Professional Documents
Culture Documents
MDSP Preboard 2011 Set A
MDSP Preboard 2011 Set A
22. The formula to find out the number of turn of the crank
simple indexing is
A. T=20/N C. T=N/20
B. T=40/N * D. T=N/40
23. In a standard dividing head the ratio between the worm wheel
and the worm is
A. 10:1 C. 20:1
D. 30:1 D. 40:1 *
28. All four compression coil spring support one load of 700
kg/mm. All four springs are arranged in parallel and rated
same at 0.609 kg/mm. Compute the deflection in mm.
A. 64 C. 178
B. 147 D. 287 *
30. A 60 inch diameter steel pipe, 3/8 inch thick, carries water
under a pressure head of 550 ft. Determine the hoop stress
in the steel.
A. 34,320 psi C. 19,066 psi *
B. 25,780 psi D. 15,920 psi
31. The maximum moment induced in a simply supported beam of 20
ft span, by a 2000 pound load at midspan is
A. 125,000 ft – lb C. 30,000 ft – lb
B. 15,000 ft – lb D. 10,000 ft – lb *
32. Determine the length of belt needed for a two flat belt
pulleys having a diameter of 70 cm and 30 cm. The center
distance is 400 cm and pulleys rotate in same direction.
Assume power transmitted is 10 hp at 200 rpm.
A. 958 cm * C. 589 cm
B. 859 cm D. 895 cm
41. Mark the milling method during which the formation of the
chatter marks is very likely
A. during down cut milling with a straight tooth cutter.
B. during up cut milling with a straight tooth cutter. *
C. during face milling with a straight tooth cutter.
D. while using spiral tooth cutter.
42. Mark the cutter which works simultaneously with up cut and
down cut process
A. Side milling cutter.
B. Semi-circular milling cutter.
C. Shell end mill. *
D. Plain milling cutter.
60. In the selection of wire rope, regular lay means wires and
strands are arranged in the following manner:
A. twisted in the same direction
B. twisted in opposite direction*
C. twisted in any direction
D. twisted in along direction
66. The cast iron flywheels are commonly designed with a factor
of safety of______
A. 14 to 15 C. 8 to 9
B. 10 to 13 * D. 6 to 12
71. The use of hardened steel for the mating metal gear appears
to give the best results and longer operational life. The
usual hardness is in the range of-
A. over 600 BHN * C. below 350 BHN
B. 300 to 400 BHN D. over 400 BHN
76. Find the torsional moment in N-m developed when the shaft
delivers 40.2 hp at 260 rpm.
A. 901 x 10 to the 3rd power C.1102 x 10 to the 2nd power
B. 901 x 10 to the 2nd power D.1102 x 10 to the 3rd power *
78. A pair of gear and pinion having a ratio of 4 with the gear
having 100 teeth and the pinion with 25 teeth. Find the
circular pitch, if the center distance is 15 and the pitch
is at 6.
A. 0.94 C. 0.610
B. 0.754 * D. 0.552
83. A bolt has a tensile load of 300 lbs. The bolt is made of
SAE 1040 material with Sy = 55 ksi, what is the stress area
of the bolt?
A. 0.1023 in2 * C. 0.327 in2
B. 0.1230 in2 D. 0.5190 in2
88. The torsional deflection of steel shaft is 0.6 deg per meter
length. The shear stress is 60 MPa. Compute the diameter of
the shaft in mm. Steel modulus of elasticity is 79 GPa.
A. 90 mm C. 130 mm
B. 105 mm D. 145 mm *
97. When preparing to tap a hole, the size of the drill will be
A. equal to the size of the tap
B. larger than the size of the tap
B. smaller than the size of the tap *
D. none of the above
98. When preparing to tap a hole for a pipe fitting the size of
the drill will be :
A. larger than the tap size *
B. smaller than the tap size
C. equal to the size of the tap
D. none of the above