Professional Documents
Culture Documents
Multiprocesos Miller Serie XMT 425 CC-CV
Multiprocesos Miller Serie XMT 425 CC-CV
Multiprocess Welding
Power Source
Wind Tunnel Technology ™ protects 350 A of welding output at 60% duty cycle
electrical components and PC boards with superior low-end performance.
from contamination.
Power factor of .95 enables smaller
Fan-On-Demand™ cooling system fuses/breakers and primary wiring.
operates only when needed, reducing Primary amperage draw at rated output is
noise, energy use and the amount of 25% less than the competition.
contaminants pulled through machine. Ultra-tough, polycarbonate-blended
Lift-Arc allows TIG starting without
™ cover for control panel protects front
the use of high-frequency. Starts the controls from damage.
arc without contaminating the weld Low OCV Stick — A built-in, selectable
with tungsten. feature, that reduces the Stick mode
Adaptive Hot Start™ increases the open-circuit voltage (OCV) to nearly
output amperage at the start of a weld if 15 volts when the welding power source is
necessary, eliminating electrode sticking. not in use. Eliminates the need for add-on
XMT 425 VS voltage reducers.
Lightweight, aerospace-grade aluminum XMT 425 CC/CV
Dinse International-style weld disconnects
case offers protection with the benefit of
provide high-quality weld cable connections.
reduced weight. The XMT 425 Series is packed with
Auto-Line Power Management Technology
™
features to meet the most demanding Additional Features for XMT 425 CC/CV
welding needs.
allows for any input voltage hook-up
Auto Remote Sense™ enables unit to
(208 – 460 V) with no manual linking required,
Line voltage compensation keeps welding automatically use remote control if connected
providing convenience in any job setting. Ideal
output constant even if input power varies by to remote control receptacle.
solution for dirty or unreliable input power.
+/-10%. XMT 425 models further expand line
115 VAC auxiliary power provides 10 amps
Inverter arc control technology provides voltage compensation on 460 VAC to an
of circuit-breaker-protected power for water
greater puddle control for superior 6010 Stick amazing +37%, -59%.
circulators. Available on CE model.
electrode performance, and outstanding MIG
Large, dual digital meters are easy to view Pulsed MIG (GMAW-P) capabilities with
weld performance.
and are presettable to ease setting weld output. optional Optima™ control reduces spatter and
Process selector switch reduces the number of distortion, allows better out-of-position puddle
Exceptional electrical efficiency. At 400 A,
control setup combinations without reducing control, and provides potential reduction of
efficiency is 87.24%!
any features. fume particle emission.
Certified to both the Canadian and U.S. Standards for welding equipment.
300 70 70
VOLTAGE
1-PHASE OPERATION
VOLTAGE
60 60
250
6 AWG POWER CORD 50 GTAW
50
SMAW
200 MAX MAX MAX
40 40
8 AWG POWER CORD
30 SMAW 30
GTAW 80A
150 MIN ARC
20 0% CONTROL 20
25%
50% MIN
10 10
75%
100% 0
100 0
10 15 20 25 30 40 50 60 70 80 90 100 0 100 200 300 400 500 0 100 200 300 400 500
DUTY CYCLE AMPS AMPS
Control Panels
XMT 425 VS XMT 425 CC/CV
Manufactured Under the Manufactured Under the
Following US Patents: Following US Patents:
5,601,741 5,642,260 5,902,150
6,002,103 6,115,273 6,193,548
6,239,407 6,266,257 6,625,046
6,611,189 6,426,888
3 5,601,741 5,642,260 5,902,150
6,002,103 6,115,273 6,193,548
6,239,407 6,266,257 6,625,046
6,611,189 6,426,888
4
Other Patents Pending Other Patents Pending
1 4 1 5
CC
2 5 2 6
1. Voltmeter 1. Voltmeter
2. Process Selector Switch (Rotary Switch) 2. Remote Control Receptacle
3. Ammeter 3. Process Selector Switch (Rotary Switch)
4. Voltage/Amperage Adjustment Control 4. Ammeter
5. Arc Control 5. Voltage/Amperage Adjustment Control
6. Arc Control
2
Genuine Miller Accessories
HF-251D-1 Running Gear Water Coolant Systems
High-Frequency Arc
Starter and Stabilizer XMT Cylinder Cart For more information, see the Miller Coolant
#042 388 #042 537 Systems literature sheet, Index No. AY/7.2.
