Professional Documents
Culture Documents
FOR TRIPPING
APPLICATIONS
This document may be subject to changes. Contact
ARTECHE to confirm the characteristics and availability
of the products described here.
Moving together
INDEX
4. ›› Technical standards
5. ›› General characteristics
.
6. ›› Range of products
7. ›› Trip relays
TECHNICAL STANDARDS
GENERAL STANDARDS
E322124
All the relays include a diode in parallel with the coil (see auxiliary
relays with overvoltage protection characteristic) and comply with
the shock and vibration standards, related to the relays with seismic
characteristics.
The correct state of the circuit is showed with a green LED on the front
plate of the relay. The output contacts change their position if the relay
detects a failure in the continuity of the circuit.
Connecting the relay across the trip circuit supply, the equipment
is normally energized. Faults will occur when the trip voltage is lost,
so the relay drops off in those cases, providing the related signs and
alarms. In order to avoid faulty alarms due to instantaneous supply
voltage dips, the drop off time of the relay is delayed over 100 ms so
those non-permanent failures of trip supply would not be considered.
›› World-class range of
auxiliary relays for
energy sector, specially
designed for the most
demanding applications
Applications Intended for tripping applications where high demanding requirements in operating time
(with tripping time from 8ms to 3 ms) and breaking capacity are needed,
that is the case of tripping HV and MV circuit breakers.
High burden configuration not available See page 15 for technical details
Construction characteristics
Contacts no. 2 Changeover 4 Changeover
11
3 7
(+) 2 7 (+) 2
12
3 5 4 8
8 13
4 6 5
Connections 9
(-) 1 (-) 1 14
6 10
Options
With 0P options • LED included • Diode in parallel with the coil included
Weight (g) 125 250
Dimensions (mm) (A) 22,5 x (B) 50,4 x (C) 72 (D type) (A) 42,5 x (B) 50,4 x (C) 72 (F short type)
Coil characteristics
Standard voltages(1) 24, 48, 110, 125, 220, 24, 48, 110, 125, 220,
250 (4) Vdc /110, 127, 48, 110, 125, 220, 250(4) 250 (4) Vdc / 110, 127, 48, 110, 125, 220, 250
230 Vac (50-60Hz) Vdc 230 Vac (50-60 Hz) (4)
Vdc
(1)
Other voltage upon request (3)
Ask for higher altitudes
(2)
Guarantee data for relays just manufactured (4
UL in progress for this voltage
Intended for tripping applications where high quality requirements in operating time (with models
Applications even tripping in less than 3 ms) and breaking capacity are needed, that is the case of tripping HV and
MV circuit breakers.
High burden configuration See page 15 for technical See page 15 for technical
not available
details details
Características constructivas
4 Changeover +
Contacts no. 8 Changeover 4 Fast Singles-Inversors without break
power
10
10
1 1 11
11
20 20
2 2 21
21
Trip
30 30
3 3 31
31
(+) d (+) d
Connections 40 40
4 4 41
41
50
50
5 51 5
Options With 0P options • LED included • Diode in parallel with the coil included
Weight (g) 500 335
Dimensions (mm) (A) 82,5 x (B) 50,4 x (C) 72 (J short type) (A) 82,5 x (B) 50,4 x (C) 72 (J short Type)
Coil characteristics
Standard voltages(1) 24, 48, 110, 125, 220, 250 (4) 48, 110, 125, 220, 110, 125, 220, 250 Vdc
Vdc/110, 127, 230 250(4) Vdc
Vac (50-60 Hz)
Voltage range +10% -20% UN +15% -20% UN
Pick-up voltage / Release voltage See pick-up/release voltage-temperature curves
Average consumption In permanence (UN) 1,4 W 6,5 W
Operating time
Pick-up time <8 ms Vdc (<10 ms Vac) <6,5 ms Contacts 1-4: <3 ms
(Range 24 Vdc <10 ms) Contacts 5-8: <20 ms
Drop-out time Vdc: <40 ms Vdc: <40 ms Contacts 1-4: <25 ms
Vac: <50 ms Contacts 5-8: <50 ms
Contacts
Contact material AgNi
Contacts resistance(2) ≤30 mΩ
Distance between contacts 1,2 mm Contacts 5-8: 1,2 mm
Permanent current 10 A Contacts 1-4: 8 A
Contacts 5-8: 15 A
Instantaneous current 30 A during 1 s / 80 A during 200 ms / 200 A during 10 Contacts 5-8: 30 A during 1 s / 80 A
