Professional Documents
Culture Documents
REVISIONS APPROVALS
Author Discipline Work Type Document Number Revision
TABLE OF CONTENTS
1 C E R T I F I C A T I O N................................................................................................ 2
2 DESIGN PARAMETERS AND CRITERIA .............................................................................. 3
2.1 Units of Measurement and Language 3
2.2 Applicable Codes, References and Standards 3
2.3 Structural Steel 3
2.3.1 Plates 3
2.3.2 Bolts 3
2.3.3 Corrosion Protection and Electrodes 4
2.3.4 Slenderness Ratio, KL/r 4
2.4 Reinforced Concrete 4
2.5 Displacements 4
2.6 Design Loads 4
2.6.1 Gravity Loads 4
2.6.1 Lateral Forces 5
2.6.2 Other Design Reaction Loads from Appurtenances and Ancillaries 7
2.7 Loading Combinations 7
3 DESIGN REPORT ...................................................................................................... 9
3.1 Introduction 9
3.2 Scope of Work 9
3.3 Structure Description 9
3.3.1 Configuration and Profile 9
3.3.2 Structure Analysis 10
3.3.3 Structural System 11
3.3.4 Analysis and Assumptions Made 11
3.4 Results and Findings 12
3.4.1 Existing Tower Structure and its Member Profile Evaluation 12
3.5 Conclusion and Recommendations 13
3.5.1 Concrete Pedestal and Base Plate Assembly 13
3.5.2 Feasibility of Additional Antenna Loadings 13
4 DESIGN COMPUTATIONS .......................................................................................... 14
4.1 OPEN TOWER DESIGNER REPORT 14
5 CONDITION OF ANALYSIS ......................................................................................... 15
6 REFERENCES ........................................................................................................ 16
1 CERTIFICATION
DITO TELECOMMUNITY
PROJECT: DESIGN OF A 40M HIGH 3-LEGGED TELECOMMUNICATION TOWER
SUBJECT: CERTIFICATION OF STRUCTURAL STABILITY – PROPOSED THREE-LEGGED SELF-SUPPORTING
TOWER
This is to certify that after a thorough review by performing structural analysis and design of the following:
Existing three-legged self-supporting tower structure as herein described to carry the following existing and
proposed antenna loads as presented in the structural investigation report enclosed with this certification;
the subject self-supporting tower structure - satisfactorily meets the strength and serviceability requirements based
on the NSCP Vol. 1, National Structural Code of the Philippines Vol. 1, 7th Edition, 2015wind load provisions for
Exposure D Category and basic wind speed of 310 kph in to sustain the applied loads as indicated in the survey
data/drawing. A structural analysis and design is presented in the structural investigation report, which forms part
of this certification to affirm the structural stability of the self-supporting tower structure as described above.
However, any further loads applied on the self-supporting tower structure that are not included in the above stated
loadings, in addition to the existing antenna attachments, as reflected on the proposed antenna plan / data furnished
by DITO TELECOMMUNITY and on the structural investigation report shall be beyond the scope and responsibility of
the undersigned.
This certification is being issued for the intended facility location with site ID: 3GT-40-280C-Z (310D) for whatever
technical purpose it may serve.
Joint Strength. For a two-dimensional and three-dimensional framing system the full strength of the
members at the joint shall be used, except for members whose full strength over its actual stress is greater
than 1.50. In this case, the actual strength shall be used.
Welded Connection. Full weld connections shall be used in all joints with its corresponding joint strength
requirements.
2.3.3 Corrosion Protection and Electrodes
Welding Electrodes shall be of class E70XX.
Hot-dipped galvanization shall be 85 microns.
2.3.4 Slenderness Ratio, KL/r
The slenderness ratio, KL/r, shall preferably not exceed:
200 for main legs;
240 for main compression members other than leg members;
250 for secondary members; and
300 for tension members, except for tension rod bracing and cables.
2.4 Reinforced Concrete
Concrete compressive strength: Concrete cylinder compressive strength measured will be:
Footings and pedestals: f’c = 21 MPa, unless noted otherwise
Reinforcing Steel for Concrete
Reinforcing bars yield strength: Reinforcement bars minimum specified yield strength measured will
be:
Footings, Tie Beams (if any) and Pedestals:
fy = 275 MPa for Ø16 up to Ø20 deformed bars, unless noted otherwise
fy = 275 MPa for Ø25 deformed bars and larger, unless noted otherwise
Ties, Stirrups:
fy = 275 MPa for Ø10 and Ø12 deformed bars, unless noted otherwise
2.5 Displacements
Maximum displacements at the extreme critical nodes on the structure (tilt and twist/twist and sway) shall
be calculated using the Open Tower software. (See Node Displacement summary). The maximum twist and
sway shall not exceed the minimum translational and/or rotational displacement of 1.0-degree.
2.6 Design Loads
The following loads shall be considered in this report:
2.6.1 Gravity Loads
Dead Load, D. Dead load means the weight of the structure itself.
Unit weights of major construction materials shall be as follows:
𝑉𝑉𝑠𝑠𝑠𝑠 = �(𝑉𝑉𝑠𝑠𝑠𝑠 2 /(1.6 ∗ 𝐼𝐼𝑤𝑤 )) ,based on Design Manual for Wind Load Provisions of NSCP C101-15
3second gust wind speed at 10m above ground in Exposure C as defined in 2.6.5.1 for a 50-year mean
recurrence interval, where 𝑽𝑽𝒔𝒔𝒔𝒔 = wind speed whose value may be taken as 310 kph for Occupancy
Category I (Table 103-1 Essential Facilities), refer to Figure 207A.5-1A Basic Wind Speeds for Occupancy
Category I and II Buildings and Other Structure, in kph
𝑰𝑰𝒘𝒘 = Importance factor based on Table 2-1 and Table 2-3, ANSI/TIA-222-G-2005, taken as equal to
1.00 for Class II: “Structures used for services that may be provided by other means such as: commercial
wireless communications; television and radio broadcasting; cellular, PCS, CATV, and
microwave communications” in this report.
𝑬𝑬𝑬𝑬𝑬𝑬𝑬𝑬𝑬𝑬𝑬𝑬𝑬𝑬𝑬𝑬 𝑪𝑪𝑪𝑪𝑪𝑪𝑪𝑪𝑪𝑪𝒐𝒐𝒓𝒓𝒓𝒓 = D based on NSCP Section 207A.7 or Article 2.6.5, ANSI/TIA-222-G-2005 .
𝒛𝒛 = height above ground level, in m
𝐺𝐺 = gust-effect factor, Article 2.6.7.1, ANSI/TIA-222-G-2005
(𝐸𝐸PA)𝑠𝑠 = 𝐶𝐶𝑓𝑓[𝐷𝐷𝑓𝑓 Ʃ𝐴𝐴𝑓𝑓 + 𝐷𝐷𝑟𝑟 Ʃ(𝐴𝐴𝑟𝑟𝑅𝑅𝑟𝑟)] Article 2.6.9.1.1, ANSI/TIA-222-G-2005
= effected projected area of structural components, in m2
𝑪𝑪𝒇𝒇 = structure force coefficient; which can be determined by the following expressions:
𝐴𝐴𝑓𝑓 = projected area of flat structural components in one face of the section, in m2
𝐴𝐴𝑟𝑟 = projected area of round structural components in one face of the section, in m2
𝑨𝑨𝒈𝒈 = projected area of gross section of one face as if the face were solid, in m2
Df = wind direction factor for flat structural components determined from Table 2-6
Dr = wind direction factor for round structural components determined from Table 2-6
Rr = reduction factor for a round element
= 0.36 + 0.26ε + 0.97ε2 - 0.63ε3 when C > 8.7 for no-ice conditions (supercritical flow)
where:
C = [𝑰𝑰𝒘𝒘 𝐾𝐾𝑍𝑍 𝐾𝐾𝑍𝑍𝑍𝑍 ]1/2 𝑉𝑉𝑠𝑠𝑠𝑠 D
D = outside diameter of the structural component without ice, m
StructDesign(GFSST_LRFD_TIA222G) 3GT-40-280C-Z-310D 5 Marjie S. Erispe-Gadon
Date: 24 December 2021 Civil/Structural Engineer
DITO TELECOMMUNITY DESIGN OF A 40M HIGH 3-LEGGED TELECOMMUNICATION TOWER
- STRUCTURAL INVESTIGATION REPORT FOR THREE-LEGGED SELF-SUPPORTING TOWER
Earthquake Load, E. Earthquake or seismic load may be considered as lateral forces that shall act
non-concurrently in the direction of each principal axis of the structure. These loads are actually
dynamic forces that shall be used, among which, for structures 60-m or more in height. However,
an alternative static lateral force is recommended based on rational analysis of well-established
principles of mechanic.
Earthquake load shall be calculated in accordance with the formula as given in Section 208 NSCP and
using Open Tower software.
Design Base Shear. The total design base shear in a given direction shall be determined from the
following equation:
𝐶𝐶𝑣𝑣 𝐼𝐼
𝑉𝑉 = 𝑊𝑊 in kN (eq. 208-8 NSCP C101-15)
𝑅𝑅𝑅𝑅
The total design base shear need not exceed the following equation:
2.5𝐶𝐶𝑎𝑎 𝐼𝐼
𝑉𝑉 = 𝑊𝑊 in kN (eq. 208-9 NSCP C101-15)
𝑅𝑅
The total design base shear shall not be less than the following equation:
𝑉𝑉 = 0.11𝐶𝐶𝑎𝑎 𝐼𝐼𝐼𝐼 in kN (eq. 208-10 NSCP C101-15)
In addition, for structure situated in seismic Zone 4, the total base shear shall not be less than the
following equation:
0.8𝑍𝑍𝑍𝑍𝑣𝑣 𝐼𝐼
𝑉𝑉 = 𝑊𝑊 in kN (eq. 208-11 NSCP C101-15)
𝑅𝑅
where:
𝑰𝑰 = seismic occupancy importance factor, taken as equal to 1.00 per Table 208-1
NSCP C101-15 for building structure (standard occupancy)
𝑪𝑪𝒂𝒂 = seismic coefficient per Table 208-7 NSCP C101-15 = 0.40𝑵𝑵𝒂𝒂
𝑪𝑪𝒗𝒗 = seismic coefficient per Table 208-8 NSCP C101-15 = 0.56𝑵𝑵𝒗𝒗
𝑵𝑵𝒂𝒂 = near-source factor per Table 208-5 NSCP C101-15 = 1.00
𝑵𝑵𝒗𝒗 = near-source factor per Table 208-6 NSCP C101-15 = 1.18
𝒁𝒁 = seismic zone factor per Table 208-3 NSCP C101-15= 0.4
𝑺𝑺𝐂𝐂 = soil profile type factor, per Table 208-2 NSCP C101-15 = SC
𝑹𝑹 = horizontal force factor depending on the type of structural system; in this case,
the value shall be taken as equal to 3.00 per Table 208-11B NSCP C101-15 for steel structure or Table
208-11A NSCP C101-15 for concrete building structure or Table 208-12 NSCP C101-15 for billboard and
signages.
𝑻𝑻 = fundamental period of structure, in second per Section 208.5.2.2 NSCP C101-15
𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺 𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺 𝑻𝑻𝑻𝑻𝑻𝑻𝑻𝑻 = per Table 208-4 NSCP C101-15
𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺 𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺 = per https://hazardhunter.georisk.gov.ph/
Qty Antenna Antenna Size, m Elev., m Antenna Link Azimuth Attached Design
Type AGL Status to Leg Criteria
marked
as
1 MW Ø1.80 31.0 1 - - B -
1 MW Ø1.20 28.0 1 - - B -
Note that the weight of and the wind force effect on the antenna holder support for the RF antenna and on
the microwave antenna supports are included in the analysis.
In addition, the three-legged self-supporting tower structure shall be analyzed, as minimum, to withstand
following appurtenance loads:
Brackets, frames required for antenna mounting and tower accessories like cable and climbing
ladders, obstruction lights, lightning protection;
12 coax feeder cables for RF antennas, 2 coax feeder cable per MW antenna; and/or
Electrical distribution boards (RRU units for 3G panel antenna), power and grounding cables, load
of maintenance personnel working on the tower and equipment where applicable.
2.7 Loading Combinations
All structural members and components shall be designed for the following load combinations, whichever
produces the greater stress. It is not necessary to consider combination of load, as may be applicable,
which is obvious to produce fewer stresses than other combination of loads.
The following load combinations shall be used for member check during its service level condition.
Dead, D 1.0
Wind, W 1.0
The following load combinations shall be used for member check during its strength level condition.
3 DESIGN REPORT
3.1 Introduction
This DESIGN REPORT presents the structural investigative analysis and evaluation of the members of the
existing design of the three-legged self-supporting tower structure located in -. Actual site condition with
topographic factors was not considered in the original and existing design. In order to fully assess the
structural integrity of the existing structure, a structural evaluation was requested to make a detailed
structural re-analysis, review and recommendation as to the soundness, feasibility and structural stability
of the structure.
3.2 Scope of Work
The scope of work that is performed in order to present this INVESTIGATION REPORT is based on the general
scope of work required by DITO TELECOMMUNITY, as follows:
Structural Analysis and Design
Based on the outcome of the preliminary assessment to check the safety of the existing three-
legged self-supporting tower for the proposed antenna load, structural computations of the
existing structure to include effect of loadings from accessories and proposed attachments shall
be prepared.