Portable 250 amp, 60% Carries two 160 lb (72.6 kg) Coolmate™ 3
duty cycle unit adds high gas cylinders, or one gas #043 007 115 VAC
frequency to the welding cylinder and one coolant #043 008 230 VAC
circuit to help start the arc system for TIG (GTAW) For use with water-cooled torches rated up to
when using the DC TIG (GTAW) process. Operates welding. Feeder mounts to 600 amps. Unique paddle-wheel indicator,
on 115 VAC, 50/50 Hz. See Lit. Index No. AY/5.1. tray above power source. external filter and easy-fill spout.
RFCS-14 Foot Control Coolmate™ V3 #043 009 115 VAC
#043 554
Wire Feeders/Guns For use with water-cooled torches rated up to
Heavy-duty foot current SuitCase™ 8VS #194 890 500 amps. Vertical design conveniently mounts
and contactor control. SuitCase™ X-TREME™ 12VS #195 500 to Miller cylinder rack in place of one cylinder.
Includes 20 ft (6 m) cord Lightweight, portable wire feeder for a variety of Coolmate™ 4 #042 288 115 VAC
and 14-pin plug. wires up to .062 in. Holds up to an 8 in (8VS) or For use with water-cooled torches rated up to
RHC-14 Hand Control 12in (12VS) spool of wire. Operates on open- 600 amps. Tough molded polyethylene case
#129 340 circuit voltage eliminating the need for a control/ with carrying handle.
Miniature hand control power cord. See Lit. Index No. M/6.4 and M/6.41. Coolant #043 810 Sold in cases of four
for remote current and SuitCase™ 8RC/12RC #194 938/#194 940 1-gallon recyclable plastic bottles. Miller
contactor control. Lightweight, portable wire feeder for a variety of coolants contain a base of ethylene glycol and
Dimensions: 4 x 4 x 3-1/4 in wires up to .062 in. Holds up to an 8 in (8RC) or deionized water to protect against freezing to
(102 x 102 x 82 mm). Includes 20 ft (6 m) cord 12 in (12RC) spool of wire. Operates using 14- -37˚F (-38˚C) or boiling to 227˚F (108˚C). Also
and 14-pin plug. pin control receptacle. See Lit. Index No. M/6.5. contains a compound that resists algae growth.
RMLS-14 #129 337 XR™-Control #181 538
14-pin plug. Momentary- Push-pull wire feed system offers unparalleled
International-Style Connectors
and maintained-contact performance for aluminum MIG welding. See Note: XMT 425 power sources are equipped with
rocker switch for contactor control. Push Lit. Index No. M/1.7. International-style connectors for secondary
forward for maintained contact and back for connections. (Power source is shipped with two
70 Series 50-mm male International-style plugs for use with
momentary contact. Includes 20 ft (6 m) cord.
S-74S #195 057 #1 or #2 AWG size cable.)
RCC-14 Remote S-74D #195 058
Contactor and Current International/Tweco® Adapter
S-74DX #195 059
Control #151 086 #042 465
Wire feeder features Posifeed™ wire drive
14-pin plug. Rotary-motion fingertip control International/Cam-Lok Adapter
assembly and handles a variety of wires up to
fastens to TIG torch using two Velcro® straps. #042 466
1/8 in. Comes with FREE Bernard® Q™-Gun. See
Includes 28 ft (8.5 m) control cord. One-piece adapter with International-style male
Lit. Index No. M/3.0.
plug (to power source) on one end and female
RCCS-14 Remote Spoolmatic® 30A receptacle (Tweco or Cam-Lok for weld cable
Contactor and Current #130 831 connection) on other end.
