Professional Documents
Culture Documents
performance series
Models LCG90111, LCG90112
! Warning
To reduce the risk of a fire, explosion, and serious burns to
FEATURES of the LCGA9000 METER the body, handle and dispose of a used electronic control
properly:
4 Two decimal point precision
4 Accuracy to +/- 0.3% The electronic control contains a lithium battery. Do not
4 Push button calibration short circuit, charge, force over discharge, disassemble,
4 Totalization in gallons or liters crush, penetrate, incinerate or heat the battery to a tempera-
4 Minimum three year battery life ture exceeding 185º F (85º C). Any misuse or abuse of the
battery may cause it to leak or explode.
4 Low battery indicator
4
!
Replaceable battery
4 Only two parts: reduces maintenance
4 Uses 1/2AA 3V battery
Warning
Pressure Relief Procedure
Maximum Flow* 8 gpm 35 ltrs/min. To reduce the risk of serious bodily injury, including fluid
Minimum Flow* 0.25 gpm 1.0 ltr/min. injection or splashing in the eyes or on the skin, always fol-
Max. Operating Press. 1000 PSI 70 bar low this procedure when shutting down the system, and
before checking or repairing control handles or any other
Min. Operating Press. 5 PSI .35 bar part of the system.
Max Operating Temp. 110º F 45º C
Min. Operating Temp. -10º F -20º C 1. Turn off the power supply to the pump.
Accuracy (approved) +/- .4% +/- .3% 2. Trigger the control handle into a waste
container to relieve pressure in the line.
Weight (without handle) 2.5 lbs. 1.0 kg 3. Open any bleed-type master air valves
Weight (with handle) 3.0 lbs. 1.4 kg and fluid drain valves in the system.
Inlet/Outlet Connection 1/2" FNPT 1/2" FNPT 4. Leave the drain valve open until you are
*Tested with Mobil DTE-25 motor oil at ambient temperature. Min.-
ready to dispense fluid under pressure
Max. flow rates will vary with fluid viscosity.
again.
PROGRAMMING RECALIBRATION
LCGA9000 as installed on Inline Oil Control Gun LCGA9000 as installed on Inline Oil Control Gun
Model LCG90111 or LCG90112 Model LCG90111 or LCG90112
! Warning
change begins to flash.
M. Toggle reset button until the desired digit (5) appears.
To reduce the risk of a fire, explosion, and serious N. Toggle total button until the next digit you wish to
burns to the body, handle and dispose of a used elec- change begins to flash.
tronic control properly: O. Toggle reset button until the desired digit (2) appears.
P. Again depress the programming switch for 5 seconds
The electronic control contains a lithium battery. Do not and release to end the programming procedure. This oper-
short circuit, charge, force over discharge, disassemble,
crush, penetrate, incinerate or heat the battery to a ation will lock in the selected program and blank the dis-
temperature exceeding 185º F (85º C). Any misuse or play. Reinstall the register to the lube meter.
abuse of the battery may cause it to leak or explode.
NOTE: After programming, display will be blank. Depress
reset or total button to reactivate the display.
! Warning
Pressure Relief Procedure
To reduce the risk of serious bodily injury, including
fluid injection or splashing in the eyes or on the skin,
always follow this procedure when shutting down the
system, and before checking or repairing control han-
dles or any other part of the system.
! Warning
Model LCGA9050 To reduce the risk of a fire, explosion, and serious
burns to the body, handle and dispose of a used
3/8" MNPT angled rigid extension electronic control properly:
with manual non-drip nozzle.
The electronic control contains a lithium
battery. Do not short circuit, charge, force over
discharge, disassemble, crush, penetrate,
Model LCGA 9051 incinerate or heat the battery to a temperature
3/8" MNPT straight rigid extension with exceeding 185º F (85º C). Any misuse or abuse
manual non-drip nozzle. of the battery may cause it to leak or explode.
!
Model LCGA9041
1/2" MNPT flexible extension with
manual non-drip nozzle. Warning
Pressure Relief Procedure
To reduce the risk of serious bodily injury, including
fluid injection or splashing in the eyes or on the
skin, always follow this procedure when shutting
down the system, and before checking or repairing
Model LCGA9030 control handles or any other part of the system.
3/8" MNPT x 1/2" FNPT swivel for Legacy
inline electronic, mechanical and non- 1. Turn off the power supply to the pump.
metered control guns. 2. Trigger the control handle into a waste
container to relieve pressure in the line.
3. Open any bleed-type master air valves
and fluid drain valves in the system.
4. Leave the drain valve open until you are
Model LCGA9020 ready to dispense fluid under pressure again.
Manual non-drip nozzle. 3/8" FNPT inlet.
INLINE OIL CONTROL HANDLE - MODEL LCGA9060
Repair Parts Diagram