Professional Documents
Culture Documents
© Craftsy 1
SEW STURDY: THE ESSENTIAL BACKPACK with Annie Unrein
Labels
Keep track of all your pieces easily! Print and cut out these labels to pin to your fabric, stabilizer and interfacing pieces
as you cut them.
PIECES TO BE QUILTED
*If you are planning to quilt the fabric on a longarm or midarm machine, cut ONE 30" x 36" piece from Main Fabric,
Lining, and Foam Stabilizer instead of two smaller pieces. Sandwich and quilt the 30" x 36" pieces as one, then cut out
the necessary pieces.
© Craftsy 2
SEW STURDY: THE ESSENTIAL BACKPACK with Annie Unrein
TO CUT FROM UNQUILTED MAIN FABRIC, LINING FABRIC, FOAM STABILIZER, MESH FABRIC & CONTRASTING FABRIC
Contrasting Fabric
Bias Binding
18" x 18"
© Craftsy 3
SEW STURDY: THE ESSENTIAL BACKPACK with Annie Unrein
A. Cut B. Quilt
Note: Cutting dimensions are length of fabric x width of fabric. •
Make two quilt sandwiches by layering the 27" x
For best use of fabric, cut in the order listed, referring to 18" pieces of fabric (main fabric and lining fabric)
layouts on page 3. Labels for all pieces are provided on page 2. with the foam stabilizer between them. Smooth
layers together and pin or spray-baste to hold
CUT FROM MAIN FABRIC layers together
The Essential Backpack
• Body of backpack and pockets (to be quilted): Two • Quilt as desired. If you are quilting the fabric on a
27" x 18"* home machine, it's easiest to quilt vertical lines
• Flap Facing: 3½" x 10½" about 1" apart across the fabric.
sson • 1. Pocket
Cutting & Quilting
E Facing: 2½" x 10½" • For the backpack shown in class, the fabric was quilted
*TIP: If you are quilting the fabric on a longarm, cut ONE
on a longarm machine using an all-over design.
CUT FROM LINING FABRIC 30”L x 36”W piece from main fabric, lining, and Soft and
ut. Stable. That will leave enough fabric to cut the remaining
• Lining of backpack and pockets (to be quilted): Two
27" x 18"* unquilted C. Cut from Quilted Fabric & Seal Edges
pieces.
TE: Cutting dimensions are length of fabric x width of
• use
ic. For best Pocket B: 4" cut
of fabric, x 10½"
in the order listed. • From one quilted fabric panel, cut these pieces:
• Front Flap Facing: 3" x 7" 3. Cut from quilted fabric and seal edges.
• Backpack Front: 12½" x 10½"
Labels for all pieces are on page 9. (Note: All measurements are listed
• Backpack as12½"
Back: length x width.)
x 10½"
CUT FROM CONTRASTING FABRIC
rom the main fabric cut these
• Straps/Strap pieces:
Tabs: Two 2¾" x 42" • Side Strip: 21" x 5"
Body• of backpack
Zipper Pulls: 1" x 42"(to be quilted) —
and pockets
two* 27” x 18” a. From one quilted 18”
• Bias Binding: 18" x 18" fabric panel, cut
Flap Facing — 3½” x 10½”
• Pocket D: 11" x 10½" these pieces:
Pocket E Facing — 2½” x 10½”
• Pocket C: 4½" x 10½"
rom the lining fabric cut: Backpack Backpack
• Pocket A: 4" x 10½" Front — 12½”
Lining of backpack and pockets Front
• Padded Handle: 4" x (to
11" be quilted) — x 10½”
two* 27” x 18”
• Pocket E and F Bindings: Two 2" x 10½" 12½” x 10½
Side Strip
Pocket B — 4” x 10½” Backpack
• Side Strip Bindings: Two 2" x 4½"
21” x 5”
Front Flap Facing — 3” x 7” Back—12½” x
10½” 27”
CUT FROMfabric
rom the contrasting FOAMcut:STABILIZER (BYANNIE'S SOFT AND
STABLE)
Straps/Strap Tabs — two 2¾” x 42” Side Strip —
21” x 5”
Backpack
Zipper
• Pulls — 1” x 42”
Stabilizer for body of backpack: Two 27" x 18"* Back
Bias• Binding — 18”for
Padding x 18”
Padded Handle: 1⅞" x 11"
Pocket D —11” x 10½” 12½” x 10½”
PocketCUT
C— FROM
4½” xMESH
10½” FABRIC
• Pocket G1:
Pocket A — 4” x 10½” 2" x 11"
•
Padded Handle — 4” x10½"
Pocket G2: 11” x 11"
Pocket E and F Bindings — two 2” x 10½”
Side CUT
Strip FROM FUSIBLE
Bindings — two 2”INTERFACING
x 4½”
• Front Flap Facing Interfacing: 3" x 7"
• Pocket
rom ByAnnie’s Soft and Stable®
E Facing cut:
Interfacing: 2½" x 10½" • From the second quilted fabric panel, cut these pieces:
b. From the other• Pocket E: 9¾" x 10½"
• Pockets
Stabilizer for body of
A, backpack — two* 27”
B, C Interfacing: x 18”
Three 2" x 10½"
quilted fabric panel,
• Pocket F1: 1½" x 10½" 18”
• for
Padding Padded
Pocket Handle — 1¾”
D Interfacing: x 11”
5¼" x 10½" cut these pieces:
• Pocket F2: 9" x 10½"
rom mesh
*Iffabric
you are quilting the fabric on a longarm or midarmPocket E —• Front Flap: Pocket
cut: 3" x 7" E
Pocket G1 — 2”cutx 11” 9¾” x 10½”
machine, ONE 30" x 36" piece from main fabric, lin- • Zipper Strips: Two 21" x 2"
Pocket
ingG2 and —10½”
Soft xand
11”Stable. Quilt the large piece and cut
all Pocket F1 — 9¾” x 10½”
of your quilted-fabric pieces from it. 1½” x 10½”
Zipper Strips
two, 21” x 2”
p
21” x 5”
Backpack
Back
12½” x 10½”
SEW STURDY: THE ESSENTIAL BACKPACK with Annie Unrein
(main fabric).
Pocket F2 — Pocket F1 " • Fuse a 2" x 10½" Pocket A, B, C Interfacing to the
9” x 10½” 1½” x 10½”
bottom half of the wrong side of each of Pockets A,
Front Flap — 27” Pocket F2 B and C (lining and contrasting fabrics).
3” x 7” Note: On Pocket C, align the interfacing ¼" up from the
Zipper Strips 9” x 10½” bottom edge.
— two 21” x 2” • Fuse the 5¼" x 10½" Pocket D Interfacing to
the bottom half of the wrong side of Pocket D
Front Flap (contrasting fabric), aligning the interfacing ¼" up
3” x 7” from the bottom.
Note: Use ¼" seam allowances unless directed otherwise.
eal the edges of
h quilted piece
titching 1/8”
m edge around all the edges of each quilted piece you've cut, as
• Seal
s. shown in the class, by stitching ⅛" from the edge
around all sides.
AU 2
© Craftsy 5
gs. Strap/Strap Tabs
(contrasting fabric) in
he 3” x 7” interfacing to the wrong side of half lengthwise (1⅜” TIP:
Front Flap Facing (lining fabric). x 42”). Stitch SEW alongSTURDY: Use a turning tool such
THE ESSENTIAL BACKPACK with Annie Unrein
e 3½” x 10½” interfacing to the wrong side Strap/Strap
long edge (see Tabs TIP as a Quick Turn tool to
ngs.
x 10½” Flap Facing (main fabric). at(contrasting
right); pressfabric) seamin make this extra easy. Or,
the 3” x 7” interfacing to the wrong side of
e 2½” half
open. lengthwise
Turn right (1⅜”
side save the selvage TIP: edges
7” Frontx Flap 10½”Facing interfacing (lining tofabric).
the 2½” x 10½”
x 42”). Stitch along Use
that youa turning
cut off tool
fabric such
Facing out; press, placing
he 3½”(main fabric).
½” 2”xx 10½”
x 10½”
10½” Flap
interfacing to the wrong side
pieceFacing of interfacing
(main fabric). to bottom half
Bindings, Handles, Straps, Strap
long
seam edge
in center(see of TIP as
pieces. a Tabs
Quick
makesturdy
Insert
this extra
& Flap
Turn
one tool
of
easy.
to
Or,
at right); press
tube. seam
Strap/Strap Tabs these strips (at
se interfacings.
ide of each of Pockets A, B, and C (lining open. Turn right side save
least the
48” selvage
long) inside edgesthe
he 2½” x 10½” interfacing to the 2½” x 10½” b. Fasten a large (contrasting fabric) in
asting a.fabrics). NOTE:3” x 7”On Pocket C, that you cut off fabric
Facing
t ¼”the
Fuse
up 3”
(mainthe
from
fabric).
the bottom.
interfacing to the wrong side of out; press, placing
safety pin to one halfend lengthwise (1⅜”piece and catch TIP:
folded
a 2” x 10½” A. x 7”Prepare
Front Flap Facing
piece of interfacing Bias Binding
(lining
to bottom
fabric). Strips
half
seam in center
of a 42” piece xof42”). 1”• Stitch
of With thepieces.
end
wrong sides
along
these
inInsert
sturdy
a seam Useone
strips
aofturning fold
across
together,
(at
tool suchthe strip in half
e 5¼”
b. xFuse10½”the interfacing
3½” x 10½” to the bottom half
interfacing to the wrong side tube. long edge the
lengthwise
(see short
TIP edge
and as at the
pina every top. Turn
Quick 3-4" to tooljoin.
to Do not press.
side of each of Pockets A, B, and C (lining strapping and pull
ng side of the of• Pocket
3½”Use xNOTE:Dthe
10½” 18" Bias
(contrasting
Flap Facing Binding
fabric),
(main square (contrasting fabric).
fabric). b. Fasten a largeat right); press Note:
least you’ve
When seam
48” long)
By pinningstitched make inside
without this the
the extra easy.
pressing, you'llOr,get a smoother
rasting fabrics). On Pocket C, into strap, trimming folded
e interfacing ¼”
ngs. Annie up from prefers the bottom.to use a 2¼" binding for a tighter safety fit.