Control #043 688 A 1-lb, air-cooled
International-Style Connector Kit
Up-and-down rotary-motion fingertip control. spool gun that
Great for applications that require a finer extends the weld #042 418 50 mm
amperage control. Includes 28 ft (8.5 m) control process range by Accepts #4 or #1/0 AWG cable size. Required if
cord. adding a handy male plugs shipped with power source must be
portable system for small wire MIG. Rated 200 replaced, or if additional plugs are needed.
Extension Cords for Remote Controls
A at 100% duty cycle. Includes 30 ft (9.1 m) #042 533 70 mm
and 24 VAC Wire Feeders
cable assembly. (WC-24 #137 549 for 14 pin.) Accepts #1/0 or #2/0 AWG cable size. Required
#122 973 25 ft (7.6 m)
if #1/0 or #2/0 AWG size cable is to be used.
#122 974 50 ft (15.2 m) Ironmate™ Flux Cored Guns
#122 975 75 ft (22.8 m) See Lit. Index No. AY/16.0. Kit includes one International-style male plug
14-pin plug to 14-pin socket. which attaches to the work and/or weld cables
FC-1260
Note: Not for use with Optima or 60M Series.
and plugs into the International-style receptacles
#195 732 10 ft (3 m)
on the power source.
#195 729 15 ft (4.6 m)
Protective Cover FC-1260LM Extension Kit for International-Style
#194 912 10 ft (3 m) Cable Connectors
Protective Cover
#195 478 #194 911 15 ft (4.6 m) #042 419 50 mm
Mildew and water FC-1150 Accepts #4 or #1/0 AWG size cable.
resistant, odor-free cover #194 864 10 ft (3 m) #042 534 70 mm
protects your machine’s #194 863 15 ft (4.6 m) Accepts #1/0 or #2/0 AWG size cable.
finish. For 300/350 A Used to adapt or extend weld and/or work cables.
inverters: XMT, Maxstar Kit includes one male International-style plug and
and Dynasty. one in-line female International-style receptacle.
3
Ordering Information
Power Source and Options Stock No. Description Qty. Price
XMT® 425 CC/CV #907 386 208 – 575 VAC with Auto-Line™
#907 386-01-1 230 – 460 VAC with Auto-Line™ and Auxiliary Power and CE
XMT® 425 VS #907 387 208 – 575 VAC with Auto-Line™
Accessories
Optima™ MIG Pulse Control #043 389 For CC/CV models only. Not for use with XMT 425 VS
Optima™ Extension Cords See page 4
Gas Solenoid Kit #195 286
Process Selector Control #042 872
WC-24 #137 549 For use with Spoolmatic® 30A and power sources with 14-pin
WC-115A #137 546-01-1 For use with Spoolmatic® 30A and power sources without 14-pin
HF-251D-1 HF Starter/Stabilizer #042 388 See Lit. Index No. AY/5.1
RFCS-14 #043 554 Foot control
RHC-14 #129 340 Hand control
RMLS-14 #129 337 Rocker switch
RCC-14 #151 086 Fingertip control
RCCS-14 #043 688 Fingertip control
Extension Cords (For 24 VAC wire See page 4. Not to be used with Optima, 60M or XR-M
feeders and remote controls)
Running Gear
XMT Cylinder Cart #042 537
Wire Feeders/Guns
SuitCase™ 8VS / X-TREME™ 12VS #194 890 / #195 500 See Lit. Index No. M/6.4 and M/6.41
SuitCase™ 8RC / 12RC #194 938 / #194 940 See Lit. Index No. M/6.5
™
XR -Control #181 538 See Lit. Index No. M/1.7
70 Series #195 057 S-74S. See Lit. Index No. M/3.0
#195 058 S-74D. See Lit. Index No. M/3.0
#195 059 S-74DX. See Lit. Index No. M/3.0
Spoolmatic® 30A Spool Gun #130 831 Includes 30 ft (9.1 m) cable assembly
Ironmate Flux Cored Guns
™ See Lit. Index No. AY/16.0
Water Coolant Systems See page 6. See Lit. Index No. AY/7.2
Distributed by:
Litho in USA