Professional Documents
Culture Documents
COM
tem
Alarm Sys
og Canno
n Dimensioning Zone Fog
NO
Version 1.5
COM. Zone Fluid
NC
per
NO
Zone Tam
COM.
NC
NO
nal
Disable Sig 12 V –
daytime
– Closed ind
Fire +
nal
– Alarm Sig 12 V –
h alarm
Disable + Opens wit
– 12 V +
Sec. +
–
Prim +
–
PIR
Arm + Motion
+
12 V – Tamper
Output
+
Tamper 12 V
–
DIMENSIONING - CHECKLIST HEATING TIME REHEATING TIME
POINT PROTECTION 1. 2.
3. 4.
FULL PROTECTION 1. 2. 1. 2.
3. 4. 3. 4.
35 cm
Min. 2,5 m.
Min. 2,5 m.
DIMENSIONING EXAMPLES
In general:
The fog output from the PROTECT Fog Cannons®, are defined by the so called ”Industrial standard”, meaning that the visibility in the relea-
sed fog, is app. 1,5m after 60 seconds. Meaning that a Protect 600i TM running for 60 seconds, will produce 700 m3 fog. Released in a room of
700 m3, this will give a visibility of 1,5 meter.
The standard EN 50131-8, requires the visibility, after 60 seconds, to be 1 meter.
We recommend, to achieve 1 meter visibility, to have the measured room’s volume multiplied by 2.
Example: a room of 12 x 9 x 3 meter, equal to 108 m2 and 324 m3. Twice the volume is 648 m3.
In this case the model 600iTM will be suitable, making 700 m3 in 60 sec.
The calculations are only indicative. You need to make a full-scale test to ensure that your dimensioning are correct, and to make sure that
the coverage is satisfying.
EXAMPLES
Office space. Ceiling height 3 meters A private living room, ceilingheight 2,5 meter.
120 m2 - 360 m3 Area 36 m2, volume 90 m3
8m 9m
Primary
area
4m
15 m
Second Secondary
Primary Primary ary area
area
area area
Warehouse. Ceiling height 4,5 meters Shop. Ceiling height 3,5 meters
240 m2 - 1080 m3 180 m2 - 630 m3
6 meter
Port
Primary
Secondary Primary area
Secondary
area area area
12 m
20 m
Port
20 meter
OTHERS
Standby consumption after heating up: 60 W (on average) P “Primary Trig” input activated.
Battery backup (2 x 12 V, 1.2 Ah): Backup of electronics and pump 90220403 3-hole nozzle
E3 Fire alarm input activated.
90020433 30 degree 3-hole nozzle
Power backup after power failure: Up to 3 hours
90020000 Nozlle extension 15 cm E4 Low battery voltage.
Built-in automatic battery testing: Yes
90020500 Ceiling plate
Failed attempts to charge the battery for
Signals/Indications: Optical, audible and electrical 90020500 Hoist tool E5 24 hours.
DIP Function
Heat disable. On = The heating element
FOG TIME DIP 2-3-4
1
disconnects if disable is activated
3 Fog time
Dip Setting Fog Time Fog Volume
4 Fog time
60 sec. fog Fog output Fog output Fog output Fog output Fog output
Break Break Break Break Break
White - Item no.: 90011118
DISPLAY EXPLANATION
SPECIFICATIONS: DISPLAY
H Heating. The system is in the heating
phase and has not reached operating
Performance (fog generation), examples: 60 sec.: 1300 m³ temperature.
60 sec.: 1300 m³
60 sec.: 1300 m³ r The system has reached normal operating
temperature and is ready to produce fog.
Standby consumption after heating up: 70 W (on average) P “Primary Trig” input activated.
Battery backup (2 x 12 V, 1.2 Ah): Backup of electronics and pump 90020403 3-hole nozzle
E3 Fire alarm input activated.
90020433 30° degree 3-hole nozzle
Power backup after power failure: Up to 3 hours
90020000 Nozlle extension 15 cm E4 Low battery voltage.
Built-in automatic battery testing: Yes
90020505 Ceiling plate
Failed attempts to charge the battery for
Signals/Indications: Optical, audible and electrical 90020500 Hoist tool E5 24 hours.