3.3 Structure Description
3.3.1 Configuration and Profile
The existing three-legged self-supporting tower structure is basically mounted on individual reinforced
concrete pedestals. The structure has a nominal height of approximately 40 meters with its legs mounted
on reinforced concrete pedestals and has a tapering width of 6.85 m at the base to 1.6 m at the top and has
10-m vertical straight portion at the top. The structure has the following existing main member profile
configuration:
-Lightning
brace for work Arrester
└45x45x5 main
1 5 CHS114x6 CHS60x5 platform (See
horizontal. - Work
DDD)
platform
└50x50x5 main
3 5 CHS140x8 CHS60x5 - -
horizontal.
└56x56x5 main
4 5 CHS159x10 CHS60x5 - -
horizontal.
Tower Ø600x35 thick base plate with 6-M48 anchor bolts and 250x16 thick stiffener plates
Base Plate
Base between bolts.
The structure configuration consists of predominantly x-bracing system for the entire tower. The self-
supporting tower structure is considered to be under Type 3 construction, on which the design is associated
with the member joint strength. The provisions of the NSCP, Vol. 1, National Structural Code of the
Philippines Vol. 1, 7th Edition, 2015are basically used in checking the stability of the structure members,
assessed to sustain the dead load, live load, wind and seismic forces as herein described. The investigative
analysis of the self-supporting tower structure is generated using the Open Tower software. It is used to
generate the 3D model, create all input specifications and all output reports and displays graphical
environment. These structural modelling and analysis input specifications are stored in a text file with
extension .MGB which can be analyzed and designed. The results can be viewed graphically. The MGB file
is processed by the Open Tower analysis to produce results that are stored in several files with extensions
such as OUT. The .OUT text file contains the printable output as created by the specifications. The other
files contain the results (node displacements, member / element forces, mode shapes, section forces,
section moments and section displacements, etc.).
The provisions of Section 207 of the NSCP, Vol. 1, National Structural Code of the Philippines Vol. 1, 7th
Edition, 2015(adapted from the 15thEdition of the American Institute of Steel Construction (AISC), 2016) are
basically used in checking the stability of the tower members, designed to sustain the wind velocity and
antenna attachments as herein described. A member marked “OK” signifies compliance with the AISC
combined stress criteria. Design stress results are shown as a tabulation of “MEMBER END FORCES/CHECK
CODE MEMBERS,” which are then used to check the design the members of the self-supporting tower
structure.
The self-supporting tower structure shall be analyzed having a basic wind speed of 310 kph with Exposure
D consideration. The coefficients used in the structural computation were taken from NSCP, Vol. I, Section
207, National Structural Code of the Philippines Vol. 1, 7th Edition, 2015.
In the structural investigation analysis, the members of the self-supporting tower are assumed to have
minimum specified yield strength as indicated in Section 2.3 of this report.
This report provides the detailed structural re-analysis of the existing tower for the current and additional
antenna loadings following DITO TELECOMMUNITY’s technical design requirements, governing
specifications, codes and standards. At the latter part of the report, conclusion and recommendation are
presented to guide DITO TELECOMMUNITY and its respective end users for whatever purpose this
document may serve.
Results of the analysis and design are summarized in the following pages of this report.
3.3.2 Structure Analysis
Generally, the structural modelling shall be analyzed based on the principle of
load resistance factor design (LRFD) concept. However, in this report, the load resistance factor design
(LRFD) conditions will be limited to strength and displacement requirements.
Methodology. A comprehensive load resistance factor design (LRFD) design approach will be used. Factored
load combinations will consider cases where continuously acting loads are both disadvantageous and
advantageous, with load factors adjusted as appropriate.
Where appropriate, the following computer program may be employed:
Open Tower - Two-dimensional / three-dimensional finite element analysis.
Design+ – General Engineering Assistance and Reference software for routine design work.
Customized spreadsheet programs developed by the designer in conformity with the requirements
of the applicable code.
The analysis of the structure will follow standard rational code procedures.
The existing self-supporting tower structure shall be analyzed as a three-dimensional space frame subjected
to both gravity loads and primarily for horizontal loads in accordance with the applicable code of practice.
The general method used to analyze this self-supporting tower structure is based on structural program
module in structural analysis known as Open Tower Program. The program implores a computerized three-
dimensional direct element stiffness matrix method.
With this program module, the self-supporting tower structure is analyzed as a three-dimensional space
subjected to wind and seismic loads, antenna loads (existing and proposed) and self-weight of the structure.
Various Open Tower outputs can be retrieved on a completed analyzed structure. However, outputs are
limited to the most critical load variations and structural code-checking such as the AISC code-checking,
member end forces, type of material used, joint coordinates, member incidences, member - critical
condition and graphical print output.
3.3.3 Structural System
The structure is made of structural steel space frame composed of PIPE LEG AND MAIN DIAGONAL, AND
ANGULAR HORIZONTAL, LATERAL AND SECONDARY BRACES. The vertical configuration of the structure is
a three-legged self-supporting tower, the whole structure being mounted on the reinforced concrete
pedestals.
3.3.4 Analysis and Assumptions Made
A comprehensive design approach will be used. Factored load combinations will consider cases where
continuously acting loads are both disadvantageous and advantageous, with load factors adjusted as
appropriate. However, for structural steel system, alternate stress design method will be employed where
unfactored load combinations will be considered at service stage.
The analysis and evaluation of structure and its components will follow standard rational code procedures.
In the structural investigative analysis and evaluation of the existing self-supporting tower members are
assumed to have minimum yield strength as stated in the material specifications – Section 2.3 of this report.
└50x50x5 main
3 5 CHS140x8 Adequate. Adequate. CHS60x5 Adequate. - -.
horizontal.
└56x56x5 main
4 5 CHS159x10 Adequate. Adequate. CHS60x5 Adequate. - -.
horizontal.
└56x56x5 main
5 5 CHS168x10 Adequate. Adequate. CHS76x5 Adequate. Varies (See DDD) Satisfactory.
horizontal.
└56x56x5 main
6 5 CHS180x10 Adequate. Adequate. CHS76x5 Adequate. Varies (See DDD) Satisfactory.
horizontal.
└56x56x5 main
7 5 CHS194x10 Adequate. Adequate. CHS76x5 Adequate. Varies (See DDD) Satisfactory.
horizontal.
└125x125x8 main
8 5 CHS194x10 Adequate. Adequate. CHS76x5 Varies (See DDD) Satisfactory.
horizontal.
Tower
Base Plate Ø600x35 thick base plate with 6-M60 anchor bolts and 250x16 thick stiffener plates between bolts. Adequate.
Base
Qty Antenna Antenna Size, m Elev., m Antenna Link Azimuth Attached Design
Type AGL Status to Leg Criteria
marked
as
1 MW Ø1.80 31.0 1 - - B -
1 MW Ø1.20 28.0 1 - - B -
4 DESIGN COMPUTATIONS
4.1 OPEN TOWER DESIGNER REPORT
Tower Summary
Tower Type 3-Leg Self-Supporting
Tower Height (m) 40
Base Elevation (m) 0.6
Bearing Angle with respect to North 0 deg
State Alaska
County Aleutians East
Latitude -
Longitude -
Active Scenario 3GT-40-MAXD-Z TAC20211216
Analysis Parameters
Type of Analysis Linear
Tower Geometry
Top Bottom
Section Range Section Length Face Diagonal Top Girt Bottom Girt
Section ID Width Width
(m) (m) Bracing Spacing (m) Offset (mm) Offset (mm)
(m) (m)
1 40-35 5.0000 K Down 1.65 1.6000 1.6000 0.0000 0.0000
2 35-30 5.0000 K Down 1.65 1.6000 1.6000 0.0000 0.0000
3 30-25 5.0000 K Down 1.65 1.6000 2.4750 0.0000 0.0000
4 25-20 5.0000 K Down 1.65 2.4750 3.3500 0.0000 0.0000
5 20-17.5 2.5000 K Up 2.5 3.3500 3.7870 0.0000 0.0000
6 17.5-15 2.5000 K Down 2.5 3.7870 4.2250 0.0000 0.0000
7 15-12.5 2.5000 K Up 2.5 4.2250 4.6620 0.0000 0.0000
8 12.5-10 2.5000 K Down 2.5 4.6620 5.1000 0.0000 0.0000
9 10-7.5 2.5000 K Up 2.5 5.1000 5.5380 0.0000 0.0000
10 7.5-5 2.5000 K Down 2.5 5.5380 5.9750 0.0000 0.0000
11 5-2.5 2.5000 K Up 2.5 5.9750 6.4130 0.0000 0.0000
12 2.5-0 2.5000 K Down 2.5 6.4130 6.8500 0.0000 0.0000
Member Properties
SECONDARYHORI
11 5-2.5 EA63X63X5 S 235 2 20 8.8_N
ZONTAL
SUBINNERBRACIN
10 7.5-5 XAEs56X56X5 S 235 2 20 8.8_N
G1
Discrete Appurtenances
Front Side
Weig
Mt Ant Horiz. Lat. Vert. Area Area Rel.
Mount Model ht(no Ks Ks
CL CL Mfg Location Offset Offset Offset (no (no Ka Azi
Type Number ice) (fr) (Si)
(m) (m) (m) (m) (m) ice) ice) (deg)
(kg)
(m2) (m2)
UPT:L70
UPT:PAMOU
39 38.5 UPT:DITO 0 2ports LegA 0 0 0 1.84 0.66 37.99 0.8 1 1 45
NT
18.5dbi
UPT:T20
UPT:PAMOU
39 38.5 UPT:DITO 20L6R01 LegA 0 0 0 1.33 0.63 46.49 0.8 1 1 135
NT
1
UPT:RRU
UPT:PAMOU
39 38.5 UPT:DITO -2.6G- LegA 0 0 0 0.21 0.08 25 0.8 1 1 225
NT
8T8R
UPT:RRU
UPT:PAMOU
39 38.5 UPT:DITO -2.6G- LegA 0 0 0 0.21 0.08 25 0.8 1 1 315
NT
8T8R
Front Side
Weig
Mt Ant Horiz. Lat. Vert. Area Area Rel.
Mount Model ht(no Ks Ks
CL CL Mfg Location Offset Offset Offset (no (no Ka Azi
Type Number ice) (fr) (Si)
(m) (m) (m) (m) (m) ice) ice) (deg)
(kg)
(m2) (m2)
UPT:L70
UPT:PAMOU
39 38.5 UPT:DITO 0 2ports LegB 0 0 0 1.84 0.66 37.99 0.8 1 1 45
NT
18.5dbi
UPT:T20
UPT:PAMOU
39 38.5 UPT:DITO 20L6R01 LegB 0 0 0 1.33 0.63 46.49 0.8 1 1 135
NT
1
UPT:RRU
UPT:PAMOU
39 38.5 UPT:DITO -2.6G- LegB 0 0 0 0.21 0.08 25 0.8 1 1 225
NT
8T8R
UPT:RRU
UPT:PAMOU
39 38.5 UPT:DITO -2.6G- LegB 0 0 0 0.21 0.08 25 0.8 1 1 315
NT
8T8R
UPT:L70
UPT:PAMOU
39 38.5 UPT:DITO 0 2ports LegC 0 0 0 1.84 0.66 37.99 0.8 1 1 45
NT
18.5dbi
UPT:T20
UPT:PAMOU
39 38.5 UPT:DITO 20L6R01 LegC 0 0 0 1.33 0.63 46.49 0.8 1 1 135
NT
1
UPT:RRU
UPT:PAMOU
39 38.5 UPT:DITO -2.6G- LegC 0 0 0 0.21 0.08 25 0.8 1 1 225
NT
8T8R
UPT:RRU
UPT:PAMOU
39 38.5 UPT:DITO -2.6G- LegC 0 0 0 0.21 0.08 25 0.8 1 1 315
NT
8T8R
UPT:AAU
UPT:PAMOU
36 35.5 UPT:DITO -NR- LegA 0 0 0 0.48 0.19 39.99 0.8 1 1 0
NT
64TR
UPT:RRU
UPT:PAMOU
36 35.5 UPT:DITO -2.6G- LegA 0 0 0 0.21 0.08 25 0.8 1 1 180
NT
8T8R
UPT:AAU
UPT:PAMOU
36 35.5 UPT:DITO -NR- LegB 0 0 0 0.48 0.19 39.99 0.8 1 1 0
NT
64TR
UPT:RRU
UPT:PAMOU
36 35.5 UPT:DITO -2.6G- LegB 0 0 0 0.21 0.08 25 0.8 1 1 180
NT
8T8R
UPT:AAU
UPT:PAMOU
36 35.5 UPT:DITO -NR- LegC 0 0 0 0.48 0.19 39.99 0.8 1 1 0
NT
64TR
UPT:RRU
UPT:PAMOU
36 35.5 UPT:DITO -2.6G- LegC 0 0 0 0.21 0.08 25 0.8 1 1 180
NT
8T8R
UPT:MWMO 0.6 CYL
33 33 Antenna LegA 0 0 0 0.28 0.28 30.59 1 1 1 0
UNT SHROUD
UPT:MWMO 1.2 CYL 127.4
31 31 Antenna LegB 0 0 0 1.13 1.13 1 1 1 0
UNT SHROUD 4
UPT:MWMO 1.8 CYL 222.2
28 28 Antenna LegC 0 0 0 2.54 2.54 1 1 1 0
UNT SHROUD 6
Miscellaneous Appurtenances
Side
Front
Horiz. Lat. Vert. Area Weight Rel.
MiscElv Model Area Ks Ks
Mfg Location Offset Offset Offset (no (no ice) Ka Azi
(m) Number (no ice) (fr) (Si)
(m) (m) (m) ice) (kg) (deg)
(m2)
(m2)
Miscellaneou
40 1"x12' Centroid 0 0 1.83 0.11 0.11 18.14 1 1 1 0
s
Linear Appurtenances
There is no data of this type
LEG SUMMARY
Tower
Section Member Pu (Comp) Pu (Tens) Capacity Ratio
Elevation ϕc Pn(kN) ϕt Pn(kN)
ID Description (kN) (kN) (%)
(m)
1 40-35 PIP114X6.0 65.2799 567.0303 57.4125 650.4221 11.51
Tower Applied
Section Member Connection Pu (Comp) Pu (Tens) Connection Capacity
Elevation Force
ID Description Type (kN) (kN) Capacity (kN) Ratio (%)
(m) (kN)
6 17.5-15 PIP168X10.0 Flange 640.5907 603.6532 603.6532 3358.9478 17.97
LEG DETAILS
Tower Fy Fu
Section Member Area
Elevation Gov. Axis K Lu (m) r (mm) KL/r (N/m (N/m
ID Description (mm2)
(m) m2) m2)
1 40-35 PIP114X6.0 z 1 1.65 38.1728 43.2245 20.3575 355 510
Clear
Section Diameter Base Plate Controlling
Anchor Rod Quantity Distance Ratio Result
ID (mm) Detail Load
(mm)
12 UPT:M48_8.8_N 48 6 0 c Axial+Shear 15.25 Pass
Member
Tower Edge Gage Pu Bolt Member
Section Member Pu (Tens) Block Capacity
Elevation Dist Line (Comp Shear Bearing
ID Description (kN) Shear Ratio (%)
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
37.999 38.849
1 40-35 PIP60X5.0 24 38.5421 112.6103 0 0 34.5
7 8
37.999 64.137
2 35-30 PIP60X5.0 24 63.6232 112.6103 0 0 56.96
7 7
37.999 31.439
3 30-25 PIP60X5.0 24 30.2106 112.6103 0 0 27.92
7 8
37.999 29.263
4 25-20 PIP60X5.0 24 28.1632 112.6103 0 0 25.99
7 9
44.499 36.064
5 20-17.5 PIP76X5.0 24 35.1116 112.6103 0 0 32.03
5 4
44.499
6 17.5-15 PIP76X5.0 24 38.964 36.6823 112.6103 0 0 34.6
5
44.499 32.937
7 15-12.5 PIP76X5.0 24 33.9109 112.6103 0 0 30.11
5 8
Member
Tower Edge Gage Pu Bolt Member
Section Member Pu (Tens) Block Capacity
Elevation Dist Line (Comp Shear Bearing
ID Description (kN) Shear Ratio (%)
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
44.499 36.949
8 12.5-10 PIP76X5.0 24 35.6261 112.6103 0 0 32.81
5 5
44.499
9 10-7.5 PIP76X5.0 24 33.54 33.929 112.6103 0 0 30.13
5
44.499 38.220
10 7.5-5 PIP76X5.0 24 36.0742 112.6103 0 0 33.94
5 2
44.499 39.600
11 5-2.5 PIP76X5.0 24 37.9573 112.6103 0 0 35.17
5 8
37.999 44.879
12 2.5-0 PIP76X5.0 24 40.0429 112.6103 0 0 39.85
7 6
Member
Segment Edge Gage Pu Bolt Member
Section Segmen Member Pu (Tens) Block Capacity
Elevation Dist Line (Comp Shear Bearing
ID t ID Description (kN) Shear Ratio (%)
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
37.999
1 1 40-38.3 PIP60X5.0 24 5.1414 4.8129 112.6103 0 0 4.57
7
37.999 33.236
1 2 38.3-36.65 PIP60X5.0 24 32.9232 112.6103 0 0 29.51
7 4
37.999 38.849
1 3 36.65-35 PIP60X5.0 24 38.5421 112.6103 0 0 34.5
7 8
37.999 50.891
2 1 35-33.3 PIP60X5.0 24 50.55 112.6103 0 0 45.19
7 1
37.999 57.404
2 2 33.3-31.65 PIP60X5.0 24 56.8519 112.6103 0 0 50.98
7 6
37.999 64.137
2 3 31.65-30 PIP60X5.0 24 63.6232 112.6103 0 0 56.96
7 7
37.999 27.065
3 1 30-28.3 PIP60X5.0 24 25.9345 112.6103 0 0 24.03
7 5
37.999 31.311
3 2 28.3-26.65 PIP60X5.0 24 30.2828 112.6103 0 0 27.8
7 2
37.999 31.439
3 3 26.65-25 PIP60X5.0 24 30.2106 112.6103 0 0 27.92
7 8
37.999 29.263
4 1 25-23.3 PIP60X5.0 24 28.1632 112.6103 0 0 25.99
7 9
37.999 28.329
4 2 23.3-21.65 PIP60X5.0 24 27.3339 112.6103 0 0 25.16
7 4
37.999 28.960
4 3 21.65-20 PIP60X5.0 24 28.0153 112.6103 0 0 25.72
7 8
44.499 36.064
5 1 20-17.5 PIP76X5.0 24 35.1116 112.6103 0 0 32.03
5 4
44.499
6 1 17.5-15 PIP76X5.0 24 38.964 36.6823 112.6103 0 0 34.6
5
44.499 32.937
7 1 15-12.5 PIP76X5.0 24 33.9109 112.6103 0 0 30.11
5 8
44.499 36.949
8 1 12.5-10 PIP76X5.0 24 35.6261 112.6103 0 0 32.81
5 5
44.499
9 1 10-7.5 PIP76X5.0 24 33.54 33.929 112.6103 0 0 30.13
5
44.499 38.220
10 1 7.5-5 PIP76X5.0 24 36.0742 112.6103 0 0 33.94
5 2
44.499 39.600
11 1 5-2.5 PIP76X5.0 24 37.9573 112.6103 0 0 35.17
5 8
37.999 44.879
12 1 2.5-0 PIP76X5.0 24 40.0429 112.6103 0 0 39.85
7 6
Tower Fy Fu
Section Member Area
Elevation Gov. Axis K Lu (m) r (mm) KL/r (N/m (N/m
ID Description (cm2)
(m) m2) m2)
1 40-35 PIP60X5.0 y 1.138 1.8337 19.4899 107.0425 8.6394 235 360
2 35-30 PIP60X5.0 y 1.138 1.8337 19.4899 107.0425 8.6394 235 360
3 30-25 PIP60X5.0 y 1.067 2.0642 19.4899 112.9551 8.6394 235 360
4 25-20 PIP60X5.0 y 0.998 2.3527 19.4899 120.438 8.6394 235 360
5 20-17.5 PIP76X5.0 x 1 3.0119 25.1184 119.9539 11.1527 235 360
6 17.5-15 PIP76X5.0 x 0.969 3.2755 25.1184 126.3964 11.1527 235 360
7 15-12.5 PIP76X5.0 x 0.969 3.2755 25.1184 126.3962 11.1527 235 360
8 12.5-10 PIP76X5.0 x 0.94 3.5733 25.1184 133.6886 11.1527 235 360
9 10-7.5 PIP76X5.0 x 0.94 3.5733 25.1184 133.6886 11.1527 235 360
10 7.5-5 PIP76X5.0 x 0.913 3.8976 25.1184 141.6283 11.1527 235 360
11 5-2.5 PIP76X5.0 y 0.913 3.8976 25.1184 141.6283 11.1527 235 360
12 2.5-0 PIP76X5.0 x 0.889 4.2422 25.1184 150.0669 11.1527 235 360
Member
Tower Edge Gage Pu Bolt Member
Section Member Pu (Tens) Block Capacity
Elevation Dist Line (Comp Shear Bearing
ID Description (kN) Shear Ratio (%)
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
27.500 11.036
5 20-17.5 EA55X55X5 24 11.0368 56.3051 35.8552 33.1884 33.25
6 8
Member
Segment Edge Gage Pu Bolt Member
Section Segmen Member Pu (Tens) Block Capacity
Elevation Dist Line (Comp Shear Bearing
ID t ID Description (kN) Shear Ratio (%)
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
27.500 11.036
5 1 20-17.5 EA55X55X5 24 11.0368 56.3051 35.8552 33.1884 33.25
6 8
TOPHORIZONTAL DETAIL
Tower Fy Fu
Section Member Area
Elevation Gov. Axis K Lu (m) r (mm) KL/r (N/m (N/m
ID Description (cm2)
(m) m2) m2)
5 20-17.5 EA55X55X5 y 1 3.35 16.998 197.0822 5.25 235 360
Segment
Section Segment Member Area Fy Fu
Elevation Gov. Axis K Lu (m) r (mm) KL/r
ID ID Description (cm2) (N/mm2) (N/mm2)
(m)
197.08
5 1 20-17.5 EA55X55X5 y 1 3.35 16.998 5.25 235 360
22
HORIZONTAL SUMMARY
Member
Tower Edge Gage Pu Bolt Member
Section Member Pu (Tens) Block Capacity
Elevation Dist Line (Comp Shear Bearing
ID Description (kN) Shear Ratio (%)
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
22.500 16.939
1 40-35 EA45X45X5 24 16.9366 56.3051 29.1052 33.1884 58.19
6 1
24.999 27.990
2 35-30 EA50X50X5 24 28.2141 56.3051 32.4811 33.1884 86.86
9 6
24.999 18.381
3 30-25 EA50X50X5 24 18.9276 56.3051 32.4811 33.1884 58.27
9 1
27.500 20.025
4 25-20 EA55X55X5 24 20.4934 56.3051 35.8552 33.1884 61.75
6 2
27.500 11.050
6 17.5-15 EA55X55X5 24 11.0502 56.3051 35.8552 33.1884 33.3
6 2
27.500 12.764
8 12.5-10 EA63X63X6 24 12.7641 56.3051 55.9863 39.8261 32.05
6 1
27.500 14.152
10 7.5-5 EA55X55X5 24 14.1522 56.3051 35.8552 33.1884 42.64
6 2
62.500 15.577
12 2.5-0 EA125X125X8 30 15.5776 175.9185 181.5577 186.9523 8.86
5 6
Member
Segment Edge Gage Pu Bolt Member
Section Segmen Member Pu (Tens) Block Capacity
Elevation Dist Line (Comp Shear Bearing
ID t ID Description (kN) Shear Ratio (%)
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
22.500
1 1 40-38.3 EA45X45X5 24 2.5554 2.5231 56.3051 29.1052 33.1884 8.67
6
22.500 16.939
1 2 38.3-36.65 EA45X45X5 24 16.9366 56.3051 29.1052 33.1884 58.19
6 1
22.500 16.835
1 3 36.65-35 EA45X45X5 24 16.9274 56.3051 29.1052 33.1884 58.16
6 4
24.999 21.523
2 1 35-33.3 EA50X50X5 24 21.5944 56.3051 32.4811 33.1884 66.48
9 2
24.999 24.901
2 2 33.3-31.65 EA50X50X5 24 25.1064 56.3051 32.4811 33.1884 77.3
9 3
24.999 27.990
2 3 31.65-30 EA50X50X5 24 28.2141 56.3051 32.4811 33.1884 86.86
9 6
24.999 18.777
3 1 30-28.3 EA50X50X5 24 17.9689 56.3051 32.4811 33.1884 55.32
9 4
24.999 17.538
3 2 28.3-26.65 EA50X50X5 24 17.8709 56.3051 32.4811 33.1884 55.02
9 1
24.999 18.381
3 3 26.65-25 EA50X50X5 24 18.9276 56.3051 32.4811 33.1884 58.27
9 1
Member
Segment Edge Gage Pu Bolt Member
Section Segmen Member Pu (Tens) Block Capacity
Elevation Dist Line (Comp Shear Bearing
ID t ID Description (kN) Shear Ratio (%)
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
27.500
4 1 25-23.3 EA55X55X5 24 17.845 18.2974 56.3051 35.8552 33.1884 55.13
6
27.500 18.691
4 2 23.3-21.65 EA55X55X5 24 19.1225 56.3051 35.8552 33.1884 57.62
6 9
27.500 20.025
4 3 21.65-20 EA55X55X5 24 20.4934 56.3051 35.8552 33.1884 61.75
6 2
27.500 11.050
6 1 17.5-15 EA55X55X5 24 11.0502 56.3051 35.8552 33.1884 33.3
6 2
27.500 12.764
8 1 12.5-10 EA63X63X6 24 12.7641 56.3051 55.9863 39.8261 32.05
6 1
27.500 14.152
10 1 7.5-5 EA55X55X5 24 14.1522 56.3051 35.8552 33.1884 42.64
6 2
62.500 15.577
12 1 2.5-0 EA125X125X8 30 15.5776 175.9185 181.5577 186.9523 8.86
5 6
HORIZONTAL DETAIL
Tower Fy Fu
Section Member Area
Elevation Gov. Axis K Lu (m) r (mm) KL/r (N/m (N/m
ID Description (cm2)
(m) m2) m2)
1 40-35 EA45X45X5 y 1.162 0.8 8.8239 105.3312 4.25 235 360
2 35-30 EA50X50X5 z 1.237 0.8 9.8292 100.6952 4.75 235 360
3 30-25 EA50X50X5 z 1.04 1.0931 9.8292 115.6062 4.75 235 360
4 25-20 EA55X55X5 z 1 1.5306 10.8373 141.2373 5.25 235 360
6 17.5-15 EA55X55X5 z 1 1.5148 10.8373 139.7771 5.25 235 360
8 12.5-10 EA63X63X6 z 1 1.865 12.3995 150.4095 7.2 235 360
10 7.5-5 EA55X55X5 y 1 2.7688 16.998 162.887 5.25 235 360
12 2.5-0 EA125X125X8 y 1.016 2.8856 24.8336 118.0993 19.36 235 360
Segment
Section Segment Member Area Fy Fu
Elevation Gov. Axis K Lu (m) r (mm) KL/r
ID ID Description (cm2) (N/mm2) (N/mm2)
(m)
105.33
1 1 40-38.3 EA45X45X5 y 1.162 0.8 8.8239 4.25 235 360
12
105.33
1 2 38.3-36.65 EA45X45X5 y 1.162 0.8 8.8239 4.25 235 360
12
105.33
1 3 36.65-35 EA45X45X5 z 1.162 0.8 8.8239 4.25 235 360
12
100.69
2 1 35-33.3 EA50X50X5 y 1.237 0.8 9.8292 4.75 235 360
52
100.69
2 2 33.3-31.65 EA50X50X5 z 1.237 0.8 9.8292 4.75 235 360
52
100.69
2 3 31.65-30 EA50X50X5 z 1.237 0.8 9.8292 4.75 235 360
52
100.69
3 1 30-28.3 EA50X50X5 y 1.237 0.8 9.8292 4.75 235 360
52
108.26
3 2 28.3-26.65 EA50X50X5 z 1.122 0.9488 9.8292 4.75 235 360
2
115.60
3 3 26.65-25 EA50X50X5 z 1.04 1.0931 9.8292 4.75 235 360
62
117.09
4 1 25-23.3 EA55X55X5 z 1.025 1.2375 10.8373 5.25 235 360
47
127.91
4 2 23.3-21.65 EA55X55X5 z 1 1.3862 10.8373 5.25 235 360
52
141.23
4 3 21.65-20 EA55X55X5 z 1 1.5306 10.8373 5.25 235 360
73
Segment
Section Segment Member Area Fy Fu
Elevation Gov. Axis K Lu (m) r (mm) KL/r
ID ID Description (cm2) (N/mm2) (N/mm2)
(m)
139.77
6 1 17.5-15 EA55X55X5 z 1 1.5148 10.8373 5.25 235 360
71
150.40
8 1 12.5-10 EA63X63X6 z 1 1.865 12.3995 7.2 235 360
95
162.88
10 1 7.5-5 EA55X55X5 y 1 2.7688 16.998 5.25 235 360
7
118.09
12 1 2.5-0 EA125X125X8 y 1.016 2.8856 24.8336 19.36 235 360
93
SECONDARYHORIZONTAL SUMMARY
Member
Tower Edge Gage Pu Bolt Member
Section Member Pu (Tens) Block Capacity
Elevation Dist Line (Comp Shear Bearing
ID Description (kN) Shear Ratio (%)
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
31.499 15.547
11 5-2.5 EA63X63X5 30 15.5475 175.9185 71.6245 116.8452 21.71
8 5
Member
Segment Edge Gage Pu Bolt Member
Section Segmen Member Pu (Tens) Block Capacity
Elevation Dist Line (Comp Shear Bearing
ID t ID Description (kN) Shear Ratio (%)
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
31.499 15.547
11 1 5-2.5 EA63X63X5 30 15.5475 175.9185 71.6245 116.8452 21.71
8 5
SECONDARYHORIZONTAL DETAIL
Tower Fy Fu
Section Member Area
Elevation Gov. Axis K Lu (m) r (mm) KL/r (N/m (N/m
ID Description (cm2)
(m) m2) m2)
11 5-2.5 EA63X63X5 z 1 2.9875 12.4544 239.8742 6.05 235 360
Segment
Section Segment Member Area Fy Fu
Elevation Gov. Axis K Lu (m) r (mm) KL/r
ID ID Description (cm2) (N/mm2) (N/mm2)
(m)
239.87
11 1 5-2.5 EA63X63X5 z 1 2.9875 12.4544 6.05 235 360
42
INNERBRACING SUMMARY
Member
Tower Edge Gage Pu Bolt Member
Section Member Pu (Tens) Block Capacity
Elevation Dist Line (Comp Shear Bearing
ID Description (kN) Shear Ratio (%)
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
27.999
5 20-17.5 XAEs56X56X5 24 0.0974 0 56.3051 36.5314 33.1884 0.17
7
31.499
10 7.5-5 EA63X63X6 24 0.0949 0.0862 56.3051 49.5075 39.8261 0.22
8
Member
Segment Edge Gage Pu Bolt Member
Section Segmen Member Pu (Tens) Block Capacity
Elevation Dist Line (Comp Shear Bearing
ID t ID Description (kN) Shear Ratio (%)
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
27.999
5 1 20-17.5 XAEs56X56X5 24 0.0974 0 56.3051 36.5314 33.1884 0.17
7
31.499
10 1 7.5-5 EA63X63X6 24 0.0949 0.0862 56.3051 49.5075 39.8261 0.22
8
INNERBRACING DETAIL
Tower Fy Fu
Section Member Area
Elevation Gov. Axis K Lu (m) r (mm) KL/r (N/m (N/m
ID Description (cm2)
(m) m2) m2)
5 20-17.5 XAEs56X56X5 z 1 1.675 11.0392 151.7327 5.35 235 360
10 7.5-5 EA63X63X6 y 1 2.7688 19.4325 142.4801 7.2 235 360
Segment
Section Segment Member Area Fy Fu
Elevation Gov. Axis K Lu (m) r (mm) KL/r
ID ID Description (cm2) (N/mm2) (N/mm2)
(m)
151.73
5 1 20-17.5 XAEs56X56X5 z 1 1.675 11.0392 5.35 235 360
27
142.48
10 1 7.5-5 EA63X63X6 y 1 2.7688 19.4325 7.2 235 360
01
SUBINNERBRACING1 SUMMARY
Member
Tower Edge Gage Pu Bolt Member
Section Member Pu (Tens) Block Capacity
Elevation Dist Line (Comp Shear Bearing
ID Description (kN) Shear Ratio (%)
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
27.999
10 7.5-5 XAEs56X56X5 24 0.0741 0 56.3051 36.5314 33.1884 0.13
7
Member
Segment Edge Gage Pu Bolt Member
Section Segmen Member Pu (Tens) Block Capacity
Elevation Dist Line (Comp Shear Bearing
ID t ID Description (kN) Shear Ratio (%)
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
27.999
10 1 7.5-5 XAEs56X56X5 24 0.0741 0 56.3051 36.5314 33.1884 0.13
7
SUBINNERBRACING1 DETAIL
Tower Fy Fu
Section Member Area
Elevation Gov. Axis K Lu (m) r (mm) KL/r (N/m (N/m
ID Description (cm2)
(m) m2) m2)
10 7.5-5 XAEs56X56X5 z 1 1.3844 11.0392 125.4059 5.35 235 360
PB2 SUMMARY
Member
Tower Edge Gage Pu Bolt Member
Section Member Pu (Tens) Block Capacity
Elevation Dist Line (Comp Shear Bearing
ID Description (kN) Shear Ratio (%)
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
24.999
1 40-35 EA50X50X4 24 0.0865 0.0858 56.3051 25.9849 26.5507 0.33
9
24.999
2 35-30 EA50X50X5 24 0.0875 0.0891 56.3051 32.4811 33.1884 0.27
9
31.499
3 30-25 EA63X63X5 24 0.0937 0.0699 56.3051 41.2563 33.1884 0.21
8
31.499
4 25-20 EA63X63X5 24 0.064 0.027 56.3051 41.2563 33.1884 0.11
8
27.999
6 17.5-15 XAEs56X56X5 24 0.18 0.1319 56.3051 36.5314 33.1884 0.4
7
31.499
8 12.5-10 EA63X63X6 18 0.1693 0.1104 15.255 48.8595 29.4581 1.11
8
Print Date:04/01/2022 OpenTower CE : 10.02.00.44 Page 16 of 43
PB2 BOLT SEGMENT SUMMARY
Member
Segment Edge Gage Pu Bolt Member
Section Segmen Member Pu (Tens) Block Capacity
Elevation Dist Line (Comp Shear Bearing
ID t ID Description (kN) Shear Ratio (%)
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
31.499
1 1 40-38.3 EA63X63X5 24 0.0513 0.0456 27.135 41.2563 33.1884 0.19
8
24.999
1 2 38.3-36.65 EA50X50X4 24 0.0865 0.0858 56.3051 25.9849 26.5507 0.33
9
24.999
2 1 35-33.3 EA50X50X5 24 0.0875 0.0891 56.3051 32.4811 33.1884 0.27
9
31.499
3 1 30-28.3 EA63X63X5 24 0.0937 0.0699 56.3051 41.2563 33.1884 0.21
8
31.499
4 1 25-23.3 EA63X63X5 24 0.064 0.027 56.3051 41.2563 33.1884 0.11
8
27.999
6 1 17.5-15 XAEs56X56X5 24 0.18 0.1319 56.3051 36.5314 33.1884 0.4
7
31.499
8 1 12.5-10 EA63X63X6 18 0.1693 0.1104 15.255 48.8595 29.4581 1.11
8
PB2 DETAIL
Tower Fy Fu
Section Member Area
Elevation Gov. Axis K Lu (m) r (mm) KL/r (N/m (N/m
ID Description (cm2)
(m) m2) m2)
1 40-35 EA50X50X4 y 1.509 0.9238 15.5295 89.7436 3.84 235 360
2 35-30 EA50X50X5 y 1.5 0.9238 15.3899 90.0135 4.75 235 360
3 30-25 EA63X63X5 z 1.201 1.0667 12.4544 102.8249 6.05 235 360
4 25-20 EA63X63X5 z 1 1.6501 12.4544 132.4894 6.05 235 360
6 17.5-15 XAEs56X56X5 z 1 1.5148 11.0392 137.2207 5.35 235 360
8 12.5-10 EA63X63X6 z 1 1.865 12.3995 150.4095 7.2 235 360
Segment
Section Segment Member Area Fy Fu
Elevation Gov. Axis K Lu (m) r (mm) KL/r
ID ID Description (cm2) (N/mm2) (N/mm2)
(m)
102.82
1 1 40-38.3 EA63X63X5 z 1.201 1.0667 12.4544 6.05 235 360
49
89.743
1 2 38.3-36.65 EA50X50X4 y 1.509 0.9238 15.5295 3.84 235 360
6
90.013
2 1 35-33.3 EA50X50X5 y 1.5 0.9238 15.3899 4.75 235 360
5
102.82
3 1 30-28.3 EA63X63X5 z 1.201 1.0667 12.4544 6.05 235 360
49
132.48
4 1 25-23.3 EA63X63X5 z 1 1.6501 12.4544 6.05 235 360
94
137.22
6 1 17.5-15 XAEs56X56X5 z 1 1.5148 11.0392 5.35 235 360
07
150.40
8 1 12.5-10 EA63X63X6 z 1 1.865 12.3995 7.2 235 360
95
PB3 SUMMARY
Member
Tower Edge Gage Pu Bolt Member
Section Member Pu (Tens) Block Capacity
Elevation Dist Line (Comp Shear Bearing
ID Description (kN) Shear Ratio (%)
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
31.499
1 40-35 EA63X63X5 24 0.0489 0.0475 27.135 41.2563 33.1884 0.18
8
31.499
2 35-30 EA63X63X5 24 0.0478 0.0486 56.3051 41.2563 33.1884 0.15
8
27.999
6 17.5-15 XAEs56X56X5 24 0.1686 0.1978 56.3051 36.5314 33.1884 0.6
7
31.499
8 12.5-10 EA63X63X6 18 0.1411 0.1862 15.255 48.8595 29.4581 1.22
8
Member
Segment Edge Gage Pu Bolt Member
Section Segmen Member Pu (Tens) Block Capacity
Elevation Dist Line (Comp Shear Bearing
ID t ID Description (kN) Shear Ratio (%)
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
31.499
1 2 38.3-36.65 EA63X63X5 24 0.0489 0.0475 27.135 41.2563 33.1884 0.18
8
31.499
2 1 35-33.3 EA63X63X5 24 0.0478 0.0486 56.3051 41.2563 33.1884 0.15
8
27.999
6 1 17.5-15 XAEs56X56X5 24 0.1686 0.1978 56.3051 36.5314 33.1884 0.6
7
31.499
8 1 12.5-10 EA63X63X6 18 0.1411 0.1862 15.255 48.8595 29.4581 1.22
8
PB3 DETAIL
Tower Fy Fu
Section Member Area
Elevation Gov. Axis K Lu (m) r (mm) KL/r (N/m (N/m
ID Description (cm2)
(m) m2) m2)
1 40-35 EA63X63X5 z 1.901 0.5334 12.4544 81.4131 6.05 235 360
2 35-30 EA63X63X5 z 1.901 0.5334 12.4544 81.4131 6.05 235 360
6 17.5-15 XAEs56X56X5 z 1 1.8935 11.0392 171.5259 5.35 235 360
8 12.5-10 EA63X63X6 z 1 2.3312 12.3995 188.0119 7.2 235 360
Segment
Section Segment Member Area Fy Fu
Elevation Gov. Axis K Lu (m) r (mm) KL/r
ID ID Description (cm2) (N/mm2) (N/mm2)
(m)
81.413
1 2 38.3-36.65 EA63X63X5 z 1.901 0.5334 12.4544 6.05 235 360
1
81.413
2 1 35-33.3 EA63X63X5 z 1.901 0.5334 12.4544 6.05 235 360
1
171.52
6 1 17.5-15 XAEs56X56X5 z 1 1.8935 11.0392 5.35 235 360
59
188.01
8 1 12.5-10 EA63X63X6 z 1 2.3312 12.3995 7.2 235 360
19
Member
Tower Edge Gage Pu Bolt Member
Section Member Pu (Tens) Block Capacity
Elevation Dist Line (Comp Shear Bearing
ID Description (kN) Shear Ratio (%)
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
31.499
6 17.5-15 EA63X63X6 24 0.0789 0 56.3051 49.5075 39.8261 0.14
8
31.499
8 12.5-10 EA63X63X6 18 0.0908 0 56.3051 43.6755 27.3845 0.16
8
Member
Segment Edge Gage Pu Bolt Member
Section Segmen Member Pu (Tens) Block Capacity
Elevation Dist Line (Comp Shear Bearing
ID t ID Description (kN) Shear Ratio (%)
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
31.499
6 1 17.5-15 EA63X63X6 24 0.0789 0 56.3051 49.5075 39.8261 0.14
8
31.499
8 1 12.5-10 EA63X63X6 18 0.0908 0 56.3051 43.6755 27.3845 0.16
8
PB4 DETAIL
Tower Fy Fu
Section Member Area
Elevation Gov. Axis K Lu (m) r (mm) KL/r (N/m (N/m
ID Description (cm2)
(m) m2) m2)
6 17.5-15 EA63X63X6 z 1.061 1.3254 12.3995 113.4478 7.2 235 360
8 12.5-10 EA63X63X6 z 1 1.6319 12.3995 131.6083 7.2 235 360
Segment
Section Segment Member Area Fy Fu
Elevation Gov. Axis K Lu (m) r (mm) KL/r
ID ID Description (cm2) (N/mm2) (N/mm2)
(m)
113.44
6 1 17.5-15 EA63X63X6 z 1.061 1.3254 12.3995 7.2 235 360
78
131.60
8 1 12.5-10 EA63X63X6 z 1 1.6319 12.3995 7.2 235 360
83
PB6 SUMMARY
Member
Tower Edge Gage Pu Bolt Member
Section Member Pu (Tens) Block Capacity
Elevation Dist Line (Comp Shear Bearing
ID Description (kN) Shear Ratio (%)
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
49.999
12 2.5-0 100X100X8EA 24 0.2508 0 56.3051 123.4107 61.8411 0.45
9
Member
Segment Edge Gage Pu Bolt Member
Section Segmen Member Pu (Tens) Block Capacity
Elevation Dist Line (Comp Shear Bearing
ID t ID Description (kN) Shear Ratio (%)
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
49.999
12 1 2.5-0 100X100X8EA 24 0.2508 0 56.3051 123.4107 61.8411 0.45
9
PB6 DETAIL
Tower Fy Fu
Section Member Area
Elevation Gov. Axis K Lu (m) r (mm) KL/r (N/m (N/m
ID Description (cm2)
(m) m2) m2)
12 2.5-0 100X100X8EA y 1.146 2.8856 31.0875 106.4113 14.9916 275 430
Segment
Section Segment Member Area Fy Fu
Elevation Gov. Axis K Lu (m) r (mm) KL/r
ID ID Description (cm2) (N/mm2) (N/mm2)
(m)
106.41
12 1 2.5-0 100X100X8EA y 1.146 2.8856 31.0875 14.9916 275 430
13
PB7 SUMMARY
Member
Segment Edge Gage Pu Bolt Member
Section Segmen Member Pu (Tens) Block Capacity
Elevation Dist Line (Comp Shear Bearing
ID t ID Description (kN) Shear Ratio (%)
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
31.499
12 1 2.5-0 EA63X63X6 24 0.2087 0 56.3051 49.5075 39.8261 0.37
8
PB7 DETAIL
Tower Fy Fu
Section Member Area
Elevation Gov. Axis K Lu (m) r (mm) KL/r (N/m (N/m
ID Description (cm2)
(m) m2) m2)
12 2.5-0 EA63X63X6 z 1.428 0.8016 12.3995 92.3224 7.2 235 360
Print Date:04/01/2022 OpenTower CE : 10.02.00.44 Page 20 of 43
PB7 DETAIL SEGMENT
Segment
Section Segment Member Area Fy Fu
Elevation Gov. Axis K Lu (m) r (mm) KL/r
ID ID Description (cm2) (N/mm2) (N/mm2)
(m)
92.322
12 1 2.5-0 EA63X63X6 z 1.428 0.8016 12.3995 7.2 235 360
4
PB8 SUMMARY
Member
Tower Edge Gage Pu Bolt Member
Section Member Pu (Tens) Block Capacity
Elevation Dist Line (Comp Shear Bearing
ID Description (kN) Shear Ratio (%)
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
37.500
12 2.5-0 EA75X75X6 24 0.3465 0 56.3051 59.2263 39.8261 0.62
6
Member
Segment Edge Gage Pu Bolt Member
Section Segmen Member Pu (Tens) Block Capacity
Elevation Dist Line (Comp Shear Bearing
ID t ID Description (kN) Shear Ratio (%)
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
37.500
12 1 2.5-0 EA75X75X6 24 0.3465 0 56.3051 59.2263 39.8261 0.62
6
PB8 DETAIL
Tower Fy Fu
Section Member Area
Elevation Gov. Axis K Lu (m) r (mm) KL/r (N/m (N/m
ID Description (cm2)
(m) m2) m2)
12 2.5-0 EA75X75X6 z 1.055 1.603 14.8239 114.0691 8.64 235 360
Tilt
Maximum Reaction Load Combination Moment (kNm) Axial (kN) Shear (kN)
Compression C 10 - 1.2D + 1.6Wo-240° 5.15 948.75 152.68
Overturning Overturning
Torque
Node Id Load Combination Vertical (kN) Shear x (kN) Shear z (kN) Moment Moment
(kNm)
(Mx) (kNm) (Mz) (kNm)
155 C 1 - 1.00 SW 30.0310 0.0420 5.1580 −0.6400 −0.0060 0.0060
C 2 - 1.2D + 1.6Wo-
155 937.1600 1.7990 151.1510 3.6680 −2.7170 −0.1920
0°
Overturning Overturning
Torque
Node Id Load Combination Vertical (kN) Shear x (kN) Shear z (kN) Moment Moment
(kNm)
(Mx) (kNm) (Mz) (kNm)
C 3 - 1.2D + 1.6Wo-
155 805.8770 −2.2580 129.3120 2.6680 6.3780 −0.4720
30°
C 4 - 1.2D + 1.6Wo-
155 481.1160 −5.6780 77.2290 1.1560 13.7050 −0.6020
60°
C 5 - 1.2D + 1.6Wo-
155 50.2360 −7.4940 8.2420 −0.8010 17.2620 −0.6540
90°
C 6 - 1.2D + 1.6Wo-
155 −389.9640 −7.6050 −62.8090 −3.0850 16.7440 −0.5950
120°
C 7 - 1.2D + 1.6Wo-
155 −727.9550 −4.7130 −116.0510 −4.1930 10.0820 −0.1760
150°
C 8 - 1.2D + 1.6Wo-
155 −843.2600 −1.5140 −134.1800 −4.5510 2.4330 0.2200
180°
C 9 - 1.2D + 1.6Wo-
155 −728.8390 2.4340 −116.1810 −4.1930 −6.4130 0.5310
210°
C 10 - 1.2D + 1.6Wo-
155 −408.4140 6.4130 −65.5620 −3.0970 −14.7080 0.5750
240°
C 11 - 1.2D + 1.6Wo-
155 29.8840 7.4780 5.2040 −0.8140 −17.0310 0.5680
270°
C 12 - 1.2D + 1.6Wo-
155 464.2050 6.7900 74.7060 1.1460 −15.2210 0.4300
300°
C 13 - 1.2D + 1.6Wo-
155 796.9740 4.8180 127.9850 2.6630 −10.2100 0.1610
330°
C 14 - 0.9D + 1.6Wo-
155 928.1510 1.7870 149.6030 3.8600 −2.7150 −0.1940
0°
C 15 - 0.9D + 1.6Wo-
155 796.8680 −2.2710 127.7650 2.8600 6.3800 −0.4740
30°
C 16 - 0.9D + 1.6Wo-
155 472.1060 −5.6900 75.6820 1.3480 13.7070 −0.6040
60°
C 17 - 0.9D + 1.6Wo-
155 41.2260 −7.5070 6.6940 −0.6090 17.2640 −0.6560
90°
C 18 - 0.9D + 1.6Wo-
155 −398.9730 −7.6180 −64.3560 −2.8940 16.7460 −0.5960
120°
C 19 - 0.9D + 1.6Wo-
155 −736.9640 −4.7260 −117.5990 −4.0010 10.0840 −0.1770
150°
C 20 - 0.9D + 1.6Wo-
155 −852.2690 −1.5270 −135.7270 −4.3590 2.4340 0.2190
180°
C 21 - 0.9D + 1.6Wo-
155 −737.8490 2.4210 −117.7290 −4.0010 −6.4110 0.5290
210°
Print Date:04/01/2022 OpenTower CE : 10.02.00.44 Page 26 of 43
Tower Reaction Summary Cont...
Overturning Overturning
Torque
Node Id Load Combination Vertical (kN) Shear x (kN) Shear z (kN) Moment Moment
(kNm)
(Mx) (kNm) (Mz) (kNm)
210°
C 22 - 0.9D + 1.6Wo-
155 −417.4230 6.4000 −67.1090 −2.9050 −14.7070 0.5730
240°
C 23 - 0.9D + 1.6Wo-
155 20.8740 7.4660 3.6560 −0.6220 −17.0290 0.5660
270°
C 24 - 0.9D + 1.6Wo-
155 455.1960 6.7780 73.1590 1.3370 −15.2190 0.4290
300°
C 25 - 0.9D + 1.6Wo-
155 787.9650 4.8060 126.4380 2.8550 −10.2080 0.1590
330°
C 26 - 1.2D + 1.6Wo-
155 630.4410 1.1880 101.3300 1.8800 −1.7690 −0.1230
0°:PL1
C 27 - 1.2D + 1.6Wo-
155 928.4840 1.7990 150.2350 3.9030 −2.7160 −0.1920
0°:PL2
C 28 - 1.2D + 1.6Wo-
155 543.7550 −1.4180 86.9920 1.2670 4.1100 −0.2880
30°:PL1
C 29 - 1.2D + 1.6Wo-
155 798.5560 −2.2900 128.5400 2.8670 6.4110 −0.4880
30°:PL2
C 30 - 1.2D + 1.6Wo-
155 329.4670 −3.6180 52.8010 0.3710 8.8510 −0.3620
60°:PL1
C 31 - 1.2D + 1.6Wo-
155 476.9840 −5.7320 76.7930 1.2680 13.7590 −0.6290
60°:PL2
C 32 - 1.2D + 1.6Wo-
155 45.2670 −4.7910 7.5240 −0.7890 11.1560 −0.3920
90°:PL1
C 33 - 1.2D + 1.6Wo-
155 50.2360 −7.5560 8.2420 −0.8010 17.3240 −0.6850
90°:PL2
C 34 - 1.2D + 1.6Wo-
155 −245.0960 −4.8700 −39.1060 −2.1600 10.8260 −0.3570
120°:PL1
C 35 - 1.2D + 1.6Wo-
155 −385.7280 −7.6600 −62.3610 −3.2000 16.7990 −0.6220
120°:PL2
C 36 - 1.2D + 1.6Wo-
155 −467.8810 −3.0140 −74.0400 −2.7960 6.5190 −0.0960
150°:PL1
C 37 - 1.2D + 1.6Wo-
155 −720.6330 −4.7450 −115.2790 −4.3920 10.1130 −0.1910
150°:PL2
C 38 - 1.2D + 1.6Wo-
155 −543.9720 −0.9670 −85.9440 −2.9970 1.5790 0.1460
180°:PL1
C 39 - 1.2D + 1.6Wo-
155 −834.7890 −1.5140 −133.2860 −4.7810 2.4320 0.2200
180°:PL2
Overturning Overturning
Torque
Node Id Load Combination Vertical (kN) Shear x (kN) Shear z (kN) Moment Moment
(kNm)
(Mx) (kNm) (Mz) (kNm)
C 40 - 1.2D + 1.6Wo-
155 −468.4540 1.5670 −74.1240 −2.7960 −4.1380 0.3310
210°:PL1
C 41 - 1.2D + 1.6Wo-
155 −721.5190 2.4660 −115.4090 −4.3910 −6.4450 0.5470
210°:PL2
C 42 - 1.2D + 1.6Wo-
155 −257.0890 4.1300 −40.8960 −2.1670 −9.5070 0.3480
240°:PL1
C 43 - 1.2D + 1.6Wo-
155 −404.1790 6.4680 −65.1150 −3.2120 −14.7640 0.6020
240°:PL2
C 44 - 1.2D + 1.6Wo-
155 32.0370 4.8160 5.5490 −0.7980 −11.0100 0.3400
270°:PL1
C 45 - 1.2D + 1.6Wo-
155 29.8840 7.5410 5.2040 −0.8140 −17.0930 0.5990
270°:PL2
C 46 - 1.2D + 1.6Wo-
155 318.4760 4.3780 51.1610 0.3640 −9.8430 0.2550
300°:PL1
C 47 - 1.2D + 1.6Wo-
155 460.0730 6.8440 74.2700 1.2570 −15.2750 0.4570
300°:PL2
C 48 - 1.2D + 1.6Wo-
155 537.9700 3.1180 86.1300 1.2640 −6.6070 0.0910
330°:PL1
C 49 - 1.2D + 1.6Wo-
155 789.6520 4.8500 127.2130 2.8620 −10.2410 0.1770
330°:PL2
C 50 - 0.9D + 1.6Wo-
155 621.4320 1.1750 99.7820 2.0720 −1.7680 −0.1240
0°:PL1
C 51 - 0.9D + 1.6Wo-
155 919.4740 1.7860 148.6880 4.0950 −2.7150 −0.1940
0°:PL2
C 52 - 0.9D + 1.6Wo-
155 534.7460 −1.4300 85.4450 1.4590 4.1120 −0.2900
30°:PL1
C 53 - 0.9D + 1.6Wo-
155 789.5470 −2.3030 126.9930 3.0590 6.4120 −0.4890
30°:PL2
C 54 - 0.9D + 1.6Wo-
155 320.4580 −3.6310 51.2540 0.5630 8.8530 −0.3640
60°:PL1
C 55 - 0.9D + 1.6Wo-
155 467.9740 −5.7450 75.2460 1.4600 13.7610 −0.6310
60°:PL2
C 56 - 0.9D + 1.6Wo-
155 36.2570 −4.8040 5.9760 −0.5970 11.1570 −0.3940
90°:PL1
C 57 - 0.9D + 1.6Wo-
155 41.2260 −7.5690 6.6940 −0.6090 17.3260 −0.6870
90°:PL2
C 58 - 0.9D + 1.6Wo-
155 −254.1060 −4.8830 −40.6530 −1.9680 10.8280 −0.3580
120°:PL1
Print Date:04/01/2022 OpenTower CE : 10.02.00.44 Page 28 of 43
Tower Reaction Summary Cont...
Overturning Overturning
Torque
Node Id Load Combination Vertical (kN) Shear x (kN) Shear z (kN) Moment Moment
(kNm)
(Mx) (kNm) (Mz) (kNm)
120°:PL1
C 59 - 0.9D + 1.6Wo-
155 −394.7380 −7.6730 −63.9090 −3.0080 16.8010 −0.6240
120°:PL2
C 60 - 0.9D + 1.6Wo-
155 −476.8910 −3.0270 −75.5870 −2.6040 6.5210 −0.0980
150°:PL1
C 61 - 0.9D + 1.6Wo-
155 −729.6430 −4.7570 −116.8260 −4.2000 10.1150 −0.1930
150°:PL2
C 62 - 0.9D + 1.6Wo-
155 −552.9810 −0.9790 −87.4910 −2.8060 1.5810 0.1440
180°:PL1
C 63 - 0.9D + 1.6Wo-
155 −843.7990 −1.5260 −134.8340 −4.5890 2.4340 0.2190
180°:PL2
C 64 - 0.9D + 1.6Wo-
155 −477.4640 1.5540 −75.6720 −2.6040 −4.1360 0.3300
210°:PL1
C 65 - 0.9D + 1.6Wo-
155 −730.5280 2.4530 −116.9560 −4.2000 −6.4430 0.5450
210°:PL2
C 66 - 0.9D + 1.6Wo-
155 −266.0980 4.1180 −42.4430 −1.9750 −9.5060 0.3470
240°:PL1
C 67 - 0.9D + 1.6Wo-
155 −413.1880 6.4560 −66.6620 −3.0200 −14.7620 0.6010
240°:PL2
C 68 - 0.9D + 1.6Wo-
155 23.0280 4.8030 4.0010 −0.6060 −11.0090 0.3390
270°:PL1
C 69 - 0.9D + 1.6Wo-
155 20.8740 7.5280 3.6560 −0.6220 −17.0910 0.5970
270°:PL2
C 70 - 0.9D + 1.6Wo-
155 309.4670 4.3650 49.6140 0.5560 −9.8410 0.2540
300°:PL1
C 71 - 0.9D + 1.6Wo-
155 451.0640 6.8320 72.7220 1.4490 −15.2730 0.4560
300°:PL2
C 72 - 0.9D + 1.6Wo-
155 528.9610 3.1050 84.5820 1.4560 −6.6060 0.0890
330°:PL1
C 73 - 0.9D + 1.6Wo-
155 780.6430 4.8370 125.6650 3.0540 −10.2390 0.1750
330°:PL2
C 74 - 1.0D + 1.0Ws-
155 123.1480 0.2120 20.3570 −0.0520 −0.2690 −0.0140
0°
C 75 - 1.0D + 1.0Ws-
155 109.6520 −0.2470 18.0870 −0.1700 0.7400 −0.0520
30°
C 76 - 1.0D + 1.0Ws-
155 76.0610 −0.6270 12.6180 −0.3740 1.5440 −0.0730
60°
Overturning Overturning
Torque
Node Id Load Combination Vertical (kN) Shear x (kN) Shear z (kN) Moment Moment
(kNm)
(Mx) (kNm) (Mz) (kNm)
C 77 - 1.0D + 1.0Ws-
155 31.4090 −0.8200 5.3570 −0.6430 1.9230 −0.0810
90°
C 78 - 1.0D + 1.0Ws-
155 −14.1480 −0.8140 −2.1040 −0.9430 1.8380 −0.0720
120°
C 79 - 1.0D + 1.0Ws-
155 −49.0220 −0.4850 −7.6850 −1.1090 1.0990 −0.0230
150°
C 80 - 1.0D + 1.0Ws-
155 −60.9690 −0.1090 −9.5960 −1.1640 0.2310 0.0260
180°
C 81 - 1.0D + 1.0Ws-
155 −49.1080 0.3390 −7.6980 −1.1090 −0.7540 0.0670
210°
C 82 - 1.0D + 1.0Ws-
155 −15.9350 0.7730 −2.3710 −0.9440 −1.6520 0.0800
240°
C 83 - 1.0D + 1.0Ws-
155 29.4350 0.8930 5.0620 −0.6440 −1.9110 0.0820
270°
C 84 - 1.0D + 1.0Ws-
155 74.4200 0.8090 12.3730 −0.3750 −1.7010 0.0660
300°
C 85 - 1.0D + 1.0Ws-
155 108.7880 0.5700 17.9580 −0.1700 −1.1230 0.0320
330°
C 86 - 1.2D + 1.0
155 119.1940 0.0530 18.2700 −0.9280 −0.0090 0.0110
seismic in 0°
C 87 - 1.2D + 1.0
155 108.0530 −0.0920 16.6520 −0.9070 0.5400 −0.0110
seismic in 30°
C 88 - 1.2D + 1.0
155 77.6160 −0.1990 12.2300 −0.8480 0.9430 −0.0290
seismic in 60°
C 89 - 1.2D + 1.0
155 36.0380 −0.2380 6.1890 −0.7680 1.0910 −0.0370
seismic in 90°
C 90 - 1.2D + 1.0
155 −5.5410 −0.2010 0.1490 −0.6870 0.9450 −0.0340
seismic in 120°
C 91 - 1.2D + 1.0
155 −35.9780 −0.0950 −4.2730 −0.6290 0.5440 −0.0190
seismic in 150°
C 92 - 1.2D + 1.0
155 −47.1190 0.0490 −5.8910 −0.6070 −0.0050 0.0020
seismic in 180°
C 93 - 1.2D + 1.0
155 −35.9780 0.1940 −4.2730 −0.6290 −0.5550 0.0250
seismic in 210°
C 94 - 1.2D + 1.0
155 −5.5410 0.3000 0.1490 −0.6870 −0.9580 0.0420
seismic in 240°
C 95 - 1.2D + 1.0
155 36.0380 0.3400 6.1900 −0.7680 −1.1060 0.0510
seismic in 270°
Print Date:04/01/2022 OpenTower CE : 10.02.00.44 Page 30 of 43
Tower Reaction Summary Cont...
Overturning Overturning
Torque
Node Id Load Combination Vertical (kN) Shear x (kN) Shear z (kN) Moment Moment
(kNm)
(Mx) (kNm) (Mz) (kNm)
seismic in 270°
C 96 - 1.2D + 1.0
155 77.6160 0.3020 12.2300 −0.8480 −0.9600 0.0470
seismic in 300°
C 97 - 1.2D + 1.0
155 108.0530 0.1970 16.6520 −0.9070 −0.5580 0.0330
seismic in 330°
C 98 - 0.9D + 1.0
155 110.1850 0.0400 16.7230 −0.7360 −0.0080 0.0100
seismic in 0°
C 99 - 0.9D + 1.0
155 99.0440 −0.1050 15.1040 −0.7150 0.5420 −0.0130
seismic in 30°
C 2 - 1.2D + 1.6Wo-
154 −396.2860 50.0860 40.9990 19.9950 7.9940 0.8140
0°
C 3 - 1.2D + 1.6Wo-
154 62.0280 −14.2020 5.5430 21.6410 11.3380 0.7250
30°
C 4 - 1.2D + 1.6Wo-
154 498.0610 −73.7590 −30.6200 17.9590 11.4050 0.7040
60°
Overturning Overturning
Torque
Node Id Load Combination Vertical (kN) Shear x (kN) Shear z (kN) Moment Moment
(kNm)
(Mx) (kNm) (Mz) (kNm)
C 5 - 1.2D + 1.6Wo-
154 817.9580 −116.4870 −59.5460 10.4940 8.9170 0.5300
90°
C 6 - 1.2D + 1.6Wo-
154 944.1540 −132.0210 −74.9950 −0.0010 4.0800 0.1110
120°
C 7 - 1.2D + 1.6Wo-
154 802.8920 −108.9040 −68.3820 −10.0140 −2.8600 −0.3440
150°
C 8 - 1.2D + 1.6Wo-
154 468.9650 −60.2080 −45.8440 −17.7290 −9.0590 −0.6070
180°
C 9 - 1.2D + 1.6Wo-
154 26.7660 1.9260 −12.4250 −20.4070 −12.7580 −0.7000
210°
C 10 - 1.2D + 1.6Wo-
154 −428.0460 64.6010 24.8580 −17.4420 −13.4660 −0.8600
240°
C 11 - 1.2D + 1.6Wo-
154 −738.1220 105.2430 53.0390 −9.6380 −10.3740 −0.5200
270°
C 12 - 1.2D + 1.6Wo-
154 −850.6880 117.9280 66.5860 0.1930 −5.1380 −0.1220
300°
C 13 - 1.2D + 1.6Wo-
154 −736.9510 99.3560 62.8640 10.7320 1.3940 0.3250
330°
C 14 - 0.9D + 1.6Wo-
154 −406.0150 51.4560 41.7830 19.8830 8.1790 0.8140
0°
C 15 - 0.9D + 1.6Wo-
154 52.2990 −12.8320 6.3280 21.5280 11.5230 0.7250
30°
C 16 - 0.9D + 1.6Wo-
154 488.3320 −72.3900 −29.8350 17.8470 11.5900 0.7040
60°
C 17 - 0.9D + 1.6Wo-
154 808.2300 −115.1170 −58.7610 10.3820 9.1030 0.5300
90°
C 18 - 0.9D + 1.6Wo-
154 934.4250 −130.6520 −74.2100 −0.1140 4.2650 0.1110
120°
C 19 - 0.9D + 1.6Wo-
154 793.1630 −107.5350 −67.5970 −10.1260 −2.6750 −0.3440
150°
C 20 - 0.9D + 1.6Wo-
154 459.2360 −58.8390 −45.0590 −17.8410 −8.8740 −0.6070
180°
C 21 - 0.9D + 1.6Wo-
154 17.0370 3.2950 −11.6400 −20.5200 −12.5730 −0.7000
210°
C 22 - 0.9D + 1.6Wo-
154 −437.7750 65.9700 25.6430 −17.5540 −13.2810 −0.8600
240°
C 23 - 0.9D + 1.6Wo-
154 −747.8510 106.6120 53.8240 −9.7500 −10.1890 −0.5200
270°
Print Date:04/01/2022 OpenTower CE : 10.02.00.44 Page 32 of 43
Tower Reaction Summary Cont...
