m2
D. 1056.2 m2
Solution:
Solution:
Design and Construction “CE Board Exam May 2008″
It is required to analyze the indeterminate truss shown. By superposition. The product AE = 10,000 where A is the
cross-sectional area in m2 and E is the modulus of elasticity in Pascals.
1. Which of the following most nearly gives the relative displacement of joints B and D if member BD is removed, in
meters?
A.0.012
B.0.004
C.0.005
D.0.008
2. Which of the following most nearly gives the relative displacement of joints B and D due to two unit loads (1 N)
acting at joints B and D acting towards each other, if member BD is removed.
A.0.001m
B.0.003m
C.0.004m
D.0.002m
3. Which of the following most nearly gives the value of the force on member BD in Newtons?
A.6.4
B.7.3
C.9.5
D. 7.9
Solution:
Design and Construction “CE Board Exam May 2008″
It is required to construct the influence line for the beam shown.
1. Which of the following most nearly gives the ordinate of the influence line for the vertical reaction at A at a point
4m from A:
A. 0.33
B. 0.67
C. -0.33
D. -0.67
2. Which of the following most nearly gives the ordinate of the influence line for the shear at D at a point 4m from
A:
A. 0.67
B. -0.33
C. -0.67
D. 0.33
3. Which of the following most nearly gives the ordinate of the influence line for the moment at D at a point 4m
from A:
A. -0.67
B. 0.67
C. 0.33
D. -0.33
Solution: