Professional Documents
Culture Documents
kr
PROPRIETARY NOTE
THIS SPECIFICATION IS THE PROPERTY OF BOE OT AND SHALL NOT BE
REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF BOE OT
AND MUST BE RETURNED TO BOE OT UPON ITS REQUEST
TITLE : HT141WXB-100
Preliminary Product Specification
Rev. P0
REVISION HISTORY
REV. ECN NO. DESCRIPTION OF CHANGES DATE PREPARED
P0 - Initial Release 2008.04.18. W. Kim
Contents
13.0 Label 23
1.1 Introduction
HT141WXB-100 is a color active matrix TFT LCD module using amorphous silicon TFT's
(Thin Film Transistors) as an active switching devices. This module has a 14.1 inch
diagonally measured active area with WXGA resolutions (1280 horizontal by 800 vertical
pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in
vertical Stripe and this module can display 262,144 colors. The TFT-LCD panel used for this
module is a low reflection and higher color type. Therefore, this module is suitable for
Notebook PC. The DC/AC inverter for back-light driving is not built in this model.
Source Driver
LVDS
Input
Signal LVDS Rx
Connector (CN 1 )
+
Gate Driver
T/CON
TFT LCD Panel
BACK LIGHT (Fluorescent Lamp)
VDD
DC/DC 1280 Ч800
Gamma
Vcom
SPWG (Standard Panel Working Group) 14.1”W type WXGA(16:10) Form Factor
Thin and light weight
3.3 V power supply
1 Channel LVDS Interface
Single CCFL (Bottom side/Horizontal Direction)
262,144 colors
Data enable signal mode
Side Mounting Frame
Green Product (RoHS product)
On board EDID chip
Low driving voltage and low power consumption
1.3 Application
The followings are general specifications at the model HT141WXB-100. (listed in Table 1.)
PBL: 4.1 W
Ptotal : 5.2 W
The followings are maximum values which, if exceed, may cause faulty operation or
damage to the unit. The operational and non-operational maximum voltage and current
values are listed in Table 2.
90 (40, 90)
80
60
Operating Range (50, 50)
40
(60, 27)
20
Storage Range
5
-40 -20 0 20 40 60 80
Temperature (℃)
At Ta = 25℃
- 680 Vrms Note 4
Lamp Start Voltage
At Ta = 0℃
- - Vrms
Note 4
Notes : 1. The supply voltage is measured and specified at the interface connector of LCM.
The current draw and power consumption specified is for 3.3V at 25℃.
a) Typ : Window XP pattern
b) Max : Vertical 2 line skip pattern
3. The lamp frequency should be selected as different as possible from the horizontal
synchronous frequency and its harmonics to avoid interference which may
cause line flow on the display.
4. For starting the backlight unit, the output voltage of DC/AC's transformer should
be larger than the minimum lamp starting voltage.
(1,240 Vrms at 25 ℃ & 1,490 Vrms at 0 ℃)
If an inverter has shutdown function it should keep its output for more than
1 second even if the lamp connector open. Otherwise the lamps may not to be
turned on.
5. End of Life shall be determined by the time when any of the following is satisfied
under continuous lighting at 25℃ and IBL = 6.0[mA] Max Only.
Intensity drops to 50% of the Initial Value.
4.1 Overview
The test of Optical specifications shall be measured in a dark room (ambient luminance ≤ 1
lux and temperature = 25±2℃) with the equipment of Luminance meter system (Goniometer
system and TOPCONE BM-5) and test unit shall be located at an approximate distance
50cm from the LCD surface at a viewing angle of θ and Φ equal to 0°. We refer to θШ=0
(=θ3 ) as the 3 o’clock direction (the “right”), θШ=90 (= θ12 ) as the 12 o’clock direction
(“upward”), θШ=180 (= θ9 ) as the 9 o’clock direction (“left”) and
θШ=270(= θ6 ) as the 6 o’clock direction (“bottom”). While scanning θand/or Ш, the center
of the measuring spot on the Display surface shall stay fixed. The backlight should be
operating for 30 minutes prior to measurement... VDD shall be 3.3+/- 0.3V at 25°C.
Optimum viewing angle direction is 6 ’clock.
Θ3 45 45 - Deg.
Horizontal
Θ9 45 45 - Deg.
Viewing Angle CR > 10 Note 1
range 15 25 - Deg.
Θ12
Vertical
Θ6 40 40 - Deg.
xR TBD
Red
yR TBD
xG TBD
Reproduction Θ = 0°
Green
of color yG TBD
Blue xB TBD
yB TBD
Notes : 1. Viewing angle is the angle at which the contrast ratio is greater than 10. The
viewing angles are determined for the horizontal or 3, 9 o’clock direction and the
vertical or 6, 12 o’clock direction with respect to the optical axis which is normal
to the LCD surface (see FIGURE 1).
Photo detector
( TOPCON BM-5A)
Field = 2o
50 cm
TFT-LCD module LCD panel
400
600
10mm 10mm
320 640 960
10mm
192
384
576
10mm
TR TF
Optical 100%
90%
Response
10%
0%
Time
320,200 960,200
YA(1120, 400) L0
Where:
YA= Initial luminance of measured area (cd/m2)
YB= Subsequent luminance of measured area (cd/m2)
The location measured will be exactly the same in both patterns
LV DS to TT L Parallel
R0~R5
6 100 ohm 6
G0~G5
G0~G5
6 100 ohm 6
B0~B5
B0~B5
Hsync Hsync
100 ohm
Vsync Vsync
DE DE
CLK+ Vdiff=0V
Rin0 GO R5 R4 R3 R2 R1 R0
Rin1 B1 B0 G5 G4 G3 G2 G1
5.4.Back-light Interface
T1
T2
DE
T3
DCLK
T5
T4
DE
tRIP6
tRIP5
tRIP4
tRIP3
tRIP2
tRIP1
tRIP0
RxINz +/- Rx3 Rx2 Rx1 Rx0 Rx6 Rx5 Rx4 Rx3 Rx2 Rx1 Rx0
* Z = 0, 1, 2
<Table 10. Input signals, Basic display colors and Gray scale for each color.>
Colors & Data signal
Gray scale R0 R1 R2 R3 R4 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3 B4 B5
R5
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Blue 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1
Basic Green 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0
colors Light Blue 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1
Red 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0
Purple 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1
Yel ow 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0
White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
△ 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Gray Darker 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
scale △ ↓ ↓ ↓
of ▽ ↓ ↓ ↓
Red Brighter 1 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0
▽ 0 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0
Red 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
△ 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0
Gray Darker 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0
scale △ ↓ ↓ ↓
of ▽ ↓ ↓ ↓
Green Brighter 0 0 0 0 0 0 1 0 1 1 1 1 0 0 0 0 0 0
▽ 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0
Green 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
△ 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
Gray Darker 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0
scale △ ↓ ↓ ↓
of ▽ ↓ ↓ ↓
Blue Brighter 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1 1
▽ 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1
Blue 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Gray △ 1 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0 0 0
scale Darker 0 1 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0 0
of △ ↓ ↓ ↓
White ▽ ↓ ↓ ↓
& Brighter 1 0 1 1 1 1 1 0 1 1 1 1 1 0 1 1 1 1
Black ▽ 0 1 1 1 1 1 0 1 1 1 1 1 0 1 1 1 1 1
White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
To prevent a latch-up or DC operation of the LCD module, the power on/off sequence shall
be as shown in below
0.9VDD 0.9VDD
Power Supply 0.1VDD 0.1VDD
0V
T1
T5 T7
T2
T6
Valid
Interface Signal
0V
T3 T4
Back- light 0V
● T1 ≤ 10 ms
● 0 ≤ T2 ≤ 50 ms
● 200 ms ≤ T3
● 200 ms ≤ T4
● 0 ≤ T5 ≤ 50 ms
● 0 ≤ T6 ≤ 10ms
● 200ms ≤ T7
Notes : 1. When the power supply VDD is 0V, Keep the level of input signals on the low or keep
high impedance.
2. Do not keep the interface signal high impedance when power is on.
Back Light must be turn on after power for logic and interface signal are valid.
10.2 Mounting
See FIGURE 6.
The surface of the LCD has an glare coating to maximize readability and hard coating
to reduce scratching.
There shall not be visible light from the back-lighting system around the edges of the
screen as seen from a distance 50cm from the screen with an overhead light level of 350lux.
13.0 LABEL
(1) Product label
1 2 3 4 5 6 7
X X X X X X 1 00 XX X X X X XX
HT141WXB-100 12
0000000000000 200X.X.XX
00 0 0 00 0 0000 000000
Type Grade Line Year Month FG-Code Serial No
14.2 Notes
Address
Function Hex Dec values. Notes
(HEX)
00 00 0 0
01 FF 255 255
02 FF 255 255
03 FF 255 255
Header EDID Header
04 FF 255 255
05 FF 255 255
06 FF 255 255
07 00 0 0
08 09 9
ID Manufacturer Name BOE ID = BOE
09 E5 229
0A 81 129
ID Product Code 1409 ID = 0581 WXGA
0B 05 5
0C 00 0
0D 00 0
32-bit serial No.
