Professional Documents
Culture Documents
K8060
or
p e ak e r system tre
s
r active me thea
Ideal fo guitar amp, ho , etc.
fer, amp
subwoo s, instrument
syste m
Specifications:
Excellent value for money
Full discrete design using Epitaxial Darlington transistors
DC supply circuit on board with LED indication
Ideal for active speaker system or sub woofer, guitar amp, home theatre systems, instruments amp….
Comes complete with transistor isolators, spacers and bolts
Overload and short circuit protection
Features:
200W music power @ 4 ohm load
100Wrms power @ 4 ohm load
70Wrms power @ 8 ohm load
Distortion: 0.02% @ 1KHz/10W
Damping factor: >800
Frequency response: 3Hz to 200KHz (-3dB)
Sensitivity: 0.6Vrms
Signal to noise ratio: 115dB
Power supply: 2 x 25-30Vac / 100 - 120VA
PCB dimensions: 107x62mm (aprx.) :
Recommended power transformer: 12030
Recommended heat-sink: HSVM100 (pre-drilled) or S44/75 (not drilled)
2
Assembly hints
3
Assembly hints
1- Mount the component against the PCB surface and carefully solder the leads
4
Construction
R1 : 47K (4 - 7 - 3 - B)
R2 : 100 (1 - 0 - 1 - B)
5
Construction & connection
6
Construction
13. 5W resistors
R...
R19 : 0,47
R20 : 0,47
2mm
IMPORTANT
14. Electrolytic Capacitors.
Watch the polarity ! Check the complete assembly carefully before
C12 : 3300µF mounting the heat sink.
C13 : 3300µF
Once the heat sink is mounted, the solder-side
is no longer accessible.
C...
7
Final Assembly
Fig. 1.0
8
Final assembly
• Mount 4 bolts + 8 nuts (PCB support). (fig.2.0) • Slide the PCB over the 4 bolts, and fix using 4 nuts
(Fig 3.0).
2 x M3 nut
9
Transistor T6
Fig. 4.0
10
Transistor T6
• Insert the transistor (BC547) in the hole (Fig. 5.0). Pay attention to the position of the transistor (fig 6.0)!
BC547
Fig. 5.0
Fig. 6.0
• Carefully bend the leads and solder them to the connector T6, see
figure 7.0.
Fig. 7.0
11
Power transistors
• Mount the isolation mica onto the heat sink, check the position of the hole. plastic isolation
washer
and nut.
IMPORTANT: If metal body transistors are used, a plastic
isolation washer must be applied (see 9.0.)
M3 bolt
Heat conductive
Fig. 9.0 compound
m Fig. 8.0
m
-4
+/
M3 bolt
12
Power transistors
• Solder the connections of the power transistors with the pin headers, see fig. 10.
Fig. 10
13
Test & adjustments
14
Test & adjustments
*
1A T (slow-blow) fuse
2 x 25 to 30Vac transformer
*
mains
*
- + VOLUME CONTROL 47K Log.
*
AC
0 0 *
AC
4 - 8 Ohm
*
Inputsignal * optional
15
Test & adjustments
• Turn the RV1 bias adjust trimmer fully counter clockwise (turn left) before applying power for the first time.
ADVICE: For safe first-time testing insert a 60W light bulb in series with the AC power and the trans-
former. If the light bulb lights up continuously, disconnect the transformer and check all your wiring and
assembly. Reconnect the power supply. If the lamp remains off, everything is OK, replace the light bulb
with a fuse.
Final connection:
• The input (GND and in) can be connected directly to an audio source (pre-amp or mixing panel) or a vol-
ume control (potentiometer) can be used (see diagram).
• Connect the speaker (4 ohm or higher) to the connections LS+ and GND.
CAUTION: VOLTAGES OF ABOUT 80V ARE PRESENT. MAKE SURE TO USE A SUITABLE ENCLO-
SURE AND ISOLATE ALL AC CONNECTIONS
17
PCB
18
Diagram
20. Diagram
+40V
SK4 D6
AC
1N5404 +40V
C13 +40V
D5 C7 R18
SK6 C5
4700µ/50V 100nF 33K
AC-0
1N5404 680p
SK5 D4 R12
1K5 T8
AC-0 GND GND C8 LD1 TIP142
C12 LED3RL
1N5404 100nF
4700µ/50V
SK3 D3
D1
AC +40V 1N4148
1N5404 -40V R13
3K3
R11 T4 Bias current (cold)
BC547 R17
3K3 10-15mV over R19
220R
R16 R19
R14 47R 0.47 / 5W
1K8
ZD1 R9 SK8
3K3 C10
ZB9V1 LS+
100µ/50V
500R T6 C6
GND RV1 BC547 R6 R20
Bias adj. 47R 0.47 / 5W
T1 T2
SK2 C9 BC640 BC640 47nF
R8 T5
In BC557 R5
SK7
3K3 R10
10µF R15 220R LS-
C3 10
R7 1K
R1 R3 T7
C2 47K 3K3 TIP147
680R 47p D2
47p C1
C11 R4 1N4148
-40V
GND GND
SK1 47p 330R
470µ/16V C4
R2 T3
GND 100R BC639
680p
-40V -40V
GND Title
K8060 100W amplifier
19
VELLEMAN Components NV
Legen Heirweg 33
9890 Gavere
Belgium Europe
www.velleman.be
www.velleman-kit.com