Overturning Overturning
Torque
Node Id Load Combination Vertical (kN) Shear x (kN) Shear z (kN) Moment Moment
(kNm)
(Mx) (kNm) (Mz) (kNm)
270°
C 24 - 0.9D + 1.6Wo-
154 −860.4170 119.2970 67.3710 0.0810 −4.9530 −0.1220
300°
C 25 - 0.9D + 1.6Wo-
154 −746.6800 100.7250 63.6490 10.6190 1.5800 0.3260
330°
C 26 - 1.2D + 1.6Wo-
154 −248.3010 31.0640 25.7310 13.0470 5.0100 0.5010
0°:PL1
C 27 - 1.2D + 1.6Wo-
154 −391.9480 49.6620 40.8180 20.1020 7.9200 0.8420
0°:PL2
C 28 - 1.2D + 1.6Wo-
154 53.9410 −11.1160 2.4500 14.1690 7.0790 0.4390
30°:PL1
C 29 - 1.2D + 1.6Wo-
154 62.0290 −14.2330 5.5980 21.6950 11.3690 0.7570
30°:PL2
C 30 - 1.2D + 1.6Wo-
154 341.4990 −50.2120 −21.2660 11.8410 7.0300 0.4310
60°:PL1
C 31 - 1.2D + 1.6Wo-
154 493.9300 −73.4080 −30.3550 17.9490 11.5280 0.7310
60°:PL2
C 32 - 1.2D + 1.6Wo-
154 552.4390 −78.2710 −40.2070 7.0490 5.3540 0.3290
90°:PL1
C 33 - 1.2D + 1.6Wo-
154 810.8150 −115.8490 −59.1420 10.4240 9.1000 0.5450
90°:PL2
C 34 - 1.2D + 1.6Wo-
154 635.7890 −88.5050 −50.2920 0.2710 2.1940 0.0720
120°:PL1
C 35 - 1.2D + 1.6Wo-
154 935.6820 −131.2460 −74.5470 −0.1160 4.2780 0.1110
120°:PL2
C 36 - 1.2D + 1.6Wo-
154 542.8230 −73.3900 −45.9060 −6.2260 −2.2750 −0.2080
150°:PL1
C 37 - 1.2D + 1.6Wo-
154 795.5710 −108.2190 −68.0230 −10.1400 −2.7040 −0.3600
150°:PL2
C 38 - 1.2D + 1.6Wo-
154 322.6790 −41.4660 −31.0730 −11.2620 −6.2200 −0.3670
180°:PL1
C 39 - 1.2D + 1.6Wo-
154 464.7300 −59.7940 −45.6680 −17.8330 −8.9870 −0.6350
180°:PL2
C 40 - 1.2D + 1.6Wo-
154 31.0170 −0.6960 −9.1200 −13.0540 −8.5210 −0.4230
210°:PL1
C 41 - 1.2D + 1.6Wo-
154 26.7660 1.9580 −12.4800 −20.4620 −12.7900 −0.7320
210°:PL2
Overturning Overturning
Torque
Node Id Load Combination Vertical (kN) Shear x (kN) Shear z (kN) Moment Moment
(kNm)
(Mx) (kNm) (Mz) (kNm)
C 42 - 1.2D + 1.6Wo-
154 −268.8490 40.4340 15.3310 −11.1900 −8.8860 −0.5310
240°:PL1
C 43 - 1.2D + 1.6Wo-
154 −423.8110 64.2410 24.5870 −17.4310 −13.5930 −0.8870
240°:PL2
C 44 - 1.2D + 1.6Wo-
154 −473.3040 67.1290 33.7810 −6.1780 −6.8210 −0.3230
270°:PL1
C 45 - 1.2D + 1.6Wo-
154 −730.9790 104.6050 52.6350 −9.5680 −10.5570 −0.5350
270°:PL2
C 46 - 1.2D + 1.6Wo-
154 −547.5900 75.4920 42.6190 0.1710 −3.4060 −0.0790
300°:PL1
C 47 - 1.2D + 1.6Wo-
154 −842.4240 117.1730 66.1500 0.3050 −5.3320 −0.1220
300°:PL2
C 48 - 1.2D + 1.6Wo-
154 −472.7210 63.3500 40.1220 7.0060 0.8030 0.1960
330°:PL1
C 49 - 1.2D + 1.6Wo-
154 −729.6290 98.6710 62.5050 10.8580 1.2380 0.3410
330°:PL2
C 50 - 0.9D + 1.6Wo-
154 −258.0300 32.4330 26.5150 12.9350 5.1960 0.5010
0°:PL1
C 51 - 0.9D + 1.6Wo-
154 −401.6760 51.0310 41.6030 19.9900 8.1050 0.8420
0°:PL2
C 52 - 0.9D + 1.6Wo-
154 44.2120 −9.7470 3.2340 14.0570 7.2640 0.4390
30°:PL1
C 53 - 0.9D + 1.6Wo-
154 52.3000 −12.8640 6.3830 21.5830 11.5550 0.7570
30°:PL2
C 54 - 0.9D + 1.6Wo-
154 331.7700 −48.8430 −20.4810 11.7280 7.2150 0.4310
60°:PL1
C 55 - 0.9D + 1.6Wo-
154 484.2010 −72.0390 −29.5710 17.8360 11.7130 0.7310
60°:PL2
C 56 - 0.9D + 1.6Wo-
154 542.7100 −76.9020 −39.4230 6.9370 5.5400 0.3290
90°:PL1
C 57 - 0.9D + 1.6Wo-
154 801.0860 −114.4800 −58.3570 10.3120 9.2850 0.5450
90°:PL2
C 58 - 0.9D + 1.6Wo-
154 626.0600 −87.1360 −49.5070 0.1590 2.3790 0.0720
120°:PL1
C 59 - 0.9D + 1.6Wo-
154 925.9530 −129.8770 −73.7630 −0.2280 4.4640 0.1110
120°:PL2
C 60 - 0.9D + 1.6Wo-
154 533.0940 −72.0200 −45.1210 −6.3380 −2.0890 −0.2080
150°:PL1
Print Date:04/01/2022 OpenTower CE : 10.02.00.44 Page 34 of 43
Tower Reaction Summary Cont...
Overturning Overturning
Torque
Node Id Load Combination Vertical (kN) Shear x (kN) Shear z (kN) Moment Moment
(kNm)
(Mx) (kNm) (Mz) (kNm)
150°:PL1
C 61 - 0.9D + 1.6Wo-
154 785.8420 −106.8500 −67.2380 −10.2520 −2.5190 −0.3600
150°:PL2
C 62 - 0.9D + 1.6Wo-
154 312.9510 −40.0970 −30.2880 −11.3740 −6.0350 −0.3670
180°:PL1
C 63 - 0.9D + 1.6Wo-
154 455.0010 −58.4250 −44.8830 −17.9460 −8.8020 −0.6350
180°:PL2
C 64 - 0.9D + 1.6Wo-
154 21.2880 0.6730 −8.3350 −13.1660 −8.3360 −0.4230
210°:PL1
C 65 - 0.9D + 1.6Wo-
154 17.0370 3.3270 −11.6950 −20.5740 −12.6040 −0.7320
210°:PL2
C 66 - 0.9D + 1.6Wo-
154 −278.5780 41.8030 16.1150 −11.3030 −8.7010 −0.5310
240°:PL1
C 67 - 0.9D + 1.6Wo-
154 −433.5400 65.6100 25.3720 −17.5430 −13.4070 −0.8870
240°:PL2
C 68 - 0.9D + 1.6Wo-
154 −483.0330 68.4980 34.5650 −6.2900 −6.6350 −0.3230
270°:PL1
C 69 - 0.9D + 1.6Wo-
154 −740.7080 105.9740 53.4200 −9.6800 −10.3710 −0.5350
270°:PL2
C 70 - 0.9D + 1.6Wo-
154 −557.3190 76.8610 43.4030 0.0590 −3.2200 −0.0790
300°:PL1
C 71 - 0.9D + 1.6Wo-
154 −852.1530 118.5420 66.9350 0.1930 −5.1460 −0.1220
300°:PL2
C 72 - 0.9D + 1.6Wo-
154 −482.4500 64.7190 40.9070 6.8940 0.9880 0.1960
330°:PL1
C 73 - 0.9D + 1.6Wo-
154 −739.3580 100.0400 63.2900 10.7460 1.4240 0.3410
330°:PL2
C 74 - 1.0D + 1.0Ws-
154 −12.6390 1.2620 2.0480 2.5000 0.2710 0.0980
0°
C 75 - 1.0D + 1.0Ws-
154 34.6700 −5.4750 −1.6600 2.6490 0.6800 0.0920
30°
C 76 - 1.0D + 1.0Ws-
154 79.8220 −11.7370 −5.4680 2.2230 0.7380 0.0870
60°
C 77 - 1.0D + 1.0Ws-
154 112.9400 −16.2180 −8.5230 1.3900 0.5010 0.0620
90°
C 78 - 1.0D + 1.0Ws-
154 125.9490 −17.8240 −10.1550 0.2510 −0.0140 0.0110
120°
Overturning Overturning
Torque
Node Id Load Combination Vertical (kN) Shear x (kN) Shear z (kN) Moment Moment
(kNm)
(Mx) (kNm) (Mz) (kNm)
C 79 - 1.0D + 1.0Ws-
154 111.4800 −15.4170 −9.4940 −0.8190 −0.7690 −0.0450
150°
C 80 - 1.0D + 1.0Ws-
154 76.9980 −10.3090 −7.1410 −1.6190 −1.4670 −0.0780
180°
C 81 - 1.0D + 1.0Ws-
154 31.2530 −3.7800 −3.6300 −1.8690 −1.9110 −0.0900
210°
C 82 - 1.0D + 1.0Ws-
154 −15.7230 2.7840 0.2870 −1.5120 −2.0310 −0.1030
240°
C 83 - 1.0D + 1.0Ws-
154 −47.8860 7.0620 3.2700 −0.6460 −1.7340 −0.0620
270°
C 84 - 1.0D + 1.0Ws-
154 −59.5710 8.3920 4.7170 0.4280 −1.1810 −0.0120
300°
C 85 - 1.0D + 1.0Ws-
154 −47.7740 6.4260 4.3360 1.5500 −0.4660 0.0420
330°
C 86 - 1.2D + 1.0
154 −2.6630 −0.4180 0.1790 1.3760 −0.1140 0.0540
seismic in 0°
C 87 - 1.2D + 1.0
154 38.9160 −5.7020 −2.7480 1.6460 −0.0510 0.0670
seismic in 30°
C 88 - 1.2D + 1.0
154 80.4940 −10.9250 −5.7810 1.5950 −0.1730 0.0620
seismic in 60°
C 89 - 1.2D + 1.0
154 110.9310 −14.6880 −8.1050 1.2370 −0.4480 0.0410
seismic in 90°
C 90 - 1.2D + 1.0
154 122.0720 −15.9830 −9.0980 0.6680 −0.8010 0.0080
seismic in 120°
C 91 - 1.2D + 1.0
154 110.9310 −14.4630 −8.4950 0.0400 −1.1390 −0.0260
seismic in 150°
C 92 - 1.2D + 1.0
154 80.4940 −10.5350 −6.4570 −0.4780 −1.3700 −0.0540
seismic in 180°
C 93 - 1.2D + 1.0
154 38.9160 −5.2510 −3.5290 −0.7480 −1.4330 −0.0670
seismic in 210°
C 94 - 1.2D + 1.0
154 −2.6630 −0.0280 −0.4970 −0.6970 −1.3110 −0.0630
seismic in 240°
C 95 - 1.2D + 1.0
154 −33.1000 3.7350 1.8270 −0.3390 −1.0360 −0.0410
seismic in 270°
C 96 - 1.2D + 1.0
154 −44.2410 5.0300 2.8210 0.2300 −0.6830 −0.0090
seismic in 300°
C 97 - 1.2D + 1.0
154 −33.1000 3.5100 2.2180 0.8580 −0.3450 0.0260
seismic in 330°
Print Date:04/01/2022 OpenTower CE : 10.02.00.44 Page 36 of 43
Tower Reaction Summary Cont...
Overturning Overturning
Torque
Node Id Load Combination Vertical (kN) Shear x (kN) Shear z (kN) Moment Moment
(kNm)
(Mx) (kNm) (Mz) (kNm)
seismic in 330°
C 98 - 0.9D + 1.0
154 −12.3920 0.9510 0.9640 1.2640 0.0720 0.0540
seismic in 0°
C 99 - 0.9D + 1.0
154 29.1870 −4.3330 −1.9640 1.5330 0.1350 0.0670
seismic in 30°
C 2 - 1.2D + 1.6Wo-
156 −428.5860 −56.0100 40.0870 14.5780 −4.8300 −0.5900
0°
C 3 - 1.2D + 1.6Wo-
156 −755.6170 −102.8840 62.0270 7.2440 0.6450 −0.4880
30°
C 4 - 1.2D + 1.6Wo-
156 −866.8890 −120.3610 66.9090 −1.0350 5.8710 −0.1150
60°
C 5 - 1.2D + 1.6Wo-
156 −755.9060 −107.3090 54.4740 −9.3070 10.2100 0.3280
90°
C 6 - 1.2D + 1.6Wo-
156 −441.9020 −65.5620 27.0350 −15.5000 12.3700 0.6910
120°
Overturning Overturning
Torque
Node Id Load Combination Vertical (kN) Shear x (kN) Shear z (kN) Moment Moment
(kNm)
(Mx) (kNm) (Mz) (kNm)
C 7 - 1.2D + 1.6Wo-
156 37.3510 0.8500 −11.0720 −16.8930 10.7350 0.7660
150°
C 8 - 1.2D + 1.6Wo-
156 486.5830 64.2990 −44.3140 −13.0300 6.3460 0.6350
180°
C 9 - 1.2D + 1.6Wo-
156 814.3610 111.7900 −67.1000 −6.5190 0.8480 0.4300
210°
C 10 - 1.2D + 1.6Wo-
156 948.7480 133.3530 −74.3520 1.4880 −4.9300 0.0980
240°
C 11 - 1.2D + 1.6Wo-
156 820.5260 116.9510 −59.8050 10.3260 −8.8100 −0.3050
270°
C 12 - 1.2D + 1.6Wo-
156 498.7710 73.4280 −31.7030 16.3170 −10.4450 −0.5950
300°
C 13 - 1.2D + 1.6Wo-
156 52.2650 11.7800 3.9670 17.9370 −9.1800 −0.7040
330°
C 14 - 0.9D + 1.6Wo-
156 −437.9200 −57.3660 40.8500 14.4630 −5.0170 −0.5890
0°
C 15 - 0.9D + 1.6Wo-
156 −764.9510 −104.2410 62.7890 7.1290 0.4580 −0.4870
30°
C 16 - 0.9D + 1.6Wo-
156 −876.2230 −121.7180 67.6720 −1.1500 5.6840 −0.1140
60°
C 17 - 0.9D + 1.6Wo-
156 −765.2400 −108.6660 55.2360 −9.4220 10.0230 0.3300
90°
C 18 - 0.9D + 1.6Wo-
156 −451.2360 −66.9190 27.7980 −15.6160 12.1830 0.6930
120°
C 19 - 0.9D + 1.6Wo-
156 28.0170 −0.5060 −10.3090 −17.0080 10.5470 0.7680
150°
C 20 - 0.9D + 1.6Wo-
156 477.2490 62.9430 −43.5510 −13.1450 6.1590 0.6370
180°
C 21 - 0.9D + 1.6Wo-
156 805.0280 110.4330 −66.3380 −6.6340 0.6610 0.4320
210°
C 22 - 0.9D + 1.6Wo-
156 939.4140 131.9960 −73.5890 1.3730 −5.1170 0.1000
240°
C 23 - 0.9D + 1.6Wo-
156 811.1920 115.5940 −59.0420 10.2100 −8.9970 −0.3040
270°
C 24 - 0.9D + 1.6Wo-
156 489.4380 72.0710 −30.9400 16.2010 −10.6330 −0.5940
300°
C 25 - 0.9D + 1.6Wo-
156 42.9310 10.4230 4.7300 17.8210 −9.3670 −0.7030
330°
Print Date:04/01/2022 OpenTower CE : 10.02.00.44 Page 38 of 43
Tower Reaction Summary Cont...
