Professional Documents
Culture Documents
Edge
50116 Wipers and Washers 2015 Edge
Removal and Installation Procedure revision date: 01/30/2015
Rain Sensor
Removal
1. Remove the interior rear view mirror.
Refer to: Interior Rear View Mirror (50109 Rear View Mirrors, Removal and Installation).
2.
Remove the rain sensor.
1. Disconnect the electrical connector and position aside.
2. On both sides.
Release the retainers.
3. Remove the rain sensor.
om
.c
er
ov
ec
itr
.b
w
w
w
Installation
1. Clean the windshield glass area of foreign materials.
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 1/3
8/1/2016 2015 Edge
om
.c
er
2. NOTE: If the rain sensor gel pack is damaged, install a new rain sensor.
Inspect the rain sensor gel pack for damage.
ov
ec
itr
.b
w
w
w
3. Install the rain sensor and connect the electrical connector.
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 2/3
8/1/2016 2015 Edge
om
.c
4. Install the interior rear view mirror.
er
Refer to: Interior Rear View Mirror (50109 Rear View Mirrors, Removal and Installation).
ov
ec
itr
.b
w
w
w
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 3/3
8/1/2016 2015 Edge
50116 Wipers and Washers 2015 Edge
Removal and Installation Procedure revision date: 01/30/2015
Rear Window Wiper Motor
Base Part Number: 17508
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. Remove the rear window wiper pivot arm.
Refer to: Rear Window Wiper Pivot Arm (50116 Wipers and Washers, Removal and Installation).
2. Remove the liftgate trim panel.
Refer to: Liftgate Trim Panel (50105 Interior Trim and Ornamentation, Removal and Installation).
3. Disconnect the wiper motor electrical connector.
om
.c
er
ov
ec
itr
.b
w
w
w
4. Remove the bolts and the rear window wiper motor.
Torque: 71 lb.in (8 Nm)
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 1/2
8/1/2016 2015 Edge
om
.c
Installation
1. To install, reverse the removal procedure.
er
ov
ec
itr
.b
w
w
w
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 2/2
8/1/2016 2015 Edge
50116 Wipers and Washers 2015 Edge
Removal and Installation Procedure revision date: 01/30/2015
Rear Window Wiper Pivot Arm
Special Tool(s) / General Equipment
Two Leg Puller
Removal
1. Open the wiper pivot arm nut cover.
om
.c
er
ov
ec
itr
.b
w
w
2. Remove the wiper pivot arm nut.
w
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 1/4
8/1/2016 2015 Edge
om
.c
3. Remove the wiper pivot arm.
Use the General Equipment: Two Leg Puller er
ov
ec
itr
.b
w
w
w
Installation
1.
Verify the rear window wiper motor is in the PARK position.
1. Set the ignition switch to the ON position.
2. Push the rear wiper switch to cycle the rear wiper motor.
3. Set the ignition switch to the OFF position.
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 2/4
8/1/2016 2015 Edge
om
.c
2.
Install the wiper pivot arm. er
ov
1. Align the wiper blade on the wavy defroster grid line.
2. Install the wiper pivot arm nut.
Torque: 106 lb.in (12 Nm)
ec
itr
.b
w
w
w
3. Close the wiper pivot arm nut cover.
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 3/4
8/1/2016 2015 Edge
om
.c
er
ov
ec
itr
.b
w
w
w
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 4/4
8/1/2016 2015 Edge
50116 Wipers and Washers 2015 Edge
General Procedures Procedure revision date: 04/24/2012
Washer Hose Coupling
Disconnect
1. WARNING: Before beginning any service procedure in this section, refer to Safety Warnings in section
10000 General Information. Failure to follow this instruction may result in serious personal injury.
Refer to: Health and Safety Precautions (10000 General Information, Description and Operation).
2. NOTICE: To prevent damage to the coupler, do not use hand tools to disconnect /connect the Clock.
NOTE: Do not remove the lock ring from the Clock coupler.
NOTE: Hold the female side of the coupler at the hose connection to prevent the coupler from rotating internally.
om
Gently twist the lock ring until it has rotated approximately 90 degrees.
.c
er
ov
ec
itr
.b
w
w
3. NOTICE: The female side of the Clock coupler contains an oring seal. Use care not to lose the oring.
w
Slide the Clock coupler apart from the component fitting.
4. NOTICE: Do not leave the lock ring in the unlocked position. This will weaken the lock ring and prevent it
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 1/2
8/1/2016 2015 Edge
from correctly locking in place when reassembled, resulting in a leak.
Rotate the lock ring back to the original locked position.
5. To connect, verify the Clock coupler lock ring is in the locked position.
om
6. NOTE: The lock ring flexes open slightly to allow the male fitting to enter the Clock coupler.
NOTE: The lock ring can be heard as it snaps into the lock position.
.c
Insert the male fitting into the Clock coupler.
7. Gently pull on the Clock coupler to verify it is seated correctly.
er
ov
ec
itr
.b
w
w
w
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 2/2
8/1/2016 2015 Edge
50116 Wipers and Washers 2015 Edge
General Procedures Procedure revision date: 10/28/2015
Washer Hose Repair
Repair
NOTE: This procedure may be carried out on rubber hoses only. If a plastic washer hose is damaged, a new washer hose
must be installed.
1. Locate and verify the damaged washer hose.
2. Cut the hose cleanly and remove the damaged portion of the washer hose.
Dimension: 0.5000 in (12.7 mm)
om
.c
er
ov
ec
itr
.b
w
w
w
3. Install a windshield washer hose adapter between the cut ends of the hose.
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 1/3
8/1/2016 2015 Edge
om
.c
er
ov
ec
itr
.b
4. NOTE: In difficult cases, clamping may be required.
w
If necessary, install a segment of 6.4 mm (0.25 in) ID black rubber hose over the ends of the washer hose and
clamp both ends of the rubber hose using spring clamps.
w
w
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 2/3
8/1/2016 2015 Edge
om
.c
er
ov
ec
itr
.b
w
w
w
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 3/3
8/1/2016 2015 Edge
50116 Wipers and Washers 2015 Edge
Removal and Installation Procedure revision date: 01/30/2015
Windshield Washer Fluid Level Sensor
Special Tool(s) / General Equipment
Fluid Suction Gun
Fluid Container
Materials
Name Specification
Windshield Washer Fluid WSSM14P19A
CXC37A/B/D/F
om
Removal
NOTE: Hood removed in this procedure for clarity.
.c
1. Siphon the windshield washer fluid out.
Use the General Equipment: Fluid Suction Gun
Use the General Equipment: Fluid Container
er
ov
ec
itr
.b
w
w
w
2. Remove the RH fender splash shield.
Refer to: Fender Splash Shield (50102 Front End Body Panels, Removal and Installation).
3. Detach the wire harness retainer and disconnect the level sensor electrical connector.
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 1/3
8/1/2016 2015 Edge
om
.c
4. NOTE: Be prepared to collect escaping fluid.
Remove the fluid level sensor.
er
ov
Use the General Equipment: Fluid Container
ec
itr
.b
w
w
w
Installation
NOTICE: Do not operate the washer pump prior to filling the windshield washer reservoir. Failure to follow this
instruction may result in premature pump failure.
1. To install, reverse the removal procedure.
Material: Windshield Washer Fluid / CXC37A/B/D/F (WSSM14P19A)
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 2/3
8/1/2016 2015 Edge
om
.c
er
ov
ec
itr
.b
w
w
w
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 3/3
8/1/2016 2015 Edge
50116 Wipers and Washers 2015 Edge
Removal and Installation Procedure revision date: 01/30/2015
Windshield Washer Pump
Special Tool(s) / General Equipment
Fluid Suction Gun
Fluid Container
Materials
Name Specification
Windshield Washer Fluid WSSM14P19A
CXC37A/B/D/F
om
Removal
NOTE: Hood removed in this procedure for clarity.
.c
1. Siphon the windshield washer fluid out.
Use the General Equipment: Fluid Suction Gun
Use the General Equipment: Fluid Container
er
ov
ec
itr
.b
w
w
w
2. Remove the RH fender splash shield.
Refer to: Fender Splash Shield (50102 Front End Body Panels, Removal and Installation).
3. Detach the wire harness retainer and disconnect the washer pump electrical connector.
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 1/4
8/1/2016 2015 Edge
om
.c
4. NOTE: Be prepared to collect escaping fluid.
Detach the washer hoses.
er
ov
Use the General Equipment: Fluid Container
ec
itr
.b
w
w
w
5. NOTE: Be prepared to collect escaping fluid.
Remove the washer pump.
Use the General Equipment: Fluid Container
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 2/4
8/1/2016 2015 Edge
om
.c
Installation
er
NOTICE: Do not operate the washer pump prior to filling the windshield washer reservoir. Failure to follow this
ov
instruction may result in premature pump failure.
1. To install, reverse the removal procedure.
ec
Material: Windshield Washer Fluid / CXC37A/B/D/F (WSSM14P19A)
itr
.b
w
w
w
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 3/4
8/1/2016 2015 Edge
om
.c
er
ov
ec
itr
.b
w
w
w
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 4/4
8/1/2016 2015 Edge
50116 Wipers and Washers 2015 Edge
Removal and Installation Procedure revision date: 10/8/2015
Windshield Washer Reservoir
Special Tool(s) / General Equipment
Fluid Suction Gun
Fluid Container
Removal
1. NOTE: Hood shown removed for clarity.
Siphon the windshield washer fluid out.
Use the General Equipment: Fluid Suction Gun
Use the General Equipment: Fluid Container
om
.c
er
ov
ec
itr
.b
w
w
w
2. Remove the filler neck bolt.
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 1/6
8/1/2016 2015 Edge
om
.c
3. Remove the front bumper cover.
er
Refer to: Front Bumper Cover (50119 Bumpers, Removal and Installation).
ov
4. NOTE: Fender splash shield shown removed for clarity.
Detach the wire harness retainer and disconnect the level sensor electrical connector.
ec
itr
.b
w
w
w
5. NOTE: Fender splash shield shown removed for clarity.
NOTE: Be prepared to collect escaping fluid.
Disconnect the washer pump electrical connector and detach the washer hoses.
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 2/6
8/1/2016 2015 Edge
Use the General Equipment: Fluid Container
om
.c
er
ov
6. NOTE: Fender splash shield shown removed for clarity.
Remove the lower reservoir bolt.
ec
itr
.b
w
w
w
7. NOTE: Fender splash shield shown removed for clarity.
1. Detach the washer hose retainer and position aside.
2. Remove the pintype retainer.
3. Remove the upper reservoir bolt.
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 3/6
8/1/2016 2015 Edge
om
.c
8. NOTE: Fender splash shield shown removed for clarity.
er
ov
Remove the washer reservoir.
ec
itr
.b
w
w
w
9. NOTE: This step is only necessary when installing a new component.
Remove the fluid level sensor.
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 4/6
8/1/2016 2015 Edge
om
.c
10. NOTE: This step is only necessary when installing a new component.
Remove the washer pump.
er
ov
ec
itr
.b
w
w
w
Installation
1. To install, reverse the removal procedure.
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 5/6
8/1/2016 2015 Edge
om
.c
er
ov
ec
itr
.b
w
w
w
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 6/6
8/1/2016 2015 Edge
50116 Wipers and Washers 2015 Edge
Removal and Installation Procedure revision date: 04/28/2015
Windshield Wiper Motor
Base Part Number: 17508
Removal
NOTE: Removal steps in this procedure may contain installation details.
NOTE: LH shown, RH similar.
NOTE: Hood removed in this procedure for clarity.
1. Remove the cowl panel.
Refer to: Cowl Panel (50102 Front End Body Panels, Removal and Installation).
2. Detach the wire harness retainer and disconnect the wiper motor electrical connector.
om
.c
er
ov
ec
itr
.b
w
w
w
3. Remove the bolts and the windshield wiper motor.
Torque: 62 lb.in (7 Nm)
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 1/3
8/1/2016 2015 Edge
om
.c
4. NOTE: This step is only necessary when installing a new component.
er
NOTE: This step is only necessary if the wiper motor mount grommet remains in the square locator hole after the
ov
wiper motor has been removed.
