Professional Documents
Culture Documents
1 - Setup W7 For MS4.2
1 - Setup W7 For MS4.2
Disclaimer of Warranties
The Licensor expressly disclaims any and all warranties relative to the Software. THE SOFTWARE IS
PROVIDED “AS IS," WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING,
WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR OF
PARTICULAR PURPOSE AND NON-INFRINGEMENT AND THE ENTIRE RISK AS TO THE QUALITY
AND PERFORMANCE OF THE LICENSED PRODUCT IS WITH YOU.
Limitation of Liability
In no event shall the Licensor be liable for any direct, special, incidental, indirect or consequential
damages whatsoever to you (including, without limitation, damages for loss of profits, sales or data or for
business interruption) arising out of the use of or inability to use the Software, even if the Licensor has
been advised of the possibility of such damages. In any event, the Licensor's entire liability under any
provision shall be limited to the greater of the amount actually paid by you for the Software or $25.
Because some states and jurisdictions do not allow the exclusion or limitation of liability, the above
limitation may not apply to you. If any provision of the Software License Agreement is declared by a court
of competent jurisdiction to be invalid for any reason, such invalidity shall not effect the remaining
provisions hereof.
Governing Law
This Software License Agreement shall be governed by the laws of the State of New York without regard
to conflict of laws principles.
Term
This License Agreement is effective until terminated. You may terminate this License Agreement by
returning the Licensed Product to Licensor. Licensor may terminate this License Agreement if you breach
any of the terms and conditions. Upon termination of this License Agreement for any reason, you shall
return the Licensed Product to Licensor. All provisions of this Agreement relating to disclaimers of
warranties, limitation of liability, remedies, or damages, and Licensor's proprietary rights shall survive
termination.
YOU ACKNOWLEDGE YOU HAVE READ AND UNDERSTAND THIS AGREEMENT AND AGREE TO
BE BOUND BY ITS TERMS. YOU FURTHER AGREE THAT THIS AGREEMENT IS THE COMPLETE
AND EXCLUSIVE STATEMENT OF THE AGREEMENT BETWEEN YOU AND LICENSOR, AND
SUPERSEDES ANY PROPOSAL OR PRIOR AGREEMENT, ORAL OR WRITTEN, AND ANY OTHER
COMMUNICATIONS RELATING TO SUBJECT MATTER OF THIS AGREEMENT.
NY-177971 v3 0950000-102
Overview
This universal guide is intended for retail labs running FUJIFILM systems regardless of
location.
Important: Review this entire guide to determine which sections apply to your lab before you
begin installing any software.
®
This setup guide provides details and instructions for setting up Windows 7 operating systems prior to
installation of FUJIFILM’s Frontier Workflow Management Software (MS01) for retail lab systems
internationally. It may need to be used in association with a regional or retail client-specific guide.
Windows® 7 Installation
®
Important: This section refers to parts of the Windows 7 installation requiring specific settings in
®
order to adequately support MS01 4.0. Refer to this section while installing Windows 7.
Drive Setup
Important: There must be a minimum of one drive with at least two partitions, or two drives each
having their own partition. Each drive should have a minimum storage space of 40GB.
2 Click Next.
5 Click Next.
c. Click Apply.
An Install Windows dialog box may display with a message about additional partitions
that Windows might create for system files.
d. Click OK.
®
e. Complete Windows 7 installation.
d. Click Apply.
Note: A dialog box may open warning you that extending a partition is not a reversible
action. Click OK to dismiss the dialog box and continue.
®
e. Click Next to complete installation of Windows 7.
When installation is near completion, Windows boots for the first time.
f. Once installation is complete the Set Up Windows screen displays – proceed to the next
section.
2 Click Next.
5 In the Type a password hint field, you may type a hint Windows will display in the event you forget
the password.
®
6 Continue with the Windows 7 installation.
2 Click Next.
8 Click Next.
9 Click Next.
10 In the Simple volume size in MB field, type a value no less than 40960.
11 Click Next.
13 Click Next.
14 Click Next.
15 Click Finish.
The wizard closes and the new drive partition setup is complete.
Overview
In this section, you will learn how to:
Access the Control Panel (see page 23)
Modify Display (see page 24)
Modify Folder Options (see page 27)
Modify Indexing Options (see page 30)
Modify Personalization Options (see page 34)
Modify Power Options (see page 39)
Modify User Accounts (see page 45)
Important: Complete all instructions in each sub-section of this section before moving onto the
next section.
Open the Control Panel and set the View by option to Small icons.
1 ®
Select the Windows menu button located at the bottom-left corner of the screen.
®
The Windows Start Menu displays.
The Display Settings dialog box closes and the Screen Resolution screen returns to focus.
6 Click OK.
6 Click Apply.
7 Click OK.
The Folder Options dialog box closes and the Control Panel returns to focus.
7 Click OK.
8 Click Close.
The Indexing Options dialog box closes and the Control Panel returns to focus.
d. Click Apply.
e. Click OK.
The Screen Saver Settings dialog box closes and the Control Panel > Personalization
screen returns to focus.
11 Click Apply.
12 Click OK.
The Power Options dialog box closes and the Change settings for the plan: Balanced menu
screen returns to focus.
User Accounts
1 From the Control Panel, click User
Accounts.
4 Click OK.
11 Click Apply.
12 Click OK.
13 All Control Panel settings are now complete. You may close the window and move on to the next
section of this guide.
Overview
In this section, you will learn how to:
Modify Recycle Bin Settings (see page 51)
Modify Network Card Settings (see page 53)
Modify Group Policy Settings (see page 62)
Modify Windows Firewall Settings (see page 67)
2 Select Properties.
6 Click Apply.
7 Click OK.
The Recycle Bin Properties dialog box closes and the settings are saved.
4 Click Properties.
6 Click Properties.
8 Click OK.
9 Click OK.
10 Click Close.
The Local Area Connection Status dialog box closes and the Network and Sharing Center menu
returns to focus.
13 Select Properties.
14 Click Configure.
17 Click OK.
18 Repeat steps 4-9 for each network card displaying in the list on the Network Connections screen.
19 When settings to all network cards are complete, close the Local Area Connection Properties
dialog box and move on to the next section of this guide.
Group Policy
®
1 Select the Windows menu button located at the bottom-left corner of the screen.
®
The Windows Start Menu displays.
9 Click Apply.
10 Click OK.
3 Select the Turn off Windows Firewall radio button for each item displayed on the screen.
4 Click OK.