ms during 200 ms / 200 A during 10 ms
Max. making capacity 40 A / 0,5 s / 110 Vdc Contacts 5-8: 40 A / 0,5 s / 110 Vdc
Breaking capacity See breaking capacity curves (Contact configuration Contacts 5-8: See breaking capacity
type B) curves (Contact configuration type B)
Max. breaking capacity See value for 50,000 operations Contacts 5-8: See value for 50,000
operations
Umax opened contact 250 Vdc / 400 Vac
Perfomance data
Mechanical endurance 107 operations
(1)
Other voltage upon request (3)
Ask for higher altitudes *Not recognized by UL
(2)
Guarantee data for relays just manufactured (4)
UL in progress for this voltage
High burden configuration See page 15 for technical details not available
Construction characteristics
Contacts no. 16 Changeover 4 Changeover
Terminals A Terminals B
10 10
1 11 1 11 NC1
20 20 C1
2 2 NO1
21 21
30 30
Connections 3 3
(+) 2 NC2
31 31
(+) d C2
40 40 NO2
4 41 4 41
NC3
50 50
5 51 5 51 C3
(-) a
NO3
60 60
6 61 6 61 (-) 1 NC4
70 70 C4
7 71 7 71
NO4
80 80
8 81 8 81
Options No options available
Weight (g) 1250 126
Dimensions (mm) (A) 120 x (B) 110 x (C) 105 (A) 53 x (B) 90 x (C) 58
Coil characteristics
Standard voltages(1) 110, 125, 220 Vdc 110, 125, 250 Vdc
Voltage range +10% -20% UN +10% -20% UN
Pick-up voltage (23 ºC) See pick-up/release voltage-temperature 61%
Release voltage (23 ºC)
curves 26%
Average consumption 12 W 2,8 W
Operating time
Pick-up time < 10ms <3 ms
Drop-out time <50 ms <4 ms
Contacts
Contact material AgNi AgNi
Permanent current 10 A 8A
Max. making capacity 40A / 0,5 s / 110 Vdc 15 A during 4s
Breaking capacity See breaking capacity curves (Contact See breaking capacity curves
configuration type A)
Umax opened contact 250 Vdc / 400 Vac 250 Vdc / 400 Vac
Performance data
Mechanical endurance 107 operations 107 operations
Operating temperature -25ºC +70ºC -40ºC +55ºC
Storage temperature -40ºC +85ºC -40ºC +85ºC
Max. operating humidity 93% / +40ºC 93% / +40ºC
Operating altitude (2)
<2,000 m <2,000 m
(1)
Other voltage upon request
(2)
Ask for higher altitudes
*
UL in progress
Applications Intended for trip and lockout applications where high demanding requirements in operating
time and breaking capacity are needed.
High burden configuration See page 15 for technical See page 15 for technical See page 15 for technical
not available
details details details
Construction characteristics
2 + 2 2
3 21 21
-
7 d 30
11 1 +
Set
Set d
3 30 30
-
Connections 3 - 12 31 +
Set
7 3 3
-
- 31 31
4 8 40
1 12 40 40
- c 4
4 8 13 41 4 41
c 4 41
+ 2 - -
Reset
5 9 50
14 13 50 50
=
b
Reset
5 5 5 b 5
Reset
51
Reset
14 51 51
=
9 + + +
=
=
6 10 60 60 60
- B1
6 6 61 6 61
10 61 a
a 70 - 70
- 70 7 7
71 71
7 71
80 80
80 8 81 8 81
8 81
Options Options are not available
Weight (g) 300 600 1250
Dimensions (mm) (A) 45 x (B) 45 x (C) 96,5 (F large Type) (A) 90 x (B) 50 x (C) 100,5 (A) 120 x (B) 110 x (C) 105
(J large Type)
Coil characteristics
Standard voltages(1) 24, 48, 72, 110, 125, 220 Vdc / 63,5, 110, 127, 230 Vac (50-60 Hz)
Voltage range +10% -20% UN
Pick-up voltage See pick-up voltage / temperature curves for Latching relays
Average consumptions only in 17 W 17 W 45 W 90 W
the change-over
Operating time
Pick-up time <10 ms (Vdc) <20 ms (Vac)
Contacts
Contact material AgNi
Distance between contacts 1,8 mm
Permanent current 10 A
Instantaneous current 80 A during 200 ms / 200 A during 10 ms
Max. making capacity 40 A / 0,5 s / 110 Vdc
Breaking capacity See breaking capacity curves (Contact configuration type A)
Max. breaking capacity See value for 50.000 operations
Umax opened contact 250 Vdc / 400 Vac
Performance data
Mechanical endurance 107 operations
Operating temperature -40ºC +70ºC
Storage temperature -40ºC +85ºC
Max. operating humidity 93% / +40ºC
Operating altitude(2) <2000 m
(1)
Other voltage upon request
(2)
Ask for higher altitudes
*
UL in progress
Applications Intended for tripping and locking applications where high quality requirements in operating time and breaking capacity are
needed, with manual reset.