Remove the wiper motor mount grommet.
ec
itr
.b
w
w
w
Installation
1. To install, reverse the removal procedure.
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 2/3
8/1/2016 2015 Edge
om
.c
er
ov
ec
itr
.b
w
w
w
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 3/3
8/1/2016 2015 Edge
50116 Wipers and Washers 2015 Edge
Removal and Installation Procedure revision date: 01/30/2015
Windshield Wiper Pivot Arm
Special Tool(s) / General Equipment
Two Leg Puller
Removal
NOTE: Hood removed in this procedure for clarity.
1. Remove the wiper pivot arm nut cover(s).
om
.c
er
ov
ec
itr
.b
w
w
w
2. Remove the wiper pivot arm nut(s).
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 1/4
8/1/2016 2015 Edge
om
.c
er
3. NOTICE: Failure to use a two leg puller may result in broken wiper motor bracket legs.
Remove the wiper pivot arm(s).
ov
Use the General Equipment: Two Leg Puller
ec
itr
.b
w
w
w
Installation
1. NOTICE: The ignition switch must be set to the ON position. Power is required to hold the wiper motor in
the PARK position. No power or low battery voltage will allow the motor to move from the PARK position
during the torquing operation resulting in incorrect wiper arm position.
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 2/4
8/1/2016 2015 Edge
Verify the windshield wiper motor is in the PARK position.
1. Set the ignition switch to the ON position.
2. Pull the wiper switch down to cycle the windshield wiper motor.
om
.c
er
ov
2. NOTE: LH windshield wiper blade is always positioned above the RH windshield wiper blade.
ec
Install the wiper pivot arm(s).
itr
1. Align the wiper blade(s) within the marks on the windshield.
2. Install the wiper pivot arm nut(s).
Torque: 18 lb.ft (25 Nm)
.b
w
w
w
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 3/4
8/1/2016 2015 Edge
3. Install the wiper pivot arm nut cover(s).
om
.c
er
ov
ec
itr
.b
w
w
w
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 4/4
8/1/2016 2015 Edge
50116 Wipers and Washers 2015 Edge
Description and Operation Procedure revision date: 02/2/2015
Wipers and Washers Overview
Overview
The windshield wiper/washer system is activated by the wiper/washer switch. The following functions/features of the
windshield wiper/washer system are:
Mist wipe
Windshield wash (includes camera wash, if equipped)
Courtesy wipe
Windshield wipers (low/high speed)
Intermittent wipers
Speed dependent wipers
Wiper activated exterior lamps
Rain sensitive wipers (if equipped)
om
There are 6 intermittent/sensitivity settings to choose from for the intermittent/rain sensitive wipers.
.c
er
ov
ec
itr
.b
w
w
w
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 1/1
8/1/2016 2015 Edge
50116 Wipers and Washers 2015 Edge
Description and Operation Procedure revision date: 02/2/2015
Wipers and Washers System Operation and Component Description
System Operation
System Diagram
om
.c
er
ov
ec
Network Message Chart
SCCM Network Input Messages
itr
.b
feature configuration courtesy wipe and the rain sensitive wiper features.
BCM Network Input Messages
Windshield Wipers
The wiper relay, integrated into the BJB, is energized when the ignition is on providing voltage to the windshield wiper
motor assemblies, the rain sensor (if equipped), and the rear window wiper motor assembly.
The SCCM monitors the wiper/washer switch inputs and sends the wiper/washer switch data to the driver side
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 1/5
8/1/2016 2015 Edge
windshield wiper motor assembly through a LIN. The driver side windshield wiper motor assembly then synchronizes
wiper operation with the passenger side windshield wiper motor assembly (using an isolated communication circuit
between them) to prevent interference, or outofphase operation between the windshield wiper motor assemblies while
they are cycling. The driver side windshield wiper motor assembly is the primary wiper motor and controls the operation of
both windshield wipers.
Based on the input, the driver side windshield wiper motor assembly activates the appropriate wash, low, high and
intermittent or rain sense modes. The logic for wiper system operation is a function of the ECU in the driver side
windshield wiper motor assembly.
When the wiper/washer switch is in the high speed setting, the driver side windshield wiper motor assembly also receives
a ground signal directly from the SCCM (bypassing the logic within the module). This failsafe circuit makes sure the
windshield wipers function in high speed mode in the event of a LIN communication failure.
Mist Wipe
When the mist wipe function is activated, the SCCM sends the request to the driver side windshield wiper motor
assembly over the LIN to perform a single wipe of the windshield. The windshield wipers operate for as long as the mist
wipe function is active.
Windshield Washer
om
When the wiper/washer switch is activated, the SCCM sends the washer request to the driver side windshield wiper
motor assembly over the LIN. The windshield wash relay is internal to the driver side windshield wiper motor assembly.
When the driver side windshield wiper motor asembly activates the internal windshield wash relay, voltage is provided to
.c
the washer pump, directing washer fluid to the windshield. If equipped with a front camera, washer solvent is also
directed to the front camera lens when the washer pump is active. When the switch is released, the windshield wiper
motors will continue to activate for 3 additional wipes and then turn off.
er
Ground for the washer pump is provided through the rear window washer relay located within the BJB.
ov
Courtesy Wipe
ec
If the wiper/washer switch is off when the when the windshield washer is requested, a few seconds after the windshield
wash cycle has completed, an additional wipe of the windshield occurs to clear any remaining fluid that remains on the
windshield.
itr
Intermittent Wipers
.b
When the wiper/washer switch is in an intermittent setting, the windshield wiper motors activate at timed intervals. The
lower the setting, the longer the interval between wipes.
w
Speed Dependent Wipers
w
When the wiper/washer switch is in any intermittent setting except the lowest setting, the speed dependent feature
w
increases the frequency of wiping as the vehicle speed increases to compensate for the extra moisture that accumulates
on the windshield.
The SCCM receives the vehicle speed from the PCM. The SCCM then sends the vehicle speed data to the driver side
windshield wiper motor assembly through the LIN.
Rain Sensitive Wipers (if equipped)
When equipped, the rain sensitive wiper feature replaces the intermittent wiper feature. The rain sensitive feature is active
when the wiper/washer switch is in any of the 6 auto/intermittent sensitivity settings. The setting closest to OFF is the
least sensitive to moisture, the highest setting being the most sensitive to moisture.
The rain sensor sends data through the LIN to the driver side windshield wiper motor assembly. Based on the data
received from the rain sensor and the auto/intermittent setting from the wiper/washer switch, the system automatically
activates and adjusts the wiper speed and frequency when moisture is detected on the windshield.
If a fault is detected with the rain sensitive feature, the windshield wipers change to a default intermittent mode. The
timing of the wipers correspond to a standard intermittent setting based on the auto/intermittent sensitivity setting on the
wiper/washer switch.
Wiper Activated Exterior Lamps
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 2/5
8/1/2016 2015 Edge
The BCM turns the exterior lamps on within 10 seconds of the windshield wipers being activated by the wiper/washer
switch when the headlamp switch is in the AUTO position. Approximately 30 seconds after the windshield wipers turn off,
the BCM turns the exterior lamps off.
If equipped with rain sensitive wipers, the BCM turns the exterior lamps on when the rain sensitive wipers are activated
by moisture detected on the windshield when the headlamp switch is in the AUTO position. Shortly after the rain
sensitive wipers are deactivated (moisture no longer detected on the windshield), the BCM turns the exterior lamps off.
Rear Window Wiper
When the wiper/washer switch is in the INT 1 or INT 2 (continuous wipe) position, the SCCM sends the request to the
driver side windshield wiper motor assembly through the LIN. When the request is received, the windshield wiper motor
momentarily supplies ground to the rear window wiper motor, activating the motor. The position of the wiper/washer
switch determines how many times per minute the windshield wiper motor provides ground to activate the rear window
wiper motor.
The rear window wiper motor is selfparking.
Rear Window Washer
When the rear window washer switch is activated, the SCCM sends the request to the driver side windshield wiper motor
om
assembly through the LIN. The driver side windshield wiper motor assembly energizes the rear washer relay (located in
the BJB) and activates the rear window wiper motor. When the driver side windshield wiper motor assembly activates the
rear window wash relay, voltage is provided to the washer pump, directing washer fluid to the rear window. When the
switch is released, the rear window wiper motor continues to operate for 3 additional wipes and then turns off.
.c
Ground for the washer pump is provided through the windshield washer relay within the driver side windshield wiper motor
assembly.
Component Description
er
ov
Wiper/Washer Switch
ec
The wiper/washer switch is mounted directly to the SCCM. The windshield wiper/washer inputs to the SCCM are:
itr
Mist wipe
Windshield wash
Off
.b
AUTO 1/INT 1
AUTO 2/INT 2
w
AUTO 3/INT 3
AUTO 4/INT 4
w
AUTO 5/INT 5
AUTO 6/INT 6
w
Low
High
The rear wiper/washer inputs to the SCCM are:
Off
INT 1
INT 2 (continuous wipe)
Rear window wash
Windshield Wiper Motor
Both windshield wiper motor assemblies contain an ECU, internal Halleffect sensors to monitor the wiper arm position
and a multispeed motor. The ECU in the driver side windshield wiper motor assembly continuously monitors the
wiper/washer switch inputs from the SCCM and (if equipped) the rain sensor when the ignition is on. Based on input from
the wiper/washer switch, the ECU in the driver side windshield wiper motor assembly energizes the internal driver side
motor to achieve the requested wiper mode, and simultaneously transmits a message indicating speed and position of the
internal driver side motor over a dedicated serial communication interface circuit to the ECU in the passenger side
windshield wiper motor assembly. The ECU in the passenger side windshield motor assembly will simultaneously
energize the internal passenger side motor to match the speed and relative position of the driver side motor based on the
message recieved from the ECU in the driver side wiper motor assembly.
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 3/5
8/1/2016 2015 Edge
The driver side windshield wiper motor assembly contains the primary ECU for the windshield wiper system, and controls
the operation of both windshield wipers.
The wiper arms are mounted directly to the wiper motors.
Washer Pump
The washer pump is controlled by the driver side windshield wiper motor assembly. The front and rear washer system
share the same washer reservoir and a bidirectional washer pump. The washer pump delivers washer fluid to the
windshield when the ECU in the driver side windshield wiper motor assembly activates the internal windshield washer
relay, which provides voltage to the washer pump. Ground for the washer pump is provided through the rear washer relay
(located in the BJB). When activated, the washer pump delivers washer fluid to the windshield.
When the driver side windshield wiper motor assembly energizes the rear washer relay, the rear washer relay provides
voltage to the washer pump. Ground for the washer pump is provided through the windshield washer relay (internal to the
driver side windshield wiper motor assembly). When activated, the pump delivers washer fluid to the rear window.
Rain Sensor
The rain sensor uses an infrared beam to optically sense water on the windshield. The intensity of the reflected beam is
measured and compared to the intensity of the transmitted beam. If there is water on the surface of the windshield, the
om
beam distorts, reducing the intensity of the beam. If the beam is not reflected completely, it is interpreted as rain on the
windshield and the windshield wipers are activated.
A geltype lens is used as the interface between the rain sensor and the windshield. If the lens is missing or damaged,
.c
the rain sensing wipers can be inoperative. The rain sensor geltype lens cannot be replaced separately on a rain sensor
of this type.
Rear Wiper Motor
er
ov
The rear window wiper motor assembly contains an integrated relay and a single speed motor. When the windshield wiper
motor momentarily energizes the integrated relay within the rear wiper motor, the rear window wiper activates. The
integrated relay is used to continue the rear window wipe and park the wiper motor.
ec
itr
.b
w
w
w
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 4/5
8/1/2016 2015 Edge
om
.c
er
ov
ec
itr
.b
w
w
w
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 5/5
8/1/2016 2015 Edge
50116 Wipers and Washers 2015 Edge
Diagnosis and Testing Procedure revision date: 10/19/2015
Wipers and Washers
DTC Chart: BCM
Diagnostics in this manual assume a certain skill level and knowledge of Fordspecific diagnostic practices.
REFER to: Diagnostic Methods (10000 General Information, Description and Operation).
BCM DTC Chart
om
B130F:14 Run Accessory Control: Circuit If the windshield wipers are inoperative, GO to Pinpoint
Short To Ground or Open Test A
If the windshield wipers operate with the ignition off,
.c
GO to Pinpoint Test D
B10AD:9A Rain Sensor: Component or
System Operating Conditions er
DIAGNOSE the symptom present with the wiper/washer
system. REFER to the Symptom Chart in this section.
ov
All other Diagnostic
Trouble Codes (DTCs) REFER to: Body Control Module (BCM) (41910 Multifunction
Electronic Modules, Diagnosis and Testing).
ec
itr
DTC Chart: SCCM
.b
Diagnostics in this manual assume a certain skill level and knowledge of Fordspecific diagnostic practices.
REFER to: Diagnostic Methods (10000 General Information, Description and Operation).
w
w
SCCM DTC Chart
w
om
B10AD:49 Rain Sensor: Internal INSTALL a new rain sensor.
Electronic Failure REFER to: Rain Sensor (50116 Wipers and Washers, Removal
and Installation).
.c
B10AD:55 Rain Sensor: Not Configured CARRY OUT the Programmable Module Installation (PMI) for the
SCCM using as built data.
B1131:01 Wiper motor module: General GO to Pinpoint Test B
Electrical Failure
er
ov
B1131:02 Wiper motor module: General GO to Pinpoint Test B
Signal Failure
ec
Operating Conditions
B1131:11 Wiper motor module: Circuit GO to Pinpoint Test B
w
Short To Ground
w
REFER to: Windshield Wiper Motor (50116 Wipers and
Washers, Removal and Installation).
If both wiper motors are inoperative, INSTALL a new driver
side windshield wiper motor.
REFER to: Windshield Wiper Motor (50116 Wipers and
Washers, Removal and Installation).
All other
Diagnostic Trouble REFER to: Steering Wheel and Column Electrical Components
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 2/42
8/1/2016 2015 Edge
Diagnostic Trouble REFER to: Steering Wheel and Column Electrical Components
Codes (DTCs) (21105 Steering Wheel and Column Electrical Components,
Diagnosis and Testing).
Symptom Chart
Symptom Chart: Wiper and Washer
Diagnostics in this manual assume a certain skill level and knowledge of Fordspecific diagnostic practices.
REFER to: Diagnostic Methods (10000 General Information, Description and Operation).
Symptom Chart
om
The intermittent and/or low speed windshield wipers are inoperative Refer to the GO to Pinpoint
Pinpoint Test Test B
.c
The high speed windshield wipers are inoperative Refer to the GO to Pinpoint
er Pinpoint Test Test C
ov
The windshield wipers stay on continuously Refer to the GO to Pinpoint
Pinpoint Test Test D
ec
Pinpoint Tests
All Windshield Wiper Modes Are Inoperative From One Or Both Windshield Wiper Motors
Refer to Wiring Diagrams Cell 81 for schematic and connector information.
Normal Operation and Fault Conditions
om
REFER to: Wipers and Washers System Operation and Component Description (50116 Wipers and Washers,
Description and Operation).
.c
BCM DTC Fault Trigger Conditions
er
ov
DTC Description Fault Trigger Conditions
B130F:12 Run Accessory Control: Circuit Short To Sets when the BCM detects a short to voltage from the wiper
ec
Battery relay control circuit.
B130F:14 Run Accessory Control: Circuit Short To Sets when the BCM detects an open from the wiper relay
itr
Ground or Open control circuit.
.b
Possible Sources
w
Fuse
w
Wiring, terminals or connectors
BJB
w
Windshield wiper motor
SCCM
BCM
Visual Inspection and Diagnostic Prechecks
Inspect BJB fuses 83 (25A) and 1 (25A) and make sure they are OK.
PINPOINT TEST A : ALL WINDSHIELD WIPER MODES ARE INOPERATIVE FROM ONE OR BOTH
WINDSHIELD WIPER MOTORS
A1 CHECK THE DRIVER SIDE WINDSHIELD WIPER MOTOR OPERATION
Ignition ON.
Cycle the wiper/washer switch from off through to the low speed setting, and then back to off.
Does the driver side windshield wiper motor operate?
Yes VERIFY the BJB fuse 1 (25A) is OK. If OK, GO to A2
If not OK, REFER to the Wiring Diagrams manual to identify the possible causes of the circuit
short.
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 4/42
8/1/2016 2015 Edge
short.
No VERIFY the BJB fuse 83 (25A) is OK. If OK, GO to A8
If not OK, REFER to the Wiring Diagrams manual to identify the possible causes of the circuit
short.
A2 CHECK FOR VOLTAGE TO THE PASSENGER SIDE WINDSHIELD WIPER MOTOR
Ignition OFF.
Disconnect Passenger Side Windshield Wiper Motor C1656.
Ignition ON.
Measure:
Click to display connectors
Positive Lead Measurement / Action Negative Lead
C16561 Ground
om
Is the voltage greater than 11 volts?
Yes GO to A4
.c
No GO to A3
er
ov
A3 CHECK THE PASSENGER SIDE WINDSHIELD WIPER MOTOR VOLTAGE SUPPLY CIRCUIT FOR AN
OPEN
Ignition OFF.
ec
Disconnect BJB C1035B.
Measure:
itr
Click to display connectors
.b
Is the resistance less than 3 ohms?
w
Yes INSTALL a new BJB.
No REPAIR the circuit.
A4 CHECK THE PASSENGER SIDE WINDSHIELD WIPER MOTOR GROUND CIRCUIT FOR AN OPEN
Ignition OFF.
Measure:
Click to display connectors
Positive Lead Measurement / Action Negative Lead
C16562 Ground
Is the resistance less than 3 ohms?
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 5/42
8/1/2016 2015 Edge
Yes GO to A5
No REPAIR the circuit.
A5 CHECK THE WIPER MOTOR COMMUNICATION CIRCUIT FOR A SHORT TO VOLTAGE
Disconnect Driver Side Windshield Wiper Motor C1655.
Ignition ON.
Measure:
Click to display connectors
Positive Lead Measurement / Action Negative Lead
C16563 Ground
Is any voltage present?
om
Yes REPAIR the circuit.
No GO to A6
.c
A6 CHECK THE WIPER MOTOR COMMUNICATION CIRCUIT FOR A SHORT TO GROUND
Ignition OFF.
er
ov
Measure:
Click to display connectors
ec
C16563 Ground
.b
Is the resistance greater than 10,000 ohms?
w
w
Yes GO to A7
No REPAIR the circuit.
w
A7 CHECK THE WIPER MOTOR COMMUNICATION CIRCUIT FOR AN OPEN
Measure:
Click to display connectors
Positive Lead Measurement / Action Negative Lead
C16563 C16553
Is the resistance less than 3 ohms?
Yes INSTALL a new passenger side windshield wiper motor.
REFER to: Windshield Wiper Motor (50116 Wipers and Washers, Removal and Installation).
TEST the system for normal operation. If the concern is still present, INSTALL a new driver side
windshield wiper motor.
REFER to: Windshield Wiper Motor (50116 Wipers and Washers, Removal and Installation).
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 6/42
8/1/2016 2015 Edge
REFER to: Windshield Wiper Motor (50116 Wipers and Washers, Removal and Installation).
No REPAIR the circuit.
A8 CHECK FOR BCM (BODY CONTROL MODULE) DTC (DIAGNOSTIC TROUBLE CODE) B130F:12 OR
B130F:14
Using a diagnostic scan tool, perform the BCM selftest.
Is DTC B130F:12 or B130F:14 present?
Yes For DTC B130F:12, GO to A9
For DTC B130F:14, GO to A10
No GO to A12
A9 CHECK THE WIPER RELAY CONTROL CIRCUIT FOR A SHORT TO VOLTAGE
om
Ignition OFF.
Disconnect BCM C2280C.
Disconnect BJB C1035A.
Ignition ON.
.c
Measure:
Click to display connectors
Positive Lead Measurement / Action er Negative Lead
ov
C1035A35 Ground
ec
Is any voltage present?
itr
Yes REPAIR the circuit.
.b
No INSTALL a new BJB. CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the selftest.
w
If DTC B130F:12 is retrieved again, GO to A20
w
w
A10 CHECK FOR VOLTAGE TO THE BCM (BODY CONTROL MODULE)
Ignition OFF.
Disconnect BCM C2280C.
Measure:
Click to display connectors
Positive Lead Measurement / Action Negative Lead
C2280C24 Ground
Is the voltage greater than 11 volts?
Yes GO to A20
No GO to A11
A11 CHECK THE WIPER RELAY CONTROL CIRCUIT FOR AN OPEN
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 7/42
8/1/2016 2015 Edge
A11 CHECK THE WIPER RELAY CONTROL CIRCUIT FOR AN OPEN
Disconnect BJB C1035B.
Measure:
Click to display connectors
Positive Lead Measurement / Action Negative Lead
C2280C24 C1035B37
Is the resistance less than 3 ohms?
Yes INSTALL a new BJB.
No REPAIR the circuit.
om
A12 CHECK THE INPUT TO THE SCCM (STEERING COLUMN CONTROL MODULE)
Using a diagnostic scan tool, view the SCCM Parameter Identifications (PIDs).
Using a diagnostic scan tool, view the following SCCM wiper/washer switch Parameter Identifications (PIDs):
.c
WIPE_SINGLE
F_WASH_SW
F_WIP_INT_D1
F_WIP_INT_D2
F_WIP_INT_D3 er
ov
F_WIP_INT_D4
F_WIP_INT_D5
F_WIP_INT_D6
ec
F_WIP_SLO_SW
F_WIPE_FAST_SW
itr
Cycle the wiper/washer switch from off to the high speed setting and then back to off.
Do the Parameter Identifications (PIDs) correspond correctly with each setting selection?
.b
Yes GO to A13
w
No INSTALL a new wiper/washer switch.
w
REFER to: Steering Column Multifunction Switch RH (21105 Steering Wheel and Column
Electrical Components, Removal and Installation).
w
TEST the system for normal operation. If the concern is still present, INSTALL a new SCCM.
REFER to: Steering Column Control Module (SCCM) (21105 Steering Wheel and Column
Electrical Components, Removal and Installation).
A13 ISOLATE THE PASSENGER SIDE WIPER MOTOR
Ignition OFF.
Disconnect Passenger Side Windshield Wiper Motor C1656.
Ignition ON.
Cycle the wiper/washer switch from off to the low speed setting and then back to off.
Does the driver side windshield wiper motor operate?
Yes INSTALL a new passenger windshield wiper motor.
REFER to: Windshield Wiper Motor (50116 Wipers and Washers, Removal and Installation).
No GO to A14
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 8/42
8/1/2016 2015 Edge
A14 CHECK FOR VOLTAGE TO THE DRIVER SIDE WINDSHIELD WIPER MOTOR
Ignition OFF.
Disconnect Driver Side Windshield Wiper Motor C1655.
Ignition ON.
Measure:
Click to display connectors
Positive Lead Measurement / Action Negative Lead
C16558 Ground
Is the voltage greater than 11 volts?
Yes GO to A16
No GO to A15
om
A15 CHECK THE DRIVER SIDE WINDSHIELD WIPER MOTOR VOLTAGE CIRCUIT FOR AN OPEN
.c
Ignition OFF.
Disconnect BJB C1035A.
Measure:
er
ov
Click to display connectors
Positive Lead Measurement / Action Negative Lead
ec
C16558 C1035A1
itr
Is the resistance less than 3 ohms?
.b
Yes INSTALL a new BJB.
w
No REPAIR the circuit.
w
w
A16 CHECK THE WINDSHIELD WIPER MOTOR GROUND CIRCUIT FOR AN OPEN
Ignition OFF.
Measure:
Click to display connectors
Positive Lead Measurement / Action Negative Lead
C16556 Ground
Is the resistance less than 3 ohms?
Yes GO to A17
No REPAIR the circuit.
A17 CHECK THE FAILSAFE HIGH SPEED WIPER GROUND CIRCUIT CONTROL
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 9/42
8/1/2016 2015 Edge
A17 CHECK THE FAILSAFE HIGH SPEED WIPER GROUND CIRCUIT CONTROL
NOTICE: The following Pinpoint Test uses a test lamp to simulate normal circuit loads. Use only a Rotunda
Test Lamp (SGT27000) or 250300mA incandescent bulb test lamp. To avoid connector terminal damage,
use the Rotunda Flex Probe kit for the test lamp probe connection to the vehicle. Do not use the test lamp
probe directly on any connector.
Connect:
Click to display connectors
Positive Lead Measurement / Action Negative Lead
C16551 C16558
Ignition ON.
Place the wiper/washer switch to the high speed setting.
Does the test lamp illuminate?
Yes INSTALL a new driver side windshield wiper motor.
om
REFER to: Windshield Wiper Motor (50116 Wipers and Washers, Removal and Installation).
No GO to A18
.c
A18 CHECK THE FAILSAFE HIGH SPEED WIPER GROUND CIRCUIT FOR AN OPEN
er
ov
NOTE: If steps A1A17 did not identify the cause of the concern, a double fault is present. After the failsafe
ground is diagnosed and repaired, it is necessary check all operation modes and diagnose any symptom still
present.
ec
Ignition OFF.
Disconnect SCCM C226A.
itr
Measure:
Click to display connectors
.b
C16551 C226A2
w
w
Is the resistance less than 3 ohms?
Yes INSTALL a new wiper/washer switch.
REFER to: Steering Column Multifunction Switch RH (21105 Steering Wheel and Column
Electrical Components, Removal and Installation).
TEST the system for normal operation. If the concern is still present, GO to A19
No REPAIR the circuit.
A19 CHECK FOR CORRECT SCCM (STEERING COLUMN CONTROL MODULE) OPERATION
Disconnect and inspect all the SCCM connectors:
Repair:
corrosion (install new connector or terminals – clean module pins)
damaged or bent pins – install new terminals/pins
pushedout pins – install new pins as necessary
Reconnect the SCCM connectors. Make sure they seat and latch correctly.
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 10/42
8/1/2016 2015 Edge
Is the concern still present?
Yes CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this
concern, DISCONTINUE this test and FOLLOW the TSB instructions. If no Technical Service
Bulletins (TSBs) address this concern, INSTALL a new SCCM.
REFER to: Steering Column Control Module (SCCM) (21105 Steering Wheel and Column
Electrical Components, Removal and Installation).
No The system is operating correctly at this time. The concern may have been caused by module
connections. ADDRESS the root cause of any connector or pin issues.
A20 CHECK FOR CORRECT BCM (BODY CONTROL MODULE) OPERATION
Disconnect and inspect all the BCM connectors:
Repair:
corrosion (install new connector or terminals – clean module pins)
damaged or bent pins – install new terminals/pins
pushedout pins – install new pins as necessary
Reconnect the BCM connectors. Make sure they seat and latch correctly.
om
Is the concern still present?
Yes
.c
Click here to access Guided Routine (BCM).
er
No The system is operating correctly at this time. The concern may have been caused by module
connections. ADDRESS the root cause of any connector or pin issues.
ov
ec
The Intermittent And/Or Low Speed Windshield Wipers Are Inoperative
itr
Refer to Wiring Diagrams Cell 81 for schematic and connector information.
.b
Normal Operation and Fault Conditions
w
REFER to: Wipers and Washers System Operation and Component Description (50116 Wipers and Washers,
w
Description and Operation).
w
SCCM DTC Fault Trigger Conditions
Possible Sources
Wiring, terminals or connectors
Wiper/washer switch
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 11/42
8/1/2016 2015 Edge
Driver side windshield wiper motor
Rain sensor
SCCM
Visual Inspection and Diagnostic Prechecks
Inspect the wiper/washer switch for damage.
PINPOINT TEST B : THE INTERMITTENT AND/OR LOW SPEED WINDSHIELD WIPERS ARE INOPERATIVE
NOTE: It may be necessary to disconnect and then reconnect the battery after the repair to enable the wiper
operation.
B1 CHECK THE HIGH SPEED WIPER OPERATION
Ignition ON.
Place the wiper/washer switch to the high speed setting and observe the windshield wipers. Place the
wiper/washer switch to the off setting.
Do the windshield wipers operate with the wiper/washer switch in the high speed setting?
om
Yes GO to B2
No GO to Pinpoint Test A
.c
B2 CHECK THE LOW SPEED WIPER OPERATION
er
Place the wiper/washer switch to the low speed setting and observe the windshield wipers. Place the
ov
wiper/washer switch to the off setting.
Do the windshield wipers operate with the wiper/washer switch in the low speed setting?
ec
Yes If not equipped with a rain sensor, GO to Pinpoint Test E
If equipped with a rain sensor, GO to Pinpoint Test F
itr
No GO to B3
.b
w
B3 CHECK THE INPUT TO THE SCCM (STEERING COLUMN CONTROL MODULE)
w
Using a diagnostic scan tool, view the SCCM Parameter Identifications (PIDs).
Using a diagnostic scan tool, view the following SCCM F_WIP_SLO_SW PID.
w
Place the wiper/washer switch to the low speed setting.
Does the PID indicate the wiper/washer switch is in the low speed setting?
Yes If equipped with a rain sensor, GO to B4
If not equipped with a rain sensor, GO to B5
No INSTALL a new wiper/washer switch.
REFER to: Steering Column Multifunction Switch RH (21105 Steering Wheel and Column
Electrical Components, Removal and Installation).
TEST the system for normal operation. If the concern is still present, INSTALL a new SCCM.
REFER to: Steering Column Control Module (SCCM) (21105 Steering Wheel and Column
Electrical Components, Removal and Installation).
B4 ISOLATE THE RAIN SENSOR
Ignition OFF.
Disconnect Rain Sensor C9805.
Ignition ON.
Place the wiper/washer switch to the low speed setting and observe the windshield wipers. Place the
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 12/42
8/1/2016 2015 Edge
Place the wiper/washer switch to the low speed setting and observe the windshield wipers. Place the
wiper/washer switch to the off setting.
Do the windshield wipers operate with the wiper/washer switch in the low speed setting?
Yes INSTALL a new rain sensor.
REFER to: Rain Sensor (50116 Wipers and Washers, Removal and Installation).
No GO to B5
B5 CHECK THE LIN (LOCAL INTERCONNECT NETWORK) CIRCUIT FOR A SHORT TO VOLTAGE
Ignition OFF.
Disconnect Driver Side Windshield Wiper Motor C1655..
Disconnect SCCM C266A..
Ignition ON.
Measure:
Click to display connectors
om
Positive Lead Measurement / Action Negative Lead
C16554 Ground
.c
Is any voltage present?
er
ov
Yes REPAIR the circuit.
No GO to B6
ec
itr
B6 CHECK THE LIN (LOCAL INTERCONNECT NETWORK) CIRCUIT FOR A SHORT TO GROUND
Ignition OFF.
.b
Measure:
w
Click to display connectors
Positive Lead Measurement / Action Negative Lead
w
C16554 Ground
w
Is the resistance greater than 10,000 ohms?
Yes GO to B7
No REPAIR the circuit.
B7 CHECK THE LIN (LOCAL INTERCONNECT NETWORK) CIRCUIT FOR AN OPEN
Measure:
Click to display connectors
Positive Lead Measurement / Action Negative Lead
C16554 C2414A8
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 13/42
8/1/2016 2015 Edge
Is the resistance less than 3 ohms?
Yes INSTALL a new driver side windshield wiper motor.
REFER to: Windshield Wiper Motor (50116 Wipers and Washers, Removal and Installation).
TEST the system for normal operation. If the concern is still present, GO to B8
No REPAIR the circuit.
B8 CHECK FOR CORRECT SCCM (STEERING COLUMN CONTROL MODULE) OPERATION
Disconnect and inspect all the SCCM connectors.
Repair:
corrosion (install new connector or terminal clean module pins)
damaged or bent pins install new terminals/pins
pushedout pins install new pins as necessary
Reconnect the SCCM connectors. Make sure it seats and latches correctly.
Operate the system and determine if the concern is still present.
om
Is the concern still present?
Yes CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this
.c
concern, DISCONTINUE this test and FOLLOW the TSB instructions. If no Technical Service
Bulletins (TSBs) address this concern, INSTALL a new SCCM.
er
REFER to: Steering Column Control Module (SCCM) (21105 Steering Wheel and Column
Electrical Components, Removal and Installation).
ov
No The system is operating correctly at this time. The concern may have been caused by a loose or
corroded connector. ADDRESS the root cause of any connector or pin issues.
ec
itr
The High Speed Windshield Wipers Are Inoperative
.b
Normal Operation and Fault Conditions
w
w
REFER to: Wipers and Washers System Operation and Component Description (50116 Wipers and Washers,
Description and Operation).
w
Possible Sources
Driver side windshield wiper motor
Wiper/washer switch
SCCM
PINPOINT TEST C : THE HIGH SPEED WINDSHIELD WIPERS ARE INOPERATIVE
C1 CHECK THE INPUT TO THE SCCM (STEERING COLUMN CONTROL MODULE)
Ignition ON.
Using a diagnostic scan tool, view the SCCM Parameter Identifications (PIDs).
Using a diagnostic scan tool, view the SCCM F_WIPE_FAST_SW PID.
Place the wiper/washer switch to the high speed setting.
Does the PID indicate the wiper/washer switch is in the high speed setting?
Yes INSTALL a new driver side windshield wiper motor.
REFER to: Windshield Wiper Motor (50116 Wipers and Washers, Removal and Installation).
No INSTALL a new wiper/washer switch.
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 14/42
8/1/2016 2015 Edge
No INSTALL a new wiper/washer switch.
REFER to: Steering Column Multifunction Switch RH (21105 Steering Wheel and Column
Electrical Components, Removal and Installation).
TEST the system for normal operation. If the concern is still present, INSTALL a new SCCM.
REFER to: Steering Column Control Module (SCCM) (21105 Steering Wheel and Column
Electrical Components, Removal and Installation).
The Windshield Wipers Stay On Continuously
Refer to Wiring Diagrams Cell 81 for schematic and connector information.
Normal Operation and Fault Conditions
REFER to: Wipers and Washers System Operation and Component Description (50116 Wipers and Washers,
Description and Operation).
om
.c
BCM DTC Fault Trigger Conditions
DTC Description
B130F:14 Run Accessory Control: Circuit Short To
er Fault Trigger Conditions
Sets when the BCM detects a short to ground from the wiper
ov
Ground or Open relay control circuit.
ec
Possible Sources
itr
Wiring, terminals or connectors
Wiper/washer switch
.b
BJB
Driver side windshield wiper motor
w
SCCM
w
Visual Inspection and Diagnostic Prechecks
w
Inspect the wiper/washer switch for damage.
PINPOINT TEST D : THE WINDSHIELD WIPERS STAY ON CONTINUOUSLY
D1 CHECK THE WINDSHIELD WIPER OPERATION WITH THE IGNITION OFF
Ignition OFF.
Observe the windshield wiper operation.
Do the windshield wipers operate with the ignition off?
Yes GO to D4
No GO to D2
D2 CHECK THE WINDSHIELD WIPER OPERATION WITH THE SCCM (STEERING COLUMN CONTROL
MODULE) DISCONNECTED
Ignition OFF.
Disconnect SCCM C226A.
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 15/42
8/1/2016 2015 Edge
Disconnect SCCM C226A.
Ignition ON.
Observe the windshield wiper operation.
Do the windshield wipers continue to operate?
Yes GO to D3
No INSTALL a new wiper/washer switch.
REFER to: Steering Column Multifunction Switch RH (21105 Steering Wheel and Column
Electrical Components, Removal and Installation).
TEST the system for normal operation. If the concern is still present, GO to D10
D3 CHECK THE HIGH SPEED FAILSAFE CIRCUIT FOR A SHORT TO GROUND
Ignition OFF.
Disconnect Driver Side Windshield Wiper Motor C1655.
Measure:
om
Click to display connectors
Positive Lead Measurement / Action Negative Lead
C16551 Ground
.c
Is the resistance greater than 10,000 ohms? er
ov
Yes INSTALL a new driver side windshield wiper motor.
ec
REFER to: Windshield Wiper Motor (50116 Wipers and Washers, Removal and Installation).
No REPAIR the circuit.
itr
.b
D4 CHECK FOR BCM (BODY CONTROL MODULE) DTC (DIAGNOSTIC TROUBLE CODE) B130F:14
Ignition ON.
w
Using a diagnostic scan tool, perform the BCM selftest.
w
Is DTC B130F:14 present?
w
Yes GO to D5
No If equipped with a rain sensor, GO to D7
If not equipped with a rain sensor, GO to D8
D5 ISOLATE THE BCM (BODY CONTROL MODULE)
Ignition OFF.
Disconnect BCM C2280C.
Measure:
Click to display connectors
Positive Lead Measurement / Action Negative Lead
C2280C24 Ground
Is the voltage greater than 11 volts?
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 16/42
8/1/2016 2015 Edge
Yes GO to D11
No GO to D6
D6 CHECK THE WIPER RELAY CONTROL CIRCUIT FOR A SHORT TO GROUND
Ignition OFF.
Disconnect BJB C1035B.
Measure:
Click to display connectors
Positive Lead Measurement / Action Negative Lead
C2280C24 Ground
Is the resistance greater than 10,000 ohms?
om
Yes INSTALL a new BJB.
No REPAIR the circuit.
.c
D7 CHECK THE RAIN SENSOR VOLTAGE SUPPLY CIRCUIT FOR A SHORT TO VOLTAGE er
ov
Ignition OFF.
Disconnect BJB C1035B.
Measure:
ec
Click to display connectors
itr
Is any voltage present?
w
w
Yes REPAIR the circuit.
No GO to D8
D8 CHECK THE DRIVER SIDE WINDSHIELD WIPER MOTOR VOLTAGE SUPPLY CIRCUIT FOR A
SHORT TO VOLTAGE
Measure:
Click to display connectors
Positive Lead Measurement / Action Negative Lead
C1035A1 Ground
Is any voltage present?
Yes REPAIR the circuit.
No GO to D9
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 17/42
8/1/2016 2015 Edge
No GO to D9
D9 CHECK THE PASSENGER SIDE WINDSHIELD WIPER MOTOR VOLTAGE SUPPLY CIRCUIT FOR A
SHORT TO VOLTAGE
Measure:
Click to display connectors
Positive Lead Measurement / Action Negative Lead
C1035A2 Ground
Is any voltage present?
Yes REPAIR the circuit.
No INSTALL a new BJB.
om
D10 CHECK FOR CORRECT SCCM (STEERING COLUMN CONTROL MODULE) OPERATION
.c
Disconnect and inspect all the SCCM connectors.
Repair:
corrosion (install new connector or terminal clean module pins)
damaged or bent pins install new terminals/pins er
ov
pushedout pins install new pins as necessary
Reconnect the SCCM connectors. Make sure they seat and latch correctly.
Operate the system and determine if the concern is still present.
ec
Is the concern still present?
itr
Yes CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this
concern, DISCONTINUE this test and FOLLOW the TSB instructions. If no Technical Service
.b
Bulletins (TSBs) address this concern, INSTALL a new SCCM.
REFER to: Steering Column Control Module (SCCM) (21105 Steering Wheel and Column
w
Electrical Components, Removal and Installation).
w
No The system is operating correctly at this time. The concern may have been caused by a loose or
corroded connector. ADDRESS the root cause of any connector or pin issues.
w
D11 CHECK FOR CORRECT BCM (BODY CONTROL MODULE) OPERATION
Disconnect and inspect all the BCM connectors.
Repair:
corrosion (install new connector or terminal clean module pins)
damaged or bent pins install new terminals/pins
pushedout pins install new pins as necessary
Reconnect the BCM connectors. Make sure they seat and latch correctly.
Operate the system and determine if the concern is still present.
Is the concern still present?
Yes
Click here to access Guided Routine (BCM).
No The system is operating correctly at this time. The concern may have been caused by a loose or
corroded connector. ADDRESS the root cause of any connector or pin issues.
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 18/42
8/1/2016 2015 Edge
The Windshield Wipers Do Not Operate Correctly In The Intermittent Mode
Normal Operation and Fault Conditions
REFER to: Wipers and Washers System Operation and Component Description (50116 Wipers and Washers,
Description and Operation).
Possible Sources
Wiper/washer switch
Driver side windshield wiper motor
SCCM
Visual Inspection and Diagnostic Prechecks
Inspect the wiper/washer switch for damage.
om
PINPOINT TEST E : THE WINDSHIELD WIPERS DO NOT OPERATE CORRECTLY IN THE INTERMITTENT
MODE
.c
E1 VERIFY IF THE VEHICLE IS EQUIPPED WITH A RAIN SENSOR
Inspect the vehicle for a rain sensor.
Is the vehicle equipped with a rain sensor? er
ov
Yes GO to E2
ec
No GO to E3
itr
E2 VERIFY THE RAIN SENSITIVE WIPER FEATURE IS DISABLED IN THE VEHICLE MESSAGE
.b
CENTER
Ignition ON.
w
Access the vehicle settings in the message center using the steering wheel controls and check the rain
sensitive feature setting.
w
Is the rain sensitive feature enabled?
w
Yes GO to Pinpoint Test F
No GO to E3
E3 CHECK THE LOW SPEED WIPER OPERATION
Ignition ON.
Place the wiper/washer switch to the low speed setting and observe the windshield wipers. Place the
wiper/washer switch to the off setting.
Do the low speed wipers operate when the low speed setting is selected?
Yes GO to E4
No GO to Pinpoint Test B
E4 CHECK THE INPUT FROM THE WIPER/ WASHER SWITCH
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 19/42
8/1/2016 2015 Edge
E4 CHECK THE INPUT FROM THE WIPER/ WASHER SWITCH
Using a diagnostic scan tool, view the SCCM Parameter Identifications (PIDs).
Using a diagnostic scan tool, view the following SCCM wiper/washer switch Parameter Identifications (PIDs):
F_WIP_INT_D1
F_WIP_INT_D2
F_WIP_INT_D3
F_WIP_INT_D4
F_WIP_INT_D5
F_WIP_INT_D6
Cycle the wiper/washer switch from off through each of the intermittent settings.
Do the PIDs correspond correctly with each setting selection?
Yes INSTALL a new driver side windshield wiper motor.
REFER to: Windshield Wiper Motor (50116 Wipers and Washers, Removal and Installation).
No INSTALL a new wiper/washer switch.
REFER to: Steering Column Multifunction Switch RH (21105 Steering Wheel and Column
Electrical Components, Removal and Installation).
om
TEST the system for normal operation. If the concern is still present, INSTALL a new SCCM.
REFER to: Steering Column Control Module (SCCM) (21105 Steering Wheel and Column
Electrical Components, Removal and Installation).
.c
The Rain Sensitive Wiper Feature Is Inoperative/Does Not Operate Correctly er
ov
Refer to Wiring Diagrams Cell 81 for schematic and connector information.
ec
Normal Operation and Fault Conditions
itr
REFER to: Wipers and Washers System Operation and Component Description (50116 Wipers and Washers,
Description and Operation).
.b
w
SCCM DTC Fault Trigger Conditions
w
w
Possible Sources
Fuse
Wiring, terminals or connectors
Rain sensitive feature not enabled
Foreign material on windshield, such as dirt, dust or bugs
Wiper blades
Windshield glass
Wiper/washer switch
Driver side windshield wiper motor
Rain sensor geltype lens
Rain sensor
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 20/42
8/1/2016 2015 Edge
SCCM
Visual Inspection and Diagnostic Prechecks
Inspect BJB fuse 3 (15A) and make sure it is OK.
Inspect the windshield for damage.
Inspect the rain sensor mounting for damage.
PINPOINT TEST F : THE RAIN SENSITIVE WIPER FEATURE IS INOPERATIVE/DOES NOT OPERATE
CORRECTLY
F1 CHECK THE LOW SPEED WIPER OPERATION
Ignition ON.
Place the wiper/washer switch to the low speed setting and observe the windshield wipers. Place the
wiper/washer switch to the off setting.
Do the low speed wipers operate when the low speed setting is selected?
Yes GO to F2
om
No GO to Pinpoint Test B
.c
F2 CHECK FOR DTC (DIAGNOSTIC TROUBLE CODE) B10AD:02 OR B10AD:08
Using a diagnostic scan tool, perform the SCCM selftest.
Are any Diagnostic Trouble Codes (DTCs) present? er
ov
Yes For DTC B10AD:02 or B10AD:08, GO to F11
ec
For all other Diagnostic Trouble Codes (DTCs), REFER to the SCCM DTC Chart in this
section.
No GO to F3
itr
.b
F3 VERIFY THE RAIN SENSITIVE WIPER FEATURE IS ENABLED IN THE VEHICLE MESSAGE CENTER
w
Access the vehicle settings in the message center using the steering wheel controls. Make sure the rain
sensitive feature is enabled.
w
Is the rain sensitive feature enabled?
w
Yes GO to F4
No ENABLE the rain sensitive feature. INFORM the customer how to enable/disable the rain
sensitive feature.
F4 CHECK THE INPUT FROM THE WIPER/WASHER SWITCH
Using a diagnostic scan tool, monitor the following SCCM wiper/washer switch PIDs:
F_WIP_INT_D1
F_WIP_INT_D2
F_WIP_INT_D3
F_WIP_INT_D4
F_WIP_INT_D5
F_WIP_INT_D6
Cycle the wiper/washer switch from off through each of the auto/intermittent sensitivity settings.
Do the Parameter Identifications (PIDs) correspond correctly with each setting selection?
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 21/42
8/1/2016 2015 Edge
Yes GO to F5
No INSTALL a new wiper/washer switch.
REFER to: Steering Column Multifunction Switch RH (21105 Steering Wheel and Column
Electrical Components, Removal and Installation).
TEST the system for normal operation. If the concern is still present, INSTALL a new SCCM.
REFER to: Steering Column Control Module (SCCM) (21105 Steering Wheel and Column
Electrical Components, Removal and Installation).
F5 CHECK THE WINDSHIELD FOR DAMAGE
Ignition OFF.
Inspect the windshield glass for any cracks, pits or other visible damage around the area of the rain sensor.
Is any windshield damage present near the area of the rain sensor?
Yes INSTALL a new windshield. REFER to: Windshield Glass (50111 Glass, Frames and
Mechanisms, Removal and Installation).
om
No GO to F6
.c
F6 CHECK THE WINDSHIELD GLASS FOR STREAKING
Ignition ON.
er
Turn the wiper/washer switch to the low speed wiper setting and while applying water to the windshield surface.
ov
Observe the wipe quality, especially around the area of the rain sensor.
Is any streaking present on the windshield around the area of the rain sensor?
ec
Yes GO to F7
itr
No GO to F9
.b
F7 CHECK THE WINDSHIELD WIPER BLADES FOR STREAKING
w
Ignition OFF.
w
Clean the windshield glass with glass cleaner.
Clean the wiper blades with isopropyl alcohol swabs. Wipe the entire length of the wiper blades.
w
Ignition ON.
Place the wiper/washer switch to the low speed wiper setting and while applying water to the windshield
surface. Observe the wipe quality, especially around the area of the rain sensor.
Was there noticeable improvement in the wipe quality after cleaning the glass and the wiper blades?
Yes GO to F8
No INSTALL new wiper blades. GO to F8
F8 RECHECK THE RAIN SENSITIVE WIPERS OPERATION
Place the wiper/washer switch to the auto/intermittent 5 setting (most sensitive to moisture) while applying
water on the windshield above the rain sensor.
Do the wipers operate when water is applied to the windshield surface?
Yes The system is operating correctly at this time. The concern may have been caused by poor wipe
quality on the windshield around the rain sensor.