Strap/Strap pin to Tabs
one
open. end Turn long
right sidepiece
side and and pressed
save catch
the selvage edges
it ¼” b. upFuse from thethe 2½”bottom.
x 10½” interfacing to the 2½” x 10½” ends even with the binding. theseam,
end inpull a seam across
Less experienced bag makers may prefer fabric. 2½"(contrasting
of astrips.
42” fabric) in placing the on the
that you end cut off fabric
hethe5¼” Pocket
3” xx7” 10½” E Facing
interfacing
interfacing (main
to the to fabric).
wrong
the bottom side half of Bepiece
careful of to
out; 1”press,
the short TIP:
edge at the top. one of
• Cut the 18" square of fabric in half diagonally half
(figure
strapping lengthwise
1).
and pull
seam (1⅜” in center of the
of selvage strip
pieces. to Insert
7” Front Flap keep the seam
ong
INDINGS,
side
c. Fuse aFacing
of Pocket 2” x 10½”
HANDLES, D (lining
(contrasting
piece fabric). fabric), to bottom half
of interfacing When
Use easy ayou’ve
turning stitched
tool
of such the strips (at
the 3½”
he interfacing
of wrongx 10½” ¼”
side interfacing
up
of eachfrom the to Pockets
of the
bottom.wrong A, side
B, and C (lining
x 42”).
into
allowance strap,
long even
Stitch
edge with
trimming
centered
along
tube.
(see the TIP
B. Make make
as athe
long
turning side
the and
Quick Padded
work these
Turn
tube pressed
sturdy
tool
right-
Handle
tolong)
RAP
½” x and TABS,
10½” Flap and
Facing FLAP.
(main
contrasting fabrics). NOTE: On Pocket C, fabric).
figure 1 ends
on one side
at right); and
press b. to
Fasten
seam• With a largethe
sidemake seam,
out.
wrong this
Cut pull
least
extra
sides off ontop
48”
the
easy.end
together, endOr,and
inside the
foldcatchthe 4" x 11" Padded
fabric.
keep theBe careful
strapping to folded piece
ess2½” directed
position itotherwise.
¼” up fromtothe safety pin to one of end
the selvage strip toin a seam
the x 10½” interfacing thebottom.
2½” x 10½” open.
keep
and fabric
Turn
the seam right side
fromof a 42” piece make Handle save
along the
with
(contrasting selvage
the endedges
strip.
fabric) in half
acrosslengthwise;
BINDINGS, HANDLES, out; press,centered placing of 1” you
that easy cutworkoff of
fabric
E Facing
d. Fuse (main the
nding strips using the 18” Biasfabric).
5¼” x 10½” interfacing to the bottom half allowance
twisting. Smooth the press. Open the the
fabric short andedge at
bring the
eachtop. raw edge to
seam inside
center strapping
of and turning
pull
pieces.the Inserttube one right-
of
RAP
a 2” of
ntrasting TABS,
the
x 10½” wrong
pieceNOTE:
fabric). and
side ofFLAP.
of interfacingIPocket
prefer to D bottom figure 1 fabric),
(contrasting half on
fabric one over theand to
into strap, trimmingthe pressed
side
these out.sturdy line When
Cut long in
off
strips the
top
you’ve
end
(at middle; stitchedpress theagain.
tube.the strapping side and pressed
gnless foraligning
gside aof eachthe
tighter
directed of interfacing
Less- A, ¼”
Pockets
fit.otherwise. B, andup from C (liningthe bottom. keep
strapping. Remove ends• even the Open
safety
withalong pin and
out
the
least again;
with
48” topstitch
center
selvage
long) inside thethe
strip.the 1⅞" x 11" Padded Handle
trasting
akers may preferNOTE:
fabrics). 2½” strips. On Pocket C, and
b.
straps fabric
Fastenalong from
a large
the edges. Set aside. the seam, pull on the end
fabric. BeFoam careful to piece and
Stabilizer
folded piece catch inside. Foldtofabric over foam
twisting. Smooth the of the selvage strip
Binding
n it ¼” up strips
• fromusing
Withthe rightthe 18”
bottom. sides Biastogether, sew the two triangles c.safety
together
From pin
each to 42”onestrip,
keep endthe cutseam one
stabilizer the 4½” end piece
along in a to
seam make
pressed across lines. Fold in half again;
SSON 18” square
ontrasting
the 5¼”
2.10½”
x
BINDINGS,
of fabric
fabric). in halfI prefer
NOTE:
interfacing
along one to
short HANDLES,
theside bottom
figure
2(figure half 2). Press seam
fabric
open.
of a 42”
two Strap Tabs.
over piecethe of 1”
allowance
The remaining centered the 37½”short strips
edge
make easy work of
will
at be
the top.
(figure
for a1). strapping. Remove the thesafety folded piece now
turning measures
the tube 1" x 11". Secure edges
right-
RAPS,ng
rong sideSTRAP
tighter fit. Less-
of Pocket D TABS,(contrasting andfabric), FLAP. figure 1 strapping and
used for the Straps. onpull oneSet sidethose and topin and
aside.
When you’veside
topstitch
stitched the off top end
makers
ht may prefersew 2½”the strips. straps
into along
strap, the
trimming edges. Set
with aside.
clips or pins and out. sew Cut all around the handle,
thesides
¼” seams
together,
interfacing unless ¼” up fromtwo
directed the bottom.
otherwise. 4. Assemble theeven Strap keep
Tabs. the strapping long side andalong pressed with selvage strip.
ogether along one short side ends
c. From eachand with the
42” fabric around
strip, cut fromone the 4½”⅛"
seam,from piece the
pull to edge;
onmakethe end set aside.
ePress 18” square of fabric in half figure
epare seam
Bias open.
Binding strips using the 18” Bias
a.two With
fabric.Strap seam
BeTabs. side
careful down,
The
twisting. insert the
to remaining
Smooth one37½” endstrips of a will4½”be
y (figure 1). 2 of the selvage strip to
figure 3I prefer Strap
keepTab
used thethe
for into
seam the opening
Straps.
fabric Set the
over of a 1”
those rectangle ring.
aside.
engresulting
BINDINGS, square (contrasting HANDLES, fabric). NOTE:
ght
eam, a sides
2¼” together,
cut binding forsewa tighterthe two fit. Less- figure 1
Bring
4. Assemble
allowanceends ofcentered
the Strap
Strap
strapping.
Tabs.
C.TabMake together
Remove
make
turning
thethethe Straps
easy work of
safety
tube pin right-
& topstitch
and Strap the Tabs
TRAP together
rienced TABS,
along one andshort
or 2½” bag makers may prefer 2½” strips.
FLAP.
side 2¼” - 2½” (seam
on one onsideinside), and
straps matching
to along the
• down,
rawedges. Set aside.
sideone out.end Cutofoff figure 5
.nless
Pressdirected
seam open. 2¼” - 2½”
a.
edges,
keepWiththe seam
making strapping side
a tab aboutWIth 1” right
insert x 2¼”.sides a top
4½”end fold each 2¾" x 42"
together,
otherwise.
!s
g 2½”
but might 2¼”
be easier - 2½” to open. a. With seam Note: side
Use down,
a turning insert toolone suchendas of aa Quick
4½” Turn tool to make
(figure 2). Press seam 5. PrepareedgeFront Flap.
m
figure
figure 4 figure 3 42” strip, cuteasy, one 4½”
or savepiece the make edges that you cut off fabric
e 18”c.square
From the of fabric
2¼” -in2½”
resulting half a.b.Using
Repeat a 2½” circular object (such as Template A, a
ure
ht sides together, join 2 two Strap with Tabs.Bringsecond
The ends Strap
of Strap
remaining Tab. Tab
37½” Set together
strips will beInsert a selvage strip at least 48"
ly (figure 1).
parallelogram, cutends of cone
tabs of thread, or a pieces
Creative and
Grids use
circle as follows:
ruler), round
er
by aligning the strips withthe right 2¼” - 2½” usedaside. for the (seam Straps.on Set inside),
those matching
aside. raw figure 5
either together,
2¼” or 2½” the bottom corners of the long3” xinside7” Front theFlap folded (quilted
piece and catch the end in a seam
sightbutsides
2½” might be sew
easier to two 5.
2¼” - 2½” Prepare
4. Assemble Front the Flap.
Strap edges,Tabs. making a tab about 1” x 2¼”.
ther, as shown, offsetting the
!s
).4).
PressStitch
rulerseam the strips
along open. together 2¼” - 2½”
b.a.
a.OnUsing
Withthe seama 2½”
wrong circular
side
sideto down, object
ofsecure
the insert (suchone end of a the 4½”seam,A, a
m
seam allowance
long bias press the interfaced Frontinto Flapthe Facing, a 1” rectangle ring.
the resulting 2¼” figure
- 2½” 3 b. Repeat selvage
with strip
second to
Strapmake Tab. easy Set work of turning the tube right
evenby aligning thethe
with (figure strips with right
strip. the bottom endscorners
gram,
edge
cut
Bring
mark a horizontal of Strap lineofTab thetogether
1½” 3” x 7” Front Flap (quilted
down 1½”
ether, 3). asI shown,
prefer offsetting the fabric)
(seam and 3” tabs
x 7” aside.