DIP Function
Heat disable. On = The heating element
FOG TIME DIP 2-3-4
1
disconnects if disable is activated
3 Fog time
5 Arm*
Dip 2 Dip 3 Dip 4 m³
6 Primary* OFF OFF OFF demo demo
60 sec. fog Fog output Fog output Fog output Fog output Fog output
Break Break Break Break Break
White - Item no.: 90012218
DISPLAY EXPLANATION
SPECIFICATIONS: DISPLAY
H Heating. The system is in the heating
phase and has not reached operating
Performance (fog generation), examples: 60 sec.: 2700 m³ temperature.
70 sec.: 2875 m³
60 sec. with 10-min. pulse: r The system has reached normal operating
temperature and is ready to produce fog.
3700 m³
d ”Disable” input activated and system
Fog generation settings: Can be timed at 4 intervals blocked, as the alarm is not connected
from 900-2875 m3 (heating has not been disconnected).
Standby consumption after heating up: 80 W (on average) P “Primary Trig” input activated.
Re-heating time after fog discharge: 0–14 min. Black - Item no.: 90012219 bAt A battery is (or has been) mounted.
Battery backup (2 x 12 V, 1.2 Ah): Backup of electronics and pump 90022203 3-hole nozzle
E3 Fire alarm input activated.
90022233 30° degree 3-hole nozzle
Power backup after power failure: Up to 3 hours
90020000 Nozlle extension 15 cm E4 Low battery voltage.
Built-in automatic battery testing: Yes
90020506 Ceiling plate
Failed attempts to charge the battery for
Signals/Indications: Optical, audible and electrical 90020500 Hoist tool E5 24 hours.
DIP Function
Heat disable. On = The heating element
FOGTIME DIP 2-3-4
1
disconnects if disable is activated
3 Fog time
Dip Setting Fog Time Fog Volume
4 Fog time
60 sec. fog Fog output Fog output Fog output Fog output Fog output
Pulse mode: Yes, can shoot several times (3 settings) d ”Disable” input activated and system
blocked, as the alarm is not connected
(heating has not been disconnected).
Fog fluid container: 1.1 litre (same as model 600TM /600iTM and 1100TM /1100iTM )
Hd ”Heat Disable”. ”Disable” input activated
Shots per container: Min. 20 and system blocked, as the alarm is not
connected. Heating is also disconnected, as
dipswitch 1 is in the ON position.
Electronic fluid measurement: Yes
bt “Blocking timer active”. System blocked
Mains connection: 230 V, 50 Hz z from fog triggering internally (timer-con-
trolled). This occurs after the fog has been
triggered or in connection with system
Power consumption: 700 W start-up after loss of mains voltage.
C
CONSUMER GOODS
The battery is currently being charged.
Input: 5 signals
Built-in automatic battery loading: Yes Failed attempts to charge the battery for
E5 24 hours.
Signals/Indicators: Audible, optical, and electrical
E6 Battery failed load test.
PCB status indicator: Yes
E7 PCB temperature too high.
Data log memory: Yes, optional with IntelliSuiteTM TYPICAL
Dimensions (mm): L: 400, B: 240, H: 135 SPARE PARTS E8 PCB temperature too low.
DIP Function
Heat disable. On = The heating element
FOG TIME DIP 2-3-4
1
disconnects if disable is activated
9 Reserved. Leave in OFF position OFF OFF ON - 10 sec. of fog + 3 pulse shots (in all about 90 sec. fog)
ON OFF ON - 10 sec. of fog + 6 pulse shots (in all about 180 sec. fog)
10 Error indicator. On = Beeper connected
6 sec. of fog (full speed) + 294 sec. of fog
OFF ON ON - (reduced speed). In all 300 sec. fog
* ON = normal open.
OFF = normal closed. ON ON ON -
5 sec. of fog (at normal speed)
+ 5 min. of continuous fog (at very slow speed)
** ON = delay is active.
DISPLAY / FAULT CODES
FOG OUTPUT DIAGRAM
PrO Ec 600 EU P. P: Primary trig norc. norc: No remote control signal*
S. S: Secondary trig rd. Remotely disabled* 180
Display/ b.A. . bat: battery rHd. rHd: Remotely heat disabled*
H. H: Heat
fault codes r. r: ready C. C: Charge rP. rP: Remote primary* 144
d. d: disable E. E: Error + no rb. rb: Remotely blocked*
H.d. Hd: Heat disable 1.234567890 rF. rF: Remote fire alarm*
B. . Bt: Blocking timer 1. 2 3 4 5 6 8 7 9 0 rPA rPA: Remote panic alarm activated*
A. A: Arm trig rc. rc: Remotely controlled*
72
6/10 sec. fog Fog output Fog output Fog output Fog output Fog output
0
0 sek. 10 sek. 20 sek. 30 sek.