10 A Terminals B Terminals
1 11 10 10
1 11 1 11
20
2 20 20
11 21
2 21 2 21
+ 3 d 30
Connections 7 30 d 30
+
Set
1 3
Set
-
31 +
Set
12 3 3
-
-
31 31
4 8 40
40 40
- c 4
13 41 4 41
c 4 41
2 - -
5 9 50 50 50
b 5 5 b 5
Reset
Reset
51
Reset
14 + 51 51
=
+
=
=
6 10 60 60 60
B1 6 6
6 61 61 61
a a
- 70 70 - 70
7 7
7 71
71 71
80 80
80
8 81 8 81
8 81
Options Options are not available
Weight (g) 300 600 1400
Dimensions (mm) (A) 45 x (B) 45 x (C) 96,5 (A) 90 x (B) 50 x (C) 100,5 (A) 120 x (B) 110 x (C) 105
(F large Type) (J large Type)
Coil characteristics
Standard voltages(1) 24, 48, 72, 110, 125, 220 Vdc 110, 125, 220 Vcc
63,5, 110, 127, 230 Vac (50-60 Hz)
Voltage range +10% -20% UN
Pick-up voltage (20ºC) See pick-up voltage / temperature curves for Latching relays
(1)
Other voltage upon request
(2)
Ask for higher altitudes
*
UL in progress
Applications Trip circuit supervision for single-phase circuit Trip circuit supervision for three-phase circuit
breakers breakers
Construction characteristics
Timing Contacts no. 2 Changeover 2 Changeover
FU
TRIP SUPPLY
+
FU
TRIP SUPPLY
Connections Trip contact
1 2 3
Trip contact Trip contact Trip contact
6 5
1 4 1 2 a 3 b 4 e 7
K23
K22
K13
K21
K12
K2
K11
K1 h
40
30
41
70
31
71
10
21
20
11
2 12 8
10 14 9 13
52b
52b
52b
52a
52a
52a
CB1 CB2 CB3
52a 52b
CIRCUIT BREAKER
CB
CIRCUIT BREAKER FU
TRIP SUPPLY
-
FU
TRIP SUPPLY
-
Standard voltages(1) 24/30, 60, 110/125, 220 Vdc, 110/127, 230 Vac (50-60 Hz)
Voltage range +10% -25% UN
Pick-up voltage (23º C) 70% UN
Operating time
Drop-out time >200 ms
Contacts
Contact material AgNi
Permanent current 8A
Instantaneous current 15 A
Max. making capacity 15 A during 4 s
Max. breaking capacity 0,3 A / 110 Vdc
Umax opened contact 250 Vdc / 400 Vac
Performance data
Mechanical endurance 107 operations
Operating temperature -40ºC +55ºC
Storage temperature -40ºC +85ºC
Max. operating humidity 93% / +40ºC
Operating altitude(2) <2000 m
(1)
Other voltage upon request
(2)
Ask for higher altitudes
Applications Supervise only the auxiliary supply circuit of the protection equipments,
avoiding false alarms due to short-time drop of supply
Construction characteristics
Timing Contacts no. 4 Changeover
11
3 7
(-) 1 12
4 8
Connections 13
5 9
(+) 2 14
6 10
Options Options are not available
Weight (g) 250
Dimensions (mm) (A) 42,5 x (B) 50,4 x (C) 96,6 (F large Type)
Coil characteristics
Standard voltages (1) 24, 48, 72, 110, 125, 220 Vdc / 63,5 , 110 , 127 , 230 Vac
Voltage range +10% -20% UN
Pick-up voltage See pick-up release voltage-temperature
curves for standard relays
Release voltage
Consumptions in permanence 4,5 W
Operating time
Pick-up time <20 ms
Drop-out time
To minimum voltage >100 ms
Maximum <400 ms
Contacts
Contact material AgNi
Contacts resistance (2) ≤30 mΩ
Distance between contacts 1,8 mm
Permanent current 10 A
Instantaneous current 80 A during 200 ms / 200 A during 10 ms
Max. making capacity 40 A / 0,5 s / 110 Vdc