Front sideFlap out. Cut
Facing off top
(lining end
fabric).along with selvage strip.
¼”
ong sides together, fold the strip in half
or2¼” 2½” 2¼” - 2½” from the on topinside),
(straight) matching
edge (figure raw figure 5
eand4). Stitch strips
• the strips
but
With 2½” together
right
pin every 4” to 6” to join. Do not might sides be easier
together, to
press. join ends of the
edges,
strips
b.
6). 5.
On the
Mark Prepare
making
wronglines
vertical •
Front
aside
tab3” Fasten
Flap.
about
of a
the 1” x 2¼”. 3”
from large safety pin 3” to one end of a 41½" piece of
2¼” - 2½”
!s
igning
seam work allowance
with.not and press you the seams open. figure 4 1"-wide strapping figure
and 6pull into strap, allowing fabric
st pinning and by pressing,
aligning the will
strips get awith right sides Stitch
interfaced
each side
together, across Front
froma.the bottomFlap
Using of tab
Facing, ⅛” from
a 2½” circular object (such as Template A, a
just-marked
ea
ng 2¼” - 2½”
even with the strip.
m
binding.
s d. With right sides
2¼” -together,
offsetting 2½”the tips join (figure
ends of 4). Stitch the strips edgeatohorizontal
mark
horizontal secure
line cone to the(figure
line
ofbottom5).extend
1½”
to
thread, down
oforthe ½" beyond
facing
a Creative (figure Fold
Grids strapping
6).
circle ruler), on oneround end and to be
"
1½”
rong sides
the strips together,
by 2¼”fold
aligning - 2½” the
the stripstrips inwithhalf right c.from
b. the and
Repeat topwith (straight)
thesecond
bottom edgecorners
Strap (figure
Tab. ofthe thethe
Set 3”sew-in
x 7” Front onFlap
the(quilted
ed ureHandle. together with a ¼" seam allowance and press Center
the sew even
the positive with
side of strapping other end. Be careful
e and pin together, every 4” to as6”shown,to join.offsetting
Do not press. 6). Mark vertical lines 3” from 3”Facing 3”
er sides the tabs
magnetic aside.snap fabric)
between and the
to 3” xmarked
keep 7” the
Front lines
seamFlap (figure
allowance 6).(lining fabric). on one side
centered
ustong sides
pinning
tips andseams
together,
(figure not
4). foldopen.
pressing,
Stitch the
the 4” Trim
you x 11”
strips will tabs
get aeven with the strip. each side from the just-marked
together
s but 2½”
andle might be easierintohalf lengthwise
(contrasting Be sure
5. Prepare Front that
Flap. b. On
the dotthe onand back
wrong of
toside
keep snap ofthe theis strapping
up and and fabric from twisting.
binding.
h.press. with a ¼” seamfabric) allowance and press figurethe 4seams open. horizontal
the smooth line to is thedown.
interfaced
side bottom
Front ofFlap
the Facing,
facing (figure 6). figure 6
Open the fabric
Trim tabs even with the strip. and bring each raw a. Using a 2½” circular Remove
object the
(such safety
as Template pin. Smooth
A, a the fabric over the
ded Handle. c. Center and sew
ofmark the positive side ofglue
the sew-in
e
ight middle
sides(following
together, join the pressed
ends of line); press TIP:
cone A swish
of thread, glueor aafrom horizontal
Creativea washable
strapping, line 1½”
Grids circle
turning downstick
ruler),
the willround
raw edges 1½”
to the inside on the
magnetic snap between theyou marked lines(figure
(figure 6).
s
wrong by e. With together,
sides
aligning wrong
the strips sides fold
withtogether,
theright 4” x fold
11” the strip in half hold
thethe bottom snap from
in
cornersplace the top
the(straight)
ofwhile
end 3”with
x 7” sew. edge
Front
the Flap extending
fabric (quilted beyond
Handle
gether, lengthwise
(contrasting
as shown, and pin
fabric)
offsetting every the4”
in halftolengthwise
6” to join. Do not press. Be sure that6).
fabric)
TIP: Thisand stitching
the dot on
3” x Mark 7”willFrontvertical
be
back of snap
Flap lines
visible Facing
sothe 3” (lining
considerfromis up and
fabric).
the
3” 3” the strapping.
ut again;TIP: center
By just the
pinning1¾”and x 11” not piece
pressing, of Soft you will get a the smooth side
each is Topstitch
down.
side from the just-marked straps along all the edges.
); press. Open the fabric and bring each raw
ere 4). Stitch
® inside.
smoother Fold thefabric
strips
binding.
together
over Soft and Stable thread
b. Onyou the arewrong using. side
• from of
Cut theone 4½" piece from the raw-edge
(figure 6). end of each 42"
he
” middle
seam (following
allowance and the pressed
press the line); press
seams open. TIP: A swish horizontal of glue line a to the
washable bottom glueof the 6facing
stick
figure will
ssed lines. Fold in half again (1” x 11”);
c.interfaced
With wrong sides
Front Flap together,
Facing, align Front Flap on top
ake thewith Padded Handle. hold the snapc.inCenter place strip while
and you
to make
sew sew. two Strap Tabs. The remaining 37½"
s even the strip.
ges with Wonder Clips or pins. Sew all ofmark
prepared Front Flap
a horizontal lineFacing.
1½” down Sew together ⅛” from sew-in
the positive side of the
TIP: This magnetic
stitching will snap
strips
be between
visible will so be the
used
consider markedfor1½”
the the lines (figure
Straps. 6). those aside.
Set
out
e
wrong again;
a.sides
handle, With center
aboutwrong
together,⅛”thesides
from 1¾”the
fold x 11”
together,
the strip
edge; piece fold
in
set ofthe
half Soft 4” x 11” edge.
from the top (straight) edge (figure
sele®and inside.
Padded Fold
pin every Handle fabric over
4” to(contrasting
6” Soft Do
to join. and
fabric)
notStable in half lengthwised.thread
press. 6). Mark you are Be sure
using. that the dot on back 3” of snap 3” is up and
Bind thevertical
side the and lines
smooth
3” from
bottom edges
side is down.
figure 7
essed
sust and (2”lines.
pinning x 11”
Strap Fold
andTabs. in half
); press.
not pressing, againthe
Open (1”fabric
you xwill11”);
getand a bring each raw
ofc.each
With
the wrong
side
Front from sides
Flap/Facing the together,
(figurealign
just-marked 7). Front Flap on top
dges with to
edge
r binding. Wonderthe middle Clips(following
or pins. Sew the all pressed line); press Doof prepared
horizontal
NOT bindline Front
TIP:
upper A
to theFlapswish Facing.
bottom
straight of Sew
ofedge;
glue thefrom together
facing a washable
(figure⅛” from 6).glue stick will
he ht handle,
sides
again. together,
about ⅛”fold from each the 2¾”edge; x 42” set edge. hold the snap in place while you sew.
ded Handle. setc. aside.
Center and sew the positive side of the sew-in
b.ByAnnie.com
Opentogether, out again; center the 1¾”reserved
x 11” piece of SoftAUd. Bind thesnap
magnetic sideTIP: andThis
between stitching
bottom theedges will belines
marked visible figure
(figureso7consider
6).3 the
wrong | © sides LLC 2016 fold the
| All 4” x 11”
rights | 082316
ps andand Strap
Stable Tabs.
® inside. Fold fabric over Soft and Stable of
Be thesure Front that thread
Flap/Facing
the dot you on are
(figure
back using. 7). snap is up and
of
Handle (contrasting fabric) in half lengthwise
edge;together,CONTINUED ON NEXT PAGE 6
© Craftsy
alongOpen pressed Do
theNOT bindc. upper
With isstraight
wrong
down.sides align Front Flap on top
ght sides
); press. together, the lines.
fold
fabric Fold
each and2¾” in half
bring x 42” againraw
each (1” x 11”); smooth
side
secure(following
edges with Wonder Clips orpresspins. Sew all set
TIP: aside.
A swishofofprepared glue fromFront Flap Facing.
a washable glue stick Sewwill together ⅛” from
the middle the pressed line);
k | around © ByAnnie.com the handle, LLC 2016 about | ⅛” All from the edge;| set082316 AU
rights reserved hold the snap edge.
in place while you sew. 3
asten
om the a resulting
large the short edgestitchedfigure
at the 3top.
ping and pull When you’ve the Bring ends of Strap Tab together
ty pin to one
llelogram, cutend When
long you’ve
side and stitched
pressed the
strap, trimming 2¼” - 2½” (seam on inside), matching raw figure 5
er 41½”2¼” or piece2½”of 1” long
the seam,side and pullpressed
on the end
even with the 2¼” - 2½” edges, making a tab about 1” x 2¼”.
!s
pping
s, aligningand pull the
of the seam, pull on
selvage strip to the end
c. Be careful to Stitch across bottom of tab ⅛” from
ea
alongallowing
strap, 2¼”of - 2½”
the selvage strip
make easy work of to
m
the seam 2¼” - 2½” edge toSEWsecure (figure 5).