0E 00 0
0F 00 0
10 Week of manufacture 00 0 0
11 Year of Manufacture 12 18 2008 Manufactured in 2008
12 EDID Structure Ver. 01 1 1 EDID Ver 1.0
13 EDID revision # 01 1 1 EDID Rev. 0.1
14 Video input definition 80 50 -
15 Max H image size 1E 30 30 30 cm (Approx)
16 Max V image size 13 19 19 19 cm (Approx)
17 Display Gamma 78 120 2.2 Gamma curve = 2.2
RGB display, Preferred Timming
18 Feature support 0A 10
mode
19 Red/Green low bits 62 98 - Red / Green Low Bits
1A Blue/White low bits 05 5 - Blue / White Low Bits
1B Red x high bits 95 149 0.583 Red (x) = 10010101 (0.58348)
1C Red y high bits 56 86 0.338 Red (y) = 01010110 (0.33836)
1D Green x high bits 4E 78 0.305 Green (x) = 01001110 (0.30482)
1E Green y high bits 8E 142 0.557 Green (y) = 10001110 (0.55656)
1F Blue x high bits 26 38 0.148 Blue (x) = 00100110 (0.14812)
20 BLue y high bits 24 36 0.141 Blue (y) = 00100100 (0.14068)
21 White x high bits 50 80 0.313 White (x) = 01010000 (0.313)
22 White y high bits 54 84 0.329 White (y) = 01010100 (0.329)
Address
Function Hex Dec values. Notes
(HEX)
23 Established timing 1 00 0 -
24 Established timing 2 00 0 -
25 Established timing 3 00 0 -
26 01 1
Standard timing #1 Not Used
27 01 1
28 01 1
Standard timing #2 Not Used
29 01 1
2A 01 1
Standard timing #3 Not Used
2B 01 1
2C 01 1
Standard timing #4 Not Used
2D 01 1
2E 01 1
Standard timing #5 Not Used
2F 01 1
30 01 1
Standard timing #6 Not Used
31 01 1
32 01 1
Standard timing #7 Not Used
33 01 1
34 01 1
Standard timing #8 Not Used
35 01 1
36 C7 199
71.11 71.11MHz Main clock
37 1B 27
38 00 0 1280 Hor Active = 1280
39 A0 160 160 Hor Blanking = 160
3A 80 4 bits of Hor. Active + 4 bits of Hor.
50 -
Blanking
3B 20 32 800 Ver Active = 800
3C 17 23 23 Ver Blanking = 23
48 4 bits of Ver. Active + 4 bits of Ver.
3D 30 -
Blanking
3E Detailed timing/monitor 30 48 48 Hor Sync Offset = 48
3F descriptor #1 20 32 32 H Sync Pulse Width = 32
40 (60Hz) 36 54 3 V sync Offset = 3 line
41 00 0 6 V Sync Pulse width : 6 line
42 2F 47 Horizontal Image Size = 303 mm
303
(Low 8 bits)
Vertical Image Size = 190 mm
43 BE 190 190
(Low 8 bits)
4 bits of Hor Image Size + 4 bits of
44 10 16 -
Ver Image Size
45 00 0 0 Hor Border (pixels)
46 00 0 0 Vertical Border (Lines)
47 19 25 -
Address
Function Hex Dec values. Notes
(HEX)
48 00 0
49 00 0
4A 00 0
4B FE 0
4C 00 0
4D 0A 0
4E 20 0
4F 20 0
50 Detailed timing/monitor 20 0
51 descriptor #2 20 0
52 20 0
53 20 0
54 20 0
55 20 0
56 20 0
57 20 0
58 20 0
59 20 0
5A 00 0
5B 00 0
5C 00 0 ASCII Data String Tag
5D FE 0
5E 00 0
5F 42 66 B
60 4F 79 O
61 45 69 E
62 Detailed timing/monitor 20 32
63 descriptor #3 4F 79 O Manufacturer name : BOE OT
64 54 84 T
65 0A 10
66 20 32
67 20 32
68 20 32
69 20 32
6A 20 32
6B 20 32