Overturning Overturning
Torque
Node Id Load Combination Vertical (kN) Shear x (kN) Shear z (kN) Moment Moment
(kNm)
(Mx) (kNm) (Mz) (kNm)
330°
C 26 - 1.2D + 1.6Wo-
156 −269.8520 −34.9320 25.1680 9.5290 −2.9510 −0.3580
0°:PL1
C 27 - 1.2D + 1.6Wo-
156 −424.2480 −55.5850 39.9080 14.6870 −4.7570 −0.6180
0°:PL2
C 28 - 1.2D + 1.6Wo-
156 −485.4080 −65.6610 39.6080 4.7420 0.5260 −0.3040
30°:PL1
C 29 - 1.2D + 1.6Wo-
156 −748.2970 −102.1990 61.6680 7.3710 0.8000 −0.5040
30°:PL2
C 30 - 1.2D + 1.6Wo-
156 −558.6780 −77.0920 42.8590 −0.6240 3.8850 −0.0770
60°:PL1
C 31 - 1.2D + 1.6Wo-
156 −858.6250 −119.6060 66.4730 −0.9220 6.0640 −0.1150
60°:PL2
C 32 - 1.2D + 1.6Wo-
156 −485.4170 −68.4900 34.7440 −5.9580 6.7160 0.1960
90°:PL1
C 33 - 1.2D + 1.6Wo-
156 −748.7630 −106.6710 54.0700 −9.2360 10.3920 0.3440
90°:PL2
C 34 - 1.2D + 1.6Wo-
156 −278.4050 −41.0760 16.7770 −9.9230 8.1760 0.4190
120°:PL1
C 35 - 1.2D + 1.6Wo-
156 −437.6660 −65.2030 26.7640 −15.4910 12.4970 0.7180
120°:PL2
C 36 - 1.2D + 1.6Wo-
156 37.3460 2.4840 −8.2090 −10.7630 7.2080 0.4640
150°:PL1
C 37 - 1.2D + 1.6Wo-
156 37.3510 0.8180 −11.1280 −16.9480 10.7670 0.7980
150°:PL2
C 38 - 1.2D + 1.6Wo-
156 333.5800 44.1080 −30.0470 −8.2020 4.4590 0.3830
180°:PL1
C 39 - 1.2D + 1.6Wo-
156 482.3480 63.8850 −44.1390 −13.1360 6.2750 0.6630
180°:PL2
C 40 - 1.2D + 1.6Wo-
156 549.7250 75.2480 −45.0410 −3.9480 0.9690 0.2610
210°:PL1
C 41 - 1.2D + 1.6Wo-
156 807.0410 111.1040 −66.7420 −6.6460 0.6930 0.4460
210°:PL2
C 42 - 1.2D + 1.6Wo-
156 638.2260 89.3530 −49.8430 1.2440 −2.7440 0.0620
240°:PL1
C 43 - 1.2D + 1.6Wo-
156 940.2780 132.5780 −73.9050 1.3730 −5.1280 0.0980
240°:PL2
Overturning Overturning
Torque
Node Id Load Combination Vertical (kN) Shear x (kN) Shear z (kN) Moment Moment
(kNm)
(Mx) (kNm) (Mz) (kNm)
C 44 - 1.2D + 1.6Wo-
156 553.5550 78.5550 −40.3450 6.9440 −5.2820 −0.1850
270°:PL1
C 45 - 1.2D + 1.6Wo-
156 813.3830 116.3130 −59.4010 10.2560 −8.9920 −0.3210
270°:PL2
C 46 - 1.2D + 1.6Wo-
156 341.4020 49.9780 −21.9400 10.7770 −6.4040 −0.3620
300°:PL1
C 47 - 1.2D + 1.6Wo-
156 494.6390 73.0770 −31.4380 16.3070 −10.5690 −0.6220
300°:PL2
C 48 - 1.2D + 1.6Wo-
156 47.0390 9.5240 1.4560 11.7650 −5.6730 −0.4280
330°:PL1
C 49 - 1.2D + 1.6Wo-
156 52.2650 11.8120 4.0230 17.9920 −9.2120 −0.7360
330°:PL2
C 50 - 0.9D + 1.6Wo-
156 −279.1860 −36.2890 25.9310 9.4140 −3.1380 −0.3560
0°:PL1
C 51 - 0.9D + 1.6Wo-
156 −433.5820 −56.9410 40.6710 14.5710 −4.9440 −0.6170
0°:PL2
C 52 - 0.9D + 1.6Wo-
156 −494.7420 −67.0180 40.3710 4.6270 0.3390 −0.3020
30°:PL1
C 53 - 0.9D + 1.6Wo-
156 −757.6310 −103.5550 62.4310 7.2560 0.6130 −0.5030
30°:PL2
C 54 - 0.9D + 1.6Wo-
156 −568.0120 −78.4480 43.6220 −0.7390 3.6980 −0.0760
60°:PL1
C 55 - 0.9D + 1.6Wo-
156 −867.9590 −120.9620 67.2360 −1.0380 5.8770 −0.1140
60°:PL2
C 56 - 0.9D + 1.6Wo-
156 −494.7510 −69.8460 35.5070 −6.0740 6.5290 0.1970
90°:PL1
C 57 - 0.9D + 1.6Wo-
156 −758.0970 −108.0280 54.8330 −9.3520 10.2050 0.3460
90°:PL2
C 58 - 0.9D + 1.6Wo-
156 −287.7380 −42.4330 17.5390 −10.0390 7.9890 0.4210
120°:PL1
C 59 - 0.9D + 1.6Wo-
156 −446.9990 −66.5590 27.5270 −15.6060 12.3090 0.7200
120°:PL2
C 60 - 0.9D + 1.6Wo-
156 28.0120 1.1270 −7.4470 −10.8790 7.0200 0.4660
150°:PL1
C 61 - 0.9D + 1.6Wo-
156 28.0170 −0.5380 −10.3650 −17.0630 10.5790 0.8000
150°:PL2
C 62 - 0.9D + 1.6Wo-
156 324.2470 42.7520 −29.2840 −8.3170 4.2710 0.3840
180°:PL1
Print Date:04/01/2022 OpenTower CE : 10.02.00.44 Page 40 of 43
Tower Reaction Summary Cont...
Overturning Overturning
Torque
Node Id Load Combination Vertical (kN) Shear x (kN) Shear z (kN) Moment Moment
(kNm)
(Mx) (kNm) (Mz) (kNm)
180°:PL1
C 63 - 0.9D + 1.6Wo-
156 473.0140 62.5280 −43.3760 −13.2510 6.0880 0.6640
180°:PL2
C 64 - 0.9D + 1.6Wo-
156 540.3920 73.8910 −44.2790 −4.0640 0.7810 0.2630
210°:PL1
C 65 - 0.9D + 1.6Wo-
156 797.7080 109.7480 −65.9790 −6.7620 0.5050 0.4480
210°:PL2
C 66 - 0.9D + 1.6Wo-
156 628.8920 87.9970 −49.0810 1.1280 −2.9310 0.0630
240°:PL1
C 67 - 0.9D + 1.6Wo-
156 930.9440 131.2210 −73.1420 1.2570 −5.3150 0.1000
240°:PL2
C 68 - 0.9D + 1.6Wo-
156 544.2210 77.1990 −39.5820 6.8280 −5.4690 −0.1840
270°:PL1
C 69 - 0.9D + 1.6Wo-
156 804.0490 114.9560 −58.6380 10.1400 −9.1790 −0.3190
270°:PL2
C 70 - 0.9D + 1.6Wo-
156 332.0680 48.6220 −21.1770 10.6610 −6.5910 −0.3610
300°:PL1
C 71 - 0.9D + 1.6Wo-
156 485.3050 71.7200 −30.6760 16.1920 −10.7560 −0.6200
300°:PL2
C 72 - 0.9D + 1.6Wo-
156 37.7050 8.1670 2.2180 11.6490 −5.8600 −0.4270
330°:PL1
C 73 - 0.9D + 1.6Wo-
156 42.9310 10.4550 4.7860 17.8770 −9.3990 −0.7350
330°:PL2
C 74 - 1.0D + 1.0Ws-
156 −16.9360 −1.8740 2.0250 1.9830 0.0410 −0.0810
0°
C 75 - 1.0D + 1.0Ws-
156 −50.7490 −6.8060 4.3200 1.2200 0.6690 −0.0630
30°
C 76 - 1.0D + 1.0Ws-
156 −62.3100 −8.6660 4.8130 0.3180 1.2570 −0.0160
60°
C 77 - 1.0D + 1.0Ws-
156 −50.7760 −7.3000 3.4740 −0.6050 1.7230 0.0380
90°
C 78 - 1.0D + 1.0Ws-
156 −18.2280 −2.9140 0.5620 −1.3150 1.9290 0.0810
120°
C 79 - 1.0D + 1.0Ws-
156 31.1160 4.0120 −3.4340 −1.5180 1.7190 0.0920
150°
C 80 - 1.0D + 1.0Ws-
156 77.5440 10.6680 −6.9270 −1.1540 1.2080 0.0760
180°
Overturning Overturning
Torque
Node Id Load Combination Vertical (kN) Shear x (kN) Shear z (kN) Moment Moment
(kNm)
(Mx) (kNm) (Mz) (kNm)
C 81 - 1.0D + 1.0Ws-
156 111.4290 15.6600 −9.3050 −0.4710 0.5790 0.0480
210°
C 82 - 1.0D + 1.0Ws-
156 125.2310 17.9160 −10.0280 0.4050 −0.0640 0.0050
240°
C 83 - 1.0D + 1.0Ws-
156 112.0250 16.2260 −8.4840 1.3830 −0.4850 −0.0450
270°
C 84 - 1.0D + 1.0Ws-
156 78.7250 11.6670 −5.5080 2.0730 −0.6400 −0.0820
300°
C 85 - 1.0D + 1.0Ws-
156 32.5590 5.2030 −1.7480 2.2990 −0.4660 −0.0950
330°
C 86 - 1.2D + 1.0
156 −4.2440 0.3660 0.2650 1.3840 0.1240 −0.0390
seismic in 0°
C 87 - 1.2D + 1.0
156 −34.6810 −3.5630 2.3040 0.8660 0.3540 −0.0170
seismic in 30°
C 88 - 1.2D + 1.0
156 −45.8220 −5.0840 2.9080 0.2410 0.6910 0.0070
seismic in 60°
C 89 - 1.2D + 1.0
156 −34.6810 −3.7880 1.9160 −0.3260 1.0430 0.0270
seismic in 90°
C 90 - 1.2D + 1.0
156 −4.2440 −0.0240 −0.4080 −0.6820 1.3160 0.0390
seismic in 120°
C 91 - 1.2D + 1.0
156 37.3350 5.2010 −3.4390 −0.7310 1.4370 0.0380
seismic in 150°
C 92 - 1.2D + 1.0
156 78.9130 10.4860 −6.3670 −0.4610 1.3740 0.0260
seismic in 180°
C 93 - 1.2D + 1.0
156 109.3500 14.4150 −8.4060 0.0560 1.1430 0.0040
seismic in 210°
C 94 - 1.2D + 1.0
156 120.4910 15.9350 −9.0100 0.6820 0.8070 −0.0200
seismic in 240°
C 95 - 1.2D + 1.0
156 109.3510 14.6390 −8.0170 1.2480 0.4550 −0.0400
seismic in 270°
C 96 - 1.2D + 1.0
156 78.9130 10.8750 −5.6940 1.6040 0.1820 −0.0520
seismic in 300°
C 97 - 1.2D + 1.0
156 37.3350 5.6500 −2.6620 1.6540 0.0600 −0.0510
seismic in 330°
C 98 - 0.9D + 1.0
156 −13.5770 −0.9910 1.0280 1.2680 −0.0640 −0.0370
seismic in 0°
C 99 - 0.9D + 1.0
156 −44.0150 −4.9200 3.0670 0.7510 0.1670 −0.0160
seismic in 30°
Print Date:04/01/2022 OpenTower CE : 10.02.00.44 Page 42 of 43
Tower Reaction Summary Cont...
Overturning Overturning
Torque
Node Id Load Combination Vertical (kN) Shear x (kN) Shear z (kN) Moment Moment
(kNm)
(Mx) (kNm) (Mz) (kNm)
seismic in 30°
5 CONDITION OF ANALYSIS
This CALCULATION REPORT has been prepared based on the site inspection and the relevant information
and data provided to the undersigned. The conclusion and recommendation contained in this report
pertain only to the computer analysis of this structure and its load carrying capacity.
6 REFERENCES
• Association of Structural Engineers of the Philippines, National Structural Code of the Philippines 2015,
Volume I, Buildings, Towers, and Other Vertical Structures, 7th Edition. Chapter 1.
• Association of Structural Engineers of the Philippines, National Structural Code of the Philippines 2015,
Volume I, Buildings, Towers, and Other Vertical Structures, 7th Edition. Chapter 2.
• Association of Structural Engineers of the Philippines, National Structural Code of the Philippines 2015,
Volume I, Buildings, Towers, and Other Vertical Structures, 7th Edition. Chapter 4.
• Association of Structural Engineers of the Philippines, National Structural Code of the Philippines 2015,
Volume I, Buildings, Towers, and Other Vertical Structures, 7th Edition. Chapter 5.
• American Concrete Institute ACI-318-14M, Building Code Requirements for Concrete Works.
• AISC Manual of Steel Construction, “Specification for Design Fabrication and Erection of Structural Steel ”
15th Edition, 2016