STURDY: THE ESSENTIAL BACKPACK Fold with Annie Unrein
"
bias
c to extend ½” make
turning easy
the worktube of right-
ance
e (figure centered 2¼” - 2½” b. Repeat with second Strap Tab. Set
ond strapping on turning the tube
side out. Cut off top end right-
ne side and to
prefer tabs aside.
end and to be side
along out.with Cut off top strip.
selvage end
the strapping
but 2½” might bealong easier to selvage strip.
nstripswith the with 5. Prepare Front Flap.
abric
kpping with.from figure 4
on the
ng. Smooth the
rith
end.
rightBe careful to keep
sides together, join ends of the seam allowance Bindings, Handles,
a. UsingStraps, Strap
a 2½” circular Tabs
object (such& asFlap
Template A, a
cone of thread, or a Creative Grids circle ruler), round
c over the
ered on
strips one sidethe andstripsto keep the strapping and
ping. by aligning
Remove the safety withand
pin right topstitch the the bottom corners of the 3” x 7” Front Flap (quilted
ssc together,
from twisting. as Remove
shown,
along the edges. Set aside.
the safety
offsetting the pin. Smooth fabric) and 3” x 7” Front Flap Facing (lining fabric).
abric over the strapping,
the stripsturning the raw edges to
(figure
omnside
a ¼” each
seam
D.allowance
4). Stitch
on 42”
the Assemble
strip,
end cut and
with onefabric
the 4½”the
together
press piece Strap
extending
the seamsto make Tabs
open.
b. On the wrong • sideCenterof thethe positive side of the sew-in magnetic
figure 6
Strap
ond Tabs.
the The
strapping. remaining
Topstitch 37½”
the strips
straps will
along be all interfaced Front Flap snap Facing,
between the marked lines, being sure that
tabs even • withWith the strip.
seam side down, insert one end of a 4½" Strap mark a horizontal the line 1½” downon the back of
for the Straps. Set those aside.
edges. the dot 1½”the snap is up and the
ith wrong sides Tab into the
together, fold opening
the stripof in ahalf1" rectangle ring. Bring ends
from the top (straight) edge (figure
the Strap
om theand Tabs.
raw-edge end4”ofTab
smooth side is down. Use a swish of glue from a
thwise pinof every
Strap toeach to 42”
join.strip,
6”together Do(withnotcutpress.
one 6). Mark vertical lines 3” from
seam on inside), matching 3” 3”
th
Byseam
piece side down,
justtopinning
make two
and insert
Strap
not one
Tabs.
pressing, end
(The
you of a 4½”
remaining
will get a washable
each side from the just-marked glue stick to hold the snap in place, if
raw edges, making a tab about 1" x 2¼". Stitch across
pother
” Tab
strips into
willthe
binding. beopening
used for ofthea 1” rectangle
Straps. Set ring.
those horizontal line to desired.
the bottom Sew
of (figure
the facing 6).
(figure 6).
bottom of tab ⅛" from edge to secure (figure 5).
e.)
Paddedends ofHandle.
Strap Tab together c. Center and sewNote: This stitching
the positive side ofwill
thebe visible on the underside of the flap.
sew-in
m on inside), matching raw figure 5 magnetic snap • With
between wrong
the sides
marked together,
lines (figure align Front Flap on
6).
With s,the Strapsides
wrong
making aTabs. together,
tab about 1” xfold 2¼”. the 4” x 11”
ded Handle (contrasting fabric) in half lengthwise Be sure that the dot top on of prepared
back of snap Frontis upFlap andFacing. Stitch together,
h across
With seambottom side down, of tabinsert⅛” from one figure 5 the smooth side sewing is down.⅛" from edge.
of 11”
to ); press.
asecure
4½” Open
(figure
Strap Tab the fabric
5).into the and bringFold each raw
e to the
ning amiddle
ofwith 1”second (following
rectangle ring. the
Bringpressed line); press TIP: A swish • Using
of glue fromaa2½"washable
circularglueobject
stick will
(such as Template A on
epeat
n. Strap Tab. Set hold the snap in place while you sew.
saside.
of Strap Tab together (seam on Fold page 17, a thread cone, or a circle ruler, round the
de),penmatching • raw
out again; Repeat
center
edges, with
the 1¾”
makingsecond
x 11” a pieceStrap of Tab.
Soft Set Strap Tabs aside.
TIP: This stitchingbottomwill be visible
cornersso consider
of the flap. the
ont Flap. thread you are using.
Stable1”
about ®x inside. Fold fabric
2¼”. Stitch across overbottomSoft of and tab Stable
⅛” • Using the 2" strip of bias binding, bind the side and
ging a 2½”
pressed
edge circular
lines. (figure
to secure object
Fold in 5). (such
half again as Template
(1” x 11”); A, a
c. With wrong sides together, alignofFront
the Flap onFlap/Facing;
top
ure of thread,
edges with
E. Prepare
or aWonder
CreativeClips Front
Gridsorcircle Flap
pins.ruler),
Sew all round
bottom edges
of prepared Front Flap Facing. Sew together ⅛” from
Front do not bind
epeat
ottom with
corners secondof theStrap3” x Tab.
7” Set Flap
Front tabs (quilted
aside. upper straight edge (figure 7). Set flap aside.
nd the handle, • On aboutthe ⅛” wrong from sidethe edge; of the setinterfaced Front Flap edge.
c)
e. andFlap.
ront 3” x 7” Front Flap Facing (lining fabric). d. Bind the side and bottom edges figure 7
Facing, mark a horizontal line 1½" down from the
nStrapsthe wrong and sideStrap ofTabs.
straight the top edge, then mark vertical lines 2⅞" from of the Front Flap/Facing (figure 7).
n the wrong side of the interfaced Front
figure 6 Flap
aced Front Flap Facing,
Withng, right
marksidesa horizontal
together,
each line
side fold1½”
fromeachdown
the 2¾” from x 42”
just-marked the top horizontal lineDo to NOT bind upper straight edge;
a horizontal line 1½” down 1½” set aside.
ight) edge (figure theedge 6).
bottomMark vertical
of the facing lines 2⅞” from 6).
(figure
the top (straight) (figure
hckpackside from| ©the just-marked
ByAnnie.com LLC 2016 | All rights reserved | 082316 AU 3
ark vertical lines 3” from 3” 3”
zontal line to the bottom of the figure 6
side from the just-marked
ng (figure 6).
ontal line to the bottom of the facing (figure 1½”6).
enter
nter and andsew sewthe thepositive
positiveside sideof the sew-in
e sew-in 2⅞” 2⅞”
netic snapmagnetic
betweensnap the marked lines (figure 6).
ween the marked lines
ure that the dot on back of snap is up and(figure
Be
smooth sure sidethat the dot on back of snap is up and
is down.
smooth side is down.
A swish of glue from a washable glue stick will
theA swish
snap of in glue
placefrom while a washable
you sew. glue stick will
the snap in place
This stitching will be visible while youso sew.consider the
dThis
youstitching
are using. will be visible on the underside of
inished
th wrongflap sidesso keep
together, that align
in mind Front when Flap choosing
on top
ad.
epared Front Flap Facing. Sew together ⅛” from
.ith wrong sides together, align Front Flap on top
nd epared
the side Front and Flap Facing.
bottom edges Sew together figure ⅛”7 from
e.Front Flap/Facing (figure 7).
e
OT bind
sing a 2½” upper straight
circular object edge;(such as Template A, a
side.
3
3
© Craftsy 7
b. Topstitch about ¼” from fold on ! Folded edge " i. With WRON
each pocket (figure 8). Set aside. together, align
longer) zipper
2. Prepare Pocket D (inner slip pocket, bottom edge o
contrasting fabric) figure 9 on left side an
SEW
a. With right STURDY:
sides out, foldTHE
the ESSENTIAL BACKPACK
! Folded edge " with Annie Unrein
each end
interfaced 11” x 10½” Pocket D ii. Attach the z
(contrasting fabric) in half lengthwise ¼” from the ed
(5½” x 10½”); press. outside of the
Pockets
b. Topstitch about ¼” from fold at top
of pocket (figure 9). Set aside.
of the zipper ta
the pocket as
3. Prepare Pocket E (front slip pocket, quilted fabric). b. Attach the zippe
(mesh fabric). With
a. On the main fabric side of the 9¾” x 10½” Pocket
A. Pockets A, B & C • With the dot down and the smooth side up, center
E (quilted fabric), mark horizontal lines 1” and 2”
other edge of the z
andedge
sewofthe negative side of the sew-in magneticthe top 11” side of
down
• Pockets A, B and C are the credit card slip pockets from the top 10½” the
figure 10 Be sure that Pocke
in contrasting and lining fabrics. flap (figure 10). Mark snap between
1” vertical lines the marked lines (figure 10).
aligned evenly with
4¾” in from each• sideWith between
rightthe 1”
sides together, align 2” the 2½" x 10½"
• With right sides out, fold each interfaced pocket
two
in (zipper will extend
POCKETShalf lengthwise (to measure 2" x 10½" for A and 12).marked lines.
Set pocket aside.
