Professional Documents
Culture Documents
03 IP-20G Introduction - 0316 - v5
03 IP-20G Introduction - 0316 - v5
March 2016
Version 5
Agenda
C C
1+1 1+0
C C
IP-20N
C
C
2+0
1+1
C
IP-20N
C
C IP-20N
1+0 C C
C
1+0
2+0
C
2+0 1+0
IP-10G C C
IP-20N
IP-20G
C C
IP-20G IP-10G
IP-20G Introduction
IP-20G hardware characteristics:
• 6 x 1 GE interfaces total
• 2 x dual mode GE electrical or cascading interfaces (RJ-45)
• 2 x GE electrical interfaces (RJ-45)
• 2x GE optical interfaces (SFP)
• Optional: 16 x E1 interfaces
• Single or dual radio interfaces (TNC)
• Single or dual power-feeds (-48v)
• Sync in/out interface
• Management interfaces
• Terminal – RS232 (RJ-45)
• 2x FE electrical interfaces (RJ-45)
• External alarms interface
• RFU-C/Ce, RFU-HP (1Rx or 2Rx), RFU-Ae/Aep support
• IEEE-1588 TC
• IP-20G maintains high capacity, with up to 1024QAM modulation in its first SW release (T7.7),
and up to 2048QAM from SW release T8.0
Reference Configurations
6
IP-20G Dual Modem Activation
• A single-carrier IP-20G unit with dual-modem hardware can be converted via
software upgrade to a dual-modem unit
12
FibeAir IP-20G – Front panel description
Passive cooling
(Fan-less design)
1RU
Power
16 x E1/DS1s External
1 or 2 RFU -48V DC
(optional) Alarms 2 x FE
2 x GE interfaces (Single-feed &
MDR69 connector (DB9) Management via
Optical (TNC) Dual-feed options)
splitter cable 2 x Dual-Mode: (SFP)
(RJ45) GE Electrical or
Sync in/out
‘Cascading’
(RJ45)
Terminal (RJ45) 2 x GE
(RJ45) Electrical
(RJ45)
SM- Card
• The SM-Card holds the configuration and software for the IDU. The SM-
Card is embedded in the SM-Card Cover, so re-using the existing SM-Card
Cover is necessary to ensure that the unit’s software and configuration is
maintained.
• Contains only software with configuration
• If the user only needs to use a single management interface, a standard Cat5 RJ-45 cable (straight or
cross) can be connected to the MGMT interface.
• To access both management interfaces, a special 2 x FE splitter cable can be ordered from Ceragon.
• Port Status LED – The LED for management interface 1 is located on the upper left of the MGMT
interface. The LED for management interface 2 is located on the upper right of the MGMT interface.
E1/DS1 - Interface
• Optionally, FibeAir IP-20G can be ordered with an MDR69 connector in which 16
E1/DS1 interfaces are available (ports 1 through 16).
• In SW 7.7. is E1 option only available
• In SW 7.9. also DS1 option available
• The E1/DS1 interface has the following LEDs
• ACT LED – Indicates whether the TDM card is working properly (Green) or if there is
an error or a problem with the card’s functionality (Red).
• E1/DS1 LED – Indicates whether the interfaces are enabled with no alarms (Green),
with alarms (Red), or no interfaces enabled (Off).
• FibeAir IP-20G receives an external supply of -48V current via one or two power
interfaces (the second power interface is optional for power redundancy).
• The IP-20G monitors the power supply for under-voltage and includes reverse
polarity protection, so that if the positive (+) and negative (-) inputs are mixed up, the
system remains shut down.
• The allowed power input range for the IP-20G is -40V to -60V. An under voltage
alarm is triggered if the power goes below the allowed range, and an over voltage
alarm is triggered if the power goes above the allowed range.
Synchronization Interface
• FibeAir IP-20G includes an RJ-45 synchronization interface for T3 clock input and T4 clock output.
The interface is labeled SYNC.
• The synchronization interface contains two LEDs, one on the upper left of the interface and one
on the upper right of the interface, as follows:
• T3 Status LED – Located on the upper left of the interface. Indicates the status of T3 input clock,
as follows:
• Off – There is no T3 input clock, or the input is illegal.
• Green – There is legal T3 input clock.
• T4 Status LED – Located on the upper right of the interface. Indicates the status of T4 output
clock, as follows:
• Off – T4 output clock is not available.
• Green – T4 output clock is available.
• Blinking Green – The clock unit is in a holdover state.
Terminal Interface
• FibeAir IP-20G includes an RJ-45 terminal interface (RS-232). A local craft
terminal can be connected to the terminal interface for local CLI
management of the unit.
48V
Radio Interface 1
Power
48V Supply Framer Modem IF
RFU
Interface RFU
(Optional Dual
Feed)
ABC/BBS XPIC
Sync
Radio Interface 2
Sync
In/Out Sync Unit (Optional)
FE Management
Interfaces
CPU
Terminal
Ethernet
Ethernet Services
TDM Interfaces
GE Traffic
Interfaces
(Optional)
Network
Processor TDM
16 x E1
TDM Pseudowire Services Services Framer LIU
Interface
Processor
GE/Cascading Services
Interfaces
Engine
TDM Cross
Connect
Native TDM
Services
2x 1+0 EW
2+0 XPIC
2+0 ABC
Traffic Aware “Smart Pipe”
Traffic Manager
Multi Service, Carrier Ethernet 2.0 Switch
25