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 22/42
8/1/2016 2015 Edge
quality on the windshield around the rain sensor.
No GO to F9
F9 CHECK FOR THE PRESENCE OF THE LENS GEL
Ignition OFF.
Lightly press the rain sensor against the windshield and release the rain sensor clips.
Does the rain sensor remain adhered to the windshield?
Yes ATTACH the retaining clips. GO to F10
No The sensor geltype lens is missing or damaged. INSTALL a new rain sensor.
REFER to: Rain Sensor (50116 Wipers and Washers, Removal and Installation).
F10 INSPECT THE RAIN SENSOR MOUNTING AREA
NOTE: The rain sensor geltype lens can be damaged or contaminated during rain sensor removal, rain sensor
om
bracket separation or incorrect installation.
From the outside of the vehicle, inspect the area of the windshield glass where the rain sensor is mounted. The
rain sensor contact area should appear black, with no bubbles, air pockets or contaminants between the
.c
windshield glass and the rain sensor.
er
Does the rain sensor contact area appear black, with no bubbles, air pockets or contaminants between the
windshield glass and the rain sensor?
ov
Yes GO to F11
ec
No REMOVE and INSTALL the rain sensor correctly.
REFER to: Rain Sensor (50116 Wipers and Washers, Removal and Installation).
itr
TEST the system for normal operation. If the concern is still present, INSTALL a new driver side
windshield wiper motor.
REFER to: Rear Window Wiper Motor (50116 Wipers and Washers, Removal and Installation).
.b
w
F11 CHECK FOR VOLTAGE TO THE RAIN SENSOR
w
Ignition OFF.
w
Disconnect Rain Sensor C9805.
Ignition ON.
Measure:
Click to display connectors
Positive Lead Measurement / Action Negative Lead
C98054 Ground
Is the voltage greater than 11 volts?
Yes GO to F13
No VERIFY BJB fuse 3 (15A) is OK. If OK, GO to F12
If not OK, REFER to the Wiring Diagrams manual to identify the possible causes of the circuit
short.
F12 CHECK THE RAIN SENSOR VOLTAGE SUPPLY CIRCUIT FOR AN OPEN
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 23/42
8/1/2016 2015 Edge
F12 CHECK THE RAIN SENSOR VOLTAGE SUPPLY CIRCUIT FOR AN OPEN
Ignition OFF.
Disconnect BJB C1035B.
Measure:
Click to display connectors
Positive Lead Measurement / Action Negative Lead
C98054 C1035B39
Is the resistance less than 3 ohms?
Yes INSTALL a new BJB.
No REPAIR the circuit.
om
F13 CHECK THE RAIN SENSOR GROUND CIRCUIT FOR AN OPEN
Ignition OFF.
Measure:
.c
Click to display connectors
C98056
Positive Lead Measurement / Action
er Ground
Negative Lead
ov
ec
Is the resistance less than 3 ohms?
itr
Yes GO to F14
.b
No REPAIR the circuit.
w
F14 CHECK THE LIN (LOCAL INTERCONNECT NETWORK) CIRCUIT FOR AN OPEN
w
Disconnect SCCM C226A.
w
Measure:
Click to display connectors
Positive Lead Measurement / Action Negative Lead
C98055 C226A8
Is the resistance less than 3 ohms?
Yes GO to F15
No REPAIR the circuit.
F15 CHECK FOR CORRECT SCCM (STEERING COLUMN CONTROL MODULE) OPERATION
Disconnect and inspect all the SCCM connectors.
Repair:
corrosion (install new connector or terminal clean module pins)
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 24/42
8/1/2016 2015 Edge
corrosion (install new connector or terminal clean module pins)
damaged or bent pins install new terminals/pins
pushedout pins install new pins as necessary
Reconnect all the SCCM connectors. Make sure they seat and latch correctly.
Operate the system and determine if the concern is still present.
Is the concern still present?
Yes CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this
concern, DISCONTINUE this test and FOLLOW the TSB instructions. If no Technical Service
Bulletins (TSBs) address this concern, INSTALL a new SCCM.
REFER to: Steering Column Control Module (SCCM) (21105 Steering Wheel and Column
Electrical Components, Removal and Installation).
No The system is operating correctly at this time. The concern may have been caused by a loose or
corroded connector. ADDRESS the root cause of any connector or pin issues.
om
The Windshield Wipers Do Not Park At The Correct Position
Normal Operation and Fault Conditions
.c
REFER to: Wipers and Washers System Operation and Component Description (50116 Wipers and Washers,
Description and Operation).
Possible Sources
er
ov
Wiper mounting arm and pivot shaft
Windshield wiper motor
ec
Visual Inspection and Diagnostic Prechecks
itr
Inspect the mounting arm and pivot shaft for damage.
.b
PINPOINT TEST G : THE WINDSHIELD WIPERS DO NOT PARK AT THE CORRECT POSITION
w
G1 CHECK THE WIPER MOUNTING ARM AND PIVOT SHAFT FOR DAMAGE
Ignition OFF.
w
Inspect the wiper mounting arm and pivot shaft for damage.
w
Is the wiper mounting arm and pivot shaft OK?
Yes GO to G2
No INSTALL a wiper mounting arm and pivot shaft.
REFER to: Windshield Wiper Pivot Arm (50116 Wipers and Washers, Removal and
Installation).
G2 CHECK THE WINDSHIELD WIPER PARK RELAY OPERATION
Ignition ON.
Place the wiper/washer switch to the low speed setting. When the wiper blades are in the middle of a wipe,
place the wiper/washer switch off.
Do the windshield wipers immediately stop when the wiper/washer switch is turned off?
Yes INSTALL a new driver side windshield wiper motor.
REFER to: Windshield Wiper Motor (50116 Wipers and Washers, Removal and Installation).
No ADJUST the pivot arms.
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 25/42
8/1/2016 2015 Edge
No ADJUST the pivot arms.
REFER to: Windshield Wiper Pivot Arm (50116 Wipers and Washers, Removal and
Installation).
The Windshield Washer Is Inoperative
Refer to Wiring Diagrams Cell 81 for schematic and connector information.
Normal Operation and Fault Conditions
REFER to: Wipers and Washers System Operation and Component Description (50116 Wipers and Washers,
Description and Operation).
Possible Sources
Wiring, terminals or connectors
om
Washer pump
Wiper/washer switch
Driver side windshield wiper motor
SCCM
.c
Visual Inspection and Diagnostic Prechecks
Inspect the wiper/washer switch for damage. er
ov
PINPOINT TEST H : THE WINDSHIELD WASHER IS INOPERATIVE
ec
NOTICE: Use the correct probe adapter(s) when making measurements. Failure to use the correct probe
adapter(s) may damage the connector.
itr
H1 CHECK THE AMBIENT AIR TEMPERATURE
Check the ambient air temperature.
.b
Is the ambient air temperature below freezing?
w
Yes GO to H2
w
No GO to H4
w
H2 CHECK THE WASHER SOLVENT
Check the washer solvent and make sure it is of the correct type to use for the temperature conditions present.
Is the correct type of washer solvent present?
Yes GO to H3
No ALLOW the vehicle to warm to room temperature. DRAIN and REFILL the windshield washer
reservoir with the correct washer solvent type. INFORM the customer of the correct type of
washer solvent to use for the temperature conditions present.
H3 CHECK FOR WASHER SOLVENT TO THE WASHER JETS
Disconnect the washer hoses from the windshield washer jets and place them in a container to capture fluid.
Ignition ON.
Momentarily activate the windshield washer function.
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 26/42
8/1/2016 2015 Edge
Momentarily activate the windshield washer function.
Is washer fluid emitted at the washer hoses?
Yes INSTALL a new washer jet in question.
No GO to H4
H4 CHECK FOR WASHER PUMP ACTIVATION
Ignition ON.
Momentarily activate the windshield washer function. While listening for washer pump activation near the right
front of the vehicle, have an assistant activate the windshield washer function.
Does the washer pump activate?
Yes GO to H5
No GO to H6
om
H5 CHECK FOR DAMAGED WASHER HOSES
.c
Inspect the washer hoses for kinks or damage.
Are the washer hoses OK?
er
ov
Yes INSTALL a new washer pump.
REFER to: Windshield Washer Pump (50116 Wipers and Washers, Removal and Installation).
No REPAIR the washer hoses as necessary.
ec
itr
H6 CHECK THE WIPER/WASHER SWITCH INPUT
.b
Ignition ON.
Using a diagnostic scan tool, view the SCCM Parameter Identifications (PIDs).
Using a diagnostic scan tool, view the SCCM F_WASH_SW PID.
w
Activate and release the wash function on the wiper/washer switch.
w
Does the PID indicate correctly when the switch is activated and released?
w
Yes GO to H7
No INSTALL a new wiper/washer switch.
REFER to: Steering Column Multifunction Switch RH (21105 Steering Wheel and Column
Electrical Components, Removal and Installation).
TEST the system for normal operation. If the concern is still present, INSTALL a new SCCM.
REFER to: Steering Column Control Module (SCCM) (21105 Steering Wheel and Column
Electrical Components, Removal and Installation).
H7 CHECK FOR VOLTAGE TO THE WASHER PUMP
NOTICE: The following Pinpoint Test uses a test lamp to simulate normal circuit loads. Use only a Rotunda
Test Lamp (SGT27000) or 250300mA incandescent bulb test lamp. To avoid connector terminal damage,
use the Rotunda Flex Probe kit for the test lamp probe connection to the vehicle. Do not use the test lamp
probe directly on any connector.
Ignition OFF.
Disconnect Washer Pump C134.
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 27/42
8/1/2016 2015 Edge
Disconnect Washer Pump C134.
Connect:
Click to display connectors
Positive Lead Measurement / Action Negative Lead
C1342 Ground
Ignition ON.
Use the wiper/washer switch to activate the washer pump.
Does the test lamp illuminate when the washer is activated?
Yes GO to H8
No GO to H9
H8 CHECK THE WASHER PUMP GROUND CIRCUIT FOR AN OPEN
om
NOTICE: The following Pinpoint Test uses a test lamp to simulate normal circuit loads. Use only a Rotunda
Test Lamp (SGT27000) or 250300mA incandescent bulb test lamp. To avoid connector terminal damage,
use the Rotunda Flex Probe kit for the test lamp probe connection to the vehicle. Do not use the test lamp
.c
probe directly on any connector.
Connect:
Click to display connectors er
ov
Positive Lead Measurement / Action Negative Lead
C1341 C1342
ec
itr
Ignition ON.
Use the wiper/washer switch to activate the washer pump.
.b
Does the test lamp illuminate when the washer is activated?
w
Yes INSTALL a new washer pump.
w
REFER to: Windshield Washer Pump (50116 Wipers and Washers, Removal and Installation).
No REPAIR the circuit.
w
H9 CHECK THE WASHER PUMP VOLTAGE SUPPLY CIRCUIT FOR A SHORT TO GROUND
NOTICE: The following Pinpoint Test uses a test lamp to simulate normal circuit loads. Use only a Rotunda
Test Lamp (SGT27000) or 250300mA incandescent bulb test lamp. To avoid connector terminal damage,
use the Rotunda Flex Probe kit for the test lamp probe connection to the vehicle. Do not use the test lamp
probe directly on any connector.
Ignition OFF.
Disconnect Windshield Wiper Motor C1655.
Connect:
Click to display connectors
Positive Lead Measurement / Action Negative Lead
C16558 Ground
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 28/42
8/1/2016 2015 Edge
Is the resistance greater than 10,000 ohms?
Yes GO to H10
No REPAIR the circuit.
H10 CHECK THE WASHER PUMP VOLTAGE SUPPLY CIRCUIT FOR AN OPEN
NOTICE: The following Pinpoint Test uses a test lamp to simulate normal circuit loads. Use only a Rotunda
Test Lamp (SGT27000) or 250300mA incandescent bulb test lamp. To avoid connector terminal damage,
use the Rotunda Flex Probe kit for the test lamp probe connection to the vehicle. Do not use the test lamp
probe directly on any connector.