Pocket E Facing (main figure 12fabric) with Pocket E, placing
fabric on each side
B, 4¾” 4¾”
kets A, B, andandC (credit b. With
5. Prepare the G
Pocket dot(inner
downzippered
and the
one long raw edge of facing below the horizontal zipper to strip. Fing
2¼" x card
10½" slip pockets,
for C). Press.
d lining fabrics). pocket, smooth
mesh side up, center
fabric). and
line sewyou
that the marked 2" from the pocket top. zipperStitchtape to outs
• Topstitch folded edge of each pocket about ¼" from side of the sew-in magnetic
negative
a. Attach a zipper to facing
the to pocket. Press facing up. Sew acrosspocket top ofand sew alo
right sides out, fold(figure
fold each interfaced pocket in
8). Set aside. snap between the marked lines edge of zipper tape
ngthwise (2” x 10½” for A and bottom 11” edge of the 2” x ⅛" from the edge to secure (figure 11).
facing
(figure 10). (figure 13). Set poc
x 10½” for C); press. figure 8 11” Pocket G1 (mesh fabric).
b. Sew a facing on the pocket to figure 11
f thread,
stitch about or a ¼”Creative
from fold Grids
on circle!ruler),
Folded round
edge "
Pocket
cover i.the
With
F2. WRONG
Be sure
magnet and sides
that Pocket
prolong F1 is aligned evenly
wear.
POCKETS
tom corners
ocket (figure of 8).theSetflap. aside. 12). Set pocket
together, aside.
align a 12”
With right sides together, align the beyond fabric on
with Pocket F2 (zipper will (orextend figure 12
LESSON 4. PREPAR
5. Prepare each
2½” Pocketlonger)
side).
x 10½” zipper
Stitch
(innerzipper
GPocket on the
zippered
E Facing 11”
to (main
kets
ngketthe DA,(inner
2”B,stripandslip
ofCbias(credit
pocket, card slip pockets,
binding, figure 7
strip.bottom edge ofthe Pocket
figure 12 AND ZIPPER STRIP
d elining
bric) side and fabrics).
bottom edges of the pocket, mesh
fabric) Finger-press
fabric).
with one long raw edgeG1.
zipper belowPosition zipper pull
figure 9 on
tapemarked
line to left
the side lining
2” from and
side allow
of the ends of zipper to extend on 1. Adjust the shape of the
Flap/Facing
right
rightsidessides B. Pocket
(figure
out,
out, fold7).
fold each
theDoD NOT
interfaced pocket in " a. Attach
pocket each aend
and zipper
sewpress to the
along the top.
very up;
Stitch
3¾” wide at each end.
pper straight ! Folded edge facing to pocket; facing
gthwise
ced 11” x(2”10½”x edge;
10½”Pocket set Aaside.
for Dand bottom
edge of11” tape.edge of the 2” x
sew ii. Attach
across topthe of zipper
facing to the
⅛” frompocket piece, sewing a. On main fabric s
xsting
10½”fabric) for• C);inPocket
press.
half lengthwiseD is the inner figure slip pocket
8 in contrasting 11” fabric.
Pocket G1 (mesh fabric).
• edge
c.Pocket
Bind ¼” fromtop
to secure
the the(figure
10½”edge. edgeFinger-press
11). of the zipper to the 21” x 5” Side Strip
POCKETS
10½”);
titch about press. With
¼” from fold on
right sides out, fold the
! Folded edge "
interfaced 11" x 10½"
Pocket i.outside
WithF1 WRONG
of
using the the sides
pocket;
2” x 10½”sew along the very edge (quilted fabric), ma
to measure 5½" x 10½". c. Bind the top 10½”
• tape, edge (orofthePocket xE using the 2”Ex Binding (contrasting
ocket
kets A,
stitch (figure
about B, and 8).Dfrom
¼”
in half
Set aside.
C (credit
lengthwise
fold atcard top slip pockets,
Press.
Pocket together,
of the zipper
F Binding align a Using
12”
(contrastingflattening 2"the 10½"
zipperPocket against vertical lines 5½” in
10½” Pocket E Binding (contrasting fabric). Set
d lining
ket
ket (figure
D (inner
• 9). Set
fabrics). aside. ¼" from folded edge (figure 9). Set aside.
Topstitch
slip pocket,
aside.
fabric)longer)
the(figure
pocket zipper as on
12). you
Set the
fabric),
go. 11” bind the top 10½" edge of Pocket E. Set
pocket aside.
each end (figure 14
aside. bottom edge of Pocket G1. Position zipper pull
hric)
right sides out, fold
ket E (front slip pocket, quilted fabric). each interfaced pocket
figure 9 in b. Attach
on leftFside the zipper to
andzippered the
allow ends 10½” x 11”
of zipper Pocket
to extendG2 on b. Make a mark ⅝”
4. Prepare Pocket (back pocket, quilted fabric).
ngthwise
right
he
x
main
10½”
sides (2”out,
fabric
for
x 10½”
C);
fold of
side
press.
for A and
the the 9¾” x 10½” figure
Pocket
! Folded edge " 8 5. Prepare
(mesh
a.
other
Pocket
each
Attach
fabric).
edge
G (inner
end
a zipper
of
With
the
D. to
Pocket
zipper
zippered
wrong
the bottom
sides
along
F
pocket,
together, mesh
10½” edge of the
alignfabric).
the the strip. Align a ru
ed
ed 11” x 10½”
fabric), mark Pocket
horizontal D lines 1”and 2” edge a. Attach a zipper to thetobottom 11” edge figureof sewing
the
13 2” x of these marks with
Folded 1½”
the ii.
x Attach
top 10½”
11” side the• of
Pocket zipperF1
Pocket the
(quilted
Pocket G2.Fpocket the piece,
fabric).
is back zippered pocket, made with same side/end. Ma
stitch
sting about
fabric) ¼”
in
rom the top 10½” edge of the from
half fold
lengthwise on 11” Pocket
¼” from G1the (mesh
edge. fabric).
Finger-press the zipper to the F2 (quilted fabric).
10½”);
ocket10). press.
(figure figure 10 Be
sure
i. With thatRIGHTPocket sidesG1
pieces is Pocket
together, alignF1 and
a 12” Pocket
(or inside marked lines
gure Mark8).1”Set aside.
vertical lines of the pocket;sidessew
1”
outside
aligned i. With
longer) evenly WRONG
zipper with
• on Pocket
the
With 10½”G2 along
together,
RIGHT bottom
sides
the very
align
edge
a 12”
of
together,
edge(or
align a 12" or along marked lines
longer
fromDabout
ket
titch each
(inner side
¼”slip between
from fold atthe
pocket, top oflonger)
the
2” (zipper Pocket willzipper zipper
extend
F1.
tape,
Allow
on the
beyond flattening
ends
11” bottom
of
the zipper
zipper to
edge against
extend
of Pocket
on
arked
bric) lines.
et (figure 9). Set aside. figure 9 the
G1. pocket
Position as zipper zipper
youStitch on the 10½"
go.pull on left side and allow bottom edge of Pocket F1. Allow
4¾” 4¾” fabric each on each
end. side).ends
h the
right dot sidesdown out, and fold the the zipper
b. Attachendsto of
strip.
the zipper to
Finger-press
zipper to extend
the
of zipper
10½” onxeach toend
11” Pocket
extend G2
on each end.
ket E (front slip pocket, quilted fabric). Folded edge
hced side up, center
11” x 10½” Pocket D and sew the
zipper
(mesh
ii. Attach
ii.fabric).tape
Attach
the
toWith • zipper
outside
the Stitch
wrong
zipper
to the
of tosides pocket
zipper to
together,
the pocket
piece,
pocket
piece,
sewing
alignsewingpiece,
the sewing ¼" from the Cut away fa
he main fabric
of C. side of the 9¾” x 10½” Pocket ⅝”R
ve sidefabric)
asting
ed fabric), mark
Pocket
theinsew-in
half magnetic
horizontal
Elines 1” and 2” pocket
other
¼”
edge
¼”
lining
from
and
from
side
the
ofsew
of
edge.
the alongzipper
edge.
the
Finger-press
edge.
very
along Finger-press
Finger-press
pocket; sew
the
along
the
zipper
zipper
the
figure very
13
to
the zipper the
to the tape to the lining side
etween
wise (5½” thex marked
10½”); press. lines edge
the top of11”
outside zipper
side of tapeof Pocket
the to
ofsecure
pocket; theG2. sew
pocket,alongas theshownvery edge in the class. Sew along
om
10).the top • 10½” Pocketedge Eofis thethe frontfigure
slip10 pocket in quilted fabric.(figure
Be
edge
sure of 13). of Set
thatzipper
the
the pocket
Pocket
zipper tape,
tape,G1 aside.
is
flattening
flattening the zipper
the zipper against
stitch about
ure 10). Mark ¼” 1”from
verticalfold at
linesfabric side of the 9¾" x 10½" Pocket against the
the pocket as you go. edge of the zipper tape, flattening the zipper
a facing •
on theOnpocket
the main to figure 11 aligned Etheevenly pocket withas Pocket
you go. G2 the pocket as you go.
pocket (figure
rom each sidepiece, 9). Set
between aside. 1”
the horizontal lines2”¾" and 2" from against ⅝”R
mark topb. Attach
10½"willthe zipperbeyond to the 9” x 10½” Pocket F2
he magnet
rked
ket Elines.
and prolong wear.
(front slip pocket, quilted fabric). (zipper
b. Attach extend
the zipper
• right to
Withthe RIGHT 11” x 11” Pocket
sides G2 (mesh
together, align the other edge of Cut away fa
ght sides together, edge.align Mark the1" vertical4¾” lines 4¾” 4⅝" in fromLESSON (quilted
fabric
each sidefabric).4. PREPARING
on fabric).
each With
side).
