Professional Documents
Culture Documents
TASK A350-A-24-71-57-00001-921A-A
ON A/C ALL
References
Table 1 References
ON A/C ALL
ON A/C ALL
MP - Energize the Aircraft Electrical Circuits from External Power
A350-A-24-41-XX-00ZZZ-761Z-A
Receptacle 1
ON A/C ALL
ON A/C ALL
MP - Removal of the ATA27 Remote Control Circuit Breaker (RCCB)
A350-A-24-71-57-02ZZZ-520Z-A
from Electrical Power Distribution Center 1 (EPDC1)
ON A/C ALL
ON A/C ALL
MP - Removal of the ATA30 Remote Control Circuit Breaker (RCCB)
A350-A-24-71-57-05ZZZ-520Z-A
from Electrical Power Distribution Center 1 (EPDC1)
ON A/C ALL
MP - Removal of the ATA38 Remote Control Circuit Breaker (RCCB)
A350-A-24-71-57-06ZZZ-520Z-A
from Electrical Power Distribution Center 1 (EPDC1)
ON A/C ALL
ON A/C ALL
MP - Removal of the ATA24 Remote Control Circuit Breaker (RCCB)
A350-A-24-71-57-09ZZZ-520Z-A
from Electrical Power Distribution Center 2 (EPDC2)
ON A/C ALL
MP - Removal of the ATA21 Remote Control Circuit Breaker (RCCB)
A350-A-24-71-57-0AZZZ-520Z-A
from Electrical Power Distribution Center 2 (EPDC2)
ON A/C ALL
ON A/C ALL
ON A/C ALL and (FOR FIN 1001-QA or RCCB-PUMP STBY 1 SPLY or FOR FIN 2001-QA or RCCB-PUMP MAIN 2 SPLY)
MP - Installation of the ATA28 Remote Control Circuit Breaker
A350-A-24-71-57-03ZZZ-720Z-A
(RCCB) in Electrical Power Distribution Center 1 (EPDC1)
ON A/C ALL
ON A/C ALL
ON A/C ALL
MP - Installation of the ATA21 Remote Control Circuit Breaker
A350-A-24-71-57-0AZZZ-720Z-A
(RCCB) in Electrical Power Distribution Center 2 (EPDC2)
ON A/C ALL and (FOR FIN 2008-CV or RCCB-ADGB MCE EMOT PWR)
MP - Installation of the ATA27 Remote Control Circuit Breaker
A350-A-24-71-57-0BZZZ-720Z-A
(RCCB) in Electrical Power Distribution Center 2 (EPDC2)
ON A/C ALL and (FOR FIN 1000-QA or RCCB-PUMP STBY 2 SPLY or FOR FIN 2000-QA or RCCB-PUMP MAIN 1 SPLY)
MP - Installation of the ATA28 Remote Control Circuit Breaker
A350-A-24-71-57-0CZZZ-720Z-A
(RCCB) in Electrical Power Distribution Center 2 (EPDC2)
ON A/C ALL
ON A/C ALL
1. General
B. Additional information
This procedure gives the instructions necessary to swap (interchange) the RCCB when RCCB is defective.
NOGO RCCB: RCCB LRM with at least one RCCB failed leading to a NO_DISPATCH condition according to MEL.
GO or GOIF RCCB: RCCB LRM which allows the dispatch even in case of failure (with or without condition described in MEL).
A. Required Conditions
None
B. Support Equipment
ON A/C ALL
None
D. Spares
Table 5 Spares
None
E. Safety Conditions
None
3. Job Set-Up
ON A/C ALL
SUBTASK 247157-10102630001
4. Procedure
ON A/C ALL
SUBTASK 247157-40100660001
Ref. MP A350-A-24-41-XX-00ZZZ-561Z-A.
ON A/C ALL
SUBTASK 247157-40100750001
ON A/C ALL
SUBTASK 247157-40100670001
NOTE: It is possible that RCCBs of the same P/N root are not interchangeable. It is necessary to refer to the applicable IPD task to
(2) Remove the RCCB which will be used to solve NO GO Configuration on RCCB:
NOTE: P1 is related to the first RCCB that must be used for the replacement.
Table 7
9 AC (1091MC)
10 AC (1102MC)
Table 8
9 AC (1091MC)
(3) Install the defective RCCB on position of the replacement RCCB (P1, P2 or P3):
(b) Install defective RCCB on position of green electrical-pump RCCB (1001JV) Ref. MP A350-A-24-71-57-04ZZZ-720Z-A.
NOTE: It is not necessary to do the test requested in the installation procedure.
(c) Install defective RCCB on position of AC galley-feeder 10 RCCB (1102MC) Ref. MP A350-A-24-71-57-09ZZZ-720Z-A.
NOTE: It is not necessary to do the test requested in the installation procedure.
(4) Put a WARNING NOTICE(S) in position on defective RCCB to tell RCCB is inoperable.
(5) Install replacement RCCB (P1, P2 or P3) on position of the defective RCCB:
NOTE: It is necessary to do the test requested when all RCCB are installed.
(a) In EPDC1:
(b) In EPDC2:
1) For RCCB ATA 24 Ref. MP A350-A-24-71-57-09ZZZ-720Z-A.
ON A/C ALL
SUBTASK 247157-40100680001
NOTE: It is possible that RCCBs of the same P/N root are not interchangeable. It is necessary to refer to the applicable IPD task to
NOTE: It is mandatory to secure ATA28 RCCBs (refer to ATA28 MEL). If there is a monitoring failure on defective RCCBs
installed in the ATA28 position, these RCCBs have the status NO GO. To remove this status, it is necessary to use
Table 9
(1001KA)
4327XZ Ref. MP A350-A-24-71-57-07ZZZ-520Z-A
SPLY(1000QA)
4308XZ Ref. MP A350-A-24-71-57-0CZZZ-520Z-A
SPLY(1001QA)
4337XZ Ref. MP A350-A-24-71-57-03ZZZ-520Z-A
(3) Install the defective RCCB on position of the replacement RCCB (P1, P2 or P3):
FOR FIN 1001-KA or RCCB-APU START AC
(a) Install defective RCCB on position of APU start-AC RCCB (1001KA) Ref. MP A350-A-24-71-57-07ZZZ-720Z-A.
NOTE: It is not necessary to do the test requested in the installation procedure.
(b) Install defective RCCB on position of standby-supply-pump 2 RCCB (1000QA) Ref. MP A350-A-24-71-57-0CZZZ-720Z-A.
(c) Install defective RCCB on position of standby-supply-pump 1 RCCB (1001QA) Ref. MP A350-A-24-71-57-03ZZZ-720Z-A.
(4) Put a WARNING NOTICE(S) in position on defective RCCB to tell RCCB is inoperable.
(5) Install replacement RCCB (P1, P2 or P3) on position of the defective RCCB:
NOTE: It is necessary to do the test requested when all RCCB are installed.
(a) In EPDC1:
1) For RCCB ATA 24 Ref. MP A350-A-24-71-57-00ZZZ-720Z-A.
ON A/C ALL
SUBTASK 247157-40100700001
NOTE: The RCCBs which have the same P/N root must replace the NO GO RCCBs.
NOTE: It is possible that RCCBs of the same P/N root are not interchangeable. It is necessary to refer to the applicable IPD task to
(2) Remove the RCCB which will be used to solve NO GO Configuration on RCCB of:
SPLY (2000QA)
Table 11
SPLY (2000QA)
SPLY (2001QA)
(b) Install defective RCCB at location of main-supply-pump 2 RCCB (2001QA) Ref. MP A350-A-24-71-57-03ZZZ-720Z-A.
(c) Install defective RCCB at location of the ADGB-MCE-EMOT power RCCB (2008CV) Ref. MP A350-A-24-71-57-0BZZZ-
720Z-A.
(4) Put a WARNING NOTICE(S) in position on defective RCCB to tell RCCB is inoperable.
(5) Install replacement RCCB on position of the defective RCCB:
NOTE: It is necessary to do the test requested when all RCCB are installed.
(a) In EPDC1:
1) For RCCB ATA 24 Ref. MP A350-A-24-71-57-00ZZZ-720Z-A.
2) For RCCB ATA 27 Ref. MP A350-A-24-71-57-02ZZZ-720Z-A.
SUBTASK 247157-50000360001
F. Test after swapping of the RCCB
(1) Energize the aircraft electrical circuits
Ref. MP A350-A-24-41-XX-00ZZZ-761Z-A
6. Required Conditions
None
(1) Put on an ELECTRICALLY GROUNDED WRIST STRAP, and connect the wrist strap cable to the grounding connector (7) of
EPDC1.
FOR FIN 1011-MC or RCCB-GALLEY FEEDER 1 AC or FOR FIN 1031-MC or RCCB-GALLEY FEEDER 3 AC or FOR FIN 1051-MC
or RCCB-GALLEY FEEDER 5 AC or FOR FIN 1091-MC or RCCB-GALLEY FEEDER 9 AC or FOR FIN 1021-XP or RCCB-121XP or
FOR FIN 1023-XP or RCCB-123XP or FOR FIN 1025-XP or RCCB-125XP or FOR FIN 1027-XP or RCCB-127XP or FOR FIN 1033-X
P or RCCB-133XP
(2) Put on an ELECTRICALLY GROUNDED WRIST STRAP, and connect the wrist strap cable to a grounding point near the work
area.
4. Procedure
ON A/C 3501, 3502, 3503, 3504, 3505, 3506, 3507, 3508, 3509, 3510, 3511
CAUTION: BE CAREFUL WHEN YOU OPERATE THE RCCB SELECTOR KNOB. THIS COMPONENT CAN BE EASILY
DAMAGED.
SUBTASK 247157-10100940006
(2) Put the selector knob (5) to the 35A position. 35A
FOR FIN 1011-MC or RCCB-GALLEY FEEDER 1 AC or FOR FIN 1031-MC or RCCB-GALLEY FEEDER 3 AC or FOR FIN 1051-MC
or RCCB-GALLEY FEEDER 5 AC or FOR FIN 1091-MC or RCCB-GALLEY FEEDER 9 AC or FOR FIN 1025-XP or RCCB-125XP or
or RCCB-GALLEY FEEDER 5 AC or FOR FIN 1091-MC or RCCB-GALLEY FEEDER 9 AC or FOR FIN 2001-PE or RCCB-EMER TR
1 or FOR FIN 1001-PU or RCCB-TR1 or FOR FIN 2001-XH or RCCB-EMER ATU1 or FOR FIN 1021-XP or RCCB-121XP or FOR FI
N 1023-XP or RCCB-123XP or FOR FIN 1025-XP or RCCB-125XP or FOR FIN 1027-XP or RCCB-127XP or FOR FIN 1033-XP or R
CCB-133XP
(1) Installation of the RCCB
(a) Do a visual inspection and clean the component interfaces and the adjacent area.
(c) Make sure that all the electrical connections are clean and in the correct condition.
(d) Put the RCCB (2) in position on the current transformer plate (3) and engage the locating pins (4) in the related holes of
(f) Apply a drop of 04TME5 (Varnish_- Marking System) on the captive screws (1) and on the RCCB (2).
ON A/C 3501, 3502, 3503, 3504, 3505, 3506, 3507, 3508, 3509, 3510, 3511