Breaking capacity See breaking capacity curves
(Contact Configuration Type A)
Max. breaking capacity See value for 50.000 operations
Umax opened contact 250 Vdc / 400 Vac
Performance data
Mechanical endurance 107 operations
Operating temperature -40ºC +55ºC
Storage temperature -40ºC +85ºC
Max. operating humidity 93% / +40ºC
Operating altitude(3) <2000 m
(1)
Other voltage upon request
(2)
Guarantee data for relays just manufactured
(3)
Ask for higher altitudes
The standard high speed tripping relays For relays with rated voltage up to and
are manufactured with a low burden including the 125 V, the relays will withstand,
configuration, considering that the initiating without operating, a discharge into their
contact is placed close to the tripping relay. operate circuits of a 10µF capacitor charged
to 120% of the nominal voltage.
However, and in order to avoid unwanted trip
relay operation due to pickup or transients, For relays with rated voltage of 220 V, the
particularly if the relay operating coil is relays will withstand, without operating a
connected to extensive wiring, ARTECHE discharge into their operate circuits of a 10µF
tripping relays could be manufactured with capacitor charged to 100% of the nominal
a high burden configuration, complying with voltage.
ESI 48-4 international standard, as EB2 class
relays. These EB2 class relays are suitable Specifications:
for use in high security circuit breaker
tripping circuits, increasing their immunity to ESI 48-4 EB1: 1983 Low Burden
capacitance discharge currents. ESI 48-4 EB2: 1983 High Burden
Instantaneous relays (self reset relays): same consumption as low burden configuration
106 AgN90/10
In any configuration, ARTECHE’s auxiliary 2 x 8A
relays have a high breaking capacity values.
Cycles
These limits are showed in the table below,
in terms of power and current values. In
all the cases, these relays guarantee a right 105 DC-coll
performance during 50,000 operations. AC-coll
ELECTRICAL ENDURANCE
OTHER MODELS
24 Vdc voltage
Different loads configurations.
106
1000000 1000000
106
No. operations
No. operations
100000
105 100000
105
104
10000 10000
104
0
0,00 5,00
5 10,00
10 15,00
15 20,00
20 25,00
25 0,00
0 2,00
2 4,00
4 6,00
6 8,00
8 10,00
10 12,00
12
Current Current
Type A (Distance between contacts = 1,8 mm)
Type B (Distance between contacts = 1,2 mm)
0 ms 20 ms 40 ms
Type A
500 20,83 370 15,42 250 10,42
24
Type B 450 18,75 300 12,50 210 8,75
10000000
107 10000000
107
No. operations
No. operations
1000000
106 1000000
106
100000
105 100000
105
10000
104 104
10000
0
0,00 1
1,00 2
2,00 3
3,00 4
4,00 5
5,00 6
6,00 7
7,00 8
8,00 9
9,00 10
10,00 0
0,00 1
1,00 2
2,00 3
3,00 4
4,00 5
5,00 6
6,00 7
7,00
Current Current
0 ms 20 ms 40 ms
Type A
170 1,55 140 1,27 90 0,82
No. operations
1000000
106 106
100000
105 105
104
10000 104
0 1 2 3 4 5 6 7 8 9 10 0 0,5 1 1,5 2 2,5 3 3,5 4
0,00 1,00 2,00 3,00 4,00 5,00 6,00 7,00 8,00 9,00 10,00
Current Current