With wrong sides Stitch
thealong
THE along
sides
zipper
SIDEthe
together, STRIP
align the
top of 10½" side of Pocket F2. Be
the
he main
10½” dot down
Pocket fabric Eand
sidethe
Facing of the(main 9¾” x 10½” Pocket other 10).
zipper edge
to strip. of the zipper
Finger-press the top 10½” side
side
ted up, center
between
and sew
the
the
two marked AND
horizontal lines ZIPPER
(figure
together,
Pocket F2. STRIPS.
align
Be
the
sure
other
sure
that
edge
that
Pocket Pocket
F1 is aligned
figure
F1 is
13
aligned
evenly evenly 2.
with Pocket
Prepare Zipper Strips.
withfabric),
one long mark rawhorizontal
edge below lines ¾” and 2” zipper
ofthe tape
theshapezipper to along
outside theoftop 11” tapering the sides to
eromside the of the
top sew-in
10½”
arked 2” from the top. Stitch edgemagnetic
of the 1. Adjust with
pocket Pocket
and F2
sew of the
(zipper
along Side
F2 will
very Strip,
extend
(zipper beyond
will extend fabric on
beyond fabric on each side).
figure 10 side of Pocket G2. Be sure a. Attach the zipp
etween
gure 10).
to pocket; theMark marked
press 1”facing linesup;
vertical 3¾” wide each
edge at eachside).
of zipperend.
Stitch tape zipper
toStitch
secureto strip.
zipper; Finger-press
finger-press the the zipper tape to24” the(or longer) dou
10). ¾” that Pocket G1 is aligned
⅝” in top
from ofeach side⅛” between 2” zipper
(figure to
13). thefabric
lining side of the pocket andpocketsew along
ross facing from a. On main
evenly withSet Pocket pocket side
G2 aside.
of
lining
(zipper side of the figure 14 and sew along edgedown of on main fabr
ooamarked
secure
facing on lines.
(figure 11). to
the pocket 4⅝”figure 11 4⅝” edge.
21” x 5” Side Strip Strips (quilted fabr
will extend beyond fabric zipper ontape as in previous step.
hethe magnet and and prolong wear. E using the 2” x c.(quilted
Bindside).the fabric),
top mark
10½” edge 5½” F1 using the5½”
h the dot
top down 10½” edge theof Pocket each Stitch • zipperUsing toofthe
Pocket 2" x 10½" Pocket2”FxBinding (contrasting tape along the long
hhtside
Pocket sides E together,
up, align
center (contrasting
Binding and sewthethe fabric). Set LESSON vertical
10½”
strip. 4.Pocket
PREPARING
lines F5½”
Finger-press inzipper
Binding from THE
(contrasting
tape SIDEfabric) STRIP(figure tape extend on eac
0½”
ve sidePocketof theEsew-in Facing (main AND each
ZIPPER
to outside endSTRIPS.(figure
of pocket 14).fabric),
and sew
bind the top 10½" edge of Pocket F1 (figure
with one long
tic snap between raw edge the markedbelow The Essential Backpack | © ByAnnie.com
along very edge⅝”
12). Set
of zipper
LLCpocket
tape
2016 | aside. All rights reserved | 082316 AU
ket F (back zippered pocket, quilted fabric).
b.
1. Adjust the Makeshape a markof the Side in from Strip, each side onthe
tapering each end to
sides of
rked 2”
igure 10). from the top. Stitch to secure (figure 13). Set
o pocket; pressthe facing up;10½” edge of the 3¾” widethe strip. end.
at each Align a ruler with its edge connecting each
chaa zipper
facing ontothe bottom
pocket to pocket
of these aside.
marks with the line marked 5½” from the
oss top of facing ⅛” fromfabric). figure 11 a.same On main fabricMark side along of
10½”
he magnet Pocket and F1prolong
(quilted wear. side/end. edge of ruler. figure Stitch
14 1/8”
secure (figure 11). 21”
inside x 5”marked
Side Strip lines to seal edges; cut fabric away
ght sides
With RIGHT together, align the align a 12” (or
sides together, 5½”
the top 10½”on LESSON (quilted fabric),
4.marked
PREPARING mark(figure THE 15). SIDE STRIP 5½”
10½”
nger) Pocket
zipper Eedge
Facing
the 10½” of Pocket
(main
bottom E using
edge the of 2” x along lines
ocket E Binding (contrasting fabric). Set vertical lines 5½” in from
with one
ocket F1. Allowlong raw ends edge belowto extend on
of zipper AND ZIPPER STRIPS.
each end (figure 14).figure 15
arked
ch end. 2” from the top. Stitch
to pocket; 1. Adjust the
b. MakeCut shapea mark of the
⅝”fabricSide
in from Strip,
eachtapering
side on the sides
each end ofto
ket
AttachF (back the press zippered
zipper facing
to the up;
pocket,
pocketquilted fabric).
piece, sewing 3¾” wide atstrip.
eachAlign away
end. outside these lines.
cross top of facing ⅛” from ⅝”R the a ruler with its edge connecting each
”hfrom
a zipper the ©edge.to Finger-press
the11). bottom 10½”the edgezipper
of the to the CONTINUED ON NEXT PAGE 8
oingsecure (figure
Craftsy
ofa.these
On main marks fabric withside the of line marked 5½” from
figure 14 the
10½”side Pocket of the F1pocket;
(quiltedsew along the very
fabric).
theoftop same
21” x side/end.
5” Side Mark
Strip along edge of ruler. Stitch 1/8”
ge the10½” zipper edge tape, of flattening
Pocket E the using the 2” x
zipper 5½” cut fabric away5½”
With RIGHT sidesas together, inside
(quilted markedfabric), linesmark to seal edges;
Pocket
ainst E Binding
the pocket you go.align
(contrasting a 12”Set
fabric). (or
ger) zipper on the 10½” bottom edge of along
vertical marked
lines 5½” linesin(figure from 15).
SEW STURDY: THE ESSENTIAL BACKPACK with Annie Unrein
N 3. POCKETS 12). Set pocket aside. figure 12
Pockets A, B, and C (credit card slip pockets, 5. Prepare Pocket G (inner zippered
g and lining fabrics). pocket, mesh fabric).
With right sides out, fold each interfaced pocket in a.Pockets
Attach a zipper to the
alf lengthwise (2” x 10½” for A and bottom 11” edge of the 2” x
2¼” x 10½” for C); press. figure 8 11” Pocket G1 (mesh fabric).
Topstitch about ¼” from fold on ! Folded edge " i. With WRONG sides
2). Set
ach pocket
pocket aside.
(figure 8). Set aside. figure 12 the apocket.
together, align 12” (or Sew along the edge of the zipper tape,
Pocket G (inner zippered longer) zipper on the 11”
flattening the zipper against the pocket as you go.
Pocket D (inner slip pocket, bottom• edge of Pocket G1. Position zipper pull
esh fabric).
g fabric)
With WRONG sides together, align the other edge
figure 9 on left sideof
and allow ends of zipper
the zipper along the top to extend on of the 10½" x 11"
11" side
Attach
With a zipper
right sides to out,thefold the each end
! Folded edge " Pocket G2 piece. Be sure that Pocket G1 and Pocket
ottom 11” edge
terfaced 11” x 10½” Pocketof the 2” x D
1” Pocket G1 (mesh fabric). ii. Attach the G2zipper to the pocket
are aligned evenlypiece, sewing
(zipper will extend beyond
ontrasting fabric) in half lengthwise ¼” from themesh
edge. fabric
Finger-press
½”i.xWith10½”); WRONGpress. sides on both sides). to
the zipper the the zipper to
Stitch
outside of the pocket; sew along the very edge
together,
Topstitch align¼”
about a 12”from(orfold at top Pocket
of the zipper G2. Finger-press
tape, flattening the zipperthe zipper tape to the
against
longer)
pocket zipper
(figure 9).on Set the 11”
aside. the pocket outside
as you go. of the pocket and sew along the edge of the
bottom edge of Pocket G1. Position zipper pull zipper tape to secure, as in previous step (figure 13).
Pocket
on leftEside (front
andslip allow pocket,
ends of quilted fabric). b. Attach the zipper to the 10½” x 11” Pocket G2
Oneach
E. Pocket
end
the main
G zipper to extend on
fabric side of the 9¾” x 10½” Pocket
Set wrong
(mesh fabric). With pocketsides
aside.
together, align the
other edge of the zipper along
(quilted
ii. Attach • thePocket
fabric), mark horizontal
zipper Gtois
thethe linespiece,
inner
pocket 1”zippered
andsewing
2” pocket, made from
the top 11” side of Pocket G2.
figure 13
own¼” from
from the thetop 10½”Finger-press
edge.
pieces edge
G1 andofG2 the(mesh
the zipper to
fabric). the
figure 10 Be sure that Pocket G1 is
ap (figure
outside• 10).
of theMark
With 1”
pocket; vertical
WRONG lines the
sew sides
along very edge
together, align a 12" or longer aligned evenly with Pocket G2
¾” inof from each side
the zipper tape,between
flattening the zipper 1” against
wo marked
zipper
lines.
on the 11"the bottom edge 2” 2" x 11" Pocket(zipper
of the G1 will extend beyond
the pocket as you go.
piece. Position the zipper 4¾” pull on the left side andfabric on each side). Stitch
4¾”
With
Attach thethedot downtoand
zipper thethe10½” x 11” Pocket G2 on each end. zipper to strip. Finger-press
moothfabric).
side up,
allow
center
ends
andsides
of zipper
sew together,
the
to extend
mesh With wrong align the zipper tape to outside of
egative • ofStitch
side zipper to the pocket piece, sewing ¼" from
her edge of thethe sew-in
zipper magnetic
along figure
pocket and sew along very
nap
e top between
11” sidethe the edge. lines
of marked
Pocket Finger-press
G2. the13zipper to the outside ofedge of zipper tape to secure
egure
sure10).that Pocket G1 is (figure 13). Set pocket aside.
igned
Sew aevenly
facingwith on thePocketpocket G2to figure 11
ipperthe
over willmagnet
extendand beyond prolong wear.
bric on each
ith right sidesside). Stitchalign the
together, LESSON 4. PREPARING THE SIDE STRIP
pper
½” to strip.
x 10½” Finger-press
Pocket E Facing (main
pper
AND ZIPPER STRIPS.
bric) tape
with oneto outside
long raw of edge below
ocket
ne and sew
marked 2” fromalong theverytop. Stitch 1. Adjust the shape of the Side Strip, tapering the sides to
dge
cingoftozipper
pocket; tapepressto secure
facing up; 3¾” wide at each end.
gure
ew 13). Set
across top pocket
of facing aside.