Connect:
Click to display connectors
Positive Lead Measurement / Action Negative Lead
C16557 C1342
om
Is the resistance less than 3 ohms?
.c
Yes GO to H11
No REPAIR the circuit. er
ov
H11 CHECK FOR CORRECT WINDSHIELD WIPER MOTOR OPERATION
ec
Disconnect and inspect the windshield wiper motor connector.
Repair:
itr
corrosion (install new connector or terminal clean module pins)
damaged or bent pins install new terminals/pins
.b
pushedout pins install new pins as necessary
Reconnect the windshield wiper motor connector. Make sure it seats and latches correctly.
w
Operate the system and determine if the concern is still present.
w
Is the concern still present?
w
Yes CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this
concern, DISCONTINUE this test and FOLLOW the TSB instructions. If no Technical Service
Bulletins (TSBs) address this concern, INSTALL a new windshield wiper motor.
REFER to: Windshield Wiper Motor (50116 Wipers and Washers, Removal and Installation).
No The system is operating correctly at this time. The concern may have been caused by a loose or
corroded connector. ADDRESS the root cause of any connector or pin issues.
The Windshield Washer Is Always On
Refer to Wiring Diagrams Cell 81 for schematic and connector information.
Normal Operation and Fault Conditions
REFER to: Wipers and Washers System Operation and Component Description (50116 Wipers and Washers,
Description and Operation).
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 29/42
8/1/2016 2015 Edge
Possible Sources
Wiper/washer switch
Windshield wiper motor
SCCM
Visual Inspection and Diagnostic Prechecks
Inspect the wiper/washer switch for damage.
PINPOINT TEST I : THE WASHER PUMP IS ALWAYS ON
I1 CHECK THE WIPER/WASHER SWITCH INPUT
Ignition ON.
Using a diagnostic scan tool, view the SCCM Parameter Identifications (PIDs).
Using a diagnostic scan tool, view the SCCM F_WASH_SW PID.
Does the PID indicate correctly when the switch is activated and released?
Yes INSTALL a new wiper/washer switch.
om
REFER to: Steering Column Multifunction Switch RH (21105 Steering Wheel and Column
Electrical Components, Removal and Installation).
TEST the system for normal operation. If the concern is still present, INSTALL a new SCCM.
.c
REFER to: Steering Column Control Module (SCCM) (21105 Steering Wheel and Column
Electrical Components, Removal and Installation).
No INSTALL a new windshield wiper motor. er
ov
REFER to: Windshield Wiper Motor (50116 Wipers and Washers, Removal and Installation).
ec
One Or More Rear Window Wiper Modes Are Inoperative
itr
.b
Refer to Wiring Diagrams Cell 81 for schematic and connector information.
Normal Operation and Fault Conditions
w
w
REFER to: Wipers and Washers System Operation and Component Description (50116 Wipers and Washers,
w
Description and Operation).
Possible Causes
Fuse
Wiring, terminals or connectors
Washer pump
Wiper/washer switch
Rear window wiper motor
Windshield wiper motor
SCCM
Visual Inspection and Diagnostic Prechecks
Inspect BJB fuse 28 (10A) and make sure it is OK.
Inspect the wiper/washer switch for damage.
PINPOINT TEST J : ONE OR MORE REAR WINDOW WIPER MODES ARE INOPERATIVE
NOTICE: Use the correct probe adapter(s) when making measurements. Failure to use the correct probe
adapter(s) may damage the connector.
J1 CHECK THE WINDSHIELD WIPER OPERATION
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 30/42
8/1/2016 2015 Edge
J1 CHECK THE WINDSHIELD WIPER OPERATION
Ignition ON.
Place the wiper/washer switch to the windshield low speed position and then off.
Does the windshield wiper operate?
Yes GO to J2
No GO to Pinpoint Test A
J2 CHECK THE REAR WINDOW WIPER/WASHER SWITCH INPUT PARAMETER IDENTIFICATIONS
(PIDS)
Ignition ON.
Using a diagnostic scan tool, view the SCCM Parameter Identifications (PIDs).
Using a diagnostic scan tool, view the following SCCM Parameter Identifications (PIDs).
Rear Wiper Off Switch (R_WIPE_OFF_SW)
Rear Wiper Delay 1 (R_WIPE_DEL1)
Rear Wiper Delay 2 (R_WIPE_DEL2)
om
Place the wiper/washer switch to the rear INT 1 and rear INT 2 positions, and then off.
Do the Parameter Identifications (PIDs) indicate correctly for the switch positions?
.c
Yes VERIFY the BJB fuse 29 (15A) is OK. If OK, GO to J3
If not OK, REFER to the Wiring Diagrams manual to identify the possible cause of the circuit
short.
No INSTALL a new wiper/washer switch.
er
ov
REFER to: Steering Column Multifunction Switch RH (21105 Steering Wheel and Column
Electrical Components, Removal and Installation).
ec
TEST the system for normal operation. If the concern is still present, INSTALL a new SCCM.
REFER to: Steering Column Control Module (SCCM) (21105 Steering Wheel and Column
itr
Electrical Components, Removal and Installation).
.b
J3 CHECK THE REAR WINDOW WIPER MOTOR VOLTAGE SUPPLY CIRCUIT FOR AN OPEN
w
Ignition OFF.
w
Disconnect Rear Window Wiper Motor C476.
Ignition ON.
w
Measure:
Click to display connectors
Positive Lead Measurement / Action Negative Lead
C4761 Ground
Is the voltage greater than 11 volts?
Yes GO to J4
No REPAIR the circuit.
J4 CHECK THE REAR WINDOW WIPER MOTOR GROUND CIRCUIT FOR AN OPEN
Ignition OFF.
Measure:
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 31/42
8/1/2016 2015 Edge
Click to display connectors
Positive Lead Measurement / Action Negative Lead
C4763 Ground
Is the resistance less than 3 ohms?
Yes GO to J5
No REPAIR the circuit.
J5 CHECK THE REAR WINDOW WIPER MOTOR CONTROL CIRCUIT FOR A SHORT TO VOLTAGE
Disconnect Windshield Wiper Motor C1655.
Ignition ON.
Measure:
om
Click to display connectors
Positive Lead Measurement / Action Negative Lead
.c
C4762 Ground
er
ov
Is any voltage present?
ec
Yes REPAIR the circuit.
No GO to J6
itr
.b
J6 CHECK THE REAR WINDOW WIPER MOTOR CONTROL CIRCUIT FOR AN OPEN
w
Ignition OFF.
Measure:
w
Click to display connectors
w
Is the resistance less than 3 ohms?
Yes GO to J7
No REPAIR the circuit.
J7 BYPASS THE WINDSHIELD WIPER MOTOR
Connect Rear Window Wiper Motor C476.
Connect:
Click to display connectors
Positive Lead Measurement / Action Negative Lead
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 32/42
8/1/2016 2015 Edge
C165511 C16556
Ignition ON.
Does the rear window wiper motor operate?
Yes REMOVE the fused jumper wire. GO to J8
No REMOVE the fused jumper wire. INSTALL a new rear window wiper motor.
REFER to: Rear Window Wiper Motor (50116 Wipers and Washers, Removal and Installation).
J8 CHECK FOR CORRECT WINDSHIELD WIPER MOTOR OPERATION
Disconnect and inspect the windshield wiper motor connector.
Repair:
corrosion (install new connector or terminal clean module pins)
damaged or bent pins install new terminals/pins
om
pushedout pins install new pins as necessary
Reconnect the windshield wiper motor connector. Make sure it seats and latches correctly.
Operate the system and determine if the concern is still present.
.c
Is the concern still present?
er
Yes CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this
concern, DISCONTINUE this test and FOLLOW the TSB instructions. If no Technical Service
ov
Bulletins (TSBs) address this concern, INSTALL a new windshield wiper motor.
REFER to: Windshield Wiper Motor (50116 Wipers and Washers, Removal and Installation).
ec
No The system is operating correctly at this time. The concern may have been caused by a loose or
corroded connector. ADDRESS the root cause of any connector or pin issues.
itr
.b
w
The Rear Window Wiper Stays On Continuously
w
Refer to Wiring Diagrams Cell 81 for schematic and connector information.
w
Normal Operation and Fault Conditions
REFER to: Wipers and Washers System Operation and Component Description (50116 Wipers and Washers,
Description and Operation).
Possible Causes
Wiring, terminals or connectors
Wiper/washer switch
Rear window wiper motor
Windshield wiper motor
SCCM
Visual Inspection and Diagnostic Prechecks
Inspect the wiper/washer switch for damage.
PINPOINT TEST K : THE REAR WINDOW WIPER STAYS ON CONTINUOUSLY
NOTICE: Use the correct probe adapter(s) when making measurements. Failure to use the correct probe
adapter(s) may damage the connector.
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 33/42
8/1/2016 2015 Edge
adapter(s) may damage the connector.
K1 CHECK THE REAR WINDOW WIPER/WASHER SWITCH INPUT PARAMETER IDENTIFICATIONS
(PIDS)
Ignition ON.
Using a diagnostic scan tool, view the SCCM Parameter Identifications (PIDs).
Using a diagnostic scan tool, view the following SCCM Parameter Identifications (PIDs).
Rear Wiper Off Switch (R_WIPE_OFF_SW)
Rear Wiper Delay 1 (R_WIPE_DEL1)
Rear Wiper Delay 2 (R_WIPE_DEL2)
Place the wiper/washer switch to the rear INT 1 and rear INT 2 positions, and then off.
Do the Parameter Identifications (PIDs) indicate correctly for the switch positions?
Yes GO to K2
No INSTALL a new wiper/washer switch.
REFER to: Steering Column Multifunction Switch RH (21105 Steering Wheel and Column
Electrical Components, Removal and Installation).
TEST the system for normal operation. If the concern is still present, INSTALL a new SCCM.
om
REFER to: Steering Column Control Module (SCCM) (21105 Steering Wheel and Column
Electrical Components, Removal and Installation).
.c
K2 CHECK THE WINDSHIELD WIPER MOTOR
Ignition OFF.
Disconnect Windshield Wiper Motor C1655. er
ov
Ignition ON.
Does the rear window wiper motor continue to operate?
ec
Yes GO to K3
itr
No GO to K4
.b
w
K3 CHECK THE WINDSHIELD REAR WIPER CONTROL CIRCUIT FOR A SHORT TO GROUND
Ignition OFF.
w
Disconnect Rear Window Wiper Motor C476.
w
Measure:
Click to display connectors
Positive Lead Measurement / Action Negative Lead
C4762 Ground
Is the resistance greater than 10,000 ohms?
Yes INSTALL a new rear window wiper motor.
REFER to: Rear Window Wiper Motor (50116 Wipers and Washers, Removal and Installation).
No REPAIR the circuit.
K4 CHECK FOR CORRECT WINDSHIELD WIPER MOTOR OPERATION
Disconnect and inspect the windshield wiper motor connector.
Repair:
corrosion (install new connector or terminal clean module pins)
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 34/42
8/1/2016 2015 Edge
corrosion (install new connector or terminal clean module pins)
damaged or bent pins install new terminals/pins
pushedout pins install new pins as necessary
Reconnect the windshield wiper motor connector. Make sure it seats and latches correctly.
Operate the system and determine if the concern is still present.
Is the concern still present?
Yes CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this
concern, DISCONTINUE this test and FOLLOW the TSB instructions. If no Technical Service
Bulletins (TSBs) address this concern, INSTALL a new windshield wiper motor.
REFER to: Windshield Wiper Motor (50116 Wipers and Washers, Removal and Installation).
No The system is operating correctly at this time. The concern may have been caused by a loose or
corroded connector. ADDRESS the root cause of any connector or pin issues.
The Rear Window Washer Is Inoperative
om
Refer to Wiring Diagrams Cell 81 for schematic and connector information.
.c
Normal Operation and Fault Conditions
er
REFER to: Wipers and Washers System Operation and Component Description (50116 Wipers and Washers,
Description and Operation).
ov
Possible Causes
ec
Fuse
Rear washer hose
Rear washer jet
itr
Wiring, terminals or connectors
Washer pump relay
.b
Washer pump
Wiper/washer switch
w
Windshield wiper motor
SCCM
w
Visual Inspection and Diagnostic Prechecks
w
Inspect BJB fuse 28 (10A) and make sure it is OK.
