Professional Documents
Culture Documents
Release Notes
IndustrialIT
800xA - Device Library Wizard
FOUNDATION Fieldbus, HART, PROFIBUS
Version 5.0 SP1
Release Notes
NOTICE
This document contains information about one or more ABB products and may include a
description of or a reference to one or more standards that may be generally relevant to
the ABB products. The presence of any such description of a standard or reference to a
standard is not a representation that all of the ABB products referenced in this document
support all of the features of the described or referenced standard. In order to determine
the specific features supported by a particular ABB product, the reader should consult the
product specifications for the particular ABB product.
The information in this document is subject to change without notice and should not be
construed as a commitment by ABB. ABB assumes no responsibility for any errors that
may appear in this document.
In no event shall ABB be liable for direct, indirect, special, incidental or consequential
damages of any nature or kind arising from the use of this document, nor shall ABB be
liable for incidental or consequential damages arising from use of any software or hard-
ware described in this document.
This document and parts thereof must not be reproduced or copied without written per-
mission from ABB, and the contents thereof must not be imparted to a third party nor used
for any unauthorized purpose.
The software or hardware described in this document is furnished under a license and
may be used, copied, or disclosed only in accordance with the terms of such license.
This product meets the requirements specified in EMC Directive 89/336/EEC and in Low
Voltage Directive 72/23/EEC.
TRADEMARKS
All rights to copyrights, registered trademarks, and trademarks reside with their respec-
tive owners.
2PAA102574R5011 5
Table of Contents
2PAA102574R5011 6
Section 1 Release Notes
Introduction
This document represents the release notes for the Device Library Wizard, Version
5.0 Service Pack 1 for ABB Industrial IT Systems.
This document provides a brief overview on functionality. It enumerates known
problems encountered in the final testing of this product release. Where possible the
document identifies workarounds that help overcome the problem. The document
contains additional notes that may be valuable to customers and service personnel
working with the product.
Product Description
For easy integration of fieldbus devices into Industrial IT system environments ABB
provides a continuously increasing set of pre-integrated device types for
FOUNDATION Fieldbus, HART and PROFIBUS protocol in the form of device
type files. The Device Library Wizard is a tool that is used for adding these
separately delivered device types to the Device Libraries of an ABB Industrial IT
system.
New Features
Version Description
1.0 First version
1.0 SP1 Service Pack, containing error corrections and support of 800xA
system Version 4.0
2PAA102574R5011 7
Product Description Section 1 Release Notes
Version Description
4.1 New version containing error corrections and support of 800xA
System Version 4.1
4.1 Rollup 2 Includes new version check for higher system versions then 4.1.
This version checks allows to install device types in further System
rollups.
5.0 New Device Library Wizard containing:
• new graphical views
• wizard functionality for device type installation in 800xA
systems
• error corrections
• device installation information stored in the 800xA Aspect
Directory.
5.0 SP1 Enhanced Device Library Wizard containing:
• support for ABB Melody system environments
• support for ABB Freelance system environments
• new status message box with additional information during
device type installation process
• block functionality to prevent installation of device types not
released in a system version
• direct access to release notes from the selection window
8 2PAA102574R5011
Section 1 Release Notes Product Support
System Requirements
Please read the dedicated device type release notes for detailed information,
which system version and system environment is required for the device type
installation.
The Device Library Wizard SV5.0 SP1 is supporting the following system
environments and fieldbus protocols:
• Melody with AC 870P (Composer)
– PROFIBUS DP, PROFIBUS PA, HART
This version of Device Library Wizard can be used in connection with Composer
version 2.11D onwards, but not with CSV 5.0.
Product Support
Contact ABB technical support for assistance in problem reporting.
2PAA102574R5011 9
Limitation Section 1 Release Notes
Limitation
This version of Device Library Wizard does not support National Language Support
(NLS). All application windows of this tool are displayed in english language only.
2. Install the WinZip program on the PC with Windows 2000 operating system.
3. Double click on the Device Type file with the extension *.zip and extract it to
the following folder:
– For FOUNDATION Fieldbus:
<Installation path>\ABB Industrial IT\Engineer IT\ABB Device
Integration Library\FF Device Integration Library
– For HART:
<Installation path>\ABB Industrial IT\Engineer IT\ABB Device
Integration Library\HART Device Integration Library
– For PROFIBUS
<Installation path>\ABB Industrial IT\Engineer IT\ABB Device
Integration Library\PROFIBUS Device Integration Library
10 2PAA102574R5011
Section 1 Release Notes Limitation
4. Repeat step 3 till all required Device Types with zip-extension have been
extracted.