⅛” from a. On main fabric side of figure 14
dge to secure (figure 11). 21” x 5” Side Strip
(quilted fabric), mark 5½” 5½”
Bind the top 10½” edge of Pocket E using the 2” x
N 4. PREPARING THE
0½” Pocket E Binding (contrasting fabric). Set SIDE STRIP vertical lines 5½” in from
PPER
side. STRIPS. each end (figure 14).
he shape
Pocket F of the zippered
(back Side Strip, tapering
pocket, the sides
quilted to
fabric).
b. Make a mark ⅝” in from each side on each end of
at each end. the strip. Align a ruler with its edge connecting each
Attach a zipper to the bottom 10½” edge of the of these marks with the line marked 5½” from the
½” Onxmain
10½”fabric Pocket sideF1of (quilted fabric).figure 14 same side/end. Mark along edge of ruler. Stitch 1/8”
1” x 5” Side Strip inside marked lines to seal edges; cut fabric away
i. With RIGHT sides together, 5½” align a 12” (or
uilted fabric), mark 5½” along marked lines (figure 15).
longer) zipper on the 10½” bottom edge of
ertical lines 5½” in from
Pocket F1. Allow ends of zipper to extend on
ach end (figure 14). figure 15
each end.
Make a mark ⅝” in from each side on each end of Cut away fabric outside these lines.
ii. Attach the zipper to the pocket piece, sewing
e strip. Align a ruler with its edge connecting each ⅝”R
¼” from the edge. Finger-press the zipper to the
these marks with the line marked 5½” from the
lining side of the pocket; sew along the very
ame side/end. Mark along edge of ruler. Stitch 1/8”
edge of the zipper tape, flattening the zipper
side marked lines to seal edges; cut fabric away
against the pocket as you go.
ong marked lines (figure 15).
Attach the zipper to the 9” x 10½” Pocket F2 ⅝”R
Cut away fabric outside these lines.
uilted fabric). Withfigure right 15 sides together, align the
her edge of the zipper along the top 10½” side of
Cut away fabric outside these lines.
ocket F2. Be sure that Pocket F1 is aligned evenly 2. Prepare Zipper Strips.
th Pocket F2 (zipper will extend beyond fabric on a. Attach the zipper to the Zipper Strips. Align a
ach side). Stitch zipper to strip. Finger-press the 24” (or longer) double-slide handbag zipper face
pper to the lining side of the pocket and sew along down on main fabric side of one of the 21” x 2” Zipper
dge. Strips (quilted fabric) with the long edge of the zipper
Bind Cut
the top
away
© 10½”
Craftsy edge
fabric of Pocket
outside theseF1 using the 2” x
lines. tape along the long edge of the strip. Let the zipper 9
0½” Pocket F Binding (contrasting fabric) (figure tape extend on each end of the strip. Attach the
Zipper Strips.
Backpack | © ByAnnie.com LLC 2016 | All rights reserved | 082316 AU 4
other edge of the zipper along figure 13
the top 11” side of(mesh Pocket fabric).
G2. With wrong sides together, align the
other
Be sure that Pocket G1 is edge of the zipper along figure 13
aligned evenly with thePocket
top 11” G2 side of Pocket G2.
(zipper will extendBe sure that Pocket G1 is
beyond
fabric on each aligned
side). Stitch evenly with Pocket G2
2” SEW STURDY: THE ESSENTIAL BACKPACK with Annie Unrein
zipper to strip. Finger-press extend beyond
(zipper will
¾”
zipper tape to outside fabricofon each side). Stitch
pocket and sew along zipper to strip. Finger-press
very
zipper
edge of zipper tape to secure tape to outside of
(figure 13). Set pocket pocket and sew along very
aside.
edge of zipper tape to secure
Side Strip/Zipper Strips
(figure 13). Set pocket aside.
zipper to the strip, sewing ¼” from the edge. Finger- LESSON 5. B
zipper to the strip, sewing ¼” from the edge. Finger-
ON 4. PREPARING THE SIDE STRIP LESS
ZIPPERLESSONA. Shape Side Strip
STRIPS.4. PREPARING THE SIDE STRIP
press the C. Shape
zipper
press
to thethe
the zipper
inside
along the very edge of the tape. In the same manner,
Zipper
to
of the strip
the inside Strip
and sew
of the strip and sew 1. Prepare Backp
along the very edge of the tape. In the same manner, 1. Prep
st the shape•
AND On
of the main fabric
Side Strip,
ZIPPER side of 21" x 5"
tapering the sides to
STRIPS. Side Strip (quilted fabric), sew the • otherTrim side the of the
Zipper zipper Stripto theto other
3¾" 21”
wide, x 2”
making sure a. Attach
that
sew the other side of the zipper to the other 21” x 2”
de at each end. mark vertical lines 5½" from each end (figure 14). Zipper Strip,the beingfabric careful strip to align
is thethe sameshortwidthends ofon each side of of Backp
1. Adjust the shape of the Side Strip, tapering the sides to the Zipper Strips. Zipper Strip, being careful to align the short ends of
a. On main fabric zipper to the the
the zipper.
strip,
Zipper sewing (Line
Strips. ¼” from a ruler thewith edge.the Finger-1⅞" markingsLESSON along i.5.On B
3¾” widesideat eachof end. figure 14
21” x 5” Side Strip b. Adjust
press the the
zipper
the
b.
shape to the
center
Adjust
ofinside
the ofthe the
shape
Zipper the Strip.
ofzipper
of the
strip and and
teeth
Zipper
sew trim one side;
Strip.
12½
a. On main fabric 5½” side of along the very edge ofStrip
the tape. Inwide,
the 1. Prepare Backp
Fron
(quilted fabric), mark 5½” figure 14 i. Trim then
the Zipper trim entire to 3¾”strip to same
3¾"
making manner,
wide.) sure
vertical lines 5½” in 21”fromx 5” Side Strip sew that
the
other i. Trim
side of the Zipper to
zipper Strip
the to 3¾”21”
other wide, x making sure
2” a. Attac
horiz
(quilted fabric), mark 5½” 5½”
• theMark fabricthe striplengthwise
that careful
the fabric
is the samecenter
strip is
width onofeach
the same
the
width
Zipper
on each
Strip by
each end (figure 14). Zipper Strip,
side onmarking being
the zipper. to align the short ends of of Back
the t
vertical lines
on 5½” in from ⅝" from each long the Zipper Strips. side onathe vertical
zipper.line 10½" from either end of the lines
b. Make • a mark Make ⅝” marks
in from each
each end (figure 14).
short
side ends
on each ofend
strip,
of ii. Mark lengthwise
strip (figure center
16). of Zipper Strip by i. On
abov
the strip. Align edge. Align
a ruler withaits ruler
edgewith its edge
connecting connecting each ofb. Adjust
each the ii.
shape Mark of lengthwise
the Zipper center
Strip. of Zipper Strip by 12½
b. marks
Make marking a
of these marks with
these the linea with
mark the
marked ⅝”5½”in
linefrom
from each
the side
marked at 5½"on each
and end
mark of
marking a
i. Trim the Zipper Strip to 3¾” wide,
vertical figure 16 making sure ii.FronW
same side/end. the strip.
Mark along Align
edge aofruler
ruler. with its edge
Stitch 1/8” connecting each vertical figure 16 hori
dow
the lines connecting these points (figure 15). that10½”
line the fabric strip is the same width on each
inside marked of to
lines these marks with
cut the lineaway
marked 5½” from the line 10½” 10½” the
towa
• Stitch same ⅛"seal
insideedges;
side/end. marked
Mark
fabric
lines
along to seal
edge of edges.
ruler. Cut
Stitch 1/8” side
in from on the zipper.
in from
10½”
along marked lines (figure 15). lines
Back
fabric away
inside alonglines
marked markedto seallinesedges;(figure 15). This
cut fabric away either
ii. Mark end lengthwise
either endcenter of Zipper Strip by abo
prep
tapersalong themarked
sides lines
to 3¾" (figure
at each15). end. (figure
marking a (figure
figure 15 16). betw
ii. W
vertical 16). figure 16 with
Cut away fabric outside these lines. figure 15 iii. • Mark
line 10½” a 2” horizontal
Mark a 2" horizontal line ½” line in from ½" the
from topthe top and dow
iii. Mark a 2” 10½” horizontal line ½” in from the top edge
towa
in
and from
bottom
bottom in the lengthwise
of the in strip, center
perpendicular of the Zipper
Cut away fabric outside these lines. and bottom the lengthwise centerto of and centered
the Zipper (figu
Bac
either1”end
Strip ononthe each side of center line (figure 17). raw
⅝”R Stripvertical
1” on each lineside you've just line
of center marked (figure(figure
17). 17). prep
(figure
16). figure 17
figure 17
iii.
betwC
2”
with
with
Cut away fabric outside these lines.
iii. Mark a 2” horizontal line ½” in2” from the top edg
wron
⅝”R and bottom in the lengthwise center of the Zipper (figu3
the
Cut away fabric outside these lines. Strip 1” on each side of !2”" center line (figure 17). raw
(mai
!2”"
are Zipper Strips. leng
iv. Mark figure 17
a line connecting one end of this line iii. C
a. Attach 2. the zipper
Prepare to theStrips.