Break Break Break Break Break
White - Item no.: 90010101
DISPLAY EXPLANATION
SPECIFICATIONS: DISPLAY
H Heating. The system is in the heating
phase and has not reached operating
Performance (fog generation): 60 sec.: 400 m3 temperature.
Fog generation settings: Can be timed at 3 intervals from 140 – 400 m3 r The system has reached normal operating
temperature and is ready to produce fog.
Operating temperature (min./max.): 5/80° C. bAt A battery is (or has been) mounted.
Input: 5 signals C
CONSUMER GOODS
The battery is currently being charged.
Output: 3 signals
E1 Mains voltage failure.
Control settings for fog time, signals and heating: On/off DIP switches 90020209 XTRA+ Fog fluid Bag 0,4 l
90020430 30 degree nozzle E2 Low fluid level.
Battery backup: Yes. Please notice: QUMULUSTM is delivered without batteries
SPP1060 Batteri 12V - 1,2Ah
Power backup after mains connection loss: Up to 1 hour (requires batteries, E3 Fire alarm input activated.
which are not delivered as standard).
E4 Low battery voltage.
Signals, indicators: Yes, optical, audible and electrical
Failed attempts to charge the battery for
Status indicator on PCB: Yes E5 24 hours.
DIP Function
Heat disable. On = The heating element
FOG TIME DIP 2-3-4
1
disconnects if disable is activated
60 sec. fog Fog output Fog output Fog output Fog output Fog output
Break Break Break Break Break
ELECTRICAL INSTALLATION
Dip 8
5 sec. delay
• Galvanic isolated
• Nominal 12V – 5 mA
• Inputs must be polarized correctly
• Inputs can be connected with 24V by connecting a
resistance in series with the signal (2.4 Kohm)
Zone Tamper
–
Fire + Disable Signal
– 12 V –
Disable +
Closed in daytime
Alarm Signal
– 12 V –
Sec. + Opens with alarm
12 V +
–
Prim +
–
Arm +
12 V +
Output –
VERIFYING PIR
Tamper
Motion
Tamper
+
–
12 V
Setup PROTECT IntelliSuite TM
• Install Driver to IntelliConnectorTM (cable)
• Install IntelliSuiteTM (Software) from PROTECTTM Download
Center
• Connect the IntelliConnectorTM (Cable) to the Fog CannonTM
• Choose communications port
• Setup is normally only necessary once per laptop
• The Cable has a build in 3kV galvanic seperation
to ensure the Fog CannonTM and the laptop
System Monitor
• Faults and reasons
• Condition on indputs and outputs
• Batteri condition
• Fluid level
• Operating time
• Dipswitch settingsguide
(fog time)
Report tool
• All information in one text file
• Saves the last known
dipswitch settings
• Shows faults
• Status on inputs
• Status on outputs
• Analog values
White - Item no.: 90010013
DISPLAY EXPLANATION
SPECIFICATIONS: GREEN LIGHT
Flashes when heating (1 flash/sec.).
Prepared for 0,4 l. fluid container (not included) Lights constantly when Xtratus® is Ready.
Turns off if error occurs.
Enough fluid for 2 discharges in one fluid container
Installation weight: 10 kg
250
Heat disable
225
& 115/130V
On = The heating element disconnects 250 m3 at 1 meter visibility.
1
if disarm is activated 200
OFF = Constantly heating
175
2 Trig 1* 150
3 Trig 2* 125
100
Reserved.
4
Leave in OFF position 75
Error indicator/buzzer 50
5
ON = Beeper/buzzer connected 25
* ON = Normal open. 0
0 Sec. 4 Sec. 8 Sec. 12 Sec. 16 Sec.
OFF = Normal closed.
Immediately after, the Xtratus® will tell you which error is present - simply
by counting the present error. This is done by use of the red light and the
buzzer that will flash and beep the error number.
Output 1
Normally Open
when alarm system
is ARMED (Night)
Alarm panel
PROTECTGLOBAL.COM
GB PROTECT A/S is the world’s largest supplier and the only producer of fog cannons in Scandinavia.
PROTECTTM is represented worldwide in 50 countries.
PROTECT A/S · Hasselager Centervej 5 · DK-8260 Viby J · Tel.: (+45) 86 72 18 81 · Fax: (+45) 86 72 18 82 · Mail: info@protectglobal.com