Inspect the wiper/washer switch for damage.
PINPOINT TEST L : THE REAR WINDOW WASHER IS INOPERATIVE
NOTICE: Use the correct probe adapter(s) when making measurements. Failure to use the correct probe
adapter(s) may damage the connector.
L1 CHECK THE WINDSHIELD WASHER OPERATION
Ignition ON.
Activate the windshield washer and observe the windshield washer operation.
Does the windshield washer operate correctly?
Yes GO to L2
No GO to Pinpoint Test H
L2 CHECK THE AMBIENT AIR TEMPERATURE
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 35/42
8/1/2016 2015 Edge
L2 CHECK THE AMBIENT AIR TEMPERATURE
Check the ambient air temperature.
Is the ambient air temperature below freezing?
Yes GO to L3
No GO to L4
L3 CHECK THE WASHER SOLVENT
Check the washer solvent and make sure it is of the correct type to use for the temperature conditions present.
Is the correct type of washer solvent present?
Yes GO to L4
No ALLOW the vehicle to warm to room temperature. DRAIN and REFILL the windshield washer
reservoir with the correct washer solvent type. INFORM the customer of the correct type of
om
washer solvent to use for the temperature conditions present.
.c
L4 CHECK FOR WASHER SOLVENT TO THE WASHER JET
Disconnect the washer hose from the rear window washer jet and place it in a container to capture fluid.
Momentarily activate the rear window washer.
er
ov
Is washer fluid emitted at the washer hose?
Yes INSTALL a new washer jet.
ec
No GO to L5
itr
.b
L5 CHECK FOR WASHER MOTOR ACTIVATION
Ignition ON.
w
While listening for washer motor activation near the right front of the vehicle, have an assistant activate the rear
window washer.
w
Does the washer motor activate?
w
Yes GO to L6
No GO to L7
L6 CHECK FOR DAMAGED WASHER HOSES
Inspect the washer hoses for kinks or damage.
Are the washer hoses OK?
Yes Install a new washer pump.
REFER to: Windshield Washer Pump (50116 Wipers and Washers, Removal and Installation).
No REPAIR the washer hoses as necessary.
L7 CHECK THE WIPER/WASHER SWITCH INPUT USING THE REAR WIPER WASH SWITCH
(R_WIPE_WASH_SW) PID (PARAMETER IDENTIFICATION)
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 36/42
8/1/2016 2015 Edge
(R_WIPE_WASH_SW) PID (PARAMETER IDENTIFICATION)
Ignition ON.
Using a diagnostic scan tool, view the SCCM Parameter Identifications (PIDs).
Using a diagnostic scan tool, view the SCCM R_WIPE_WASH_SW PID.
Activate and release the rear window wash function on the wiper/washer switch.
Does the PID indicate correctly when the switch is activated and released?
Yes GO to L8
No INSTALL a new wiper/washer switch.
REFER to: Steering Column Multifunction Switch RH (21105 Steering Wheel and Column
Electrical Components, Removal and Installation).
TEST the system for normal operation. If the concern is still present, INSTALL a new SCCM.
REFER to: Steering Column Control Module (SCCM) (21105 Steering Wheel and Column
Electrical Components, Removal and Installation).
om
L8 CHECK THE WASHER PUMP RELAY COIL CIRCUIT
NOTICE: The following Pinpoint Test uses a test lamp to simulate normal circuit loads. Use only a Rotunda
Test Lamp (SGT27000) or 250300mA incandescent bulb test lamp. To avoid connector terminal damage,
.c
use the Rotunda Flex Probe kit for the test lamp probe connection to the vehicle. Do not use the test lamp
probe directly on any connector.
Ignition OFF.
Disconnect Windshield Washer Pump C134. er
ov
Connect:
Click to display connectors
ec
Ignition ON.
Have an assistant activate the rear window wash function
w
Does the test lamp illuminate when the rear window wash function is activated?
w
Yes GO to L12
w
No GO to L9
L9 CHECK THE WASHER PUMP RELAY COIL VOLTAGE SUPPLY CIRCUIT FOR AN OPEN
Ignition OFF.
Disconnect BJB C1035B.
Measure:
Click to display connectors
Positive Lead Measurement / Action Negative Lead
C1035B28 C1035B12
Is the resistance less than 3 ohms?
Yes GO to L10
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 37/42
8/1/2016 2015 Edge
Yes GO to L10
No REPAIR the circuit.
L10 CHECK THE WASHER PUMP RELAY COIL CONTROL CIRCUIT FOR A SHORT TO VOLTAGE
Ignition ON.
Measure:
Click to display connectors
Positive Lead Measurement / Action Negative Lead
C1035B32 Ground
Is any voltage present?
Yes REPAIR the circuit.
om
No GO to L11
.c
L11 CHECK THE WASHER PUMP RELAY COIL CONTROL CIRCUIT FOR AN OPEN
er
NOTICE: The following Pinpoint Test uses a test lamp to simulate normal circuit loads. Use only a Rotunda
Test Lamp (SGT27000) or 250300mA incandescent bulb test lamp. To avoid connector terminal damage,
ov
use the Rotunda Flex Probe kit for the test lamp probe connection to the vehicle. Do not use the test lamp
probe directly on any connector.
Disconnect BJB C1035A.
ec
Connect a fused jumper wire:
Click to display connectors
itr
C1035A12 CBATTERY POSITIVE
w
Connect:
w
Click to display connectors
w
Ignition ON.
Have an assistant activate the rear window wash function
Does the test lamp illuminate when the rear window wash function is activated?
Yes INSTALL a new BJB.
No GO to L12
L12 CHECK FOR CORRECT WINDSHIELD WIPER MOTOR OPERATION
Disconnect and inspect the windshield wiper motor connector.
Repair:
corrosion (install new connector or terminal clean module pins)
damaged or bent pins install new terminals/pins
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 38/42
8/1/2016 2015 Edge
damaged or bent pins install new terminals/pins
pushedout pins install new pins as necessary
Reconnect the windshield wiper motor connector. Make sure it seats and latches correctly.
Operate the system and determine if the concern is still present.
Is the concern still present?
Yes CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this
concern, DISCONTINUE this test and FOLLOW the TSB instructions. If no Technical Service
Bulletins (TSBs) address this concern, INSTALL a new windshield wiper motor.
REFER to: Windshield Wiper Motor (50116 Wipers and Washers, Removal and Installation).
No The system is operating correctly at this time. The concern may have been caused by a loose or
corroded connector. ADDRESS the root cause of any connector or pin issues.
The Rear Window Washer Is Always On
om
Refer to Wiring Diagrams Cell 81 for schematic and connector information.
Normal Operation and Fault Conditions
.c
er
REFER to: Wipers and Washers System Operation and Component Description (50116 Wipers and Washers,
Description and Operation).
ov
Possible Causes
Wiring, terminals or connectors
ec
Washer pump relay
Wiper/washer switch
Windshield wiper motor
itr
SCCM
.b
Visual Inspection and Diagnostic Prechecks
Inspect the wiper/washer switch for damage.
w
w
PINPOINT TEST M : THE REAR WINDOW WASHER IS ALWAYS ON
w
NOTICE: Use the correct probe adapter(s) when making measurements. Failure to use the correct probe
adapter(s) may damage the connector.
M1 CHECK THE WIPER/WASHER SWITCH INPUT USING THE REAR WIPER WASH SWITCH
(R_WIPE_WASH_SW) PID (PARAMETER IDENTIFICATION)
Ignition ON.
Using a diagnostic scan tool, view the SCCM Parameter Identifications (PIDs).
Using a diagnostic scan tool, view the SCCM R_WIPE_WASH_SW PID.
Activate and release the rear window wash function on the wiper/washer switch.
Does the PID indicate correctly when the switch is activated and released?
Yes GO to M2
No INSTALL a new wiper/washer switch.
REFER to: Steering Column Multifunction Switch RH (21105 Steering Wheel and Column
Electrical Components, Removal and Installation).
TEST the system for normal operation. If the concern is still present, INSTALL a new SCCM.
REFER to: Steering Column Control Module (SCCM) (21105 Steering Wheel and Column
Electrical Components, Removal and Installation).
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 39/42
8/1/2016 2015 Edge
M2 CHECK THE WASHER PUMP RELAY COIL CONTROL CIRCUIT FOR A SHORT TO GROUND
Ignition OFF.
Disconnect Windshield Wiper Motor C1655.
Measure:
Click to display connectors
Positive Lead Measurement / Action Negative Lead
C165512 Ground
Is the resistance greater than 10,000 ohms?
Yes GO to M5
No GO to M3
om
.c
M3 ISOLATE THE WASHER PUMP RELAY COIL CONTROL CIRCUIT SHORT TO GROUND
Ignition OFF.
Disconnect Disconnect BJB C1035B.
Measure:
er
ov
Click to display connectors
ec
Is the resistance greater than 10,000 ohms?
w
Yes GO to M4
w
No REPAIR the circuit.
w
M4 CHECK THE WASHER PUMP RELAY OUTPUT CIRCUIT FOR A SHORT TO VOLTAGE
Disconnect Windshield Washer Pump C137.
Measure:
Click to display connectors
Positive Lead Measurement / Action Negative Lead
C1371 Ground
Is any voltage present?
Yes GO to M5
No GO to M6
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 40/42
8/1/2016 2015 Edge
M5 CHECK THE WASHER PUMP RELAY OUTPUT CIRCUIT FOR A SHORT TO VOLTAGE IN THE BJB
Ignition OFF.
Disconnect BJB C1035B.
Ignition ON.
Measure:
Click to display connectors
Positive Lead Measurement / Action Negative Lead
C1341 Ground
Is any voltage present?
Yes REPAIR the circuit.
No REFER to the wiring diagrams manual to identify the cause of the short to power in the BJB.
om
M6 CHECK FOR CORRECT WINDSHIELD WIPER MOTOR OPERATION
Disconnect and inspect the windshield wiper motor connector.
.c
Repair:
corrosion (install new connector or terminal clean module pins)
damaged or bent pins install new terminals/pins
pushedout pins install new pins as necessary er
ov
Reconnect the windshield wiper motor connector. Make sure it seats and latches correctly.
Operate the system and determine if the concern is still present.
ec
Is the concern still present?
itr
Yes CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this
concern, DISCONTINUE this test and FOLLOW the TSB instructions. If no Technical Service
Bulletins (TSBs) address this concern, INSTALL a new windshield wiper motor.
.b
No The system is operating correctly at this time. The concern may have been caused by a loose or
w
corroded connector. ADDRESS the root cause of any connector or pin issues.
w
w
The Front Camera Washer Is Inoperative
Normal Operation and Fault Conditions
REFER to: Wipers and Washers System Operation and Component Description (50116 Wipers and Washers,
Description and Operation).
Possible Causes
Front camera washer hose
Front camera washer jet
Visual Inspection and Diagnostic Prechecks
Inspect the front camera washer jet for damage
PINPOINT TEST N : THE FRONT CAMERA WASHER IS INOPERATIVE
N1 CHECK THE WINDSHIELD WASHER OPERATION
Ignition ON.
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 41/42
8/1/2016 2015 Edge
Ignition ON.
Momentarily activate the windshield washer function.
Does the windshield washer operate?
Yes GO to N2
No GO to Pinpoint Test H
N2 CHECK FOR WASHER SOLVENT TO THE FRONT CAMERA WASHER JET
Ignition OFF.
Disconnect the washer hose from the front camera washer jet and place it in a container to capture fluid.
Ignition ON.
Momentarily activate the windshield washer function.
Is washer fluid emitted at the washer hose?
Yes INSTALL a new front camera washer jet.
om
No INSTALL a new front camera washer hose.
.c
er
ov
ec
itr
.b
w
w
w
http://www.fordtechservice.dealerconnection.com/vdirs/protech/global/default.asp?comefrom=Motocraft 42/42