Zipper Zipper Strips. Align a iv. Mark a line connecting one end of this line Align
with
B. Attach
24” (or longer) double-slide Zipper handbag tozipper
Zipper face Strips with the
• Mark corresponding
with lines end
connecting each
2”
the corresponding
of the zipper
end of endstrip.
theof eachstrip.
zipper 2" line with Faci
wro
down on main a. Attach
fabric side of one the zipper
of the 21” to the
x 2”Zipper
Zipper Strips. Align a Repeatthe on each side of line on
corresponding end topofand the bottom.(figure 18). alon
• Right sides together, align a 24" or longer double- Repeat on each side of line onstrip
top and bottom. the
Strips (quilted fabric) 24” with
(or longer)
the long double-slide
edge of thehandbag zipper zipper face Stitch 1/8” inside each !2”" marked line to seal acro
• Move
edges;
Stitch
carefully
both 1/8”
cut
insidepulls
zipper
away
each to
fabric
marked
outside
theof line to seal
center
lines
of the Zipper (ma
slide down
handbag on main fabric
zipper
tape along the long edge of the strip. Let the zipper side
with of
theone of
main the 21”
fabric x 2” Zipper
side of ¼” s
Strip. edges;Stitch carefully
⅛" inside cut away each fabric
marked outside line ofand
linesacross leng
tape extend on one Strips
of the
each end(quilted
21" fabric)
x 2"strip.
of the Zipper with
Attach the
thelong
Strips edge offabric),
(quilted with to
the zipper iv.make
Mark aa to linemake connecting a one figure
end of18this line turn
Alig
tape alongedge the longzipper
edge oftape the strip. Let thelong
zipper Zipper ends to seal edges. Carefully cut away fabric raw
the long of the along the edge with the corresponding
Zipper end of the zipper strip. figure 18 Fac
tape extend on each end of the strip. 4 Attach the Strip that
outside
Repeat onStrip eachthat of lines so that
side of line on top and bottom. the
2” strip is now tapered in Stitc
of the strip. Let the zipper tape extend on both ends 2” alon
tapers in tocenter,
the as
d | 082316 AU of the strip. Stitch the zipper to the strip, sewing ¼" 4 Stitch 1/8” inside in
tapers each to shown.
marked line Trimtozipper
seal tape even with edge
acro
the middle
edges;fabric. carefully cut away fabric !2”" outside of lines
from the edge. the middle b. Attach
¼” s
(figure
to make 18).
a (figure 18). !2”"
• Finger-press the zipper to the inside of the strip Backpac
turn
v. Move both zipper pulls to center
Zipper figureof18 Zipper
and sew along the edge of the zipper tape. Strip that
Strips.
v. Move both zipper pulls to center of Zipper
Stitch across the zipper tape 2” even with
i.raw Ma
Strips. Stitch across the zipper tape even with Stitcm
the
• In the same manner, sew the other side of the tapers
each end in to
of the Zipper Strips. Trim zipper tape edg
each end of the Zipper Strips. Trim zipper tape Back
zipper to the second 21" x 2" Zipper Strip, being the middle
even with both ends of strips.
even with both ends of!2”" strips. b. Attac
(figu
careful to align the short ends of the Zipper Strips. (figure 18).
Backpac
From here, we'll refer to the two joined strips 3. the
asPrepare v. Move both
Zipper/Side Strip.zipper pulls to center of Zipper
3. Prepare Zipper/Side Strip.
Strips. Stitch across the zipper tape even with i. M
Zipper Strip. a. Join theend SideofStrip to the Zipper Strip. With right the
each
a. Join the
theZipper
Side Strip Strips. to theTrim zipper
Zipper tape With right
Strip.
sideseven together,
with attach the Side Strip to the Zipper Bac
sidesboth ends of
together, strips.
attach the Side Strip to the Zipper
Strip, matching the short ends and sewing across (figu
ii. Al
Strip, matching the short ends and sewing across
those short ends with a ⅜” seam. To help reduce side
those short ends with a ⅜” seam. To help reduce
3. PreparebulkZipper/Side
in the seam, Strip.
sew a couple of extra lines of the B
bulk in the seam, sew a couple of extra lines of
stitching
a. Join the in the
Sideseam
stitching Strip allowance.
in tothethe seam Zipper Strip. With right
allowance. facin
b. Finish
sides the rawattach
together, edge.the With Side right sides
Strip out,Zipper
to the fold each raw
b. Finish the raw edge. With right sides out, fold each botto
Strip,
2” x 4½” matching
Side Strip the Binding
short ends and sewing
(contrasting across
fabric) in half ii. A
2” x 4½” Side Strip Binding (contrasting fabric) in half botto
those short(1”
lengthwise endsx 4½”) withand a ⅜”pin. seam. On theTo help zipper reduce
side of side
lengthwise (1” x 4½”) and pin. On the zipper side of
bulkseam,
the in thealignseam, one sew a couple
binding piece of with
extraitslines rawof edges iii.
theR
the seam, align one binding piece with its raw edges
stitching in
matching the theraw seam edges allowance.
of the seam. Sew across the facin
botto
matching the raw edges of the seam. Sew across the
binding
b. Finish the strip with
raw edge.a ⅜” seam.
Witharight Again, to
sides out, help reduce
foldtoeach raw
binding strip with ⅜” seam. Again, help reduce iv. W
bulk
2” x in
4½” theSide seam,Strip sew a couple
Binding of extra lines
(contrasting fabric) of in half bott
© Craftsy bulk in the seam, sew a couple
CONTINUED of extra
ON lines
NEXT of
PAGE 10 botto
stitching
lengthwise in the(1” seam
x 4½”) allowance.
andseam pin. On the zipper side of bott
stitching in the allowance. long
c. theFold
seam, the align
binding oneflat onto the
binding piece Side
c. Fold the binding flat onto the Side Strip, enclosing with Strip, enclosing
its raw edges iii. R
botto
matching
the raw edge; the rawstitch edgesdownofalong the seam. the folded Sew edge.across the bott
Pres
the raw edge; stitch down along the folded edge.
SEW STURDY: THE ESSENTIAL BACKPACK with Annie Unrein
D. Join Zipper Strip & Side Strip measure 1" x 4½". Pin. On the zipper side of one of
the seams, align one binding piece with its raw
• With RIGHT sides together, attach the shaped Side
edges matching the raw edges of the seam. Sew
Strip to the shaped Zipper Strip, matching short
across the binding strip with a ⅜" seam. Again, to
ends and sewing with a ⅜" seam.
help reduce bulk in the seam, sew a couple of extra
Note: To help reduce bulk in the seam, sew a couple of
lines of stitching in the seam allowance.
extra lines of stitching in the seam allowances.
• Fold the binding flat onto the Side Strip, enclosing
• Using the 2" x 4½" Side Strip Binding pieces
the raw edge; stitch along the folded edge. Repeat
(contrasting fabric), finish the raw edges of the
on the other seam with the second Side Strip
seam allowances as follows: WIth RIGHT sides out,
Binding piece.
fold each Side Strip Binding in half lengthwise to
© Craftsy 11
Adjust
the
ii. Mark shape ofcenter
lengthwise the Zipper Strip.
of Zipper Strip by 12½” xthe
above 10½” Backpack
3” line (figure 19).
marking a
i. Trim the Zipper Strip to 3¾” wide, making sure Front (quilted fabric), mark a
vertical ii. With main
horizontal line fabric
3” down side from figure 20
that the fabric strip is the samefigure width16on each down and the bound edge
line
side10½” on the zipper. the top and mark vertical
10½” toward
lines 1¾” thefromtop of eachtheside
in from
ii. Mark
either end lengthwise center of Zipper Strip by SEW
Backpack
above STURDY:
the Front,
3” line THE ESSENTIAL
center
(figure the
19). BACKPACK with Annie Unrein
marking a
(figure prepared Front Flap
vertical figure 16 ii. With main
between fabric side
the marked lines
figure 20
16). down and the bound edge
line 10½” with flap’s long bottom raw
iii. Mark a 2” horizontal 10½”
in from line ½” in from the top toward
edge the top
above theof3”the line
and bottom
either end in the lengthwise center of the Zipper Backpack Front
Backpack
(figure
prepared
20). Sew &
Front, Back
center the
across the
Strip
(figure 1” on each side of center line (figure 17). raw edge Frontwith an Flap⅛” seam.
16). between the marked lines
figure 17 iii.
with Cover
flap’sraw long edges
bottom of flap
raw
iii. Mark a 2” horizontal2”line ½” in from the top with the Flapthe Facing: With
and bottom A.inAttach the lengthwise Front center Flapof theto Backpack Front wrong
Zipper
edge above
(figure sides20). Sew
3”
together,
line
across foldthe
figure 21
Circle Templates
Template A
Template B
2½” circle
Template A
3½” circle
Template B
2½” circle
3½” circle
The Essential Backpack | © ByAnnie.com LLC 2016 | All rights reserved | 082316 AU 8
The Essential Backpack | © ByAnnie.com LLC 2016 | All rights reserved | 082316 AU 8
© Craftsy 17