Type A
158 1,26 120 0,96 75 0,60
1000000
106 106
1000000
No. operations
No. operations
100000
105 100000
105
10000
104 104
10000
0,00
0,00 0,20
0,20 0,40
0,40 0,60
0,60 0,80
0,80 1,00
1,00 1,20
1,20 1,40
1,40 1,60
1,60 0,00
0,00 0,10
0,10 0,20
0,20 0,30
0,30 0,40
0,40 0,50
0,50 0,60
0,60 0,70
0,70 0,80
0,80
Current Current
0 ms 20 ms 40 ms
Type A
150 0,68 115 0,52 66 0,30
TRIPPING RELAYS
200
50
0
-40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100
Temperature (ºC)
200
100
Operative range of the coil voltage
50
0
-40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 130
Temperature (ºC)
Model Selection OP
Relay type
Standard model
4 contacts relay RF-4XR 0* 1 0 0 0
Range
High Burden HB
Low burden -
Aux. Supply
Vdc or Vac
Indicate voltage level and if it is
VDC or VAC
(ex: 24 VDC)
Options
No 0
Front LED
Yes 1
No 0
Mechanical contact position
indicator
Yes 1
No 0
Trip flag
Yes 1
No 0
*Mandatory option
Model Selection
Relay type
3 contacts relay BF-3R -
Range
High Burden HB
Low burden -
Aux. Supply
Vdc or Vac
Indicate voltage level and if it is
VDC or VAC
(ex: 24 VDC)
Aux. Supply
Aux. Supply
Vdc or Vac
Vdc or Vac
Indicate voltage level and if it is
Indicate voltage level and if it is
VDC or VAC
VDC or VAC
(ex: 24 VDC)
(ex: 24 VDC)
DIMENSIONS OF THE
RELAYS
›› Dimensions: A x B x C Type RXR
A
B
C
10,5
Size and weight vary depending on the model. Please refer to datasheet for detailed info.
IP10 Front connection JN-DE IP10 JN-DE2C IP10 225 Function signs on the extraction
IP20 Front connection JN-DE IP20 JN-DE2C IP20 225 ring
IP20 Rear connection JN-TR OP JN-TR2C OP 180
J Security pins
J-EMP
IP20 Flush mounting (short) 400
SHORT OP
IP20 Flush mounting J-EMP OP 400
Front connection I-DE 1000
I Rear connection I-TR I-TR2C 500
Flush mounting I-EMP 500
I-DE IP10
155
154
105
105
105
Socket
rear
connection
for DIN rail
or fix
Drilling
(1)
31 31 31
145
26
3,5
1 de
Sockets for
rear 108
connection
+
- +
84
= = -
Vaciado
= 52,6 =
Vaciado
Vaciado
Vaciado
104
=
90
112 min.
=
5
fø 122 min.
8o
(1)
DIN rail according to EN50022 DIN46277/3
(2)
Minimum distance between sockets will depend on type of relay and sockets. Please request sockets user manual for more detailed information.
15
15
Flush
mounting
sockets
for rear F-EMP OP J-EMP OP
connection
110
Sockets for
rear 108 108
connection
+
-
+
+ -
84
+
84
= = = = - -
Vaciado
Vaciado
= 52,6 =
= 52,6 =
Vaciado Vaciado
Vaciado
Vaciado
Vaciado Vaciado
104
104
=
90
90
112 min.
112 min.
=
=
Relays Type D Relays Type F Relays Type J 5 Relays Type I 5
fø 122 min. fø 122 min.
8o 8o
155
154
105
105
105
15 15
15 15
31 Flush 31 31
mounting
sockets
for rear F-EMP OP J-EMP OP
F-EMP J-EMP OP
connection
3,5
1 de 15 15
15 15
61 61
110
Cut-out Cut-out
50 50
66
66
Cut-out Cut-out
108
66
66
+
- + 66 84 66
= = Cut-Out -
Vaciado
= 52,6 =
Vaciado
Vaciado
Vaciado
104
=
90
112 min.
106
106
Cut-out
Cut-out
=
5
fø 122 min.
8o
15
15
F-EMP OP J-EMP OP
www.arteche.com ©Arteche