5. The extracted Device Types are now available in the Device Library Wizard for
installation.
Device Types
ABB cannot guarantee an operable ABB Industrial IT system, if device types,
installed with the Device Library Wizard, are modified manually. Only tested
software shall be installed on the system PCs. All software supplied in the Device
Integration Libraries or installed with the Device Library Wizard meets this
requirement.
The device types in the Device Integration Libraries are created by ABB and
tested for use in the ABB Industrial IT systems. ABB created these device types
based on data provided by individual device vendors (e.g. DDs, Device specific
DTMs and Asset Monitor behavior specifications), which ABB relies on as
accurately reflecting the actual device specification and behavior. Therefore,
ABB cannot assume liability for events that are caused by devices that are not
functioning according to fieldbus standards, or device specifications, or for events
that are caused by mismatches between the device behavior and the input data
provided by the device vendor.
2PAA102574R5011 11
Fixed Problems Section 1 Release Notes
Fixed Problems
Operational
Table 1 lists the major system or product operational issues that have been corrected
since the previous version or service pack. A brief description of the correction has
also been given.
800xADLW-OL-5000-006
12 2PAA102574R5011
Section 1 Release Notes Known Problems
Known Problems
Know problems may exist for a specific system environment as well as a general
issue for the Device Library Wizard. In the case, that the problem is identified in a
specific system environment only, the description of the problem includes the
system environment, e.g. 800xA with AC 800M (Fieldbus Builder).
Operational
Table 2 lists the issues that may exist and affect operational of the system or product
at time of release. Workarounds, clarifications, or helpful hints have been provided
for each issue wherever possible.
800xADLW-OL-5000-002
All Systems
HART Device Types, containing a DTM from Confirm the error message with OK. The DTM is
the ABB HART DTM Library (DD based not installed on the system node, therefore a re-
DTM, see device specific release notes), installation of the Device Type is required. Please
requires a selection in the DTM setup. select the Device Type in the Device Library Wizard
If a DTM is not selected in the ABB HART for re-installation again.
Library DTM setup, a runtime error ’9’ Notice: In case of a bulk installation the Device
appears. Types must be re-installed, where the DTM is
closed with the OK button in the error message
800xADLW-OL-5000-003 window.
2PAA102574R5011 13
Operational Section 1 Release Notes
800xADLW-OL-5000-005
800xA with AC 800M (Fieldbus Builder)
PROFIBUS Device Types not supporting Do not use this version of device type in SV5.0
Hardware Libraries in 800xA System onwards. Check ABB Solutionsbank for a new
Version 5.0 onwards do not get installed. version of object type supporting 800xA SV5.x.
Installation using DLW shows "could not find
the path ..\HWLib\Import"
800xADLW-OL-5000-007
All Systems
ABB Instrument Device Types with specific Disable the virus protection tool (e.g. McAfee)
ABB DTMs can be rejected by virus before starting device type installation via DLW.
protection tools during installation process. Enable the tool again after installation process.
800xADLW-OL-5000-008
Melody and Freelance Systems
The Device Library Wizard shows just a The Device Type may not be released for the
error message “Version check failed” in the system environment. Please read the device
log file, if the Device Type can not be specific release notes for detailed information.
installed. There is no additional information
for this case.
800xADLW-OL-5010-001
14 2PAA102574R5011
Section 1 Release Notes Operational
800xADLW-OL-5010-002
2PAA102574R5011 15
Operational Section 1 Release Notes
16 2PAA102574R5011
Appendix A Version Designation
Released Software
ABB Device Library Wizard is released in the version as listed in Table 3.
2PAA102574R5011 17
Released Software Appendix A Version Designation
18 2PAA102574R5011
BackCover.fm Page 19 Wednesday, October 20, 2004 10:27 AM
2PAA102574R5011. Printed in Sweden July 2007
Copyright © 2003-2007 by ABB. All Rights Reserved
® Registered Trademark of ABB.
™ Trademark of ABB.
http://www.abb.com